1 files changed, 260 insertions, 0 deletions
diff --git a/tools/testing/ktest/examples/crosstests.conf b/tools/testing/ktest/examples/crosstests.conf
new file mode 100644
index 0000000..4673660
--- /dev/null
+++ b/tools/testing/ktest/examples/crosstests.conf
@@ -0,0 +1,260 @@
+#
+# Example config for cross compiling
+#
+# In this config, it is expected that the tool chains from:
+#
+#   http://kernel.org/pub/tools/crosstool/files/bin/x86_64/
+#
+# running on a x86_64 system have been downloaded and installed into:
+#
+#   /usr/local/
+#
+# such that the compiler binaries are something like:
+#
+#   /usr/local/gcc-4.5.2-nolibc/mips-linux/bin/mips-linux-gcc
+#
+# Some of the archs will use gcc-4.5.1 instead of gcc-4.5.2
+# this config uses variables to differentiate them.
+# 
+# Comments describe some of the options, but full descriptions of
+# options are described in the samples.conf file.
+
+# ${PWD} is defined by ktest.pl to be the directory that the user
+# was in when they executed ktest.pl. It may be better to hardcode the
+# path name here. THIS_DIR is the variable used through out the config file
+# in case you want to change it.
+
+THIS_DIR := ${PWD}
+
+# Update the BUILD_DIR option to the location of your git repo you want to test.
+BUILD_DIR = ${THIS_DIR}/linux.git
+
+# The build will go into this directory. It will be created when you run the test.
+OUTPUT_DIR = ${THIS_DIR}/cross-compile
+
+# The build will be compiled with -j8
+BUILD_OPTIONS = -j8
+
+# The test will not stop when it hits a failure.
+DIE_ON_FAILURE = 0
+
+# If you want to have ktest.pl store the failure somewhere, uncomment this option
+# and change the directory where ktest should store the failures.
+#STORE_FAILURES = ${THIS_DIR}/failures
+
+# The log file is stored in the OUTPUT_DIR called cross.log
+# If you enable this, you need to create the OUTPUT_DIR. It wont be created for you.
+LOG_FILE = ${OUTPUT_DIR}/cross.log
+
+# The log file will be cleared each time you run ktest.
+CLEAR_LOG = 1
+
+# As some archs do not build with the defconfig, they have been marked
+# to be ignored. If you want to test them anyway, change DO_FAILED to 1.
+# If a test that has been marked as DO_FAILED passes, then you should change
+# that test to be DO_DEFAULT
+
+DO_FAILED := 0
+DO_DEFAULT := 1
+
+# By setting both DO_FAILED and DO_DEFAULT to zero, you can pick a single
+# arch that you want to test. (uncomment RUN and chose your arch)
+#RUN := m32r
+
+# At the bottom of the config file exists a bisect test. You can update that
+# test and set DO_FAILED and DO_DEFAULT to zero, and uncomment this variable
+# to run the bisect on the arch.
+#RUN := bisect
+
+# By default all tests will be running gcc 4.5.2. Some tests are using 4.5.1
+# and they select that in the test.
+# Note: GCC_VER is declared as on option and not a variable ('=' instead of ':=')
+# This is important. A variable is used only in the config file and if it is set
+# it stays that way for the rest of the config file until it is change again.
+# Here we want GCC_VER to remain persistent and change for each test, as it is used in
+# the MAKE_CMD. By using '=' instead of ':=' we achieve our goal.
+
+GCC_VER = 4.5.2
+MAKE_CMD = PATH=/usr/local/gcc-${GCC_VER}-nolibc/${CROSS}/bin:$PATH CROSS_COMPILE=${CROSS}- make ARCH=${ARCH}
+
+# all tests are only doing builds.
+TEST_TYPE = build
+
+# If you want to add configs on top of the defconfig, you can add those configs into
+# the add-config file and uncomment this option. This is useful if you want to test
+# all cross compiles with PREEMPT set, or TRACING on, etc.
+#ADD_CONFIG = ${THIS_DIR}/add-config
+
+# All tests are using defconfig
+BUILD_TYPE = defconfig
+
+# The test names will have the arch and cross compiler used. This will be shown in
+# the results.
+TEST_NAME = ${ARCH} ${CROSS}
+
+# alpha
+TEST_START IF ${RUN} == alpha || ${DO_DEFAULT}
+# Notice that CROSS and ARCH are also options and not variables (again '=' instead
+# of ':='). This is because TEST_NAME and MAKE_CMD wil use them for each test.
+# Only options are available during runs. Variables are only present in parsing the
+# config file.
+CROSS = alpha-linux
+ARCH = alpha
+
+# arm
+TEST_START IF ${RUN} == arm || ${DO_DEFAULT}
+CROSS = arm-unknown-linux-gnueabi
+ARCH = arm
+
+# black fin
+TEST_START IF ${RUN} == bfin || ${DO_DEFAULT}
+CROSS = bfin-uclinux
+ARCH = blackfin
+BUILD_OPTIONS = -j8 vmlinux
+
+# cris - FAILS?
