summaryrefslogtreecommitdiff
path: root/arch/arm
AgeCommit message (Collapse)Author
2013-06-08Merge tag 'fixes-for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc Pull ARM SoC fixes from Olof Johansson: "Another week, another batch of fixes for arm-soc platforms. Nothing controversial here, a handful of fixes for regressions and/or serious problems across several of the platforms. Things are slowing down nicely on fix rates for 3.10" * tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: ARM: exynos: add debug_ll_io_init() call in exynos_init_io() ARM: EXYNOS: uncompress - print debug messages if DEBUG_LL is defined ARM: shmobile: sh73a0: Update CMT clockevent rating to 80 sh-pfc: r8a7779: Don't group USB OVC and PENC pins ARM: mxs: icoll: Fix interrupts gpio bank 0 ARM: imx: clk-imx6q: AXI clock select index is incorrect ARM: bcm2835: override the HW UART periphid ARM: mvebu: Fix bug in coherency fabric low level init function ARM: Kirkwood: TS219: Fix crash by double PCIe instantiation ARM: ux500: Provide supplies for AUX1, AUX2 and AUX3 ARM: ux500: Only configure wake-up reasons on ux500 based platforms ARM: dts: imx: fix clocks for cspi ARM i.MX6q: fix for ldb_di_sels
2013-06-08Merge tag 'imx-fixes-3.10-2' of ↵Olof Johansson
git://git.linaro.org/people/shawnguo/linux-2.6 into fixes From Shawn Guo, imx fixes for 3.10, take 2: - One device tree fix for all spi node to have per clock added. The clock is needed by spi driver to calculate bit rate divisor. The spi node in the current device trees either does not have the clock or is defined as dummy clock, in which case the driver probe will fail or spi will run at a wrong bit rate. - Two imx6q clock fixes, which correct axi_sels and ldb_di_sels. * tag 'imx-fixes-3.10-2' of git://git.linaro.org/people/shawnguo/linux-2.6: ARM: imx: clk-imx6q: AXI clock select index is incorrect ARM: dts: imx: fix clocks for cspi ARM i.MX6q: fix for ldb_di_sels Signed-off-by: Olof Johansson <olof@lixom.net>
2013-06-08ARM: exynos: add debug_ll_io_init() call in exynos_init_io()Doug Anderson
If the early MMU mapping of the UART happens to get booted out of the TLB between the start of paging_init() and when we finally re-add the UART at the very end of s3c_init_cpu(), we'll get a hang at bootup if we've got early_printk enabled. Avoid this hang by calling debug_ll_io_init() early. Without this patch, you can reliably reproduce a hang when early printk is enabled by adding flush_tlb_all() at the start of exynos_init_io(). After this patch the hang goes away. Signed-off-by: Doug Anderson <dianders@chromium.org> Acked-by: Kukjin Kim <kgene.kim@samsung.com> Signed-off-by: Olof Johansson <olof@lixom.net>
2013-06-08Merge tag 'renesas-fixes-for-v3.10' of ↵Olof Johansson
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes From Simon Horman, Renesas ARM based SoC fixes for v3.10: - Correction to USB OVC and PENC pin groupings on r8a7779 SoC. This avoids conflicts when the USB_OVCn pins are used by another function. This has been observed to be a problem in v3.10-rc1. - Update CMT clock rating for sh73a0 SoC to resolve boot failure on kzm9g-reference. This resolves a regression between v3.9 and v3.10-rc1. * tag 'renesas-fixes-for-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: ARM: shmobile: sh73a0: Update CMT clockevent rating to 80 sh-pfc: r8a7779: Don't group USB OVC and PENC pins Signed-off-by: Olof Johansson <olof@lixom.net>
2013-06-08ARM: EXYNOS: uncompress - print debug messages if DEBUG_LL is definedTushar Behera
Printing low-level debug messages make an assumption that the specified UART port has been preconfigured by the bootloader. Incorrectly specified UART port results in system getting stalled while printing the message "Uncompressing Linux... done, booting the kernel" This UART port number is specified through S3C_LOWLEVEL_UART_PORT. Since the UART port might different for different board, it is not possible to specify it correctly for every board that use a common defconfig file. Calling this print subroutine only when DEBUG_LL fixes the problem. By disabling DEBUG_LL in default config file, we would be able to boot multiple boards with different default UART ports. With this current approach, we miss the print "Uncompressing Linux... done, booting the kernel." when DEBUG_LL is not defined. Signed-off-by: Tushar Behera <tushar.behera@linaro.org> Signed-off-by: Olof Johansson <olof@lixom.net>
