diff options
Diffstat (limited to 'sound')
-rw-r--r-- | sound/soc/codecs/tlv320dac33.c | 125 | ||||
-rw-r--r-- | sound/soc/codecs/twl4030.c | 2 | ||||
-rw-r--r-- | sound/soc/omap/omap-mcbsp.c | 137 |
3 files changed, 156 insertions, 108 deletions
diff --git a/sound/soc/codecs/tlv320dac33.c b/sound/soc/codecs/tlv320dac33.c index 2fa946c..8651b01 100644 --- a/sound/soc/codecs/tlv320dac33.c +++ b/sound/soc/codecs/tlv320dac33.c @@ -49,8 +49,6 @@ #define NSAMPLE_MAX 5700 -#define LATENCY_TIME_MS 20 - #define MODE7_LTHR 10 #define MODE7_UTHR (DAC33_BUFFER_SIZE_SAMPLES - 10) @@ -62,6 +60,9 @@ #define US_TO_SAMPLES(rate, us) \ (rate / (1000000 / us)) +#define UTHR_FROM_PERIOD_SIZE(samples, playrate, burstrate) \ + ((samples * 5000) / ((burstrate * 5000) / (burstrate - playrate))) + static void dac33_calculate_times(struct snd_pcm_substream *substream); static int dac33_prepare_chip(struct snd_pcm_substream *substream); @@ -107,6 +108,10 @@ struct tlv320dac33_priv { * this */ enum dac33_fifo_modes fifo_mode;/* FIFO mode selection */ unsigned int nsample; /* burst read amount from host */ + int mode1_latency; /* latency caused by the i2c writes in + * us */ + int auto_fifo_config; /* Configure the FIFO based on the + * period size */ u8 burst_bclkdiv; /* BCLK divider value in burst mode */ unsigned int burst_rate; /* Interface speed in Burst modes */ @@ -538,13 +543,16 @@ static const struct snd_kcontrol_new dac33_snd_controls[] = { DAC33_LINEL_TO_LLO_VOL, DAC33_LINER_TO_RLO_VOL, 0, 127, 1), }; -static const struct snd_kcontrol_new dac33_nsample_snd_controls[] = { +static const struct snd_kcontrol_new dac33_mode_snd_controls[] = { + SOC_ENUM_EXT("FIFO Mode", dac33_fifo_mode_enum, + dac33_get_fifo_mode, dac33_set_fifo_mode), +}; + +static const struct snd_kcontrol_new dac33_fifo_snd_controls[] = { SOC_SINGLE_EXT("nSample", 0, 0, 5900, 0, - dac33_get_nsample, dac33_set_nsample), + dac33_get_nsample, dac33_set_nsample), SOC_SINGLE_EXT("UTHR", 0, 0, MODE7_UTHR, 0, dac33_get_uthr, dac33_set_uthr), - SOC_ENUM_EXT("FIFO Mode", dac33_fifo_mode_enum, - dac33_get_fifo_mode, dac33_set_fifo_mode), }; /* Analog bypass */ @@ -649,7 +657,7 @@ static inline void dac33_prefill_handler(struct tlv320dac33_priv *dac33) switch (dac33->fifo_mode) { case DAC33_FIFO_MODE1: dac33_write16(codec, DAC33_NSAMPLE_MSB, - DAC33_THRREG(dac33->nsample + dac33->alarm_threshold)); + DAC33_THRREG(dac33->nsample)); /* Take the timestamps */ spin_lock_irq(&dac33->lock); @@ -798,6 +806,10 @@ static void dac33_shutdown(struct snd_pcm_substream *substream, struct tlv320dac33_priv *dac33 = snd_soc_codec_get_drvdata(codec); dac33->substream = NULL; + + /* Reset the nSample restrictions */ + dac33->nsample_min = 0; + dac33->nsample_max = NSAMPLE_MAX; } static int dac33_hw_params(struct snd_pcm_substream *substream, @@ -1040,54 +1052,68 @@ static void dac33_calculate_times(struct snd_pcm_substream *substream) struct snd_soc_device *socdev = rtd->socdev; struct snd_soc_codec *codec = socdev->card->codec; struct tlv320dac33_priv *dac33 = snd_soc_codec_get_drvdata(codec); + unsigned int period_size = substream->runtime->period_size; + unsigned int rate = substream->runtime->rate; unsigned