| Age | Commit message (Collapse) | Author |
|---|
|
For ARMv7 kernels running in the non-secure world, writing to the
auxillary control register causes an abort, so we must avoid directly
writing the auxillary control register. If the ACR has already been
reinitialized by SoC code, don't try to restore it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Add a dsb after the isb to ensure that the previous writes to the
CP15 registers take effect before we enable the MMU.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
ARM920 and ARM926 save four registers, not three. Fix the size of
the suspend region required.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
r1 stores the v:p offset from the CPU invariant resume code, and is
expected to be preserved by the CPU specific code. Overwriting it is
not a good idea.
We've managed to get away with it on sa1100 platforms because most
happen to have PHYS_OFFSET == PAGE_OFFSET, but that may not be the
case depending on kernel configuration. So fix this latent bug.
This fixes xsc3 as well which was saving and restoring this register
independently.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
cpu_v7_reset disables the MMU and then branches to the provided address.
On Thumb-2 kernels, we should take care to clear the Thumb Exception
enable bit in the System Control Register, otherwise this may wreak
havok in the code to which we are branching (for example, an ARM kernel
image via kexec).
Reviewed-by: Dave Martin <dave.martin@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Commit 540b5738 ("ARM: 6999/1: head, zImage: Always Enter the kernel in
ARM state") mandates that the kernel should be entered in ARM state.
If a Thumb-2 kernel kexecs a new kernel image, we need to ensure that
we change state when branching to the new code. This patch replaces a
mov pc, lr with a bx lr on Thumb-2 kernels so that we transition to ARM
state if need be.
Reviewed-by: Dave Martin <dave.martin@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This patch updates the recently submitted
"Associate the HDMI clock together with LCDC1 on sh7372"
to V2 with the following change:
- Use lcdc1_device on AP4EVB to build properly.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
The nfsservctl system call is now gone, so we should remove all
linkage for it.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git+ssh://master.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc into fixes
|
|
|
|
This patch fixes following building error:
--
arch/arm/mach-footbridge/dc21285.c: In function 'dc21285_preinit':
arch/arm/mach-footbridge/dc21285.c:299:2: error: 'vga_base' undeclared (first use in this function)
arch/arm/mach-footbridge/dc21285.c:299:2: note: each undeclared identifier is reported only once for each function it appears in
make[1]: *** [arch/arm/mach-footbridge/dc21285.o] Error 1
--
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
|
|
This patch fixed following building error:
--
arch/arm/mach-orion5x/pci.c: In function 'orion5x_pci_sys_setup':
arch/arm/mach-orion5x/pci.c:563:2: error: 'vga_base' undeclared (first use in this function)
arch/arm/mach-orion5x/pci.c:563:2: note: each undeclared identifier is reported only once for each function it appears in
make[1]: *** [arch/arm/mach-orion5x/pci.o] Error 1
make[1]: *** Waiting for unfinished jobs....
--
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
|
|
Upstream commit d5341942d784134f2997b3ff82cd63cf71d1f932 "PCI: Make the
struct pci_dev * argument of pci_fixup_irqs const." leaked an extra
"const" into an actual call site (vs a proto/decl) which causes this:
arch/arm/mach-orion5x/dns323-setup.c: In function 'dns323_pci_map_irq':
arch/arm/mach-orion5x/dns323-setup.c:80: error: expected expression before 'const'
arch/arm/mach-orion5x/dns323-setup.c:80: error: too few arguments to function 'orion5x_pci_map_irq'
make[3]: *** [arch/arm/mach-orion5x/dns323-setup.o] Error 1
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Commit c03f007a8bf0e092caeb6856a5c8a850df10b974 (OMAP: PM:
omap_device: add system PM methods for PM domain handling) mistakenly
used SET_SYSTEM_SLEEP_PM_OPS() when trying to configure custom methods
for the PM domains noirq methods. Fix that by setting only the
suspend_noirq and resume_noirq methods with custom versions.
Note that all other PM domain methods (including the "normal"
suspend/resume methods) are populated using USE_PLATFORM_PM_SLEEP_OPS,
which configures them all to the default subsystem (platform_bus)
methods.
Reported-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
Associate the HDMI clock together with LCDC1 on sh7372.
Without this patch Suspend-to-RAM hangs on the boards
AP4EVB and Mackerel. The code hangs in the LCDC driver
where the software is waiting forever for the hardware to
power down. By explicitly associating the HDMI clock with
LCDC1 we can make sure the HDMI clock is enabled using
Runtime PM whenever the driver is accessing the hardware.
