| Age | Commit message (Collapse) | Author |
|---|
|
Driving resets from libsas-eh is pre-mature as libata will make a
decision about performing a softreset. Currently libata determines
whether to perform a softreset based on ata_eh_followup_srst_needed(),
and none of those conditions apply to isci.
Remove the srst implementation and translate ->lldd_lu_reset() for ata
devices as a request to drive a reset via libata-eh.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
The commands that timeout when a disk is forcibly removed may trigger
libata to attempt recovery of the device. If libsas has decided to
remove the device don't permit ata to continue to issue resets to its
last known phy.
The primary motivation for this patch is hotplug testing by writing 0 to
/sys/class/sas_phy/phyX/enable. Without this check this test leads to
libata issuing a reset and re-enabling the device that wants to be torn
down.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
In the direct-attached case this routine returns the phy on which this
device was first discovered. Which is broken if we want to support
wide-targets, as this phy reference can become stale even though the
port is still active.
In the expander-attached case this routine tries to lookup the phy by
scanning the attached sas addresses of the parent expander, and BUG_ONs
if it can't find it. However since eh and the libsas workqueue run
independently we can still be attempting device recovery via eh after
libsas has recorded the device as detached. This is even easier to hit
now that eh is blocked while device domain rediscovery takes place, and
that libata is fed more timed out commands increasing the chances that
it will try to recover the ata device.
Arrange for dev->phy to always point to a last known good phy, it may be
stale after the port is torn down, but it will catch up for wide port
reconfigurations, and never be NULL.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
No sense in issuing or retrying commands to an expander that has been
removed.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Commit 56dd2c06 "[SCSI] libsas: Don't issue commands to devices that
have been hot-removed" marked the parent device of an end-device as gone
when all the phys to the end device have been deleted.
The expander device is still present until its parent is removed. This
is a benign change until the smp_execute_task() path is taught to check
->gone.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Use ata_wait_after_reset() to poll for link recovery after a reset.
This combined with sas_ha->eh_mutex prevents expander rediscovery from
probing phys in an intermediate state. Local discovery does not have a
mechanism to filter link status changes during this timeout, so it
remains the responsibility of lldds to prevent premature port teardown.
Although once all lldd's support ->lldd_ata_check_ready() that could be
used as a gate to local port teardown.
The signature fis is re-transmitted when the link comes back so we
should be revalidating the ata device class, but that is left to a future
patch.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Once sas_ata_hard_reset() starts honoring the 'deadline' parameter a
pathological configuration could take 25 seconds per ata device
(serialized) to recover. Run per-port recoveries in parallel.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
SAS does not tag SMP requests, and at least one lldd (isci) does not permit
more than one in-flight request at a time.
[jejb: fix sas_init_dev tab issues while we're at it]
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
In the case of an explicit sas_phy_enable call to disable a phy,
the LLDD provides the calls to sas_phy_disconnected and the
PHYE_LOSS_OF_SIGNAL event.
NOTE: This assumes that the lldd(s) generate the notification, which
appears to be the case, but only verfied on isci.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Execute the link-reset triggered by sas_phy_enable via
transport_sas_phy_reset so that it can be managed by libata.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Link resets leave ata affiliations intact, so arrange for libsas to make
an effort to avoid dropping the device due to a slow-to-recover link.
Towards this end carry out reset in the host workqueue so that it can
check for ata devices and kick the reset request to libata. Hard
resets, in contrast, bypass libata since they are meant for associating
an ata device with another initiator in the domain (tears down
affiliations).
Need to add a new transport_sas_phy_reset() since the current
sas_phy_reset() is a utility function to libsas lldds. They are not
prepared for it to loop back into eh.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Extend the sas transport class to allow transport users to attach extra
data to a sas_phy (->hostdata). Use this area in libsas to move resets
to workq context in preparation for scheduling ata device resets through
libata-eh.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Since sata devices can take several seconds to recover the link on reset
the 0.5 seconds that libsas currently waits may not be enough. Instead
if we are rediscovering a phy that was previously attached to a sata
device let libata handle any resets to encourage the device to transmit
the initial fis.
Once sas_ata_hard_reset() and lldds learn how to honor 'deadline' libsas
should stop encountering phys in an intermediate state, until then this
will loop until the fis is transmitted or ->attached_sas_addr gets
cleared, but in the more likely initial discovery case we keep existing
behavior.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
lldds use the SAS_TASK_NEED_DEV_RESET interface to request that eh
perform a reset. In the sata device case defer the commands that
triggered the reset to libata-eh context so it can perform its pre and
post reset management.
