| Age | Commit message (Collapse) | Author |
|---|
|
commit e00c27ef3b4c23e39d0a77b7c8e5be44c28001c7
(ARM: dts: OMAP5: Add Palmas MFD node and regulator nodes)
introduced regulator entries for OMAP5uEVM.
However, currently we use the Palmas regulator names which is used for
different purposes on uEVM. Document the same based on 750-2628-XXX
boards - which is meant to be supported by this dts.
Reported-by: Marc Jüttner <m-juettner@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: J Keerthy <j-keerthy@ti.com>
Acked-by: Benoit Cousson <benoit.cousson@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
- Driver fixes for AM33xx, SIRF and PFC pin controllers
- Fix a compile warning from the pinctrl single-register driver
- Fix a little nasty memory leak
* tag 'pinctrl-for-v3.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: fix a memleak when freeing maps
pinctrl: pinctrl-single: fix compile warning when no CONFIG_PM
pinctrl: sh-pfc: fix SDHI0 VccQ regulator on sh73a0 with DT
arm/dts: sirf: fix the pingroup name mismatch between drivers and dts
pinctrl: sirf: add usp0_uart_nostreamctrl pin group for usp-uart without flowctrl
pinctrl: sirf: fix the pin number and mux bit for usp0
pinctrl: am33xx dt binding: correct include path
|
|
So, there's a comment I put at the top of this, which people seem to
fail to read. So let's fix it for them instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Msm gpiomux can be used only for 7x30 and 8x50.
Prevent compilation and fix build issues on 7X00, 8X60 and 8960.
Signed-off-by: Rohit Vaswani <rvaswani@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
|
|
a.out support on ARM requires that argc, argv and envp are passed in
r0-r2 respectively, which requires hacking load_aout_binary to
prevent argc being clobbered by the return code. Whilst mainline kernels
do set the registers up in start_thread, the aout loader has never
carried the hack in mainline.
Initialising the registers in this way actually goes against the libc
expectations for ELF binaries, where argc, argv and envp are passed on
the stack, with r0 being used to hold a pointer to an exit function for
cleaning up after the dynamic linker if required. If the pointer is
NULL, then it is ignored. When execing an ELF binary, Linux currently
zeroes r0, then sets it to argc and then finally clobbers it with the
return value of the execve syscall, so we actually end up with:
r0 = 0
stack[0] = argc
r1 = stack[1] = argv
r2 = stack[2] = envp
libc treats r1 and r2 as undefined. The clobbering of r0 by sys_execve
works for user-spawned threads, but when executing an ELF binary from a
kernel thread (via call_usermodehelper), the execve is performed on the
ret_from_fork path, which restores r0 from the saved pt_regs, resulting
in argc being presented to the C library. This has horrible consequences
when the application exits, since we have an exit function registered
using argc, resulting in a jump to hyperspace.
This patch solves the problem by removing the partial a.out support from
arch/arm/ altogether.
Cc: <stable@vger.kernel.org>
Cc: Ashish Sangwan <ashishsangwan2@gmail.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
As of commit b9d4d42ad9 (ARM: Remove __ARCH_WANT_INTERRUPTS_ON_CTXSW on
pre-ARMv6 CPUs), the mm switching on VIVT processors is done in the
finish_arch_post_lock_switch() function to avoid whole cache flushing
with interrupts disabled. The need for deferred mm switch is stored as a
thread flag (TIF_SWITCH_MM). However, with preemption enabled, we can
have another thread switch before finish_arch_post_lock_switch(). If the
new thread has the same mm as the previous 'next' thread, the scheduler
will not call switch_mm() and the TIF_SWITCH_MM flag won't be set for
the new thread.
