diff options
Diffstat (limited to 'drivers/usb/storage')
| -rw-r--r-- | drivers/usb/storage/scsiglue.c | 54 | ||||
| -rw-r--r-- | drivers/usb/storage/scsiglue.h | 1 | ||||
| -rw-r--r-- | drivers/usb/storage/transport.c | 116 | ||||
| -rw-r--r-- | drivers/usb/storage/transport.h | 1 |
4 files changed, 99 insertions, 73 deletions
diff --git a/drivers/usb/storage/scsiglue.c b/drivers/usb/storage/scsiglue.c index e43eddc..af294bb 100644 --- a/drivers/usb/storage/scsiglue.c +++ b/drivers/usb/storage/scsiglue.c @@ -155,6 +155,15 @@ static int slave_configure(struct scsi_device *sdev) * If this device makes that mistake, tell the sd driver. */ if (us->flags & US_FL_FIX_CAPACITY) sdev->fix_capacity = 1; + + /* USB-IDE bridges tend to report SK = 0x04 (Non-recoverable + * Hardware Error) when any low-level error occurs, + * recoverable or not. Setting this flag tells the SCSI + * midlayer to retry such commands, which frequently will + * succeed and fix the error. The worst this can lead to + * is an occasional series of retries that will all fail. */ + sdev->retry_hwerror = 1; + } else { /* Non-disk-type devices don't need to blacklist any pages @@ -255,50 +264,23 @@ static int device_reset(struct scsi_cmnd *srb) /* lock the device pointers and do the reset */ down(&(us->dev_semaphore)); - if (test_bit(US_FLIDX_DISCONNECTING, &us->flags)) { - result = FAILED; - US_DEBUGP("No reset during disconnect\n"); - } else - result = us->transport_reset(us); + result = us->transport_reset(us); up(&(us->dev_semaphore)); - return result; + return result < 0 ? FAILED : SUCCESS; } -/* This resets the device's USB port. */ -/* It refuses to work if there's more than one interface in - * the device, so that other users are not affected. */ +/* Simulate a SCSI bus reset by resetting the device's USB port. */ /* This is always called with scsi_lock(host) held */ static int bus_reset(struct scsi_cmnd *srb) { struct us_data *us = host_to_us(srb->device->host); - int result, rc; + int result; US_DEBUGP("%s called\n", __FUNCTION__); - /* The USB subsystem doesn't handle synchronisation between - * a device's several drivers. Therefore we reset only devices - * with just one interface, which we of course own. */ - down(&(us->dev_semaphore)); - if (test_bit(US_FLIDX_DISCONNECTING, &us->flags)) { - result = -EIO; - US_DEBUGP("No reset during disconnect\n"); - } else if (us->pusb_dev->actconfig->desc.bNumInterfaces != 1) { - result = -EBUSY; - US_DEBUGP("Refusing to reset a multi-interface device\n"); - } else { - rc = usb_lock_device_for_reset(us->pusb_dev, us->pusb_intf); - if (rc < 0) { - US_DEBUGP("unable to lock device for reset: %d\n", rc); - result = rc; - } else { - result = usb_reset_device(us->pusb_dev); - if (rc) - usb_unlock_device(us->pusb_dev); - US_DEBUGP("usb_reset_device returns %d\n", result); - } - } + result = usb_stor_port_reset(us); up(&(us->dev_semaphore)); /* lock the host for the return */ @@ -320,6 +302,14 @@ void usb_stor_report_device_reset(struct us_data *us) } } +/* Report a driver-initiated bus reset to the SCSI layer. + * Calling this for a SCSI-initiated reset is unnecessary but harmless. + * The caller must own the SCSI host lock. */ +void usb_stor_report_bus_reset(struct us_data *us) +{ + scsi_report_bus_reset(us_to_host(us), 0); +} + /*********************************************************************** * /proc/scsi/ functions ***********************************************************************/ diff --git a/drivers/usb/storage/scsiglue.h b/drivers/usb/storage/scsiglue.h index