int nsample_limit; /* In bypass mode we don't need to calculate */ if (!dac33->fifo_mode) return; - /* Number of samples (16bit, stereo) in one period */ - dac33->nsample_min = snd_pcm_lib_period_bytes(substream) / 4; - - /* Number of samples (16bit, stereo) in ALSA buffer */ - dac33->nsample_max = snd_pcm_lib_buffer_bytes(substream) / 4; - /* Subtract one period from the total */ - dac33->nsample_max -= dac33->nsample_min; - - /* Number of samples for LATENCY_TIME_MS / 2 */ - dac33->alarm_threshold = substream->runtime->rate / - (1000 / (LATENCY_TIME_MS / 2)); - - /* Find and fix up the lowest nsmaple limit */ - nsample_limit = substream->runtime->rate / (1000 / LATENCY_TIME_MS); - - if (dac33->nsample_min < nsample_limit) - dac33->nsample_min = nsample_limit; - - if (dac33->nsample < dac33->nsample_min) - dac33->nsample = dac33->nsample_min; - - /* - * Find and fix up the highest nsmaple limit - * In order to not overflow the DAC33 buffer substract the - * alarm_threshold value from the size of the DAC33 buffer - */ - nsample_limit = DAC33_BUFFER_SIZE_SAMPLES - dac33->alarm_threshold; - - if (dac33->nsample_max > nsample_limit) - dac33->nsample_max = nsample_limit; - - if (dac33->nsample > dac33->nsample_max) - dac33->nsample = dac33->nsample_max; - switch (dac33->fifo_mode) { case DAC33_FIFO_MODE1: + /* Number of samples under i2c latency */ + dac33->alarm_threshold = US_TO_SAMPLES(rate, + dac33->mode1_latency); + if (dac33->auto_fifo_config) { + if (period_size <= dac33->alarm_threshold) + /* + * Configure nSamaple to number of periods, + * which covers the latency requironment. + */ + dac33->nsample = period_size * + ((dac33->alarm_threshold / period_size) + + (dac33->alarm_threshold % period_size ? + 1 : 0)); + else + dac33->nsample = period_size; + } else { + /* nSample time shall not be shorter than i2c latency */ + dac33->nsample_min = dac33->alarm_threshold; + /* + * nSample should not be bigger than alsa buffer minus + * size of one period to avoid overruns + */ + dac33->nsample_max = substream->runtime->buffer_size - + period_size; + nsample_limit = DAC33_BUFFER_SIZE_SAMPLES - + dac33->alarm_threshold; + if (dac33->nsample_max > nsample_limit) + dac33->nsample_max = nsample_limit; + + /* Correct the nSample if it is outside of the ranges */ + if (dac33->nsample < dac33->nsample_min) + dac33->nsample = dac33->nsample_min; + if (dac33->nsample > dac33->nsample_max) + dac33->nsample = dac33->nsample_max; + } + dac33->mode1_us_burst = SAMPLES_TO_US(dac33->burst_rate, dac33->nsample); dac33->t_stamp1 = 0; dac33->t_stamp2 = 0; break; case DAC33_FIFO_MODE7: + if (dac33->auto_fifo_config) { + dac33->uthr = UTHR_FROM_PERIOD_SIZE( + period_size, + rate, + dac33->burst_rate) + 9; + if (dac33->uthr > MODE7_UTHR) + dac33->uthr = MODE7_UTHR; + if (dac33->uthr < (MODE7_LTHR + 10)) + dac33->uthr = (MODE7_LTHR + 10); + } dac33->mode7_us_to_lthr = SAMPLES_TO_US(substream->runtime->rate, dac33->uthr - MODE7_LTHR + 1); @@ -1385,10 +1411,15 @@ static int dac33_soc_probe(struct platform_device *pdev) snd_soc_add_controls(codec, dac33_snd_controls, ARRAY_SIZE(dac33_snd_controls)); - /* Only add the nSample controls, if we have