This patch moves the switch pending flag to the mm_context_t structure
since this is specific to the mm rather than thread.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: Marc Kleine-Budde <mkl@pengutronix.de>
Tested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: <stable@vger.kernel.org> # 3.5+
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Commit 93dc688 (ARM: 7684/1: errata: Workaround for Cortex-A15 erratum 798181 (TLBI/DSB operations)) causes the following undefined instruction error on a mx53 (Cortex-A8):
Internal error: Oops - undefined instruction: 0 [#1] SMP ARM
CPU: 0 PID: 275 Comm: modprobe Not tainted 3.11.0-rc2-next-20130722-00009-g9b0f371 #881
task: df46cc00 ti: df48e000 task.ti: df48e000
PC is at check_and_switch_context+0x17c/0x4d0
LR is at check_and_switch_context+0xdc/0x4d0
This problem happens because check_and_switch_context() calls dummy_flush_tlb_a15_erratum() without checking if we are really running on a Cortex-A15 or not.
To avoid this issue, only call dummy_flush_tlb_a15_erratum() inside
check_and_switch_context() if erratum_a15_798181() returns true, which means that we are really running on a Cortex-A15.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Secondary CPUs write to __boot_cpu_mode with caches disabled, and thus a
cached value of __boot_cpu_mode may be incoherent with that in memory.
This could lead to a failure to detect mismatched boot modes.
This patch adds flushing to ensure that writes by secondaries to
__boot_cpu_mode are made visible before we test against it.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Dave Martin <Dave.Martin@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Christoffer Dall <cdall@cs.columbia.edu>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
89ae7b5bbd3e65bc6ab7a577ca5ec18569589c8c
(ARM: shmobile: armadillo800eva: Register pinctrl mapping for INTC)
mistakenly requests GPIO 166 in board code,
most probably due to a wrong merge conflict resolution.
As the GPIO is passed to the st1232 driver through platform
data and requested by the driver,
there's no need to request it in board code. Fix it.
Tested by: Cao Minh Hiep <cm-hiep@jinso.co.jp>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes
From Kukjin Kim:
Samsung fixes for v3.11
- fix kernel booting on exynos5440
skip pm which is not supported
update regarding LPAE features
- fix s3c2440 uart with adding clkdev entries
- fix compilatioin for Samsung SoCs with selecting pm
- update ARCH_NR_GPIO to support exynos4412 has more gpios
* tag 'samsung-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: Update CONFIG_ARCH_NR_GPIO for Exynos
ARM: EXYNOS: Fix low level debug support
ARM: SAMSUNG: Save/restore only selected uart's registers
ARM: SAMSUNG: Add SAMSUNG_PM config option to select pm
ARM: S3C24XX: Add missing clkdev entries for s3c2440 UART
ARM: EXYNOS: Enable 64-bit DMA for EXYNOS5440 if LPAE is enabled
ARM: EXYNOS: change the PHYSMEM_BITS and SECTION_SIZE
ARM: EXYNOS: skip pm support on exynos5440
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Avoids the following warning when SMP is off:
warning: (ARCH_KEYSTONE && SOC_OMAP5) selects ARM_ERRATA_798181 which
has unmet direct dependencies (CPU_V7 && SMP)
Reported-by: Emilio López <emilio@elopez.com.ar>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
With the recent cleanup in Exynos platform code notably commits
17859bec ("ARM: EXYNOS: Do not select legacy Kconfig symbols any
more") and b9222210 ("ARM: EXYNOS: Remove mach/gpio.h"), the definition
of ARCH_NR_GPIOS got removed. This started causing problems on SoCs like
Exynos4412 which have more than the default number of GPIOs. Thus define
this number in KConfig file which takes care of current SoC requirements
and provides scope for GPIO expanders. Without this patch we get the
following errors during boot:
gpiochip_add: gpios 251..258 (gpv0) failed to register
samsung-pinctrl 106e0000.pinctrl: failed to register gpio_chip gpv0, error code: -22
samsung-pinctrl: probe of 106e0000.pinctrl failed with error -22
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Presently, using exynos_defconfig with CONFIG_DEBUG_LL and CONFIG_EARLY_PRIN
on, kernel is not booting, we are getting following:
[ 0.000000] ------------[ cut here ]------------
[ 0.000000] kernel BUG at mm/vmalloc.c:1134!