In the sas_ata_post_internal() case the reset request is falling on deaf
ears as the sas_task is immediately destroyed without any reset action.
Since it is currently a nop, and likely superfluous given the conversion
to new-style libata-eh, just drop the request.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
libsas-eh if it successfully aborts an ata command will hide the timeout
condition (AC_ERR_TIMEOUT) from libata. The command likely completes
with the all-zero task->task_status it started with. Instead, interpret
a TMF_RESP_FUNC_COMPLETE as the end of the sas_task but keep the scmd
around for libata-eh to handle.
Tested-by: Andrzej Jakowski <andrzej.jakowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Until we have told the lldd to forget a task a timed out operation can
return from the hardware at any time. Since completion frees the task
we need to make sure that no tasks run their normal completion handler
once eh has decided to manage the task. Similar to
ata_scsi_cmd_error_handler() freeze completions to let eh judge the
outcome of the race.
Task collector mode is problematic because it presents a situation where
a task can be timed out and aborted before the lldd has even seen it.
For this case we need to guarantee that a task that an lldd has been
told to forget does not get queued after the lldd says "never seen it".
With sas_scsi_timed_out we achieve this with the ->task_queue_flush
mutex, rather than adding more time.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
We invoke task->task_done() to free the task in the eh case, but at this
point we are prepared for scsi_eh_flush_done_q() to finish off the scmd.
Introduce sas_end_task() to capture the final response status from the
lldd and free the task.
Also take the opportunity to kill this warning.
drivers/scsi/libsas/sas_scsi_host.c: In function ‘sas_end_task’:
drivers/scsi/libsas/sas_scsi_host.c:102:3: warning: case value ‘2’ not in enumerated type ‘enum exec_status’ [-Wswitch]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Since sas_ata does not implement ->freeze(), completions for scmds and
internal commands can still arrive concurrent with
ata_scsi_cmd_error_handler() and sas_ata_post_internal() respectively.
By the time either of those is called libata has committed to completing
the qc, and the ATA_PFLAG_FROZEN flag tells sas_ata_task_done() it has
lost the race.
In the sas_ata_post_internal() case we take on the additional
responsibility of freeing the sas_task to close the race with
sas_ata_task_done() freeing the the task while sas_ata_post_internal()
is in the process of invoking ->lldd_abort_task().
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Prior to the conversion to the new-style libata-eh sas_ata_task_done()
may have been the last opportunity to clean up the scmd, but now
libata-eh explicitly handles this case. It also races against sas-eh.
If a lldd completes a task after SAS_TASK_STATE_ABORTED is set it could
trigger a spurious decrement of shost->host_failed. Current lldds have
the band-aid of checking SAS_TASK_STATE_ABORTED before calling
->task_done(), but better to just let the scmds escalate to libata for
race free cleanup.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
sas_discover_sata() notifies lldds of sata devices twice. Once to allow
the 'identify' to be sent, and a second time to allow aic94xx (the only
libsas driver that cares about sata_dev.identify) to setup NCQ
parameters before the device becomes known to the midlayer. Replace
this double notification and intervening 'identify' with an explicit
->lldd_ata_set_dmamode notification. With this change all ata internal
commands are issued by libata, so we no longer need sas_issue_ata_cmd().
The data from the identify command only needs to be cached in one
location so ata_device.id replaces domain_device.sata_dev.identify.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
libata error handling provides for a timeout for link recovery. libsas
must not rescan for previously known devices in this interval otherwise
it may remove a device that is simply waiting for its link to recover.
Let libata-eh make the determination of when the link is stable and
prevent libsas (host workqueue) from taking action while this
determination is pending.
Using a mutex (ha->disco_mutex) to flush and disable revalidation while
eh is running requires any discovery action that may block on eh be
moved to its own context outside the lock. Probing ATA devices
explicitly waits on ata-eh and the cache-flush-io issued during device
removal may also pend awaiting eh completion. Essentially any rphy
add/remove activity needs to run outside the lock.
This adds two new cleanup states for sas_unregister_domain_devices()
'allocated-but-not-probed', and 'flagged-for-destruction'. In the
'allocated-but-not-probed' state dev->rphy points to a rphy that is
known to have not been through a sas_rphy_add() event. At domain
teardown check if this device is still pending probe and cleanup
accordingly. Similarly if a device has already been queued for removal
then sas_unregister_domain_devices has nothing to do.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
In preparation for adding tracking of another device state "destroy".