This HDMI and LCDC1 dependency is documented in the sh7372
data sheet. Older kernels did work as expected but the
recently merged (3.1-rc)
794d78f drivers: sh: late disabling of clocks V2
introduced code to turn off clocks lacking software reference
which happens to include the HDMI clock that is needed by
LCDC1 to operate as expected.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
This was a typo in clockdev declaration for at91sam9261 SoC.
Fix the kernel hanging when switching clocksource to TC (tcb_clksrc).
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Remy Bohmer <linux@bohmer.net>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
It seems that an entry for the SP805 watchdog in the table of clocks was
missing. This results in the sp805_wdt driver rejecting the device with
the following errors:
sp805-wdt mb:wdt: Clock not found
sp805-wdt mb:wdt: Probe Failed!!!
sp805-wdt: probe of mb:wdt failed with error -2
While not obviously stated in the hardware docs, the onboard SP810's
"REFCLK" is connected to a 32.768KHz crystal, and this drives the
watchdog. Add a struct clk and corresponding lookup entry for it.
Signed-off-by: Nick Bowler <nbowler@elliptictech.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The oscillator that supplies GPT12_FCLK and WDT1_FCLK exists in the
WKUP powerdomain[1]. This resolves at least one boot-time warning:
omap_hwmod: gpt12_fck: missing clockdomain for gpt12_fck.
1. _OMAP34xx Multimedia High Security (HS) Device Silicon Revision 3.1.x
Security Addendum Version K (SWPU119K)_ Figure 3-29. August 2010.
|
|
I made some changes to the entry in the ARM Machine Registry after
submission which was the wrong thing to do.
This patch should help to fix this error.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Fix the following compile warning:
arch/arm/mach-omap2/clock44xx_data.c: In function 'omap4xxx_clk_init':
arch/arm/mach-omap2/clock44xx_data.c:3371:6: warning: 'cpu_clkflg' may be used uninitialized in this function
The approach taken here is intended to work if omap4xxx_clk_init() is
converted into an initcall.
Thanks to Bjarne Steinsbo <bsteinsbo@gmail.com> for proposing another
approach.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Bjarne Steinsbo <bsteinsbo@gmail.com>
|
|
After commit 665d001338b494d6d62810aa99b4c0fa1a0884b9 ("OMAP2+: hwmod:
Follow the recommended PRCM module enable sequence"), device drivers
for OMAP IP blocks that do not use runtime PM can cause oopses or
kernel instability[1][2].
This is because those non-runtime PM drivers do not use the hwmod
code, which implements the correct IP block enable and disable
sequence.
Several options for dealing with this problem have been proposed:
1. Add a new field to the OMAP struct clk to mark clocks that are
currently used by non-runtime PM drivers. Modify the clock code to
use the old clockdomain sequence for these marked clocks. As
drivers are converted to use runtime PM, remove the annotation from
the clocks.
2. Similar to #1, but associate the flag with the struct omap_clk
instead.
3. Add IDLEST wait support to the OMAP4 clock code, similar to the way
it is implemented for OMAP2/3, and enable it in each struct clk
currently used by non-runtime PM drivers. As drivers are converted
to use runtime PM, remove the annotation from the clocks.
4. Do nothing; leave the problem to those responsible for the
unconverted drivers.
5. Re-enable clock-based clockdomain control in the OMAP4 clock code.
This would revert back to the behavior of Linux 3.0, simply with a
slightly longer module enable/disable latency.
Unfortunately, no approach seemed particularly good. Options 1
through 3 seemed unwise due to the following reasons:
A. The OMAP struct clks are intended primarily to describe hardware
clock nodes, and the intention is that no driver-specific data
should be stored there (applies to #1)
B. The resulting patch would have been quite large for the -rc series
(applies to #1, #2, #3)
C. The patch would have been a new, yet temporary hack; and similar fixes
have drawn negative comments in the recent past (see for example [3])
Option 4 is undesirable because commit
665d001338b494d6d62810aa99b4c0fa1a0884b9 ("OMAP2+: hwmod: Follow the
recommended PRCM module enable sequence") has resulted in a less
stable kernel; and kernel stability is more important than OMAP4 power
management.
Option 5 is the approach taken in this patch. This seemed to be the
least intrusive approach for 3.1-rc.
The approach in this patch was originally proposed by Ohad Ben-Cohen
<ohad@wizery.com>. I'm simply writing the commit message and passing
it along.
...
Thanks to Luciano Coelho <coelho@ti.com> for reporting the problem.
Thanks to Ohad Ben-Cohen <ohad@wizery.com> for tracking the problem
down, generating a temporary workaround, and proposing a patch to deal
with the problem. Thanks to Rajendra Nayak <rnayak@ti.com> for
proposing another patch to deal with the problem. Thanks to Felipe
Balbi <balbi@ti.com> for comments.