[ 0.000000] Internal error: Oops - BUG: 0 [#1] PREEMPT SMP ARM
[ 0.000000] Modules linked in:
[ 0.000000] CPU: 0 PID: 0 Comm: swapper Not tainted 3.11.0-rc1 #633
[ 0.000000] task: c052ec48 ti: c0524000 task.ti: c0524000
[ 0.000000] PC is at vm_area_add_early+0x54/0x94
[ 0.000000] LR is at add_static_vm_early+0xc/0x60
Its because exynos[4/5]_map_io() function ioremaps a single 512KB memory
size for all the four uart ports which envelopes the mapping created by
debug_ll_io_init(), called earlier in exynos_init_io().
This patch removes iodesc entries for UART controller for all Samsung SoC's,
since now the Samsung uart driver does a ioremap during probe and any needed
iomapping for earlyprintk will be handled by debug_ll_io_init().
Tested on smdk4412 and smdk5250.
Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Basically this code gets executed only during debugging i.e when
DEBUG_LL & SAMSUNG_PM_DEBUG is on, so required only for UART used
for debugging. Since we are removing static iodesc entries for UARTs,
so now only the selected (CONFIG_DEBUG_S3C_UART) UART will be
ioremapped by the debug_ll_io_init() for DEBUG_LL, so save/restore
uart registers only for selected uart.
Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
This patch enables the selection of samsung pm related stuffs
when SAMSUNG_PM config is enabled and not just when generic PM
config is enabled. Power management for s3c64XX and s3c24XX
is enabled by default and for other platform depends on S5P_PM.
This patch also fixes the following compilation error's when compiling
a platform like exynos5440 which does not select pm stuffs.
arch/arm/mach-exynos/built-in.o: In function '__virt_to_phys':
linux/arch/arm/include/asm/memory.h:175: undefined reference to 's3c_cpu_resume'
linux/arch/arm/include/asm/memory.h:175: undefined reference to 's3c_cpu_resume'
linux/arch/arm/include/asm/memory.h:175: undefined reference to 's3c_cpu_resume'
linux/arch/arm/include/asm/memory.h:175: undefined reference to 's3c_cpu_resume'
arch/arm/mach-exynos/built-in.o: In function 'exynos5_init_irq':
linux/arch/arm/mach-exynos/common.c:492: undefined reference to 's3c_irq_wake'
linux/arch/arm/mach-exynos/common.c:492: undefined reference to 's3c_irq_wake'
arch/arm/mach-exynos/built-in.o: In function 'exynos4_init_irq':
linux/arch/arm/mach-exynos/common.c:476: undefined reference to 's3c_irq_wake'
linux/arch/arm/mach-exynos/common.c:476: undefined reference to 's3c_irq_wake'
arch/arm/plat-samsung/built-in.o: In function 's3c_irqext_wake':
linux/arch/arm/plat-samsung/pm.c:144: undefined reference to 's3c_irqwake_eintallow'
linux/arch/arm/plat-samsung/pm.c:144: undefined reference to 's3c_irqwake_eintallow'
arch/arm/plat-samsung/built-in.o: In function 's3c_pm_enter':
linux/arch/arm/plat-samsung/pm.c:263: undefined reference to 's3c_irqwake_intallow'
linux/arch/arm/plat-samsung/pm.c:263: undefined reference to 's3c_irqwake_intallow'
linux/arch/arm/plat-samsung/pm.c:264: undefined reference to 's3c_irqwake_eintallow'
linux/arch/arm/plat-samsung/pm.c:264: undefined reference to 's3c_irqwake_eintallow'
linux/arch/arm/plat-samsung/pm.c:275: undefined reference to 's3c_pm_save_core'
linux/arch/arm/plat-samsung/pm.c:279: undefined reference to 's3c_pm_configure_extint'
linux/arch/arm/plat-samsung/pm.c:310: undefined reference to 's3c_pm_restore_core'
make: *** [vmlinux] Error 1
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
This patch restores serial port operation which has been broken since
commit 60e93575476f ("serial: samsung: enable clock before clearing
pending interrupts during init")
That commit only uncovered the real issue which was missing clkdev
entries for the "uart" clocks on S3C2440. It went unnoticed so far
because return value of clk API calls were not being checked at all
in the samsung serial port driver.