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Each libsas driver (mvsas, pm8001, and isci) has invented a different
method for managing the ap->lock. The lock is held by the ata
->queuecommand() path. mvsas drops it prior to acquiring any internal
locks which allows it to hold its internal lock across calls to
task->task_done(). This capability is important as it is the only way
the driver can flush task->task_done() instances to guarantee that it no
longer has any in-flight references to a domain_device at
->lldd_dev_gone() time.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
When an lldd invokes ->notify_port_event() it can trigger a chain of libsas
events to:
1/ form the port and find the direct attached device
2/ if the attached device is an expander perform domain discovery
A call to flush_workqueue() will only flush the initial port formation work.
Currently libsas users need to call scsi_flush_work() up to the max depth of
chain (which will grow from 2 to 3 when ata discovery is moved to its own
discovery event). Instead of open coding multiple calls switch to use
drain_workqueue() to flush sas work.
drain_workqueue() does not handle new work submitted during the drain so
libsas needs a bit of infrastructure to hold off unchained work submissions
while a drain is in flight. A lldd ->notify() event is considered 'unchained'
while a sas_discover_event() is 'chained'. As Tejun notes:
"For now, I think it would be best to add private wrapper in libsas to
support deferring unchained work items while draining."
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
In preparation for adding new states (SAS_HA_DRAINING, SAS_HA_FROZEN),
convert ha->state into a set of flags.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
The locks only served to make sure the pending event bitmask was updated
consistently.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
These are never freed in the nominal path. A domain_device has a
different lifetime than a sas_rphy we need a dev->rphy independent way
of identifying sata devices.
Reviewed-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Arrange for the deallocation of a struct domain_device object when it no
longer has:
1/ any children
2/ references by any scsi_targets
3/ references by a lldd
The comment about domain_device lifetime in
Documentation/scsi/libsas.txt is stale as it appears mainline never had
a version of a struct domain_device that was registered as a kobject.
We now manage domain_device reference counts on behalf of external
agents.
Reviewed-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Per commit 3e4ec344 "libata: kill ATA_FLAG_DISABLED" needing to set
ATA_DEV_NONE is a holdover from before libsas converted to the
"new-style" ata-eh.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Commit 1e34c838 "[SCSI] libsas: remove spurious sata control register
read/write" removed the routines to fake the presence of the sata
control registers, now remove the unused data structure fields to kill
any remaining confusion.
Acked-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
For the basic SCSI infrastructure files that are exporting symbols
but not modules themselves, add in the basic export.h header file
to allow the exports.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (204 commits)
[SCSI] qla4xxx: export address/port of connection (fix udev disk names)
[SCSI] ipr: Fix BUG on adapter dump timeout
[SCSI] megaraid_sas: Fix instance access in megasas_reset_timer
[SCSI] hpsa: change confusing message to be more clear
[SCSI] iscsi class: fix vlan configuration
[SCSI] qla4xxx: fix data alignment and use nl helpers
[SCSI] iscsi class: fix link local mispelling
[SCSI] iscsi class: Replace iscsi_get_next_target_id with IDA
[SCSI] aacraid: use lower snprintf() limit
[SCSI] lpfc 8.3.27: Change driver version to 8.3.27
[SCSI] lpfc 8.3.27: T10 additions for SLI4
[SCSI] lpfc 8.3.27: Fix queue allocation failure recovery
[SCSI] lpfc 8.3.27: Change algorithm for getting physical port name
[SCSI] lpfc 8.3.27: Changed worst case mailbox timeout
[SCSI] lpfc 8.3.27: Miscellanous logic and interface fixes
[SCSI] megaraid_sas: Changelog and version update
[SCSI] megaraid_sas: Add driver workaround for PERC5/1068 kdump kernel panic
[SCSI] megaraid_sas: Add multiple MSI-X vector/multiple reply queue support
[SCSI] megaraid_sas: Add support for MegaRAID 9360/9380 12GB/s controllers
[SCSI] megaraid_sas: Clear FUSION_IN_RESET before enabling interrupts
...
|
|
port->dev_list maintains a list of devices attached to a given sas root port.
It needs to be mutated under a lock as contexts outside of the
single-threaded-libsas-workqueue access the list via sas_find_dev_by_rphy().
Fixup locations where the list was being mutated without a lock.
This is a follow-up to commit 5911e963 "[SCSI] libsas: remove expander
from dev list on error", where Luben noted [1]:
> 2/ We have unlocked list manipulations in sas_ex_discover_end_dev(),
> sas_unregister_common_dev(), and sas_ex_discover_end_dev()
Yes, I can see that and that is very unfortunate.