1. Coelho, Luciano <coelho@ti.com>. _Re: Oops on ehci_hcd when
booting 3.0.0-rc2 on panda_. Tue, 09 Aug 2011 14:26:08 +0300.
Posted to the <linux-omap@vger.kernel.org> mailing list. Available
from (among others)
http://www.spinics.net/linux/lists/linux-omap/msg55213.html
2. Munegowda, Keshava <keshava_mgowda@ti.com>. _Re: Oops on ehci_hcd
when booting 3.0.0-rc2 on panda_. Thu, 11 Aug 2011 13:51:05 +0530.
Posted to the <linux-omap@vger.kernel.org> mailing list. Available
from (among others)
http://www.spinics.net/linux/lists/linux-omap/msg55371.html
3. King, Russell <linux@arm.linux.org.uk>. _Re: [PATCH 5/8] OMAP4:
PM: TEMP: Prevent l3init from idling/force sleep_. Thu, 23 Jun
2011 16:22:49 +0100. Posted to the <linux-omap@vger.kernel.org>
mailing list. Available from (among others)
http://www.mail-archive.com/linux-omap@vger.kernel.org/msg51392.html
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Luciano Coelho <coelho@ti.com>
Cc: Ohad Ben-Cohen <ohad@wizery.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
|
|
force wakeup
While using clockdomain force wakeup method, not waiting for powerdomain
to be effectively ON may end up locking the clockdomain FSM until a
next wakeup event occurs.
One such issue was seen on OMAP4430, where L4_PER was periodically
getting stuck in in-transition state when transitioning from from OSWR to ON.
This issue was reported and investigated by Patrick Titiano <p-titiano@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Reported-by: Patrick Titiano <p-titiano@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
[paul@pwsan.com: updated to apply; added transition wait on clkdm_deny_idle();
remove two superfluous pwrdm_wait_transition() calls]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
Program all powerdomain target state as ON; this is to prevent domains
from hitting low power states (if bootloader has target states set to
something other than ON) and potentially even losing context while PM
is not fully initialized, which can cause the system to crash. The PM
late init code can then program the desired target state for all the
power domains.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
[paul@pwsan.com: dropped comment typo hunk; fixed comment indent and moved
to kerneldoc; moved code to pwrdm_init(); changed pwrdm_init() argument name
to prevent clash; cleaned up patch description]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
Should be passing the parent clk object when
calling for parent rate.
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
This is required to use SWRESET.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
This patch increases reset delay from 50 usec to 80 usec for
USB HOST PHY. In order to reset USB HOST PHY controller properly,
a little extra time is required during its reset cycle.
Signed-off-by: Yulgon Kim <yulgon.kim@samsung.com>
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
This patch adds chained IRQ enter/exit functions to gpio interrupt
handler in order to function correctly on primary controllers with
different methods of flow control.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
This patch adds chained IRQ enter/exit functions to external interrupt
handler in order to function correctly on primary controllers with
different methods of flow control.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
This patch adds chained IRQ enter/exit functions to timer
interrupt handler in order to function correctly on primary
controllers with different methods of flow control.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
When S3C_PM_DEBUG_LED_SMDK is enabled for suspend/resume debugging, the following
compilation error occurs:
arch/arm/mach-s3c64xx/pm.c: In function 's3c_pm_debug_smdkled':
arch/arm/mach-s3c64xx/pm.c:41: error: implicit declaration of function 'gpio_set_value'
arch/arm/mach-s3c64xx/pm.c:41: error: implicit declaration of function 'S3C64XX_GPN'
arch/arm/mach-s3c64xx/pm.c: In function 's3c64xx_pm_init':
arch/arm/mach-s3c64xx/pm.c:184: error: implicit declaration of function 'gpio_request'
arch/arm/mach-s3c64xx/pm.c:188: error: implicit declaration of function 'gpio_direction_output'
Fix the error by including linux/gpio.h
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Fixed the following warning for S5PV210.
arch/arm/mach-s5pv210/pm.c: In function 's5pv210_pm_add':
arch/arm/mach-s5pv210/pm.c:139: warning: assignment from
incompatible pointer type
Also, staticized the function.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
This is a regression fix after migration to the external GIC.
The breakage has been introduced in commit 69644a8e23ab
("ARM: EXYNOS4: modify interrupt mappings for external GIC")
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[kgene.kim@samsung.com: added commit id]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Remove duplicated #include('s) in
arch/arm/mach-exynos4/cpu.c
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Signed-off-by: Jonghwan Choi <jhbird.choi@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Use the correct regulator names for cpufreq
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
WARNING: vmlinux.o(.text+0xf47c): Section mismatch in reference from the function samsung_bl_set() to the (unknown reference) .init.data:(unknown)
The function samsung_bl_set() references
the (unknown reference) __initdata (unknown).