This patch should be backported to at least 3.10 stable kernel, since
the serial port has not been working on s3c2440 since 3.10-rc5.
Cc: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
[on S3C2440 SoC based Mini2440 board]
Tested-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Tested-by: Juergen Beisert <jbe@pengutronix.de>
Cc: <stable@vger.kernel.org> [3.10]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
CONFIG_USB_EHCI_MXC selects the old i.mx USB driver, which does not support
device tree.
Select the USB chipidea driver instead, so that USB can be functional on i.mx.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The em_x270_mci_setpower() and em_x270_usb_hub_init() functions
call regulator_enable(), which may return an error that must
be checked.
This changes the em_x270_usb_hub_init() function to bail out
if it fails, and changes the pxamci_platform_data->setpower
callback so that the a failed em_x270_mci_setpower call
can be propagated by the pxamci driver into the mmc core.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Mike Rapoport <mike@compulab.co.il>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Acked-by: Chris Ball <cjb@laptop.org>
[olof: fixed order of regulator_enable() and test in em_x270_usb_hub_init]
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Fix the following compilation warning:
arch/arm/mach-zynq/common.c:110:2: warning: initialization from incompatible pointer type [enabled by default]
arch/arm/mach-zynq/common.c:110:2: warning: (near initialization for ‘__mach_desc_XILINX_EP107.restart’) [enabled by default]
Signed-off-by: Vincent Stehlé <vincent.stehle@freescale.com>
Cc: Robin Holt <holt@sgi.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: trivial@kernel.org
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Fix the following compilation warning:
arch/arm/mach-keystone/keystone.c:74:2: warning: initialization from incompatible pointer type [enabled by default]
arch/arm/mach-keystone/keystone.c:74:2: warning: (near initialization for ‘__mach_desc_KEYSTONE.restart’) [enabled by default]
Signed-off-by: Vincent Stehlé <vincent.stehle@freescale.com>
Cc: Robin Holt <holt@sgi.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: trivial@kernel.org
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Commit 7b6d864b48d9 (reboot: arm: change reboot_mode to use enum
reboot_mode) and ff701306cd49 (arm64: use common reboot infrastructure)
change the prototype of arm_pm_restart on arm and arm64.
Update xen_restart accordingly.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
|
|
Midway adds new register fields to the coherency control registers, so
writing absolute values will break on Midway. Change the register
accesses to only modify the necessary and common fields in order to
support both Midway and Highbank.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik into fixes
From Linus Walleij:
This updates the Nomadik defconfig post-v3.11-rc1:
- Update the baseline so we need not rely on make
oldconfig so much
- MMC defconfig updates
- Activate NO_HZ_IDLE and HRTIMERS
* tag 'nomadik-defconfig-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
ARM: nomadik: configure for NO_HZ and HRTIMERS
ARM: nomadik: update defconfig base
ARM: nomadik: Update MMC defconfigs
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Commit 8ef6e6201b26cb9fde79c1baa08145af6aca2815 (ARM: footbridge: use
fixed PCI i/o mapping) broke booting on my netwinder. Before that,
everything boots fine. Since then, it crashes on boot.
With earlyprintk, I see it BUG-ing like so:
kernel BUG at lib/ioremap.c:27!
Internal error: Oops - BUG: 0 [#1] ARM
...
[<c0139b54>] (ioremap_page_range+0x128/0x154) from [<c02e6a6c>] (dc21285_setup+0xd0/0x114)
[<c02e6a6c>] (dc21285_setup+0xd0/0x114) from [<c02e4874>] (pci_common_init+0xa0/0x298)
[<c02e4874>] (pci_common_init+0xa0/0x298) from [<c02e793c>] (netwinder_pci_init+0xc/0x18)
[<c02e793c>] (netwinder_pci_init+0xc/0x18) from [<c02e27d0>] (do_one_initcall+0xb4/0x180)
...