2013-06-06arch, mm: Remove tlb_fast_mode()Peter Zijlstra
Since the introduction of preemptible mmu_gather TLB fast mode has been broken. TLB fast mode relies on there being absolutely no concurrency; it frees pages first and invalidates TLBs later. However now we can get concurrency and stuff goes *bang*. This patch removes all tlb_fast_mode() code; it was found the better option vs trying to patch the hole by entangling tlb invalidation with the scheduler. Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Russell King <linux@arm.linux.org.uk> Cc: Tony Luck <tony.luck@intel.com> Reported-by: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: Peter Zijlstra <peterz@infradead.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-06-05Merge branch 'fixes' of git://git.kernel.org/pub/scm/virt/kvm/kvmLinus Torvalds
Pull kvm bugfixes from Gleb Natapov: "The bulk of the fixes is in MIPS KVM kernel<->userspace ABI. MIPS KVM is new for 3.10 and some problems were found with current ABI. It is better to fix them now and do not have a kernel with broken one" * 'fixes' of git://git.kernel.org/pub/scm/virt/kvm/kvm: KVM: Fix race in apic->pending_events processing KVM: fix sil/dil/bpl/spl in the mod/rm fields KVM: Emulate multibyte NOP ARM: KVM: be more thorough when invalidating TLBs ARM: KVM: prevent NULL pointer dereferences with KVM VCPU ioctl mips/kvm: Use ENOIOCTLCMD to indicate unimplemented ioctls. mips/kvm: Fix ABI by moving manipulation of CP0 registers to KVM_{G,S}ET_ONE_REG mips/kvm: Use ARRAY_SIZE() instead of hardcoded constants in kvm_arch_vcpu_ioctl_{s,g}et_regs mips/kvm: Fix name of gpr field in struct kvm_regs. mips/kvm: Fix ABI for use of 64-bit registers. mips/kvm: Fix ABI for use of FPU.
2013-06-04ARM: shmobile: sh73a0: Update CMT clockevent rating to 80Simon Horman
Update the CMT clockevent rating from 125 to 80. This resolves a boot-failure regression for kzm9g-reference in v3.10-rc1 introduced by f7db706b132f11c79ae1d74b2382e0926cf31644 ("ARM: 7674/1: smp: Avoid dummy clockevent being preferred over real"). The patch noted above reduces the rating of dummy clockevent from 400 to 100. This patch reduces the rating of CMT so that it is once again less than that of the dummy clockevent. Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2013-06-03ARM: KVM: be more thorough when invalidating TLBsMarc Zyngier
The KVM/ARM MMU code doesn't take care of invalidating TLBs before freeing a {pte,pmd} table. This could cause problems if the page is reallocated and then speculated into by another CPU. Reported-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Acked-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Christoffer Dall <cdall@cs.columbia.edu>
2013-06-03ARM: KVM: prevent NULL pointer dereferences with KVM VCPU ioctlAndre Przywara
Some ARM KVM VCPU ioctls require the vCPU to be properly initialized with the KVM_ARM_VCPU_INIT ioctl before being used with further requests. KVM_RUN checks whether this initialization has been done, but other ioctls do not. Namely KVM_GET_REG_LIST will dereference an array with index -1 without initialization and thus leads to a kernel oops. Fix this by adding checks before executing the ioctl handlers. [ Removed superflous comment from static function - Christoffer ] Changes from v1: * moved check into a static function with a meaningful name Signed-off-by: Andre Przywara <andre.przywara@linaro.org> Signed-off-by: Christoffer Dall <cdall@cs.columbia.edu>
2013-06-03ARM: imx: clk-imx6q: AXI clock select index is incorrectAnson Huang
The AXI clock mux should be as below: 00: periph; 01: pll2_pfd2_396m; 10: periph; 11: pll3_pfd1_540m; Signed-off-by: Anson Huang <b20788@freescale.com> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-06-02Merge tag 'ux500-arm-soc-v3.10-fixes-2' of ↵Olof Johansson