[1]: http://marc.info/?l=linux-scsi&m=131480962006471&w=2
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
When a wide port is being utilized to a target, if one disables only one
of the
phys, we get an OS crash:
BUG: unable to handle kernel NULL pointer dereference at
0000000000000238
IP: [<ffffffff814ca9b1>] mutex_lock+0x21/0x50
PGD 4103f5067 PUD 41dba9067 PMD 0
Oops: 0002 [#1] SMP
last sysfs file: /sys/bus/pci/slots/5/address
CPU 0
Modules linked in: pm8001(U) ses enclosure fuse nfsd exportfs autofs4
ipmi_devintf ipmi_si ipmi_msghandler nfs lockd fscache nfs_acl
auth_rpcgss 8021q fcoe libfcoe garp libfc scsi_transport_fc stp scsi_tgt
llc sunrpc cpufreq_ondemand acpi_cpufreq freq_table ipv6 sr_mod cdrom
dm_mirror dm_region_hash dm_log uinput sg i2c_i801 i2c_core iTCO_wdt
iTCO_vendor_support e1000e mlx4_ib ib_mad ib_core mlx4_en mlx4_core ext3
jbd mbcache sd_mod crc_t10dif usb_storage ata_generic pata_acpi ata_piix
libsas(U) scsi_transport_sas dm_mod [last unloaded: pm8001]
Modules linked in: pm8001(U) ses enclosure fuse nfsd exportfs autofs4
ipmi_devintf ipmi_si ipmi_msghandler nfs lockd fscache nfs_acl
auth_rpcgss 8021q fcoe libfcoe garp libfc scsi_transport_fc stp scsi_tgt
llc sunrpc cpufreq_ondemand acpi_cpufreq freq_table ipv6 sr_mod cdrom
dm_mirror dm_region_hash dm_log uinput sg i2c_i801 i2c_core iTCO_wdt
iTCO_vendor_support e1000e mlx4_ib ib_mad ib_core mlx4_en mlx4_core ext3
jbd mbcache sd_mod crc_t10dif usb_storage ata_generic pata_acpi ata_piix
libsas(U) scsi_transport_sas dm_mod [last unloaded: pm8001]
Pid: 5146, comm: scsi_wq_5 Not tainted
2.6.32-71.29.1.el6.lustre.7.x86_64 #1 Storage Server
RIP: 0010:[<ffffffff814ca9b1>] [<ffffffff814ca9b1>]
mutex_lock+0x21/0x50
RSP: 0018:ffff8803e4e33d30 EFLAGS: 00010246
RAX: 0000000000000000 RBX: 0000000000000238 RCX: 0000000000000000
RDX: 0000000000000000 RSI: ffff8803e664c800 RDI: 0000000000000238
RBP: ffff8803e4e33d40 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000001 R12: 0000000000000000
R13: 0000000000000238 R14: ffff88041acb7200 R15: ffff88041c51ada0
FS: 0000000000000000(0000) GS:ffff880028200000(0000)
knlGS:0000000000000000
CS: 0010 DS: 0018 ES: 0018 CR0: 000000008005003b
CR2: 0000000000000238 CR3: 0000000410143000 CR4: 00000000000006f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process scsi_wq_5 (pid: 5146, threadinfo ffff8803e4e32000, task
ffff8803e4e294a0)
Stack:
ffff8803e664c800 0000000000000000 ffff8803e4e33d70 ffffffffa001f06e
<0> ffff8803e4e33d60 ffff88041c51ada0 ffff88041acb7200 ffff88041bc0aa00
<0> ffff8803e4e33d90 ffffffffa0032b6c 0000000000000014 ffff88041acb7200
Call Trace:
[<ffffffffa001f06e>] sas_port_delete_phy+0x2e/0xa0 [scsi_transport_sas]
[<ffffffffa0032b6c>] sas_unregister_devs_sas_addr+0xac/0xe0 [libsas]
[<ffffffffa0034914>] sas_ex_revalidate_domain+0x204/0x330 [libsas]
[<ffffffffa00307f0>] ? sas_revalidate_domain+0x0/0x90 [libsas]
[<ffffffffa0030855>] sas_revalidate_domain+0x65/0x90 [libsas]
[<ffffffff8108c7d0>] worker_thread+0x170/0x2a0
[<ffffffff81091ea0>] ? autoremove_wake_function+0x0/0x40
[<ffffffff8108c660>] ? worker_thread+0x0/0x2a0
[<ffffffff81091b36>] kthread+0x96/0xa0
[<ffffffff810141ca>] child_rip+0xa/0x20
[<ffffffff81091aa0>] ? kthread+0x0/0xa0
[<ffffffff810141c0>] ? child_rip+0x0/0x20
Code: ff ff 85 c0 75 ed eb d6 66 90 55 48 89 e5 48 83 ec 10 48 89 1c 24
4c 89 64 24 08 0f 1f 44 00 00 48 89 fb e8 92 f4 ff ff 48 89 df <f0> ff
0f 79 05 e8 25 00 00 00 65 48 8b 04 25 08 cc 00 00 48 2d
RIP [<ffffffff814ca9b1>] mutex_lock+0x21/0x50
RSP <ffff8803e4e33d30>
CR2: 0000000000000238
The following patch is admittedly a band-aid, and does not solve the
root cause, but it still is a good candidate for hardening as a pointer
check before reference.