d0a49af..737e4fa 100644 --- a/drivers/usb/storage/scsiglue.h +++ b/drivers/usb/storage/scsiglue.h @@ -42,6 +42,7 @@ #define _SCSIGLUE_H_ extern void usb_stor_report_device_reset(struct us_data *us); +extern void usb_stor_report_bus_reset(struct us_data *us); extern unsigned char usb_stor_sense_invalidCDB[18]; extern struct scsi_host_template usb_stor_host_template; diff --git a/drivers/usb/storage/transport.c b/drivers/usb/storage/transport.c index 9743e28..e6b1c6c 100644 --- a/drivers/usb/storage/transport.c +++ b/drivers/usb/storage/transport.c @@ -266,8 +266,9 @@ int usb_stor_clear_halt(struct us_data *us, unsigned int pipe) NULL, 0, 3*HZ); /* reset the endpoint toggle */ - usb_settoggle(us->pusb_dev, usb_pipeendpoint(pipe), - usb_pipeout(pipe), 0); + if (result >= 0) + usb_settoggle(us->pusb_dev, usb_pipeendpoint(pipe), + usb_pipeout(pipe), 0); US_DEBUGP("%s: result = %d\n", __FUNCTION__, result); return result; @@ -540,15 +541,15 @@ void usb_stor_invoke_transport(struct scsi_cmnd *srb, struct us_data *us) */ if (test_bit(US_FLIDX_TIMED_OUT, &us->flags)) { US_DEBUGP("-- command was aborted\n"); - goto Handle_Abort; + srb->result = DID_ABORT << 16; + goto Handle_Errors; } /* if there is a transport error, reset and don't auto-sense */ if (result == USB_STOR_TRANSPORT_ERROR) { US_DEBUGP("-- transport indicates error, resetting\n"); - us->transport_reset(us); srb->result = DID_ERROR << 16; - return; + goto Handle_Errors; } /* if the transport provided its own sense data, don't auto-sense */ @@ -668,7 +669,8 @@ void usb_stor_invoke_transport(struct scsi_cmnd *srb, struct us_data *us) if (test_bit(US_FLIDX_TIMED_OUT, &us->flags)) { US_DEBUGP("-- auto-sense aborted\n"); - goto Handle_Abort; + srb->result = DID_ABORT << 16; + goto Handle_Errors; } if (temp_result != USB_STOR_TRANSPORT_GOOD) { US_DEBUGP("-- auto-sense failure\n"); @@ -677,9 +679,9 @@ void usb_stor_invoke_transport(struct scsi_cmnd *srb, struct us_data *us) * multi-target device, since failure of an * auto-sense is perfectly valid */ - if (!(us->flags & US_FL_SCM_MULT_TARG)) - us->transport_reset(us); srb->result = DID_ERROR << 16; + if (!(us->flags & US_FL_SCM_MULT_TARG)) + goto Handle_Errors; return; } @@ -720,12 +722,28 @@ void usb_stor_invoke_transport(struct scsi_cmnd *srb, struct us_data *us) return; - /* abort processing: the bulk-only transport requires a reset - * following an abort */ - Handle_Abort: - srb->result = DID_ABORT << 16; - if (us->protocol == US_PR_BULK) + /* Error and abort processing: try to resynchronize with the device + * by issuing a port reset. If that fails, try a class-specific + * device reset. */ + Handle_Errors: + + /* Let the SCSI layer know we are doing a reset, set the + * RESETTING bit, and clear the ABORTING bit so that the reset + * may proceed. */ + scsi_lock(us_to_host(us)); + usb_stor_report_bus_reset(us); + set_bit(US_FLIDX_RESETTING, &us->flags); + clear_bit(US_FLIDX_ABORTING, &us->flags); + scsi_unlock(us_to_host(us)); + + result = usb_stor_port_reset(us); + if (result < 0) { + scsi_lock(us_to_host(us)); + usb_stor_report_device_reset(us); + scsi_unlock(us_to_host(us)); us->transport_reset(us); + } + clear_bit(US_FLIDX_RESETTING, &us->flags); } /* Stop the current URB transfer */ @@ -1124,7 +1142,7 @@ int usb_stor_Bulk_transport(struct scsi_cmnd *srb, struct us_data *us) * It's handy that every transport mechanism uses the control endpoint for * resets. * - * Basically, we send a reset with a 20-second timeout, so we don't get + * Basically, we send a reset with a 5-second timeout, so