| Age | Commit message (Collapse) | Author |
|---|
|
The SP804 driver statically initialises the cpumask of the clock event
device to be cpu_all_mask, which is derived from the compile-time
constant NR_CPUS. This breaks SMP_ON_UP systems where the interrupt
controller handling the sp804 doesn't have the irq_set_affinity callback
on the irq_chip, because the common timer code fails to identify the
device as cpu-local and ends up treating it as a broadcast device
instead.
This patch fixes the problem by using cpu_possible_mask at runtime,
which will correctly represent the possible CPUs when SMP_ON_UP is being
used.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Remove the unused regs-mem.h file
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
With device tree support enabled for dwmci controller, the unused
non-dt support for dwmci controller can be removed.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
[kgene.kim@samsung.com: updated as per Seungwon Jeon's pointing out]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
SPEAr is an ARM based family of SoCs. This patch adds in support of cpufreq
driver for SPEAr SoCs. It is supported via DT only and so bindings are present
in binding document.
Signed-off-by: Deepak Sikri <deepak.sikri@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Pull ARM fixes from Russell King:
"Not much here, just a couple minor/cosmetic fixes and a patch for the
decompressor which fixes problems with modern GCC and CPUs."
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7583/1: decompressor: Enable unaligned memory access for v6 and above
ARM: 7572/1: proc-v6.S: fix comment
ARM: 7570/1: quiet down the non make -s output
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator into next/cleanup
From Linus Walleij <linus.walleij@linaro.org>:
This series will do the following:
- Switch the Integrator/AP and /CP to use the SoC bus
when booting from device tree.
- Group all devices on the SoC below this bus so as to
set a good example of how to do this. The bus was
invented by Lee Jones, let's show how it's to be used
on a DT:ed SoC.
- Fetch the special system controller offsets from two
special device tree nodes for each case and replace
the static mappings with these at boot.
- Move some static remaps to the ATAG-only code path
and delete some static maps that aren't used.
- Push dependencies on system controller remaps down
to the Integrator/AP board file and the PCIv3 driver
respectively and use only dynamic remappings.
- Fix up conditional BUG() usage in the PCIv3 driver
to be simpler and more to the point.
* tag 'integrator-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator:
ARM: integrator: use BUG_ON where possible
ARM: integrator: push down SC dependencies
ARM: integrator: delete static UART1 mapping
ARM: integrator: delete SC mapping on the CP
ARM: integrator: remove static CP syscon mapping
ARM: integrator: remove static AP syscon mapping
ARM: integrator: hook the CP into the SoC bus
ARM: integrator: hook the AP into the SoC bus
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Correct option should be LEDS_TRIGGERS, not LEDS_TRIGGER.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The kvm_seq value has nothing to do what so ever with this other KVM.
Given that KVM support on ARM is imminent, it's best to rename kvm_seq
into something else to clearly identify what it is about i.e. a sequence
number for vmalloc section mappings.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
git://git.infradead.org/users/jcooper/linux into next/cleanup
From Jason Cooper:
orion cleanup for v3.8
- remove unused includes in kirkwood
- fix sparse warnings in kirkwood
- checkpatch cleanup in kirkwood
- use common code in pcie on kirkwood
* tag 'orion_cleanup_for_3.8' of git://git.infradead.org/users/jcooper/linux:
ARM: Kirkwood: Use hw_pci.ops instead of hw_pci.scan
ARM: Kirkwood: checkpatch cleanups
ARM: Kirkwood: Fix sparse warnings.
ARM: Kirkwood: Remove unused includes
ARM: kirkwood: cleanup lsxl board includes
|
|
next/fixes-non-critical
From Haojian Zhuang:
* 'armsoc/fix' of git://github.com/hzhuang1/linux:
ARM: pxa: add dummy SA1100 rtc clock in pxa25x
|
|
git://git.infradead.org/users/jcooper/linux into fixes
From Jason Cooper:
orion fixes for v3.7
- dove irq fix
- kirkwood pcie fix
* tag 'orion_fixes_for_3.7' of git://git.infradead.org/users/jcooper/linux:
ARM: Kirkwood: Update PCI-E fixup
Dove: Fix irq_to_pmu()
Dove: Attempt to fix PMU/RTC interrupts
|
|
Merging in mainline back to next/cleanup since it has collected a few
conflicts between fixes going upstream and some of the cleanup patches.
Git doesn't auto-resolve some of them, and they're mostly noise so let's
take care of it locally.
Conflicts are in:
arch/arm/mach-omap2/omap_hwmod_44xx_data.c
arch/arm/plat-omap/i2c.c
drivers/video/omap2/dss/dss.c
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.pengutronix.de/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"Bugfixes for the i2c subsystem.