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into fixes From Linus Walleij, ux500 fixes for v3.10: - A multiplatform fix making sure ux500_idle_init() is only executed on ux500. - A regulator fix making sure the MMC/SD card regulator is not disabled on boot. Signed-off-by: Olof Johansson <olof@lixom.net> * tag 'ux500-arm-soc-v3.10-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson: ARM: ux500: Provide supplies for AUX1, AUX2 and AUX3 ARM: ux500: Only configure wake-up reasons on ux500 based platforms
2013-06-02ARM: bcm2835: override the HW UART periphidJongsung Kim
Stephen Warren reported the recent commit 78506f2 (add support for extended FIFO-size of PL011-r1p5) breaks the serial port on the BCM2835 ARM SoC. A UART compatible with the ARM PL011-r1p5 should have 32-deep FIFOs. The BCM2835 UART just looks like an ARM PL011-r1p5, but has 16-deep FIFOs just like PL011-r1p4 or earlier revisions. As a workaround for this compatibility issue, this patch overrides the HW UART periphid register values with the actually compatible UART periphid 0x00241011 (r1p3 or r1p4). Reported-by: Stephen Warren <swarren@wwwdotorg.org> Signed-off-by: Jongsung Kim <neidhard.kim@lge.com> Signed-off-by: Stephen Warren <swarren@wwwdotorg.org> Signed-off-by: Olof Johansson <olof@lixom.net>
2013-06-02Merge tag 'fixes-3.10-3' of git://git.infradead.org/users/jcooper/linux into ↵Olof Johansson
fixes From Jason Cooper, mvebu fixes for v3.10 round 3: - mvebu - fix bug in coherency fabric low level init - kirkwood - fix crash from pcie double init Signed-off-by: Olof Johansson <olof@lixom.net> * tag 'fixes-3.10-3' of git://git.infradead.org/users/jcooper/linux: ARM: mvebu: Fix bug in coherency fabric low level init function ARM: Kirkwood: TS219: Fix crash by double PCIe instantiation
2013-05-29Merge tag 'pinctrl-fixes-v3.10-3' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl Pull pin-control fixes from Linus Walleij: - Six patches fixing up the suspend/resume and wakeup handling of the Samsung and Exynos drivers. - Errorpath fixes for four different drivers. All on the probe() errorpath. - Make the debugfs code for pin config take the right mutex. * tag 'pinctrl-fixes-v3.10-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: pinctrl: pinconf: take the right mutex pinctrl: sunxi: fix error return code in sunxi_pinctrl_probe() pinctrl: exynos: Handle suspend/resume of GPIO EINT registers pinctrl: samsung: Allow per-bank SoC-specific private data pinctrl: samsung: Add support for SoC-specific suspend/resume callbacks pinctrl: Don't override the error code in probe error handling ARM: EXYNOS: Fix EINT wake-up mask configuration when pinctrl is used pinctrl: exynos: Add support for set_irq_wake of wake-up EINTs pinctrl: samsung: fix suspend/resume functionality
2013-05-29Merge tag 'fixes-for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc Pull ARM Exynos fixes from Olof Johansson: "Here's a shorter set of fixes for 3.10, all for Samsung Exynos platforms. It also includes a defconfig update so that exynos_defconfig provides a meaningful set of drivers to boot an unmodified kernel on the Samsung ARM-based Chromebooks." * tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: ARM: exynos: defconfig update ARM: SAMSUNG: Add names to fimd0 IRQ resources ARM: EXYNOS: fix software reset logic for EXYNOS5440 SOC ARM: EXYNOS: Fix support of Exynos4210 rev0 SoC ARM: dts: Enabling samsung-usb2phy driver for exynos5250
2013-05-29ARM: exynos: defconfig updateOlof Johansson
This turns on a number of configs that are useful on the Chromebook, but also good to have on in general: * USB host and MMC drivers(!) * I2C GPIO arbitration driver * CYAPA trackpad driver * simplefb * CROS EC and keyboard drivers * S5M8767 driver * MAX77686 drivers * MAX8997 driver * DEVTMPFS + mount * DM_CRYPT (as module) * CRYPTOLOOP * HIGHMEM * PRINTK timestamps This also turns off DEBUG_LL, and switches the hardcoded Samsung lowlevel uart to uart 3 (which is only used to show the "uncompressing kernel" message at boot, it seems). Signed-off-by: Olof Johansson <olof@lixom.net> Reviewed-by: Doug Anderson <dianders@chromium.org> Tested-by: Tushar Behera <tushar.behera@linaro.org> Acked-by: Kukjin Kim <kgene.kim@samsung.com>