Russell points out it's because of overlapping PCI mappings that was
added with the aforementioned commit. Rob thought the code would re-use
the static mapping, but that turns out to not be the case and instead
hits the BUG further down.
After deleting this hunk as suggested by Russel, the system boots up fine
again and all my PCI devices work (IDE, ethernet, the DC21285).
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Cc: stable@vger.kernel.org # v3.5+
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
into fixes
From Shawn Guo, imx fixes for 3.11:
- A few device tree source fixes regarding pinctrl, clock, and pwm
backlight.
- Fixes imx28 and imx51 audio driver failure caused by sgtl5000 codec
driver change by supplying the correct clock for codec.
- imx6q emi_sel clock muxing and imx6q-iomuxc-gpr macro fixes
* tag 'imx-fixes-3.11' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: dts: imx51-babbage: Pass a real clock to the codec
ARM i.MX53: mba53: Fix PWM backlight DT node
ARM: imx: fix vf610 enet module clock selection
ARM: mxs: saif0 is the clock provider to sgtl5000
ARM: i.MX6Q: correct emi_sel clock muxing
ARM i.MX6Q: Fix IOMUXC GPR1 defines for ENET_CLK_SEL and IPU1/2_MUX
ARM: i.MX27: Typo fix
ARM: imx27: Fix documentation for SPLL clock
ARM i.MX53: Fix UART pad configuration
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
From Tony Lindgren:
Omap fixes mostly to deal with the dropping of platform data for omap4,
and to make v7_defconfig bootable on omap4 SDP with nfsroot.
* tag 'omap-for-v3.11/fixes-against-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Provide alias to USB PHY clock
ARM: dts: Add missing vmmc2 regulator for twl
ARM: multi_v7: Enabled omap4430 sdp nfsroot
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into fixes
From Sekhar Nori:
DaVinci fixes for v3.11-rc2
The pull request includes fixes for sparse warnings, defconfig changes to
enable DMA usage on peripherals and removal of a duplicated include file.
* tag 'davinci-fixes-for-v3.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: davinci: defconfig: enable EDMA driver
ARM: davinci: make file local variables static
ARM: edma: remove duplicated include from edma.c
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Some of the ARM_ERRATA selection is not done in the initial SOC support
patches. This patch selects 2 new ARM_ERRATA's and removes one which was
actually fixed.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
[olof: reorder new errata entries]
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
This patch fixes a bug in pinctrl setup of serial2 device, Some of the
pins in the pinctrl node of serial2 do not belong to that
pin-controller. This patch divides them in the pins into there
respective pin controller nodes.
Without this patch serial on StiH416-B2000 Board will not work as it
fails with:
"st-pinctrl pin-controller-rear.3: failed to get pin(99) name
st-pinctrl pin-controller-rear.3: maps: function serial2 group serial2-0
num 4
pinconfig core: failed to register map default (3): no group/pin given"
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Commit a469abd0f868 ("ARM: elf: add new hwcap for identifying atomic
ldrd/strd instructions") added a new hwcap to identify LPAE on CPUs
which support it. Whilst the hwcap data is correct, the string reported
in /proc/cpuinfo actually matches on HWCAP_VFPD32, which was missing
an entry in the string table.
This patch fixes this problem by adding a "vfpd32" string at the correct
offset, preventing us from falsely advertising LPAE on CPUs which do not
support it.
[will: added commit message]
Acked-by: Will Deacon <will.deacon@arm.com>
Tested-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Tetsuyuki Kobayashi <koba@kmckk.co.jp>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Currently, compare_cpu_mode_with_primary uses a mixture of macro
arguments and hardcoded registers, and does so incorrectly, as it
stores (__boot_cpu_mode_offset | BOOT_CPU_MODE_MISMATCH) to
(__boot_cpu_mode + &__boot_cpu_mode_offset), which could corrupt an
arbitrary portion of memory.