Except for a few one-liners, there is mainly one revert because of an
overlooked dependency. Since there is no linux-next at the moment, I
did some extra testing, and all was fine for me."
* 'i2c-embedded/for-current' of git://git.pengutronix.de/git/wsa/linux:
i2c: mxs: Handle i2c DMA failure properly
i2c: s3c2410: Fix code to free gpios
i2c: omap: ensure writes to dev->buf_len are ordered
Revert "ARM: OMAP: convert I2C driver to PM QoS for MPU latency constraints"
i2c: at91: fix SMBus quick command
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull one more ARM SoC fix from Olof Johansson:
"I missed one pull request from Samsung with one fix in the previous
batch. Here it is -- a dma driver fix for an early version of silicon
that they still support."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: EXYNOS: PL330 MDMA1 fix for revision 0 of Exynos4210 SOC
|
|
Modern GCC can generate code which makes use of the CPU's native
unaligned memory access capabilities. This is useful for the C
decompressor implementations used for unpacking compressed kernels.
This patch disables alignment faults and enables the v6 unaligned
access model on CPUs which support these features (i.e., v6 and
later), allowing full unaligned access support for C code in the
decompressor.
The decompressor C code must not be built to assume that unaligned
access works if support for v5 or older platforms is included in
the kernel.
For correct code generation, C decompressor code must always use
the get_unaligned and put_unaligned accessors when dealing with
unaligned pointers, regardless of this patch.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
If a kernel is configured with a DT containing more /cpu nodes than
nr_cpu_ids, the number of cpus must be capped in the DT parsing
code. Current code carries out the check, but fails to cap the
value and the check is executed after the cpu logical index is used,
which can lead to memory corruption due to index overflow.
This patch refactors the check against nr_cpu_ids and move it before
any computed index is used in the parsing code.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Reported-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Commit e50c541 (ARM: perf: add guest vs host discrimination) broken the
link as perf_instruction_pointer and perf_misc_flags are not defined
when CONFIG_HW_PERF_EVENTS is not selected.
As it make little sense to try and profile a guest without any HW event,
just fallback to the original code when this config option is not selected.
Reported-by: Russell King <linux@arm.linux.org.uk>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
* fix failure seen on Zaurus corgi:
* sa1100-rtc sa1100-rtc: failed to find rtc clock source
* sa1100-rtc: probe of sa1100-rtc failed with error -2
Signed-off-by: Andrea Adami <andrea.adami@gmail.com>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input updates from Dmitry Torokhov:
"This fixes recent regression where /dev/input/mice got assigned wrong
device node which messed up setups with static /dev, and a regression
in ads7846 GPIO debounce setup."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
ARM - OMAP: ads7846: fix pendown debounce setting
Input: ads7846 - enable pendown GPIO debounce time setting
Input: mousedev - move /dev/input/mice to the correct minor
Input: MT - document new 'flags' argument of input_mt_init_slots()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes
From Kukjin Kim:
Here is Samsung fixes for v3.7 and it is for fixing of mdma1 address
for exynos4210 rev0 SoC.
* 'v3.7-samsung-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: PL330 MDMA1 fix for revision 0 of Exynos4210 SOC
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The ixp4xx queue manager uses "const struct qmgr_regs __iomem *" as the
type for a pointer that is passed to __raw_writel, which is not
allowed because of the const-ness.
Dropping the 'const' keyword fixes the problem. While we're here,
let's also drop the useless type cast.
Without this patch, building ixp4xx_defconfig results in:
In file included from arch/arm/mach-ixp4xx/ixp4xx_qmgr.c:15:0:
arch/arm/mach-ixp4xx/include/mach/qmgr.h: In function 'qmgr_put_entry':
arch/arm/mach-ixp4xx/include/mach/qmgr.h:96:2: warning: passing argument 2 of '__raw_writel' discards 'const' qualifier from pointer target type [enabled by default]
arch/arm/include/asm/io.h:88:91: note: expected 'volatile void *' but argument is of type 'const u32 *'
In file included from drivers/net/ethernet/xscale/ixp4xx_eth.c:41:0:
arch/arm/mach-ixp4xx/include/mach/qmgr.h: In function 'qmgr_put_entry':
arch/arm/mach-ixp4xx/include/mach/qmgr.h:96:2: warning: passing argument 2 of '__raw_writel' discards 'const' qualifier from pointer target type [enabled by default]
arch/arm/include/asm/io.h:88:91: note: expected 'volatile void *' but argument is of type 'const u32 *'
arch/arm/mach-ixp4xx/ixp4xx_qmgr.c: In function 'qmgr_set_irq':
arch/arm/mach-ixp4xx/ixp4xx_qmgr.c:41:9: warning: passing argument 2 of '__raw_writel' discards 'const' qualifier from pointer target type [enabled by default]
arch/arm/include/asm/io.h:88:91: note: expected 'volatile void *' but argument is of type 'const u32 *'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl>
|
|
Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl>
|
|
It doesn't make much sense to map QMgr dynamically - we almost always need it
and the static mapping will be needed for little-endian data-coherent operation
(to make QMgr region value-coherent).
Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl>
|
|
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Cc: Imre Kaloz <kaloz@openwrt.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl>
|
|
Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl>
|
|
Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl>
|
|
Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl>
|
|
linux/videodev2.h was included twice.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
From Tony Lindgren:
Few more regression fixes related to u-boot only muxing
essential pins.
* tag 'omap-for-v3.7-rc5/fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP4: TWL: mux sys_drm_msecure as output for PMIC
ARM: OMAP3: igep0020: Set WIFI/BT GPIO pins in correct mux mode
ARM: OMAP: Add maintainer entry for IGEP machines
|
|
Commit 97ee9f01 (ARM: OMAP: fix the ads7846 init code) have enabled the
pendown GPIO debounce time setting by the below sequence:
gpio_request_one()
gpio_set_debounce()
gpio_free()
It also revealed a bug in the OMAP GPIO handling code which prevented
the GPIO debounce clock to be disabled and CORE transition to low power
states.
Commit c9c55d9 (gpio/omap: fix off-mode bug: clear debounce settings on
free/reset) fixes the OMAP GPIO handling code by making sure that the
GPIO debounce clock gets disabled if no GPIO is requested from current
bank.
While fixing the OMAP GPIO handling code (in the right way), the above
commit makes the gpio_request->set_debounce->free sequence invalid as
after freeing the GPIO, the debounce settings are lost.
Fix the debounce settings by moving the debounce initialization to the
actual GPIO requesting code - the ads7846 driver.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The kirkwood_pcie_scan_bus function duplicates the common code in
bios32.c, passing ops in will use the common code..
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
The ARM IM-PD1 add-on module has a few clock of its own, let's
move also these down to the drivers/clk/versatile driver dir
and get rid of any remaining oldschool Integrator clocks.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
- The code relies on rc_pci_fixup being called, which only happens
when CONFIG_PCI_QUIRKS is enabled, so add that to Kconfig. Omitting
this causes a booting failure with a non-obvious cause.
- Update rc_pci_fixup to set the class properly, copying the
more modern style from other places
- Correct the rc_pci_fixup comment
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
PMU interrupts start at IRQ_DOVE_PMU_START, not IRQ_DOVE_PMU_START + 1.
Fix the condition. (It may have been less likely to occur had the code
been written "if (irq >= IRQ_DOVE_PMU_START" which imho is the easier
to understand notation, and matches the normal way of thinking about
these things.)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: stable@vger.kernel.org
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
Fix the acknowledgement of PMU interrupts on Dove: some Dove hardware
has not been sensibly designed so that interrupts can be handled in a
race free manner. The PMU is one such instance.
The pending (aka 'cause') register is a bunch of RW bits, meaning that
these bits can be both cleared and set by software (confirmed on the
Armada-510 on the cubox.)
Hardware sets the appropriate bit when an interrupt is asserted, and
software is required to clear the bits which are to be processed. If
we write ~(1 << bit), then we end up asserting every other interrupt
except the one we're processing. So, we need to do a read-modify-write
cycle to clear the asserted bit.
However, any interrupts which occur in the middle of this cycle will
also be written back as zero, which will also clear the new interrupts.
The upshot of this is: there is _no_ way to safely clear down interrupts
in this register (and other similarly behaving interrupt pending
registers on this device.) The patch below at least stops us creating
new interrupts.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: stable@vger.kernel.org
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
cm-t3517 starting from revision 1.2 does not have the 32K oscilator
wired to the AM3517 SoC.
Therefore switch to use the GPTIMER for system clock.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
CONFIG_OMAP_32K_TIMER is kind of standing on the single zImage way.
Make OMAP2+ timer code independant from the CONFIG_OMAP_32K_TIMER
setting.
To remove the dependancy, several conversions/additions had to be done:
1) Timer initialization functions are named by the platform
name and the clock source in use.
This also makes it possible to define and use the GPTIMER as the
clock source instead of the 32K timer on platforms that do not have
the 32K timer ip block or the 32K timer is not wired on the board.
Currently, the the timer is chosen in the machine_desc structure on
per board basis. Later, DT should be used to choose the timer.
2) Settings under the CONFIG_OMAP_32K_TIMER option are used as defaults
and those under !CONFIG_OMAP_32K_TIMER are removed.
This removes the CONFIG_OMAP_32K_TIMER on OMAP2+ timer code.