2013-05-28ARM: mvebu: Fix bug in coherency fabric low level init functionNadav Haklai
When adding CPU to the SMP group and enabling the coherency on this CPU we must protect the register access. The previous implementation claims to be atomic but doesn't provide any protection against parallel access to the coherency fabric control and configuration registers. This patch fixes this by using the ldrex and strex mechanism. This method should be used in all accesses to those registers. [gregory.clement@free-electrons.com: fixed the commit's topic] Signed-off-by: Nadav Haklai <nadavh@marvell.com> Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
2013-05-28ARM: Kirkwood: TS219: Fix crash by double PCIe instantiationAndrew Lunn
When creating the DT based boards-ts219.c the none DT ts219-setup.c was used as a template. This includes a lateinit() call to initialize the PCIe bus. The code makes use of machine_is_ts219() which is never true on DT, so a FIXME was added and the code left as is. This was unproblematic until b73690c8f8b5d: "ARM: Kirkwood: Support basic hotplug for PCI-E" which changes the way the PCIe bus is initialized. The non-DT ts219-setup.c now crashes during boot. The lateinit() call in the DT boards-ts219.c is being called, machine_is_ts219() is true and so the PCIe is initialized a second time. This patch removes the useless, and now clearly dangerous, code from boards-ts219.c, making ts219-setup.c work again. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Cc: <stable@vger.kernel.org> # v3.9.x Signed-off-by: Jason Cooper <jason@lakedaemon.net>
2013-05-28Merge tag 'samsung-fixes-3' of ↵Olof Johansson
git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes From Kukjin Kim: Fixes following for v3.10 - to get usb2 working on the Chromebook with adding the usb phy node for usb2 on exynos5250 - supporting exynos4210 rev0 SoC - exynos5440 restart applying only to powered-on domains - drm-exynos probe failure with adding resource names to fimd0 platform device * tag 'samsung-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung: ARM: SAMSUNG: Add names to fimd0 IRQ resources ARM: EXYNOS: fix software reset logic for EXYNOS5440 SOC ARM: EXYNOS: Fix support of Exynos4210 rev0 SoC ARM: dts: Enabling samsung-usb2phy driver for exynos5250
2013-05-27ARM: EXYNOS: Fix EINT wake-up mask configuration when pinctrl is usedTomasz Figa
On DT-enabled systems pinctrl-exynos driver is responsible for handling of wake-up EINT interrupts. This patch adjusts wake-up mask configuration code to take wake-up mask value from pinctrl-exynos driver on DT-enabled systems. Signed-off-by: Tomasz Figa <t.figa@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Tested-by: Doug Anderson <dianders@chromium.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2013-05-27ARM: ux500: Provide supplies for AUX1, AUX2 and AUX3Lee Jones
This patch fixes a bug introduced in the v3.10 merge window. The AB8500 External Regulator driver has recently landed upstream, which registers each of the 3 external regulators located on the AB8500. If these regulators are marked as 'always on', there is a potential for power-loss. If they're not and are seemingly unused the Regulator subsystem will attempt to disable them to save power. This causes an issue for AUX1, AUX2 and AUX3 as they obtain their power from EXT3. So we're specifying that here to prevent EXT3 from being powered down. Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2013-05-27ARM: ux500: Only configure wake-up reasons on ux500 based platformsLee Jones
Multiplatform calls all enabled platforms' initcalls. In the ux500_idle_init() initcall we call into the DBx500-PRCMU which in turn executes some ux500 specific register reads/writes. When running on some !ux500 platforms this ends up causing a kernel Oops. This patch ensures the PRCMU call is only invoked when running on ux500 based platforms. Reported-by: Rob Herring <rob.herring@calxeda.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2013-05-25Merge branch 'fixes' of git://git.linaro.org/people/rmk/linux-armLinus Torvalds
