| Age | Commit message (Collapse) | Author |
|---|
|
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
SFC4000 boards also have an EEPROM exposed as MTD.
The boot configuration is accessed through MTD.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
The SFC9000-family controllers have firmware to manage all board
peripherals including temperature, heat sink continuity and voltage
sensors. The firmware reports sensor alarms, which we log, and
will shut down the board if necessary.
Some users may want to monitor their boards more closely, so add an
hwmon driver that exposes all sensors reported by the firmware. Move
efx_mcdi_sensor_event() into the new file so it can share the array of
sensor labels with the hwmon driver.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
Interrupts are normally generated by the event queues, moderated by
timers. However, they may also be triggered by detection of a 'fatal'
error condition (e.g. memory parity error) or by the host writing to
certain CSR fields as part of a self-test.
The IRQ level/index used for these on Falcon rev B0 and Siena is set
by the KER_INT_LEVE_SEL field and cached by the driver in
efx_nic::fatal_irq_level. Since this value is also relevant to
self-tests rename the field to just 'irq_level'.
Avoid unnecessary cache traffic by using a per-channel 'last_irq_cpu'
field and only writing to the per-controller field when the interrupt
matches efx_nic::irq_level. Remove the volatile qualifier and use
ACCESS_ONCE in the places we read these fields.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
This reverts commit 6369545945b90daa1a73fca174da9194c398417c in
drivers/net/ethernet/sfc/falcon.c.
Unlike the INT_ISR0 register on later controller revisions, the
NET_IVEC_INT_Q bits written to memory are only ever set for
interrupting event queues, not for any other interrupt sources.
By definition there can only be one legacy interrupt handler per
function, so there is no need to worry about detecting a fatal
interrupt more than once.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
We cannot safely assume that the NAPI handler will complete within the
20 ms that we allow for the event self-test. The handler may be
deferred for longer than this, particularly on realtime kernels.
Instead, check whether either an event has been handled or (as in the
old failure path) whether an interrupt has been received and an event
has been delivered but not yet handled. Use napi_disable() to
synchronize with the NAPI handler before checking, since it will
clear events before updating eventq_read_ptr.
Remove the test result chan.N.eventq.poll, since it is not an error
if the NAPI handler does not run during the test.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
We currently assume that the timer quantum for Siena is 5 us, the same
as for Falcon. This is not correct; timer ticks are generated on a
rota which takes a minimum of 768 cycles (each event delivery or other
timer change will delay it by 3 cycles). The timer quantum should be
6.144 or 3.072 us depending on whether turbo mode is active.
Replace EFX_IRQ_MOD_RESOLUTION with a timer_quantum_ns field in struct
efx_nic, initialised by the efx_nic_type::probe function.
While we're at it, replace EFX_IRQ_MOD_MAX with a timer_period_max
field in struct efx_nic_type.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
The netif_dbg() macro is defined in <linux/netdevice.h>. If the DEBUG
macro is defined, it logs a message at 'debug' level, otherwise it
does nothing.
In net_driver.h we define DEBUG if EFX_ENABLE_DEBUG is defined, but
this is too late for those source files that already got a
definition of netif_dbg() by including <linux/netdevice.h>
Get rid of EFX_ENABLE_DEBUG, and only define and test DEBUG.
In mtd.c, we do not use DEBUG as a condition flag but are forced to
use the DEBUG macro-function from <linux/mtd/mtd.h>. Undefine DEBUG
before including it.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
Both implementations of efx_nic_type::reconfigure_mac operation
push the multicast hash filter to the hardware. It is therefore
redundant to call efx_nic_type::push_multicast_hash as well.
efx_mcdi_mac_reconfigure() also uses this operation, but the
implementation for Siena just uses MCDI anyway. Merge that into
efx_mcdi_mac_reconfigure().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
The latter is only called by the former, which is a very short
wrapper. Further, gcc 4.5 may currently wrongly warn that the
'faults' variable may be used uninitialised.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
No NICs need to switch efx_mac_operations at run-time, and the MAC
operations are fairly closely bound to NIC types.
Move efx_mac_operations::reconfigure to efx_nic_type::reconfigure_mac
and efx_mac_operations::check_fault fo efx_nic_type::check_mac_fault.
Change callers to call through efx->type or directly if the NIC type
is known.
Remove efx_mac_operations::update_stats. The implementations for
Falcon used to fetch MAC statistics synchronously and this was used by
efx_register_netdev() to clear statistics after running self-tests.
However, it now only converts statistics that have already been
fetched (and that only for Falcon), and the call from
efx_register_netdev() has no effect.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
efx_nic::stats_lock is used to serialise stats updates, but each
reader was dropping it before it finished reading efx_nic::mac_stats.
If there were concurrent stats reads using procfs, or one using procfs
and one using ethtool, an update could race with a read. On a 32-bit
system, the reader could see word-tearing of 64-bit stats (32 bits of
the old value and 32 bits of the new).