This is often because samsung_bl_set lacks a __initdata
annotation or the annotation of (unknown) is wrong.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
According to commit 659fb32d1b67476f4ade25e9ea0e2642a5b9c4b5
("replace irq_gc_ack() with {set,clr}_bit variants"), this
should be fixed.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Since commit 8560a6cfc9818edde1fd8677961714b264ffa03d
"arm: Footbridge: Use common i8253 clockevent",
ARCH_NETWINDER needs to select CLKEVT_I8253.
This patch fixes below build error with "make netwinder_defconfig".
LD .tmp_vmlinux1
arch/arm/mach-footbridge/built-in.o: In function `isa_timer_init':
isa-rtc.c:(.init.text+0x12c8): undefined reference to `clockevent_i8253_init'
isa-rtc.c:(.init.text+0x12d0): undefined reference to `i8253_clockevent'
arch/arm/mach-footbridge/built-in.o:(.data+0x198): undefined reference to `i8253_clockevent'
make: *** [.tmp_vmlinux1] Error 1
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
enabled
This patch is a workaround for the 364296 ARM1136 r0p2 erratum (possible
cache data corruption with hit-under-miss enabled). It sets the
undocumented bit 31 in the auxiliary control register and the FI bit in
the control register, thus disabling hit-under-miss without putting the
processor into full low interrupt latency mode.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This patch fixes L2 Cache size calculations for L2C-210, L2C-310 and
PL310, by changing the L2X0_AUX_CTRL_WAY_SIZE_MASK from 2 bits to 3
bits.
The Auxiliary Control Register for L2C-210, L2C-310 and PL310 has 3bits
[19:17] for Way size, however the existing code only uses 2 bits to
get this value. This results in incorrect cachesize calculations.
It also results in performing operations on the whole cache when we
erroneously decide that the range is big enough (due to l2x0_size being
too small) and also prints incorrect cachesize.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Cc: stable@kernel.org
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Fix the obvious error in board detection logic, because according to the TS's
manual, the model is stored in the least three significant bits. For example
the byte read on my ts-7300 is 0x23 and the detection then fails.
Cc: Ryan Mallon <ryan@bluewatersys.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Cc: Ryan Mallon <ryan@bluewatersys.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc: (32 commits)
ARM: mmp: Change the way we use timer 0 as clockevent timer.
ARM: mmp: Switch to using timer 1 as clocksource timer.
ARM: mmp: Also start timer 1 on boot.
ARM: pxa168/gplugd: free correct GPIO
ARM: pxa168/gplugd: get rid of mfp-gplugd.h
ARM: pxa: fix logic error in PJ4 iWMMXt handling
mach-sa1100: fix PCI build problem
omap: timer: Set dmtimer used as clocksource in autoreload mode
OMAP3: am3517crane: remove NULL board_mux from board file
arm: mach-omap2: mux: use kstrdup()
arch:arm:plat-omap:iovmm: remove unused variable 'va'
Update Nook Color machine 3284 to common Encore name
am3505/3517: Various platform defines for UART4
OMAP: hwmod: fix build break on non-OMAP4 multi-OMAP2 builds
OMAP: Fix linking error in twl-common.c for OMAP2/3/4 only builds
iMX: Fix build for iMX53
ARM: mx5: board-cpuimx51.c fixup irq_to_gpio() usage
OMAP2+: PM: SmartReflex: use put_sync_suspend for IRQ-safe disabling
OMAP3: beagle: don't touch omap_device internals
OMAP1: enable GENERIC_IRQ_CHIP
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6 into fixes
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ycmiao/pxa-linux-2.6 into fixes
|
|
git://git.pengutronix.de/git/imx/linux-2.6 into fixes
|
|
The current cache detection code does not check for an aliasing
I-cache if the D-cache is found to be VIPT aliasing.
This patch fixes the problem by always checking for an aliasing
I-cache on v6 and later.
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
The smp_twd clockevents driver currently enables the local timer PPI
before the clockevents device is registered. This can lead to a kernel
panic if a spurious timer interrupt is generated before registration
has completed since the kernel will treat it as an IPI timer.
This patch moves the clockevents device registration before the IRQ
unmasking so that we can always handle timer interrupts once they can
occur.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
The various reset routines in mach-realview rely on an FPGA to
power-cycle the board after writing some magic runes to memory-mapped
registers.
This patch adds a dsb() following the writes, so that they become
visible before we mdelay(1000) in the arch_reset code. Without this
patch, the timeout would expire sporadically, causing the reset to fail.
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