Pull ARM fixes from Russell King: "Just three this time, all really quite small" * 'fixes' of git://git.linaro.org/people/rmk/linux-arm: ARM: 7729/1: vfp: ensure VFP_arch is non-zero when VFP is not supported ARM: 7727/1: remove the .vm_mm value from gate_vma ARM: 7723/1: crypto: sha1-armv4-large.S: fix SP handling
2013-05-24Merge tag 'fixes-for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc Pull ARM SoC fixes from Olof Johansson: "We didn't have any fixes sent up for -rc2, so this is a slightly larger batch. A bit all over the place platform-wise; OMAP, at91, marvell, renesas, sunxi, ux500, etc. I tried to summarize highlights but there isn't a whole lot to point out. Lots of little things fixed all over. A couple of defconfig updates due to new/changing options." * tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (44 commits) ARM: at91/sama5: fix incorrect PMC pcr div definition ARM: at91/dt: fix macb pinctrl_macb_rmii_mii_alt definition ARM: at91: at91sam9n12: move external irq declatation to DT ARM: shmobile: marzen: Use error values in usb_power_* ARM: tegra: defconfig fixes ARM: nomadik: fix IRQ assignment for SMC ethernet ARM: vt8500: Add missing NULL terminator in dt_compat clk: tegra: add ac97 controller clock clk: tegra: remove USB from clk init table ARM: dts: mvebu: Fix wrong the address reg value for the L2-cache node ARM: plat-orion: Fix num_resources and id for ge10 and ge11 ARM: OMAP2+: hwmod: Remove sysc slave idle and auto idle apis SERIAL: OMAP: Remove the slave idle handling from the driver ARM: OMAP2+: serial: Remove the un-used slave idle hooks ARM: OMAP2+: hwmod-data: UART IP needs software control to manage sidle modes ARM: OMAP2+: hwmod: Add a new flag to handle SIDLE in SWSUP only in active ARM: OMAP2+: hwmod: Fix sidle programming in _enable_sysc()/_idle_sysc() arm: mvebu: fix the 'ranges' property to handle PCIe ARM: mvebu: select ARCH_REQUIRE_GPIOLIB for mvebu platform ARM: AM33XX: Add missing .clkdm_name to clkdiv32k_ick clock ...
2013-05-24Merge tag 'sunxi-fixes-for-3.10' of git://github.com/mripard/linux into fixesOlof Johansson
From Maxime Ripard: Small set of fixes for 3.10: - Fix build breakage in pinctrl driver when no other architecture is selected - Fix Mini X-plus device tree build * tag 'sunxi-fixes-for-3.10' of git://github.com/mripard/linux: ARM: sunxi: select ARCH_REQUIRE_GPIOLIB ARM: sunxi: Fix Mini X-plus device tree build Signed-off-by: Olof Johansson <olof@lixom.net>
2013-05-24ARM: SAMSUNG: Add names to fimd0 IRQ resourcesTomasz Figa
Since commit 1977e6d8 (drm/exynos: change the method for getting the interrupt) the Exynos DRM FIMD driver requires IRQ resources to be named. This patch fixes probe failure in non-DT cases by adding appropriate resource names to fimd0 platform device. Signed-off-by: Tomasz Figa <t.figa@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
2013-05-24ARM: EXYNOS: fix software reset logic for EXYNOS5440 SOCJungseok Lee
This patch fixes software reset logic. Software reset applies only to powered-on domains in SOC because software reset to all domains causes reboot failure. Signed-off-by: Jungseok Lee <jays.lee@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
2013-05-24ARM: EXYNOS: Fix support of Exynos4210 rev0 SoCTomasz Figa
This patch extends exynos_init_time() function to handle Exynos4210 rev0 SoC, which differs in availability of system timers and needs different clocksource initialization. This makes it possible to use exynos_init_time() function as init_time callback for all Exynos-based boards, including Universal_C210, which originally had to use samsung_timer_init(). Signed-off-by: Tomasz Figa <t.figa@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
2013-05-24Merge tag 'at91-fixes' of git://github.com/at91linux/linux-at91 into fixesOlof Johansson
From Nicolas Ferre: - One definition fix that can lead to mis-clock some AT91 peripherals on SAMA5. - Two DT related fixes. * tag 'at91-fixes' of git://github.com/at91linux/linux-at91: ARM: at91/sama5: fix incorrect PMC pcr div definition ARM: at91/dt: fix macb pinctrl_macb_rmii_mii_alt definition ARM: at91: at91sam9n12: move external irq declatation to DT Signed-off-by: Olof Johansson <olof@lixom.net>