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
These are defined alongside the firmware protocol in mcdi_pcol.h.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
When the MC reboots, either as part of a firmware upgrade or due to a
bug, it attempts to complete (with an error) any requests that were
outstanding before the reboot. Since there is an inherent race
condition in checking this, it will also write to a status word in
shared memory.
If we look at each of these separately, we may detect each reboot
twice, resulting in a spurious command failure after a firmware
upgrade or frustrating recovery from a firmware bug. Instead, if a
request completion indicates a reboot, we must poll and clear the
status word.
This bug was previously masked by use of an incorrect address for the
status word. Fix that, using the definition now included in
mcdi_pcol.h.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
By the time we look at the MAC address in efx_probe_port(), either the
driver or the firmware has already validated the board configuration.
The possibility of having an invalid MAC address just isn't worth
considering. It certainly isn't worth having a compile-time option
for this.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
Suggested by YOSHIFUJI Hideaki.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Otherwise (on sparc64):
drivers/net/ethernet/intel/e1000e/ethtool.c:657:3: error: implicit declaration of function 'vmalloc' [-Werror=implicit-function-declaration]
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The only semantic difference is that we now hold a reference to the
neighbour and thus have to release it.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the future the ipv4/ipv6 route gateway will take on two types
of values:
1) INADDR_ANY/IN6ADDR_ANY, for local network routes, and in this case
the neighbour must be obtained using the destination address in
ipv4/ipv6 header as the lookup key.
2) Everything else, the actual nexthop route address.
So if the gateway is not inaddr-any we use it, otherwise we must use
the packet's destination address.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It might be useful to get a counter of failed tcp_retransmit_skb()
calls.
Reported-by: Satoru Moriya <satoru.moriya@hds.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allocation of 64 bytes in skb headroom is not enough if we have to pull
ethernet + ipv6 + tcp headers, and/or extra tunneling header.
Its currently not noticed because netdev_alloc_skb_ip_align(64) give us
more room, thanks to power-of-two kmalloc() roundups.
Make sure we ask for 128 bytes so that side effects of upcoming patches
from Ian Campbell dont decrease benet rx performance, because of extra
skb head reallocations.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ian Campbell <Ian.Campbell@citrix.com>
Cc: Vasundhara Volam <vasundhara.volam@emulex.com>
Cc: Sathya Perla <sathya.perla@emulex.com>
Cc: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add statistics for tracking parity errors from which we successfully
recovered and those which were deemed unrecoverable.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
1. Sample mcp pulse and mcp sequence in nic load instead of in init_one
as they may change by the time we want to use them.
2. Allow cnic to access device during nic load (by adding a new "LOADING" state
to recovery flow). This prevents the unnecessary cnic timeout which resulted
by cnic attempting to access because nic is loading, but being blocked because
of the Recovery state.
3. Issue 'fake' driver load command to mcp when last driver unloads to prevent
mcp from taking ownership. When recovery is complete unload fake driver to
allow mcp to initialize the hardware before first driver loads.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The recovery register (to which a hardware lock has been added in previous
patch) is used amongst other things to track the active PFs. The old
implementation which used a per path counter is not viable in a virtualized
environment where a pf may increment the counter and then have the kernel
crash around it preventing the counter from ever reaching zero.
In the new implementation the scenario described will result in the PF timing
out against the mcp, which will clear the PF's bit in the bitmask allowing
recovery process to proceed.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use hardware locks to protect resources common to several Physical Functions. In
a virtualized environment the RTNL lock only protects a PF's driver against
the PFs sharing it's VMs with regard to device resources. Other PFs may reside
in other VMs under other OSs, and are not subject to the lock. Such resources
which were previously protected implicitly by the RTNL lock must now be
protected explicitly with dedicated HW locks.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In a virtualized environment it is possible for a loading driver to discover
that Firmware is already loaded to the device, and that this FW does not match
its own. This can happen for example if different Physical Functions are
Assigned to different VMs in which different driver versions are loaded. The
code in this patch ensures that only drivers with matching FW are loaded over
the device, and that in the case described above where the Firmware version
doesn't match the driver load is aborted.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
1. Fix bug where return value is ignored
2. Improve printouts
3. Fix typos
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
BDF was obtained from kernel but since in virtualized environment
(e.g. physical device assigment in KVM) the function number may
not be the real one, the info must be obtained from the device.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In virtualized environments indirect access to the device may not be supported
(depending on the Hypervisor type). Indirect device access was used since in
some harware contexts (i.e. certain chipset and BIOS) every access the driver
makes across the pci is followed by a BIOS initiated Zero Length Read to the
same address. When accessing widebus registers this zero length read corrupts
the serialization of the read/write sequence resulting with errors. To avoid
this problem widebus registers are always accessed via the DMAE or the indirect
interface. However, the 57712x and 578xx devices intercept the zero length read
and so using the indirect interface with these devices is not necessary. Since
PDA is only supported for 57712x and 578xx the indirect access to device was
restricted to 57710 and 57711x.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Enable the use of up to three hardware queues for transmission. The queues
are always dequed round robin (i.e. strict priority, PFC and ETS are not
supported). This does allow the allocation of a seperate HW queue for low
volume, high priority traffic which will be serviced more promptly.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On 82574/82583, there is a hardware bug which might cause a Tx hang when
the internal buffer is full. Setting this bit enables a hardware fix to
work around the issue.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This code snippet is simply writing default values to the register which is
unnecessary since the values are programmed into the register by default.