we don't get * jammed attempting to do the reset. */ static int usb_stor_reset_common(struct us_data *us, @@ -1133,28 +1151,18 @@ static int usb_stor_reset_common(struct us_data *us, { int result; int result2; - int rc = FAILED; - /* Let the SCSI layer know we are doing a reset, set the - * RESETTING bit, and clear the ABORTING bit so that the reset - * may proceed. - */ - scsi_lock(us_to_host(us)); - usb_stor_report_device_reset(us); - set_bit(US_FLIDX_RESETTING, &us->flags); - clear_bit(US_FLIDX_ABORTING, &us->flags); - scsi_unlock(us_to_host(us)); + if (test_bit(US_FLIDX_DISCONNECTING, &us->flags)) { + US_DEBUGP("No reset during disconnect\n"); + return -EIO; + } - /* A 20-second timeout may seem rather long, but a LaCie - * StudioDrive USB2 device takes 16+ seconds to get going - * following a powerup or USB attach event. - */ result = usb_stor_control_msg(us, us->send_ctrl_pipe, request, requesttype, value, index, data, size, - 20*HZ); + 5*HZ); if (result < 0) { US_DEBUGP("Soft reset failed: %d\n", result); - goto Done; + return result; } /* Give the device some time to recover from the reset, @@ -1164,7 +1172,7 @@ static int usb_stor_reset_common(struct us_data *us, HZ*6); if (test_bit(US_FLIDX_DISCONNECTING, &us->flags)) { US_DEBUGP("Reset interrupted by disconnect\n"); - goto Done; + return -EIO; } US_DEBUGP("Soft reset: clearing bulk-in endpoint halt\n"); @@ -1173,17 +1181,14 @@ static int usb_stor_reset_common(struct us_data *us, US_DEBUGP("Soft reset: clearing bulk-out endpoint halt\n"); result2 = usb_stor_clear_halt(us, us->send_bulk_pipe); - /* return a result code based on the result of the control message */ - if (result < 0 || result2 < 0) { + /* return a result code based on the result of the clear-halts */ + if (result >= 0) + result = result2; + if (result < 0) US_DEBUGP("Soft reset failed\n"); - goto Done; - } - US_DEBUGP("Soft reset done\n"); - rc = SUCCESS; - - Done: - clear_bit(US_FLIDX_RESETTING, &us->flags); - return rc; + else + US_DEBUGP("Soft reset done\n"); + return result; } /* This issues a CB[I] Reset to the device in question @@ -1213,3 +1218,32 @@ int usb_stor_Bulk_reset(struct us_data *us) USB_TYPE_CLASS | USB_RECIP_INTERFACE, 0, us->ifnum, NULL, 0); } + +/* Issue a USB port reset to the device. But don't do anything if + * there's more than one interface in the device, so that other users + * are not affected. */ +int usb_stor_port_reset(struct us_data *us) +{ + int result, rc; + + if (test_bit(US_FLIDX_DISCONNECTING, &us->flags)) { + result = -EIO; + US_DEBUGP("No reset during disconnect\n"); + } else if (us->pusb_dev->actconfig->desc.bNumInterfaces != 1) { + result = -EBUSY; + US_DEBUGP("Refusing to reset a multi-interface device\n"); + } else { + result = rc = + usb_lock_device_for_reset(us->pusb_dev, us->pusb_intf); + if (result < 0) { + US_DEBUGP("unable to lock device for reset: %d\n", + result); + } else { + result = usb_reset_device(us->pusb_dev); + if (rc) + usb_unlock_device(us->pusb_dev); + US_DEBUGP("usb_reset_device returns %d\n", result); + } + } + return result; +} diff --git a/drivers/usb/storage/transport.h b/drivers/usb/storage/transport.h index e25f8d8..8d9e066 100644 --- a/drivers/usb/storage/transport.h +++ b/drivers/usb/storage/transport.h @@ -171,4 +171,5 @@ extern int usb_stor_bulk_transfer_buf(struct us_data *us, unsigned int pipe, extern int usb_stor_bulk_transfer_sg(struct us_data *us, unsigned int pipe, void *buf, unsigned int length, int use_sg, int *residual); +extern int usb_stor_port_reset(struct us_data *us); #endif |