Signed-off-by: Mark Salyzyn <mark_salyzyn@us.xyratex.com>
Tested-by: Jack Wang <jack_wang@usish.com>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Allow the sas-transport-class to update events for local phys via a new
PHY_FUNC_GET_EVENTS command to ->lldd_control_phy(). Fixup drivers that
are not prepared for new enum phy_func values, and unify
->lldd_control_phy() error codes.
These are the SAS defined phy events that are reported in a
smp-report-phy-error-log command:
* /sys/class/sas_phy/<phyX>/invalid_dword_count
* /sys/class/sas_phy/<phyX>/running_disparity_error_count
* /sys/class/sas_phy/<phyX>/loss_of_dword_sync_count
* /sys/class/sas_phy/<phyX>/phy_reset_problem_count
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Based on original implementation from Jiangbi Liu and Maciej Trela.
ATAPI transfers happen in two-to-three stages. The two stage atapi
commands are those that include a dma data transfer. The data transfer
portion of these operations is handled by the hardware packet-dma
acceleration. The three-stage commands do not have a data transfer and
are handled without hardware assistance in raw frame mode.
stage1: transmit host-to-device fis to notify the device of an incoming
atapi cdb. Upon reception of the pio-setup-fis repost the task_context
to perform the dma transfer of the cdb+data (go to stage3), or repost
the task_context to transmit the cdb as a raw frame (go to stage 2).
stage2: wait for hardware notification of the cdb transmission and then
go to stage 3.
stage3: wait for the arrival of the terminating device-to-host fis and
terminate the command.
To keep the implementation simple we only support ATAPI packet-dma
protocol (for commands with data) to avoid needing to handle the data
transfer manually (like we do for SATA-PIO). This may affect
compatibility for a small number of devices (see
ATA_HORKAGE_ATAPI_MOD16_DMA).
If the data-transfer underruns, or encounters an error the
device-to-host fis is expected to arrive in the unsolicited frame queue
to pass to libata for disposition. However, in the DONE_UNEXP_FIS (data
underrun) case it appears we need to craft a response. In the
DONE_REG_ERR case we do receive the UF and propagate it to libsas.
Signed-off-by: Maciej Trela <maciej.trela@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Libsas forget to set the sas_address and device type of rphy lead to file
under /sys/class/sas_x show wrong value, fix that.
Signed-off-by: Jack Wang <jack_wang@usish.com>
Tested-by: Crystal Yu <crystal_yu@usish.com>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
The queue-depth for libsas-attached devices initializes to 32 and can
only be increased manually via sysfs to a max of 64, while mpt2sas
attached devices initialize to 254 and dynamically float via the
midlayer ->change_queue_depth interface.
No performance regression was observed with this change on the isci
driver.
Tested-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Pass queue_depth change requests to libata, and prevent queue_type
changes for ATA devices.
Otherwise:
1/ we do not honor the libata specific restrictions on the queue depth
2/ libsas drivers that do not set sdev->tagged_supported are unable to
change the queue_depth of ata devices via sysfs
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Allow expander table-to-table attachments for
expanders that support it.
Signed-off-by: Luben Tuikov <ltuikov@yahoo.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Add SFF-8485 v0.7 / SAS-1 smp-write-gpio register support to libsas.
Defer SAS-2 support unless/until it defines an sgpio interface.
