| Age | Commit message (Collapse) | Author |
|---|
|
This patch does the following
- In case of errors if there least one data character in the RX FIFO
read it otherwise it may stall the receiver.
This is recommended in the interrupt reset method in the table 23-246 of
the omap4 TRM.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The legacy serial driver will detect the Winbond CIR device as a serial
port, since it looks exactly like a serial port unless you know what
it is from the PNP ID.
Here we track this port as a special PORT_8250_CIR type, preventing the
legacy serial driver from probing it.
Signed-off-by: Sean Young <sean@mess.org>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We first probe the legacy serial ports and then check pnp. If there
is a non-standard configuration then this might not work, also this
change is needed so we can blacklist Winbond CIR based on PNP ID.
For this to work the 8250_pnp driver must be merged into the 8250
module.
Signed-off-by: Sean Young <sean@mess.org>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Drop the check for "up" being valid on suspend/resume callbacks.
It should be valid always. Get rid of the "pdata" check also as
serial_omap_get_context_loss_count() checks for it.
Tested on omap4 panda and 3630 based Beagle board.
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
platform_get_drvdata always retrun a valid value after probe succeed.
It also fixed smatch warnings:
drivers/tty/serial/imx.c:1376 serial_imx_suspend() warn: variable dereferenced before check 'sport' (see line 1372)
drivers/tty/serial/imx.c:1392 serial_imx_resume() warn: variable dereferenced before check 'sport' (see line 1388)
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The autoconfig prints messages while holding the
port's spinlock and that causes a deadlock when
using serial console.
Signed-off-by: Flavio Leitner <fbl@redhat.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If a serial driver is called post hangup with a second DCD event then we
will attempt to get the ldisc of NULL. Check we have a tty before trying to
do anything with it.
This is still only safe within the uart layer if the caller holds the
relevant uart locks. We could do with a version where the tty is passed for
more general use.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Alan says these are not production ready, and users should be told this,
so put the "(EXPERIMENTAL)" marking back in the Kconfig entry string.
Reported-by: Alan Cox <alan@linux.intel.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
As discussed at the kernel summit this year, CONFIG_EXPERIMENTAL means
nothing, so let's get rid of it.
Cc: Kees Cook <keescook@chromium.org>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Return the value returned by the failing function instead
of -1 (which does not convey the right error information).
Fixes the following smatch warning:
drivers/tty/serial/samsung.c:1687 s3c24xx_serial_modinit() info:
why not propagate 'ret' from uart_register_driver() instead of -1?
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We don't want to free a random address if the entry is wrong, cover
this and WARN if it ever happens.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This pulls in the fixes in 3.6-rc6
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The mxs_auart_probe() gets the device by the get_device().
So we should put the device in the error path to balance the
device's reference counter.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
These workarounds do not apply for CONFIG_ARCH_OMAP2PLUS at all,
so let's make it just CONFIG_ARCH_OMAP1.
This is needed to for ARM common zImage changes for
omap2+ to avoid including plat and mach headers.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The driver explicitly requests a clock rate for the UART, but it is
off by a factor of four from the dividers that it programs into the
UART. Fix this by setting the rate to 1/4 of the current value.
Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The bug flag .interrupt_may_hang is not used since commit
4fd0690bb0c3955983560bb2767ee82e2b197f9b
"serial: pl011: implement workaround for CTS clear event issue"
so delete it.
Cc: Rajanikanth H.V <rajanikanth.hv@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The dereference should be moved below the NULL test.
spatch with a semantic match is used to found this.
(http://coccinelle.lip6.fr/)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Request pins using pinctrl framework. Only show a warning
on error as some boards set the pins in the bootloader
even if CONFIG_PINCTRL is enabled.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
OMAP Architecture code, passes a few function
pointers for UART driver to use in order to
properly implement Power Management and Wakeup
capabilities.
The problem is that those function pointers,
which are passed (ab)using platform_data on
non-DT kernels, can't be passed down to drivers
through DT.
commit e5b57c0 (serial: omap: define helpers
for pdata function pointers) failed to take DT
kernels into consideration and caused a regression
to DT kernel boot.
Fix that by (re-)adding a check for valid pdata
pointer together with valid pdata->$FUNCTION
pointer.
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
when rebasing patches on top of Greg's tty-next,
it looks like automerge broke a few things which
I didn't catch (for whatever reason I didn't
have OMAP Serial enabled on .config) so I ended
up breaking the build on Greg's tty-next branch.
Fix the breakage by re-adding the three missing
members on struct uart_omap_port.
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Added tty_device_create_release() and bound to dev->release in
tty_register_device_attr().
Added tty_port_register_device_attr() and used in uart_add_one_port()
instead of tty_register_device_attr().
Signed-off-by: Tomas Hlavacek <tmshlvck@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Added file /sys/devices/.../tty/ttySX/uartclk to allow reading
uartclk value in struct uart_port in serial_core via sysfs.
tty_register_device() has been generalized and refactored in order
to add support for setting drvdata and attribute_group to the device.
Signed-off-by: Tomas Hlavacek <tmshlvck@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fixes these build errors:
In file included from drivers/tty/serial/sccnxp.c:20:0:
include/linux/serial_core.h: In function 'uart_handle_break':
include/linux/serial_core.h:543:30: error: dereferencing pointer to incomplete type
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We call the get_device() in the mxs_auart_probe().
For the balance of the reference count, we should put the
device in the mxs_auart_remove().
Signed-off-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
After set the AUART_CTRL0_CLKGATE, the UART will gate all the clocks off.