2013-05-24ARM: at91/sama5: fix incorrect PMC pcr div definitionJosh Wu
Signed-off-by: Josh Wu <josh.wu@atmel.com> Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2013-05-24ARM: at91/dt: fix macb pinctrl_macb_rmii_mii_alt definitionBoris BREZILLON
The PA24 pin is wrongly assigned to peripheral B. In the current config there is 2 ETX3 pins (PA11 and PA24) and no ETXER pin (PA22). Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Cc: stable <stable@vger.kernel.org> # 3.8+
2013-05-24ARM: at91: at91sam9n12: move external irq declatation to DTJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2013-05-24ARM: dts: imx: fix clocks for cspiJonas Andersson
The CSPI controller has only one clock, but the driver spi-imx.c needs clock "per" to calculate bitrate divisor. Signed-off-by: Jonas Andersson <jonas@microbit.se> Acked-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-05-23Merge tag 'usb-3.10-rc2' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb Pull USB fixes from Greg Kroah-Hartman: "Here are a number of tiny USB bugfixes / new device ids for 3.10-rc2 The majority of these are USB gadget fixes, but they are all small. Other than that, some USB host controller fixes, and USB serial driver fixes for problems reported with them. Also hopefully a fixed up USB_OTG Kconfig dependancy, that one seems to be almost impossible to get right for all of the different platforms these days." * tag 'usb-3.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (56 commits) USB: cxacru: potential underflow in cxacru_cm_get_array() USB: ftdi_sio: Add support for Newport CONEX motor drivers USB: option: add device IDs for Dell 5804 (Novatel E371) WWAN card usb: ohci: fix goto wrong tag in err case usb: isp1760-if: fix memleak when platform_get_resource fail usb: ehci-s5p: fix memleak when fallback to pdata USB: serial: clean up chars_in_buffer USB: ti_usb_3410_5052: fix chars_in_buffer overhead USB: io_ti: fix chars_in_buffer overhead USB: ftdi_sio: fix chars_in_buffer overhead USB: ftdi_sio: clean up get_modem_status USB: serial: add generic wait_until_sent implementation USB: serial: add wait_until_sent operation USB: set device dma_mask without reference to global data USB: Blacklisted Cinterion's PLxx WWAN Interface usb: option: Add Telewell TW-LTE 4G USB: EHCI: remove bogus #error USB: reset resume quirk needed by a hub USB: usb-stor: realtek_cr: Fix compile error usb, chipidea: fix link error when USB_EHCI_HCD is a module ...
2013-05-23ARM i.MX6q: fix for ldb_di_selsJiada Wang
As pll5_video_div has been introduced to represent the clock generated from post-divider for video. Instead of pll5_video, pll5_video_div should be proper root clock for ldb_di_sel. Signed-off-by: Jiada Wang <jiada_wang@mentor.com> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-05-22ARM: 7729/1: vfp: ensure VFP_arch is non-zero when VFP is not supportedWill Deacon
Commit d3f79584a8b5 ("ARM: cleanup undefined instruction entry code") improved the register scheduling when handling undefined instructions. A side effect of this is that r5 is now used as a temporary, whilst the VFP probing code relies on r5 containing a non-zero value when VFP is not supported. This patch fixes the VFP detection code so that we don't rely on the contents of r5. Without this patch, Linux dies loudly on CPUs without VFP support. Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2013-05-22ARM: 7727/1: remove the .vm_mm value from gate_vmaSteven Capper
If one reads /proc/$PID/smaps, the mmap_sem belonging to the address space of the task being examined is locked for reading. All the pages of the vmas belonging to the task's address space are then walked with this lock held. If a gate_vma is present in the architecture, it too is examined by the fs/proc/task_mmu.c code. As gate_vma doesn't belong to the address space of the task though, its pages are not walked. A recent cleanup (commit f6604efe) of the gate_vma initialisation code set the vm_mm value to &init_mm. Unfortunately a non-NULL vm_mm value in the gate_vma will cause the task_mmu code to attempt to walk the pages of the gate_vma (with no mmap-sem lock held). If one enables Transparent Huge Page support and vm debugging, this will then cause OOPses as pmd_trans_huge_lock is called without mmap_sem being locked. This patch removes the .vm_mm value from gate_vma, restoring the original behaviour of the task_mmu code. Signed-off-by: Steve Capper <steve.capper@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2013-05-22ARM: 7723/1: crypto: sha1-armv4-large.S: fix SP handlingArd Biesheuvel