This patch fixes up compare_cpu_mode_with_primary to use the macro
arguments, correctly updating __boot_cpu_mode.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Dave Martin <Dave.Martin@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Christoffer Dall <cdall@cs.columbia.edu>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
When map_lowmem() runs, and processes a memory bank whose start or end
is not section-aligned, memory must be allocated to store the 2nd-level
page tables. Those allocations are made by calling memblock_alloc().
At this point, the only memory that is free *and* mapped is memory which
has already been mapped by map_lowmem() itself. For this reason, we must
calculate the first point at which map_lowmem() will need to allocate
memory, and set the memblock allocation limit to a lower address, so that
memblock_alloc() is guaranteed to return memory that is already mapped.
This patch enhances sanity_check_meminfo() to calculate that memory
address, and pass it to memblock_set_current_limit(), rather than just
assuming the limit is arm_lowmem_limit.
The algorithm applied is:
* Default memblock_limit to arm_lowmem_limit in the absence of any other
limit; arm_lowmem_limit is the highest memory that is mapped by
map_lowmem().
* While walking the list of memblocks, if the start of a block is not
aligned, 2nd-level page tables will need to be allocated to map the
first few pages of the block. Hence, the memblock_limit must be before
the start of the block.
* Similarly, if the end of any block is not aligned, 2nd-level page
tables will need to be allocated to map the last few pages of the
block. Hence, the memblock_limit must point at the end of the block,
rounded down to section-alignment.
* The memory blocks are assumed to be sorted in address order, so the
first unaligned block start or end is used to set the limit.
With this algorithm, the start or end of almost any bank can be non-
section-aligned. The only exception is that the start of bank 0 must
be section-aligned, since otherwise memory would need to be allocated
when mapping the start of bank 0, which occurs before any free memory
is mapped.
[swarren, wrote commit description, rewrote calculation of memblock_limit]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Commit ae8a8b9553bd ("ARM: 7691/1: mm: kill unused TLB_CAN_READ_FROM_L1_CACHE
and use ALT_SMP instead") added early function returns for page table
cache flushing operations on ARMv7 SMP CPUs.
Unfortunately, when targetting Thumb-2, these `mov pc, lr' sequences
assemble to 2 bytes which can lead to corruption of the instruction
stream after code patching.
This patch fixes the alternates to use wide (32-bit) instructions for
Thumb-2, therefore ensuring that the patching code works correctly.
Cc: <stable@vger.kernel.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This non-user visible option lacked any kind of documentation. This
is quite common for non-user visible options; certian people can't
understand the point of documenting such options with help text.
However, here we have a case in point: developers don't understand the
option either, as they were thinking that when the option is not set,
the decompressor should produce no output what so ever. This is
incorrect, as the purpose of this option is to control whether a
multiplatform kernel uses the kernel debugging macros to produce
output or not.
So let's document this via help rather than commentry to prevent others
falling into this misunderstanding.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
in drivers/pinctrl/sirf, pingroup name is cko0 and cko1, but in dts, they
are cko0 and cko1_rst. this patch fixes the error in dts.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
flowctrl
this patch adds the lost pin group which supports to let USP0 to simulate
a UART without hardware flow control.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This enables tickless idle (NO_HZ_IDLE) and high resolution
timers for the Nomadik.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Update the Nomadik defconfig enabling:
- GPIO keyboard input
- Regulators
- LED class driver
- LED heartbeat trigger
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Enable MMC_UNSAFE_RESUME to accomplish a proper suspend/resume cycle
for SD/SDIO/(e)MMC.
ARMMMCI host driver supports clock gating through runtime PM, thus
MMC_CLKGATE is not needed. Moreover ARMMMCI can do scatter-gather which
means we can explicity disable MMC_BLOCK_BOUNCE, since it's default
enabled, to skip unnecessary bounce buffer copying.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fixes from Rafael Wysocki:
"These are fixes collected over the last week, most importnatly two
cpufreq reverts fixing regressions introduced in 3.10, an autoseelp
fix preventing systems using it from crashing during shutdown and two
ACPI scan fixes related to hotplug.
Specifics:
- Two cpufreq commits from the 3.10 cycle introduced regressions.