So the following line will not take effect.
................................................................
writel(AUART_INTR_RXIEN | AUART_INTR_RTIEN | AUART_INTR_CTSMIEN,
u->membase + AUART_INTR_CLR);
................................................................
To fix this issue, the patch moves this gate-off line to
the end of setting registers.
Signed-off-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
sizeof when applied to a pointer typed expression gives the
size of the pointer.
Generated by: scripts/coccinelle/misc/noderef.cocci
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
enable RX FIFO for 16 characters and TX FIFO
for 16 spaces.
Tested-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
nobody needs to access the uart_omap_port structure
other than omap-serial.c file. Let's move that
structure definition to the C source file in order
to prevent anyone from accessing our structure.
Tested-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
this driver doesn't use any from <plat/dmtimer.h>, so
we can remove it without any problems.
This will, however cause a problem because omap-serial.c
was relying on indirect inclusion of <linux/platform_device.h>,
let's fix the issue by including <linux/platform_device.h>
on omap-serial.c as it should be.
Tested-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Software flow control register bits were not defined correctly.
Also clarify the IXON and IXOFF logic to reflect what userspace wants.
Cc: stable@vger.kernel.org
Tested-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
if we would reach serial_omap_get_char() while
Data Ready bit isn't set, we would return from
it without kicking our pm timer. This would mean
we would, eventually, have an unbalanced
pm_runtime_get on our device which would prevent
it from ever sleeping again.
Tested-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This has been missing from OMAP UART driver
for quite a while and it's simple enough
to implement it.
Tested-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch unlocks the port lock before calling a serial_core API
and re-acquires the port lock after calling it.
This patch fixes a system freeze issue seen when the serial_core
API uart_write_wakeup() eventually attempts to acquire the port lock
already acquired by omap serial interrupt handler.
Tested-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Ruchika Kharwar <ruchika@ti.com>
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Vijay Badawadagi <bvijay@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
it makes no sense to mark our IRQ handler inline
since it's passed as a function pointer when
enabling the IRQ line.
Tested-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Two functions:
omap_serial_fill_features_erratas() and
of_get_uart_port_info() are only called from probe().
Marking them as __devinit gives us another
oportunity to free some code after .init.text
is done.
Tested-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Ruchika Kharwar <ruchika@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
pm_runtime_enable() needs to be invoked before
pm_runtime_use_autosuspend(), and
pm_runtime_set_autosuspend_delay() functions.
Tested-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Ruchika Kharwar <ruchika@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When we're running our hardirq handler, there's
not need to disable IRQs with spin_lock_irqsave()
because IRQs are already disabled. It also makes
no difference if we save or not IRQ flags.
Switch over to simple spin_lock/spin_unlock and
drop the "flags" variable.
Tested-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
before removing the driver, let's make sure
to force device into a suspended state in order
to conserve power.
Tested-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
if platform_get_drvdata() returns NULL, that's
quite a nasty bug on the driver which we want to
catch ASAP. Otherwise, that check is hugely
unneeded.
Tested-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
by the time we call our first pm_runtme_get_sync()
after enable pm_runtime, our resume method might
be called. To avoid problems, we must make sure
that our dev->drvdata is set correctly before
our resume method gets called.
Tested-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Everytime we're done using our TTY, we want
the pm timer to be reinitilized. By sticking
to pm_runtime_pm_autosuspend() we make sure
that this will always be the case.
The idea behind this patch is to make sure we
will always reinitialize the pm timer so that
we don't fall into a situation where pm_runtime_put()
expires right away (if timer was already about to
expire when we made the call to pm_runtime_put()).
While suspending right away wouldn't cause any
issues, reinitializing the pm timer can help us
avoiding unnecessary context save & restore
operations (which are somewhat expensive) if there's
another read/write/set_termios request coming right
after. IOW, we are trying to make sure UART is still
powered up while it's still under heavy usage.
Tested-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
since all other IRQ types now do all necessary
checks inside their handlers, transmit_chars()
was the only one left expecting serial_omap_irq()
to check THRE for it. We can move THRE check to
transmit_chars() in order to make serial_omap_irq()
more uniform.
Tested-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
receive_chars() was getting too big and too difficult
to follow. By splitting it into separate RDI and RSLI
handlers, we have smaller functions which are easy
to understand and only touch the pieces which they need
to touch.
Tested-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
quite a few changes here, though they are
pretty obvious. In summary we're making sure
to detect which interrupt type we need to
handle before calling the underlying interrupt
handling procedure.
Tested-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The current support is known to be broken and
a later patch will come re-adding it using
dma engine API.
Tested-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The driver doesn't need to know about its platform_device.
Everything the driver needs can be done through the
struct device pointer. In case we need to use the
OMAP-specific PM function pointers, those can make
sure to find the device's platform_device pointer
so they can find the struct omap_device through
pdev->archdata field.
Tested-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
These were reported in bugzilla long ago with a hack patch. Now we have a
proper patch for one we can do the rest.
Resolves-bug: https://bugzilla.kernel.org/show_bug.cgi?id=25102
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In most of the time, the driver needs to check if the cts flow control
is enabled. But now, the driver checks the ASYNC_CTS_FLOW flag manually,
which is not a grace way. So add a new wraper function to make the code
tidy and clean.
Signed-off-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
this patch is in preparation to a few other changes
which will align on the prototype for function
pointers passed through pdata.
It also helps cleaning up the driver a little by
agregating checks for pdata in a single location.
Tested-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
