diff options
Diffstat (limited to 'drivers/serial/8250.c')
-rw-r--r-- | drivers/serial/8250.c | 125 |
1 files changed, 111 insertions, 14 deletions
diff --git a/drivers/serial/8250.c b/drivers/serial/8250.c index 90621c3..48e259a 100644 --- a/drivers/serial/8250.c +++ b/drivers/serial/8250.c @@ -251,9 +251,16 @@ static const struct serial8250_config uart_config[] = { .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10, .flags = UART_CAP_FIFO | UART_CAP_UUE, }, + [PORT_RM9000] = { + .name = "RM9000", + .fifo_size = 16, + .tx_loadsz = 16, + .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10, + .flags = UART_CAP_FIFO, + }, }; -#ifdef CONFIG_SERIAL_8250_AU1X00 +#if defined (CONFIG_SERIAL_8250_AU1X00) /* Au1x00 UART hardware has a weird register layout */ static const u8 au_io_in_map[] = { @@ -289,6 +296,44 @@ static inline int map_8250_out_reg(struct uart_8250_port *up, int offset) return au_io_out_map[offset]; } +#elif defined (CONFIG_SERIAL_8250_RM9K) + +static const u8 + regmap_in[8] = { + [UART_RX] = 0x00, + [UART_IER] = 0x0c, + [UART_IIR] = 0x14, + [UART_LCR] = 0x1c, + [UART_MCR] = 0x20, + [UART_LSR] = 0x24, + [UART_MSR] = 0x28, + [UART_SCR] = 0x2c + }, + regmap_out[8] = { + [UART_TX] = 0x04, + [UART_IER] = 0x0c, + [UART_FCR] = 0x18, + [UART_LCR] = 0x1c, + [UART_MCR] = 0x20, + [UART_LSR] = 0x24, + [UART_MSR] = 0x28, + [UART_SCR] = 0x2c + }; + +static inline int map_8250_in_reg(struct uart_8250_port *up, int offset) +{ + if (up->port.iotype != UPIO_RM9000) + return offset; + return regmap_in[offset]; +} + +static inline int map_8250_out_reg(struct uart_8250_port *up, int offset) +{ + if (up->port.iotype != UPIO_RM9000) + return offset; + return regmap_out[offset]; +} + #else /* sane hardware needs no mapping */ @@ -308,8 +353,10 @@ static unsigned int serial_in(struct uart_8250_port *up, int offset) return inb(up->port.iobase + 1); case UPIO_MEM: + case UPIO_DWAPB: return readb(up->port.membase + offset); + case UPIO_RM9000: case UPIO_MEM32: return readl(up->port.membase + offset); @@ -333,6 +380,8 @@ static unsigned int serial_in(struct uart_8250_port *up, int offset) static void serial_out(struct uart_8250_port *up, int offset, int value) { + /* Save the offset before it's remapped */ + int save_offset = offset; offset = map_8250_out_reg(up, offset) << up->port.regshift; switch (up->port.iotype) { @@ -345,6 +394,7 @@ serial_out(struct uart_8250_port *up, int offset, int value) writeb(value, up->port.membase + offset); break; + case UPIO_RM9000: case UPIO_MEM32: writel(value, up->port.membase + offset); break; @@ -359,6 +409,18 @@ serial_out(struct uart_8250_port *up, int offset, int value) writeb(value, up->port.membase + offset); break; + case UPIO_DWAPB: + /* Save the LCR value so it can be re-written when a + * Busy Detect interrupt occurs. */ + if (save_offset == UART_LCR) + up->lcr = value; + writeb(value, up->port.membase + offset); + /* Read the IER to ensure any interrupt is cleared before + * returning from ISR. */ + if (save_offset == UART_TX || save_offset == UART_IER) + value = serial_in(up, UART_IER); + break; + default: outb(value, up->port.iobase + offset); } @@ -373,6 +435,7 @@ serial_out_sync(struct uart_8250_port *up, int offset, int value) #ifdef CONFIG_SERIAL_8250_AU1X00 case UPIO_AU: #endif + case UPIO_DWAPB: serial_out(up, offset, value); serial_in(up, UART_LCR); /* safe, no side-effects */ break; @@ -403,7 +466,7 @@ static inline void _serial_dl_write(struct uart_8250_port *up, int value) serial_outp(up, UART_DLM, value >> 8 & 0xff); } -#ifdef CONFIG_SERIAL_8250_AU1X00 +#if defined (CONFIG_SERIAL_8250_AU1X00) /* Au1x00 haven't got a standard divisor latch */ static int serial_dl_read(struct uart_8250_port *up) { @@ -420,6 +483,24 @@ static void serial_dl_write(struct uart_8250_port *up, int value) else _serial_dl_write(up, value); } +#elif defined (CONFIG_SERIAL_8250_RM9K) +static int serial_dl_read(struct uart_8250_port *up) +{ + return (up->port.iotype == UPIO_RM9000) ? + (((__raw_readl(up->port.membase + 0x10) << 8) | + (__raw_readl(up->port.membase + 0x08) & 0xff)) & 0xffff) : + _serial_dl_read(up); +} + +static void serial_dl_write(struct uart_8250_port *up, int value) +{ + if (up->port.iotype == UPIO_RM9000) { + __raw_writel(value, up->port.membase + 0x08); + __raw_writel(value >> 8, up->port.membase + 0x10); + } else { + _serial_dl_write(up, value); + } +} #else #define serial_dl_read(up) _serial_dl_read(up) #define serial_dl_write(up, value) _serial_dl_write(up, value) @@ -621,7 +702,7 @@ static unsigned int autoconfig_read_divisor_id(struct uart_8250_port *p) * its clones. (We treat the broken original StarTech 16650 V1 as a * 16550, and why not? Startech doesn't seem to even acknowledge its * existence.) - * + * * What evil have men's minds wrought... */ static void autoconfig_has_efr(struct uart_8250_port *up) @@ -674,7 +755,7 @@ static void autoconfig_has_efr(struct uart_8250_port *up) up->bugs |= UART_BUG_QUOT; return; } - + /* * We check for a XR16C850 by setting DLL and DLM to 0, and then * reading back DLL and DLM. The chip type depends on the DLM @@ -817,7 +898,7 @@ static void autoconfig_16550a(struct uart_8250_port *up) status1 &= ~0xB0; /* Disable LOCK, mask out PRESL[01] */ status1 |= 0x10; /* 1.625 divisor for baud_base --> 921600 */ serial_outp(up, 0x04, status1); - + serial_dl_write(up, quot); serial_outp(up, UART_LCR, 0); @@ -913,7 +994,6 @@ static void autoconfig(struct uart_8250_port *up, unsigned int probeflags) * be frobbing the chips IRQ enable register to see if it exists. */ spin_lock_irqsave(&up->port.lock, flags); -// save_flags(flags); cli(); up->capabilities = 0; up->bugs = 0; @@ -922,7 +1002,7 @@ static void autoconfig(struct uart_8250_port *up, unsigned int probeflags) /* * Do a simple existence test first; if we fail this, * there's no point trying anything else. - * + * * 0x80 is used as a nonsense port to prevent against * false positives due to ISA bus float. The * assumption is that 0x80 is a non-existent port; @@ -961,7 +1041,7 @@ static void autoconfig(struct uart_8250_port *up, unsigned int probeflags) save_mcr = serial_in(up, UART_MCR); save_lcr = serial_in(up, UART_LCR); - /* + /* * Check to see if a UART is really there. Certain broken * internal modems based on the Rockwell chipset fail this * test, because they apparently don't implement the loopback @@ -1068,9 +1148,8 @@ static void autoconfig(struct uart_8250_port *up, unsigned int probeflags) else serial_outp(up, UART_IER, 0); - out: + out: spin_unlock_irqrestore(&up->port.lock, flags); -// restore_flags(flags); DEBUG_AUTOCONF("type=%s\n", uart_config[up->port.type].name); } @@ -1094,7 +1173,7 @@ static void autoconfig_irq(struct uart_8250_port *up) save_mcr = serial_inp(up, UART_MCR); save_ier = serial_inp(up, UART_IER); serial_outp(up, UART_MCR, UART_MCR_OUT1 | UART_MCR_OUT2); - + irqs = probe_irq_on(); serial_outp(up, UART_MCR, 0); udelay (10); @@ -1159,8 +1238,11 @@ static void serial8250_start_tx(struct uart_port *port) if (up->bugs & UART_BUG_TXEN) { unsigned char lsr, iir; lsr = serial_in(up, UART_LSR); - iir = serial_in(up, UART_IIR); - if (lsr & UART_LSR_TEMT && iir & UART_IIR_NO_INT) + iir = serial_in(up, UART_IIR) & 0x0f; + if ((up->port.type == PORT_RM9000) ? + (lsr & UART_LSR_THRE && + (iir == UART_IIR_NO_INT || iir == UART_IIR_THRI)) : + (lsr & UART_LSR_TEMT && iir & UART_IIR_NO_INT)) transmit_chars(up); } } @@ -1389,6 +1471,19 @@ static irqreturn_t serial8250_interrupt(int irq, void *dev_id) handled = 1; end = NULL; + } else if (up->port.iotype == UPIO_DWAPB && + (iir & UART_IIR_BUSY) == UART_IIR_BUSY) { + /* The DesignWare APB UART has an Busy Detect (0x07) + * interrupt meaning an LCR write attempt occured while the + * UART was busy. The interrupt must be cleared by reading + * the UART status register (USR) and the LCR re-written. */ + unsigned int status; + status = *(volatile u32 *)up->port.private_data; + serial_out(up, UART_LCR, up->lcr); + + handled = 1; + + end = NULL; } else if (end == NULL) end = l; @@ -1928,7 +2023,7 @@ serial8250_set_termios(struct uart_port *port, struct ktermios *termios, /* * Ask the core to calculate the divisor for us. */ - baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16); + baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16); quot = serial8250_get_divisor(port, baud); /* @@ -2090,6 +2185,7 @@ static int serial8250_request_std_resource(struct uart_8250_port *up) case UPIO_TSI: case UPIO_MEM32: case UPIO_MEM: + case UPIO_DWAPB: if (!up->port.mapbase) break; @@ -2127,6 +2223,7 @@ static void serial8250_release_std_resource(struct uart_8250_port *up) case UPIO_TSI: case UPIO_MEM32: case UPIO_MEM: + case UPIO_DWAPB: if (!up->port.mapbase) break; |