Make the SHA1 asm code ABI conformant by making sure all stack accesses occur above the stack pointer. Origin: http://git.openssl.org/gitweb/?p=openssl.git;a=commit;h=1a9d60d2 Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Acked-by: Nicolas Pitre <nico@linaro.org> Cc: stable@vger.kernel.org Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2013-05-22Merge tag 'renesas-boards-marzen-fixes-for-v3.10' of ↵Olof Johansson
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes From Simon Horman: Correct USB PHY initialisation on the marzen board. * tag 'renesas-boards-marzen-fixes-for-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: ARM: shmobile: marzen: Use error values in usb_power_* Signed-off-by: Olof Johansson <olof@lixom.net>
2013-05-22Merge tag 'omap-fixes-a-for-3.10-rc' of ↵Olof Johansson
git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into fixes From Paul Walmsley: Fix the OMAP serial driver to work correctly on OMAP4 when booting with DT. * tag 'omap-fixes-a-for-3.10-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending: ARM: OMAP2+: hwmod: Remove sysc slave idle and auto idle apis SERIAL: OMAP: Remove the slave idle handling from the driver ARM: OMAP2+: serial: Remove the un-used slave idle hooks ARM: OMAP2+: hwmod-data: UART IP needs software control to manage sidle modes ARM: OMAP2+: hwmod: Add a new flag to handle SIDLE in SWSUP only in active ARM: OMAP2+: hwmod: Fix sidle programming in _enable_sysc()/_idle_sysc() Signed-off-by: Olof Johansson <olof@lixom.net>
2013-05-22ARM: shmobile: marzen: Use error values in usb_power_*Simon Horman
This patch updates the marzen board code as if USB PHY isn't enabled they phy will have a value set by ERR_PTR() rather than be NULL. Without this patch a NULL pointer dereference and kernel panic occurs on initialisation of USB on marzen. This resolves a regression introduced in 3.10-rc1 by b7fa5c2aec5be083eb2719b405089703608e9bc6 ("usb: phy: return -ENXIO when PHY layer isn't enabled"). Tested-by: Nguyen Hong Ky <nh-ky@jinso.co.jp> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2013-05-21ARM: smp: Drop RCU_NONIDLE usage in cpu_die()Stephen Boyd
Before f7b861b7a6d9 ("arm: Use generic idle loop") ARM would kill the CPU within the rcu idle section. Now that the rcu_idle_enter()/exit() pair have been pushed lower down in the idle loop this is no longer true and so using RCU_NONIDLE here is no longer necessary and also harmful because RCU is not actually idle at this point. Cc: Russell King <linux@arm.linux.org.uk> Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-05-21ARM: tegra: defconfig fixesAlexandre Courbot
The AK8975 Kconfig option was renamed during the 3.10 merge window. Adjust tegra_defconfig to enable the new name, so it's not missing useful features. Tegra DRM support used to be enabled in the default Tegra configuration, but it now depends on CONFIG_TEGRA_HOST1X which is disabled by default. Enable CONFIG_TEGRA_HOST1X so that DRM support is compiled in again. Signed-off-by: Alexandre Courbot <acourbot@nvidia.com> [swarren, squashed Alex's and my changes together] Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Olof Johansson <olof@lixom.net>
2013-05-21ARM: nomadik: fix IRQ assignment for SMC ethernetLinus Walleij
The assignment of IRQ for the SMC91x ethernet adapter had two problems making it non-working: - It was not put into the ethernet device node. Let's do this by using the board-specific overlay, so we can make other overlays on other Nomadik boards. - The IRQ number was actually completely wrong, this was the number for NHK8815, not S8815. After this ethernet starts working on the USB S8815. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Olof Johansson <olof@lixom.net>