3) Since we have all the timers defined inside machine_desc structure
and we no longer need the fallback to gp_timer clock source in case
32k_timer clock source is unavailable (namely on AM33xx), we no
longer need the #ifdef around omap2_sync32k_clocksource_init()
function. Remove the #ifdef CONFIG_OMAP_32K_TIMER around the
omap2_sync32k_clocksource_init() function.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Cc: Jon Hunter <jon-hunter@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Vaibhav Hiremath <hvaibhav@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Jon Hunter <jon-hunter@ti.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/cleanup
From Kukjin Kim:
* 'next/cleanup-samsung-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: SAMSUNG: use devm_ functions for ADC driver
ARM: EXYNOS: no duplicate mask/unmask in eint0_15
ARM: S3C24XX: SPI clock channel setup is fixed for S3C2443
ARM: EXYNOS: Remove i2c0 resource information and setting of device names
ARM: S3C64XX: Statically define parent clock of "camera" clock
ARM: S3C64XX: Remove duplicated camera clock
ARM: EXYNOS: Add missing static storage class specifiers in clock-exynos5.c
ARM: EXYNOS: Make combiner_of_init function static
ARM: EXYNOS: Make s3c_device_i2c0 always use id 0
ARM: EXYNOS: Remove wrongly placed usb2.0 PHY_CFG definition from PMU_REG
ARM: EXYNOS: reorder inclusions of <linux/platform_data/xxx.h>
ARM: EXYNOS: Remove unused static uart resource information
ARM: EXYNOS: Remove static io-remapping for gic and combiner
ARM: EXYNOS: Remove wrong I2S0 clock from peril clock
ARM: EXYNOS: remove the MMC_CAP2_BROKEN_VOLTAGE
|
|
chan->end is tested for being NULL. However in the event that it is NULL, the
subsequent assignment statement would lead to NULL pointer dereference.
Thus dereferencing it only when it is not NULL.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-rpi into next/cleanup
From Stephen Warren:
ARM: bcm2835: cleanup
Just a few minor/trivial cleanups.
* tag 'bcm2835-for-3.8-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-rpi:
ARM: bcm2835: remove useless variables from Makefile.boot
ARM: bcm2835: Fix typo in the error message
ARM: bcm2835: Add missing static modifiers
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/cleanup
From Stephen Warren:
ARM: tegra: cleanup for 3.8
Various trivial cleanup changes of the Tegra code for 3.8.
Many of the changes simply remove useless #include statements, which
enable those headers to be removed or moved later, as work towards
multi-platform zImage support.
<mach/{iram,io}map.h> are moved up to arch/arm/mach-tegra to prevent
any new code outside mach-tegra from using them.
Finally, the regulator definitions in all board device tree files are
updated to use the new simpler syntax that was agreed upon.
* tag 'tegra-for-3.8-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
ARM: tegra: move irammap.h to mach-tegra
ARM: tegra: move iomap.h to mach-tegra
ARM: tegra: remove <mach/dma.h>
ARM: tegra: move tegra-ahb.h out of arch/arm/mach-tegra/
ARM: tegra: remove unnecessary includes of <mach/*.h>
iommu: tegra: remove include of <mach/iomap.h>
staging: nvec: remove include of <mach/iomap.h>
crypto: tegra: remove include of <mach/clk.h>
ARM: tegra: update *.dts for regulator-compatible deprecation
usb: phy: tegra remove include of <mach/iomap.h>
usb: host: tegra remove include of <mach/iomap.h>
|
|
next/fixes-non-critical
From Haojian Zhuang:
* 'armsoc/fix' of git://github.com/hzhuang1/linux:
ARM: pxa: fix pxa25x gpio wakeup setting
+ Linux 3.7-rc6
|
|
Let's stop spawning the pinctrl driver from the GPIO driver,
we have these two mechanisms broken apart now, and they can
each probe in isolation. If the GPIO driver cannot find its
pin controller (pinctrl-u300), the pin controller core will
tell it to defer probing.
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
into next/cleanup
From Nicolas Ferre:
Removing unneeded macro.
* tag 'at91-for-next-cleanup' of git://github.com/at91linux/linux-at91:
ARM: at91/atmel-mci: remove unused setup_dma_addr() macro
|
|
next/headers
From Nicolas Ferre:
One fix related to UART for the "headers move" branch
* tag 'at91-header' of git://github.com/at91linux/linux-at91:
atmel: move ATMEL_MAX_UART to platform_data/atmel.h
|
|
* Since 3.3 gpio wakeup is broken on pxa25x (tested on corgi and poodle).
* Use gpio_set_wake like done for pxa27x with commit id
* b95ace54a23e2f8ebb032744cebb17c9f43bf651
Signed-off-by: Andrea Adami <andrea.adami@gmail.com>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
|
|
A couple devices' DT compatible values only contained the device name
without any vendor prefix. Add the missing vendor prefixes.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
|
|
|
|
into devel-stable
|