Minimum implementation needed to get the lights blinking.
try_test_sas_gpio_gp_bit() provides a common method to parse the
incoming write data (raw bitstream), and the to_sas_gpio_gp_bit() helper
routine can be used as a basis for the set/clear operations for the
'read' implementation. Host implementations parse as many bits
(ODx.[012]) as are locally supported and report the number of registers
successfully written. If the submitted data overruns the internal
number of registers available report the write as a success with the
number of bytes remaining reported in ->resid_len.
Example (assuming an active backplane) set the "identify" pattern for
the first 21 devices:
smp_write_gpio --count=2 --data=92,49,24,92,24,92,49,24 -t 4 --index=1 /dev/bsg/sas_hostX
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
expander child.
In an enclosure model where there are chaining expanders to a large body
of storage, it was discovered that libsas, responding to a broadcast
event change, would only revalidate the domain of first child expander
in the list.
The issue is that the pointer value to the discovered source device was
used to break out of the loop, rather than the content of the pointer.
This still remains non-compliant as the revalidate domain code is
supposed to loop through all child expanders, and not stop at the first
one it finds that reports a change count. However, the design of this
routine does not allow multiple device discoveries and that would be a
more complicated set of patches reserved for another day. We are fixing
the glaring bug rather than refactoring the code.
Signed-off-by: Mark Salyzyn <msalyzyn@us.xyratex.com>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
->queuecommand must return either 0, or one of the SCSI_MLQUEUE_* return
values. Non-transient errors are indicated by setting cmd->result before
calling ->scsi_done and returning 0. Fix libsas to adhere to this calling
convention. Note that the DID_ERROR for returns from the low-level driver
might not be correct for all cases, but it's the best we can do with
the current layering in libsas. I also suspect that the pre-existing
handling of -SAS_QUEUE_FULL should really be SCSI_MLQUEUE_HOST_BUSY, but
I'll leave that for a separate change.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Switch sas_queuecommand to a normal indentation and goto based error handling.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Now that isci has added a 3rd open coded user of this functionality just
share the libsas version.
Acked-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
If expander discovery fails (sas_discover_expander()), remove the
expander from the port device list (sas_ex_discover_expander()),
before freeing it. Else the list is corrupted and, e.g., when we
attempt to send SMP commands to other devices, the kernel oopses.
Signed-off-by: Luben Tuikov <ltuikov@yahoo.com>
Cc: stable@kernel.org
Reviewed-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
This allows a libsas driver to optionally provide a soft reset handler
for libata to drive. The isci driver allows software to control the
assertion/deassertion of SRST.
[jejb: checkpatch.pl fixes]
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
|
|
Head off doomed-to-fail i/o in sas_queuecommand before sending it down
the ata path.
Before:
sd 7:0:0:0: [sdd] Synchronizing SCSI cache
ata8: no sense translation for status: 0x00
ata8: translated ATA stat/err 0x00/00 to SCSI SK/ASC/ASCQ 0xb/00/00
ata8.00: device reported invalid CHS sector 0
ata8: status=0x00 { }
ata8: no sense translation for status: 0x00
ata8: translated ATA stat/err 0x00/00 to SCSI SK/ASC/ASCQ 0xb/00/00
ata8.00: device reported invalid CHS sector 0
ata8: status=0x00 { }
ata8: no sense translation for status: 0x00
ata8: translated ATA stat/err 0x00/00 to SCSI SK/ASC/ASCQ 0xb/00/00
ata8.00: device reported invalid CHS sector 0
ata8: status=0x00 { }
sd 7:0:0:0: [sdd] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
sd 7:0:0:0: [sdd] Sense Key : Aborted Command [current] [descriptor]
sd 7:0:0:0: [sdd] Add. Sense: No additional sense information
sd 7:0:0:0: [sdd] Stopping disk
After:
sd 9:0:0:0: [sdd] Synchronizing SCSI cache
sd 9:0:0:0: [sdd] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
sd 9:0:0:0: [sdd] Stopping disk
sd 9:0:0:0: [sdd] START_STOP FAILED
sd 9:0:0:0: [sdd] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
This is a cosmetic change as sata i/o can still leak to a gone device,
but this addresses the nominal hotplug case when releasing the target.
Acked-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
|
|
Commit 56dd2c06 "libsas: Don't issue commands to devices that have been
hot-removed" edited Darrick's original patch to remove setting 'gone' in
the sas_deform_port() path because that prevented scsi sync cache
commands from being issued when the driver was unloaded. However, this
allows true device gone notifications (as signaled port phy events) to
trigger sync cache commands to devices that are known to be unreachable.
Teach libsas which sas_deform_port() invocations are likely device gone
events.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
|