2013-05-21Merge tag 'ux500-arm-soc-v3.10-fixes' of ↵Olof Johansson
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into fixes From Linus Walleij, some ux500 fixes for the v3.10-rc series: - Fixes up the debug UART - Fix dangerous platform data double-assignment - Fix auxdata for the ethernet device - Select REGULATOR to satisfy Kconfig * tag 'ux500-arm-soc-v3.10-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson: ARM: ux500: select REGULATOR ARM: ux500: Provide device enumeration number suffix for SMSC911x ARM: ux500: Fix incorrect DEBUG UART virtual addresses ARM: ux500: Remove duplicated assignment of ab8500_platdata Signed-off-by: Olof Johansson <olof@lixom.net>
2013-05-21Merge tag 'imx-fixes-3.10' of git://git.linaro.org/people/shawnguo/linux-2.6 ↵Olof Johansson
into fixes From Shawn Guo, imx fixes for 3.10: - A few imx6 clock fixes. Nothing is extremely important, but since we're still in early -rc, I send them for 3.10 inclusion. - Having bootloader handle ARM errata, we will need to replicate the diagnostic register of boot cpu into secondary cores, since bootloader only sets up boot cpu. Otherwise, errata workaround simply does not work. * tag 'imx-fixes-3.10' of git://git.linaro.org/people/shawnguo/linux-2.6: ARM: imx: fix typo in gpu3d_shader_sels ARM: imx: replicate the diagnostic register of boot cpu into secondary cores ARM i.MX6: correct MLB clock configuration ARM i.MX6q: Fix periph_clk2_sel and periph2_clk2_sel clocks Signed-off-by: Olof Johansson <olof@lixom.net>
2013-05-21Merge tag 'fixes-3.10-2' of git://git.infradead.org/users/jcooper/linux into ↵Olof Johansson
fixes From Jason Cooper, mvebu fixes for v3.10 (round 2): - mvebu (and orion SoCs) - remove init_dma_coherent_pool_size() - mvebu - fix ranges DT property - fix DT reg value for L2 cache - select ARCH_REQUIRE_GPIOLIB - orion legacy - fix num_resources and id for ge10 and ge11 * tag 'fixes-3.10-2' of git://git.infradead.org/users/jcooper/linux: ARM: dts: mvebu: Fix wrong the address reg value for the L2-cache node ARM: plat-orion: Fix num_resources and id for ge10 and ge11 arm: mvebu: fix the 'ranges' property to handle PCIe ARM: mvebu: select ARCH_REQUIRE_GPIOLIB for mvebu platform ARM: mvebu: Fix ranges entry on XP GP board ARM: Orion: Remove redundant init_dma_coherent_pool_size() Signed-off-by: Olof Johansson <olof@lixom.net>
2013-05-21Merge tag 'omap-for-v3.10-rc1/fixes' of ↵Olof Johansson
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes From Tony Lindgren, fixes for omaps: - a section mismatch fix for hwmod - boot fix for omap2plus_defconfig for omap2 - musb interrupt fix when using device tree - am33xx clock fix that I missed earlier somehow - omap1 dma return code error fix * tag 'omap-for-v3.10-rc1/fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: ARM: AM33XX: Add missing .clkdm_name to clkdiv32k_ick clock ARM: OMAP2+: Add missing CONFIG_ARCH_MULTI_V6=y to omap2plus_defconfig ARM: OMAP: fix error return code in omap1_system_dma_init() ARM: OMAP: fix __init section mismatch for _enable_preprogram ARM: dts: Fix musb interrupt for device tree booting Signed-off-by: Olof Johansson <olof@lixom.net>
2013-05-21ARM: vt8500: Add missing NULL terminator in dt_compatSrinivas Kandagatla
When I tried booting a stih415 Dual core A9 with multi_v7_defconfig, it failed to boot. The issues seems to be changing by enabling or disabling VT8550 platform. Having a quick look at dt_compat list, it seems to miss a NULL terminator, which means of_flat_dt_match will compat check will cross the boundary of dt_compat and fault at some point , which is what was happening in my case. Without this patch if we try to boot multi_v7_defconfig you might notice that some of the platforms might fault if they fall after vt8500 in machine-desc list. Other platforms which fall before vt8500 in mdesc list will not fault. Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com> Acked-by: Tony Prisk <linux@prisktech.co.nz> Signed-off-by: Olof Johansson <olof@lixom.net>