The first of them was buggy (it did way much more than it needed to
do) and the second one attempted to fix an issue introduced by the
first one. Fixes from Srivatsa S Bhat revert both.
- If autosleep triggers during system shutdown and the shutdown
callbacks of some device drivers have been called already, it may
crash the system. Fix from Liu Shuo prevents that from happening
by making try_to_suspend() check system_state.
- The ACPI memory hotplug driver doesn't clear its driver_data on
errors which may cause a NULL poiter dereference to happen later.
Fix from Toshi Kani.
- The ACPI namespace scanning code should not try to attach scan
handlers to device objects that have them already, which may
confuse things quite a bit, and it should rescan the whole
namespace branch starting at the given node after receiving a bus
check notify event even if the device at that particular node has
been discovered already. Fixes from Rafael J Wysocki.
- New ACPI video blacklist entry for a system whose initial backlight
setting from the BIOS doesn't make sense. From Lan Tianyu.
- Garbage string output avoindance for ACPI PNP from Liu Shuo.
- Two Kconfig fixes for issues introduced recently in the s3c24xx
cpufreq driver (when moving the driver to drivers/cpufreq) from
Paul Bolle.
- Trivial comment fix in pm_wakeup.h from Chanwoo Choi"
* tag 'pm+acpi-3.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / video: ignore BIOS initial backlight value for Fujitsu E753
PNP / ACPI: avoid garbage in resource name
cpufreq: Revert commit 2f7021a8 to fix CPU hotplug regression
cpufreq: s3c24xx: fix "depends on ARM_S3C24XX" in Kconfig
cpufreq: s3c24xx: rename CONFIG_CPU_FREQ_S3C24XX_DEBUGFS
PM / Sleep: Fix comment typo in pm_wakeup.h
PM / Sleep: avoid 'autosleep' in shutdown progress
cpufreq: Revert commit a66b2e to fix suspend/resume regression
ACPI / memhotplug: Fix a stale pointer in error path
ACPI / scan: Always call acpi_bus_scan() for bus check notifications
ACPI / scan: Do not try to attach scan handlers to devices having them
|
|
|
|
Fix the the gpio reg address for the device tree entry.
Signed-off-by: Rohit Vaswani <rvaswani@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
|
|
Kconfig symbol S3C24XX_PLL depends on ARM_S3C24XX. But that symbol
doesn't exist. Commit f023f8dd59bf ("cpufreq: s3c24xx: move cpufreq
driver to drivers/cpufreq"), which added this issue, makes it clear
that ARM_S3C24XX_CPUFREQ was intended here.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Enable EDMA dmaengine driver by default in DaVinci
defconfig files as it is required for DMA support
on MMC/SD, SPI etc.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
Make file local variables static in mach-davinci.
This fixes sparse warnings of the form:
arch/arm/mach-davinci/dm355.c:863:27: warning: symbol 'dm355_venc_pdata' was not declared. Should it be static?
Cc: Prabhakar Lad <prabhakar.csengg@gmail.com>
Acked-by: Prabhakar Lad <prabhakar.csengg@gmail.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
Remove duplicated include.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
Till the OMAP clocks are correctly defined in device tree, use
this temporary hack to provide clock alias to the USB PHY clocks.
Without this, USB Host & Ethernet will not be functional with
device tree boots on Panda and uEVM.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Allow 64-bit DMA addresses if LPAE is enabled on EXYNOS5440.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
On EXYNOS5440 there is DRAM on the 36-bit address range. Hence
this patch converts the MAX_PHYSMEM_BITS macro to 36 if LPAE is
enabled for the ARM architecture.
The conventional section size on EXYNOS is 256M due to sparsemem.
Since EXYNOS5440 has memory in multiples of 1G in 32-bit and 36-bit
range, this has now been modified to 31.
Signed-off-by: Subash Patel <subash.rp@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
EXYNOS5440 doesn't support PM and current single image for EXYNOS
will be break without this patch. Actually, SSDK5440 cannot boot
without this so this should be merged during rc.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