valid IRQ number */ - if (dac33->irq >= 0) - snd_soc_add_controls(codec, dac33_nsample_snd_controls, - ARRAY_SIZE(dac33_nsample_snd_controls)); + /* Only add the FIFO controls, if we have valid IRQ number */ + if (dac33->irq >= 0) { + snd_soc_add_controls(codec, dac33_mode_snd_controls, + ARRAY_SIZE(dac33_mode_snd_controls)); + /* FIFO usage controls only, if autoio config is not selected */ + if (!dac33->auto_fifo_config) + snd_soc_add_controls(codec, dac33_fifo_snd_controls, + ARRAY_SIZE(dac33_fifo_snd_controls)); + } dac33_add_widgets(codec); @@ -1519,6 +1550,10 @@ static int __devinit dac33_i2c_probe(struct i2c_client *client, /* Pre calculate the burst rate */ dac33->burst_rate = BURST_BASEFREQ_HZ / dac33->burst_bclkdiv / 32; dac33->keep_bclk = pdata->keep_bclk; + dac33->auto_fifo_config = pdata->auto_fifo_config; + dac33->mode1_latency = pdata->mode1_latency; + if (!dac33->mode1_latency) + dac33->mode1_latency = 10000; /* 10ms */ dac33->irq = client->irq; dac33->nsample = NSAMPLE_MAX; dac33->nsample_max = NSAMPLE_MAX; diff --git a/sound/soc/codecs/twl4030.c b/sound/soc/codecs/twl4030.c index bd557c2..d401c59 100644 --- a/sound/soc/codecs/twl4030.c +++ b/sound/soc/codecs/twl4030.c @@ -1432,11 +1432,9 @@ static const struct snd_soc_dapm_widget twl4030_dapm_widgets[] = { TX2 Left/Right: either analog Left/Right or Digimic1 */ SND_SOC_DAPM_MUX_E("TX1 Capture Route", SND_SOC_NOPM, 0, 0, &twl4030_dapm_micpathtx1_control, micpath_event, - SND_SOC_DAPM_POST_PMU|SND_SOC_DAPM_POST_PMD| SND_SOC_DAPM_POST_REG), SND_SOC_DAPM_MUX_E("TX2 Capture Route", SND_SOC_NOPM, 0, 0, &twl4030_dapm_micpathtx2_control, micpath_event, - SND_SOC_DAPM_POST_PMU|SND_SOC_DAPM_POST_PMD| SND_SOC_DAPM_POST_REG), /* Analog input mixers for the capture amplifiers */ diff --git a/sound/soc/omap/omap-mcbsp.c b/sound/soc/omap/omap-mcbsp.c index aebd3af..86f2139 100644 --- a/sound/soc/omap/omap-mcbsp.c +++ b/sound/soc/omap/omap-mcbsp.c @@ -155,13 +155,23 @@ static void omap_mcbsp_set_threshold(struct snd_pcm_substream *substream) struct snd_soc_pcm_runtime *rtd = substream->private_data; struct snd_soc_dai *cpu_dai = rtd->dai->cpu_dai; struct omap_mcbsp_data *mcbsp_data = to_mcbsp(cpu_dai->private_data); + struct omap_pcm_dma_data *dma_data; int dma_op_mode = omap_mcbsp_get_dma_op_mode(mcbsp_data->bus_id); int words; + dma_data = snd_soc_dai_get_dma_data(rtd->dai->cpu_dai, substream); + /* TODO: Currently, MODE_ELEMENT == MODE_FRAME */ if (dma_op_mode == MCBSP_DMA_MODE_THRESHOLD) - /* The FIFO size depends on the McBSP word configuration */ - words = snd_pcm_lib_period_bytes(substream) / + /* + * Configure McBSP threshold based on either: + * packet_size, when the sDMA is in packet mode, or + * based on the period size. + */ + if (dma_data->packet_size) + words = dma_data->packet_size; + else + words = snd_pcm_lib_period_bytes(substream) / (mcbsp_data->wlen / 8); else words = 1; @@ -192,31 +202,6 @@ static int omap_mcbsp_hwrule_min_buffersize(struct snd_pcm_hw_params *params, return snd_interval_refine(buffer_size, &frames); } -static int omap_mcbsp_hwrule_max_periodsize(struct snd_pcm_hw_params *params, - struct snd_pcm_hw_rule *rule) -{ - struct snd_interval *period_size = hw_param_interval(params, - SNDRV_PCM_HW_PARAM_PERIOD_SIZE); - struct snd_interval *channels = hw_param_interval(params, - SNDRV_PCM_HW_PARAM_CHANNELS); - struct snd_pcm_substream *substream = rule->private; - struct snd_soc_pcm_runtime *rtd = substream->private_data; - struct snd_soc_dai *cpu_dai = rtd->dai->cpu_dai; - struct omap_mcbsp_data *mcbsp_data = to_mcbsp(cpu_dai->private_data); - struct snd_interval frames; - int size; - - snd_interval_any(&frames); - if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK) - size = omap_mcbsp_get_max_tx_threshold(mcbsp_data->bus_id); - else - size = omap_mcbsp_get_max_rx_threshold(mcbsp_data->bus_id); - - frames.max = size / channels->min; - frames.integer = 1; - return snd_interval_refine(period_size, &frames); -} - static int omap_mcbsp_dai_startup(struct snd_pcm_substream *substream, struct snd_soc_dai *dai) { @@ -245,10 +230,8 @@ static int omap_mcbsp_dai_startup(struct snd_pcm_substream *substream, * 4 channels: size is 128 / 4 = 32 frames (4 * 32 words) */ if (cpu_is_omap343x()) { - int dma_op_mode = omap_mcbsp_get_dma_op_mode(bus_id); - /* - * The first rule is for the buffer size, we should not allow + * Rule for the buffer size. We should not allow * smaller buffer than the FIFO size to avoid underruns */ snd_pcm_hw_rule_add(substream->runtime, 0, @@ -257,17 +240,9 @@ static int omap_mcbsp_dai_startup(struct snd_pcm_substream *substream, mcbsp_data, SNDRV_PCM_HW_PARAM_BUFFER_SIZE, -1); - /* - * In case of threshold mode, the rule will ensure, that the - * period size is not bigger than the maximum allowed threshold - * value. - */ - if (dma_op_mode == MCBSP_DMA_MODE_THRESHOLD) - snd_pcm_hw_rule_add(substream->runtime, 0, - SNDRV_PCM_HW_PARAM_CHANNELS, - omap_mcbsp_hwrule_max_periodsize, - substream, - SNDRV_PCM_HW_PARAM_PERIOD_SIZE, -1); + /* Make sure, that the period size is always even */ + snd_pcm_hw_constraint_step(substream->runtime, 0, + SNDRV_PCM_HW_PARAM_PERIOD_SIZE, 2); } return err; @@ -348,11 +323,14 @@ static int omap_mcbsp_dai_hw_params(struct snd_pcm_substream *substream, struct snd_soc_dai *cpu_dai = rtd->dai->cpu_dai; struct omap_mcbsp_data *mcbsp_data = to_mcbsp(cpu_dai->private_data); struct omap_mcbsp_reg_cfg *regs = &mcbsp_data->regs; - int dma, bus_id = mcbsp_data->bus_id, id = cpu_dai->id; + struct omap_pcm_dma_data *dma_data; + int dma, bus_id = mcbsp_data->bus_id; int wlen, channels, wpf, sync_mode = OMAP_DMA_SYNC_ELEMENT; + int pkt_size = 0; unsigned long port; unsigned int format, div, framesize, master; + dma_data = &omap_mcbsp_dai_dma_params[cpu_dai->id][substream->stream]; if (cpu_class_is_omap1()) { dma = omap1_dma_reqs[bus_id][substream->stream]; port = omap1_mcbsp_port[bus_id][substream->stream]; @@ -365,35 +343,74 @@ static int omap_mcbsp_dai_hw_params(struct snd_pcm_substream *substream, } else if (cpu_is_omap343x()) { dma = omap24xx_dma_reqs[bus_id][substream->stream]; port = omap34xx_mcbsp_port[bus_id][substream->stream]; - omap_mcbsp_dai_dma_params[id][substream->stream].set_threshold = - omap_mcbsp_set_threshold; - /* TODO: Currently, MODE_ELEMENT == MODE_FRAME */ - if (omap_mcbsp_get_dma_op_mode(bus_id) == - MCBSP_DMA_MODE_THRESHOLD) - sync_mode = OMAP_DMA_SYNC_FRAME; } else { return -ENODEV; } - omap_mcbsp_dai_dma_params[id][substream->stream].name = - substream->stream ? "Audio Capture" : "Audio Playback"; - omap_mcbsp_dai_dma_params[id][substream->stream].dma_req = dma; - omap_mcbsp_dai_dma_params[id][substream->stream].port_addr = port; - omap_mcbsp_dai_dma_params[id][substream->stream].sync_mode = sync_mode; switch (params_format(params)) { case SNDRV_PCM_FORMAT_S16_LE: - omap_mcbsp_dai_dma_params[id][substream->stream].data_type = - OMAP_DMA_DATA_TYPE_S16; + dma_data->data_type = OMAP_DMA_DATA_TYPE_S16; + wlen = 16; break; case SNDRV_PCM_FORMAT_S32_LE: - omap_mcbsp_dai_dma_params[id][substream->stream].data_type = - OMAP_DMA_DATA_TYPE_S32; + dma_data->data_type = OMAP_DMA_DATA_TYPE_S32; + wlen = 32; break; default: return -EINVAL; } + if (cpu_is_omap343x()) { + dma_data->set_threshold = omap_mcbsp_set_threshold; + /* TODO: Currently, MODE_ELEMENT == MODE_FRAME */ + if (omap_mcbsp_get_dma_op_mode(bus_id) == + MCBSP_DMA_MODE_THRESHOLD) { + int period_words, max_thrsh; + + period_words = params_period_bytes(params) / (wlen / 8); + if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK) + max_thrsh = omap_mcbsp_get_max_tx_threshold( + mcbsp_data->bus_id); + else + max_thrsh = omap_mcbsp_get_max_rx_threshold( + mcbsp_data->bus_id); + /* + * If the period contains less or equal number of words, + * we are using the original threshold mode setup: + * McBSP threshold = sDMA frame size = period_size + * Otherwise we switch to sDMA packet mode: + * McBSP threshold = sDMA packet size + * sDMA frame size = period size + */ + if (period_words > max_thrsh) { + int divider = 0; + + /* + * Look for the biggest threshold value, which + * divides the period size evenly. + */ + divider = period_words / max_thrsh; + if (period_words % max_thrsh) + divider++; + while (period_words % divider && + divider < period_words) + divider++; + if (divider == period_words) + return -EINVAL; + + pkt_size = period_words / divider; + sync_mode = OMAP_DMA_SYNC_PACKET; + } else { + sync_mode = OMAP_DMA_SYNC_FRAME; + } + } + } + + dma_data->name = substream->stream ? "Audio Capture" : "Audio Playback"; + dma_data->dma_req = dma; + dma_data->port_addr = port; + dma_data->sync_mode = sync_mode; + dma_data->packet_size = pkt_size; - snd_soc_dai_set_dma_data(cpu_dai, substream, - &omap_mcbsp_dai_dma_params[id][substream->stream]); + snd_soc_dai_set_dma_data(cpu_dai, substream, dma_data); if (mcbsp_data->configured) { /* McBSP already configured by another stream */ @@ -419,7 +436,6 @@ static int omap_mcbsp_dai_hw_params(struct snd_pcm_substream *substream, switch (params_format(params)) { case SNDRV_PCM_FORMAT_S16_LE: /* Set word lengths */ - wlen = 16; regs->rcr2 |= RWDLEN2(OMAP_MCBSP_WORD_16); regs->rcr1 |= RWDLEN1(OMAP_MCBSP_WORD_16); regs->xcr2 |= XWDLEN2(OMAP_MCBSP_WORD_16); @@ -427,7 +443,6 @@ static int omap_mcbsp_dai_hw_params(struct snd_pcm_substream *substream, break; case SNDRV_PCM_FORMAT_S32_LE: /* Set word lengths */ - wlen = 32; regs->rcr2 |= RWDLEN2(OMAP_MCBSP_WORD_32); regs->rcr1 |= RWDLEN1(OMAP_MCBSP_WORD_32); regs->xcr2 |= XWDLEN2(OMAP_MCBSP_WORD_32); |