There is a special case for 80003es2lan needing the Retransmit on Late
Collision bit set but that is also done in e1000_init_hw_80003es2lan().
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Use the default hardware values for TIPG except for 80003es2lan(*). The
code that is removed in this patch is either unnecessarily writing the TIPG
register with the hardware default values for some devices (82571/2/3/4) or
writing the wrong value for others (ICH/PCH LOMs). The only change in
functionality is setting the correct default TIPG for the latter devices.
(*) The correct value for 80003es2lan is already set properly in
e1000_init_hw_80003es2lan() and e1000_cfg_kmrn_{10_100|1000}_80003es2lan(),
and the unused flag FLAG_TIPG_MEDIUM_FOR_80003ESLAN is removed.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When connected to certain switches, the 82579 PHY might drop link
unexpectedly. Work around the issue by setting the Mean Square Error
higher than the hardware default.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The hardware erratum workaround where the TXDCTL register must be the same
setting for both queues should always be done.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Based on a patch from Prabhakar Kushwaha <prabhakar@freescale.com>, set
appropriate default interrupt mode dependent on whether CONFIG_PCI_MSI
is enabled in the kernel configuration and if the hardware supports
MSI-X. Set the module parameter log message accordingly.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Cc: Jin Qing <b24347@freescale.com>
Cc: Prabhakar Kushwaha <prabhakar@freescale.com>
Cc: Jin Qing <b24347@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Make it more like how igb does it, with some additional error checking.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
For ring-specific functions, pass a pointer to the ring struct instead of a
pointer to the adapter struct.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The Tx/Rx head and tail registers and itr_register are always at known
addresses based on the __iomem address at which the PCI region (from BAR 0)
is mapped and known offsets within the region for each of these registers.
Store and use the full address rather than just the region offset to reduce
unnecessary address calculations. Also, change current u8 __iomem pointers
to void __iomem pointers.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Enable RPS by default. Disallow jumbo frames when both receive checksum
and receive hashing are enabled because the hardware cannot do both IP
payload checksum (enabled when receive checksum is enabled when using
packet split which is used for jumbo frames) and provide RSS hash at the
same time.
v2: added ethtool command to query flow hashing behavior per Ben Hutchings
and changed the type of rsskey to cleanup the setting of the register
array and avoid unnecessary casts (as pointed out by Joe Perches).
The long error messages are not changed since there is nothing in
the kernel ./Documentation that suggests the preferred method for
dealing with long messages other than to never break strings; leaving
them as-is for now.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
1) cleanup whitespace in e1000_rx_checksum() function header comment
2) do not check hardware checksum when Rx checksum is disabled
3) reduce duplicated calls to le16_to_cpu() by just using it within
e1000_rx_checksum() instead of in each call to the function
v2: use swab16 instead of le16_to_cpu & htons and corrected type for the
passed-in csum
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Now we must provide the IP destination address, and a reference has
to be dropped when we're done with the entry.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now we must provide the IP destination address, and a reference has
to be dropped when we're done with the entry.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now we must provide the IP destination address, and a reference has
to be dropped when we're done with the entry.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some WWAN LTE/3G devices based on chipsets from Qualcomm provide
near standard CDC ECM interfaces in addition to the usual serial
interfaces. The Huawei E392/E398 are examples of such devices.
These typically cannot be fully configured using AT commands
over a serial interface. It is necessary to speak the proprietary
Qualcomm MSM Interface (QMI) protocol to the device to enable the
ethernet proxy functionality.
The devices embed the QMI protocol in CDC on the control interface,
using standard CDC commands and notifications. The do not otherwise
use CDC commands for the ethernet function. This driver does
therefore not need access to any other aspects of the control
interface than the descriptors attached to it.
Another driver, cdc-wdm, will provide userspace access to the
QMI protocol independently of this driver. To facilitate this,
this driver avoids binding to the control interface, and uses
only the associated data interface after parsing the common CDC
functional descriptors on the control interface.
You will want both the cdc-wdm and option drivers as companions to
this driver, to have full access to all interfaces and protocols
exported by the device.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This driver adds support for Xilinx 10/100/1000 AXI Ethernet.
It can be used, for instance, on Xilinx boards with a Microblaze
architecture like the ML605.
The patch is against the latest net-next tree and checkpatch clean.
Signed-off-by: Ariane Keller <ariane.keller@tik.ee.ethz.ch>
Signed-off-by: Daniel Borkmann <daniel.borkmann@tik.ee.ethz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We introduced a new return here but forgot to drop the lock.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