+TEST_START IF ${RUN} == cris || ${RUN} == cris64 || ${DO_FAILED}
+CROSS = cris-linux
+ARCH = cris
+
+# cris32 - not right arch?
+TEST_START IF ${RUN} == cris || ${RUN} == cris32 || ${DO_FAILED}
+CROSS = crisv32-linux
+ARCH = cris
+
+# ia64
+TEST_START IF ${RUN} == ia64 || ${DO_DEFAULT}
+CROSS = ia64-linux
+ARCH = ia64
+
+# frv
+TEST_START IF ${RUN} == frv || ${DO_FAILED}
+CROSS = frv-linux
+ARCH = frv
+GCC_VER = 4.5.1
+
+# h8300 - failed make defconfig??
+TEST_START IF ${RUN} == h8300 || ${DO_FAILED}
+CROSS = h8300-elf
+ARCH = h8300
+GCC_VER = 4.5.1
+
+# m68k fails with error?
+TEST_START IF ${RUN} == m68k || ${DO_DEFAULT}
+CROSS = m68k-linux
+ARCH = m68k
+
+# mips64
+TEST_START IF ${RUN} == mips || ${RUN} == mips64 || ${DO_DEFAULT}
+CROSS = mips64-linux
+ARCH = mips
+
+# mips32
+TEST_START IF ${RUN} == mips || ${RUN} == mips32 || ${DO_DEFAULT}
+CROSS = mips-linux
+ARCH = mips
+
+# m32r
+TEST_START IF ${RUN} == m32r || ${DO_FAILED}
+CROSS = m32r-linux
+ARCH = m32r
+GCC_VER = 4.5.1
+BUILD_OPTIONS = -j8 vmlinux
+
+# parisc64 failed?
+TEST_START IF ${RUN} == hppa || ${RUN} == hppa64 || ${DO_FAILED}
+CROSS = hppa64-linux
+ARCH = parisc
+
+# parisc
+TEST_START IF ${RUN} == hppa || ${RUN} == hppa32 || ${DO_FAILED}
+CROSS = hppa-linux
+ARCH = parisc
+
+# ppc
+TEST_START IF ${RUN} == ppc || ${RUN} == ppc32 || ${DO_DEFAULT}
+CROSS = powerpc-linux
+ARCH = powerpc
+
+# ppc64
+TEST_START IF ${RUN} == ppc || ${RUN} == ppc64 || ${DO_DEFAULT}
+CROSS = powerpc64-linux
+ARCH = powerpc
+
+# s390
+TEST_START IF ${RUN} == s390 || ${DO_DEFAULT}
+CROSS = s390x-linux
+ARCH = s390
+
+# sh
+TEST_START IF ${RUN} == sh || ${DO_DEFAULT}
+CROSS = sh4-linux
+ARCH = sh
+
+# sparc64
+TEST_START IF ${RUN} == sparc || ${RUN} == sparc64 || ${DO_DEFAULT}
+CROSS = sparc64-linux
+ARCH = sparc64
+
+# sparc
+TEST_START IF ${RUN} == sparc || ${RUN} == sparc32 || ${DO_DEFAULT}
+CROSS = sparc-linux
+ARCH = sparc
+
+# xtensa failed
+TEST_START IF ${RUN} == xtensa || ${DO_FAILED}
+CROSS = xtensa-linux
+ARCH = xtensa
+
+# UML
+TEST_START IF ${RUN} == uml || ${DO_DEFAULT}
+MAKE_CMD = make ARCH=um SUBARCH=x86_64
+ARCH = uml
+CROSS =
+
+TEST_START IF ${RUN} == x86 || ${RUN} == i386 || ${DO_DEFAULT}
+MAKE_CMD = make ARCH=i386
+ARCH = i386
+CROSS = 
+
+TEST_START IF ${RUN} == x86 || ${RUN} == x86_64 || ${DO_DEFAULT}
+MAKE_CMD = make ARCH=x86_64
+ARCH = x86_64
+CROSS = 
+
+#################################
+
+# This is a bisect if needed. You need to give it a MIN_CONFIG that
+# will be the config file it uses. Basically, just copy the created defconfig
+# for the arch someplace and point MIN_CONFIG to it.
+TEST_START IF ${RUN} == bisect
+MIN_CONFIG = ${THIS_DIR}/min-config
+CROSS = s390x-linux
+ARCH = s390
+TEST_TYPE = bisect
+BISECT_TYPE = build
+BISECT_GOOD = v3.1
+BISECT_BAD = v3.2
+CHECKOUT = v3.2
+
+#################################
+
+# These defaults are needed to keep ktest.pl from complaining. They are
+# ignored because the test does not go pass the build. No install or
+# booting of the target images.
+
+DEFAULTS
+MACHINE = crosstest
+SSH_USER = root
+BUILD_TARGET = cross
+TARGET_IMAGE = image
+POWER_CYCLE = cycle
+CONSOLE = console
+LOCALVERSION = version
+GRUB_MENU = grub
+
+REBOOT_ON_ERROR = 0
+POWEROFF_ON_ERROR = 0
+POWEROFF_ON_SUCCESS = 0
+REBOOT_ON_SUCCESS = 0
+