| Age | Commit message (Collapse) | Author |
|---|
|
Static analysis with cppcheck has shown a few instances of a variable
being reassigned a value before the old one has been used. None of these
ever require the old value to be used so remove the old values.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Static analysis with cppcheck has shown a few instances of a variable which
is assigned a value that is never used. A number of these are the return
status of various driver function calls which should be passed back to the
caller of the current function.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
...and cleanup some whitespace in other prototypes.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The e1000e driver has been converted to use extended descriptors instead of
the older legacy descriptor type.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Toggling the LANPHYPC Value bit cycles the power on the PHY and sets it
back to power-on defaults. This includes setting it's MAC-PHY messaging
mode to use the PCIe-like interconnect, so the MAC must also be set back
from SMBus mode to PCIe mode otherwise the PHY can be inaccessible.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The largest jumbo frame supported by the i217 and i218 hardware is 9018.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
As done with the previous generation managed 82579, prevent the PHY from
being put into an unknown state by blocking the hardware from automatically
configuring the PHY as done with the previous generation managed 82579.
Instead, the driver should configure the PHY with contents of the EEPROM
image.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
In rare instances, memory errors have been detected in the internal packet
buffer memory on I217/I218 when stressed under certain environmental
conditions. Enable Error Correcting Code (ECC) in hardware to catch both
correctable and uncorrectable errors. Correctable errors will be handled
by the hardware. Uncorrectable errors in the packet buffer will cause the
packet to be received with an error indication in the buffer descriptor
causing the packet to be discarded. If the uncorrectable error is in the
descriptor itself, the hardware will stop and interrupt the driver
indicating the error. The driver will then reset the hardware in order to
clear the error and restart.
Both types of errors will be accounted for in statistics counters.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Add PTP IEEE-1588 support and make accesible via the PHC subsystem.
v2: make e1000e_ptp_clock_info a static const struct per Stephen Hemminger
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Reviewed-by: Jacob Keller <Jacob.e.keller@intel.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The previous static flow-control thresholds were causing unnecessary pause
packets to be transmitted when jumbo frames are configured reducing the
throughput.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The SHRAH[9] register on I217 has a different R/W bit-mask than RAR and
SHRAL/H registers. Set R/W bit-mask appropriately for SHRAH[9] when
testing the R/W ability of the register. Also, fix the error message log
format so that it does not provide misleading information (i.e. the logged
register address could be incorrect).
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
John W. Linville says:
====================
This is a batch of fixes intende for the 3.8 stream.
Regarding the iwlwifi bits, Johannes says this:
"Please pull to get a single fix from Emmanuel for a bug I introduced due
to misunderstanding the code."
Regarding the mac80211 bits, Johannes says this:
"I have a few small fixes for you:
* some mesh frames would cause encryption warnings -- fixes from Bob
* scanning would pretty much break an association if we transmitted
anything to the AP while scanning -- fix from Stanislaw
* mode injection was broken by channel contexts -- fix from Felix
* FT roaming was broken: hardware crypto would get disabled by it"
Along with that, a handful of other fixes confined to specific drivers.
Avinash Patil fixes a typo in a NULL check in mwifiex.
Larry Finger fixes a build warning in rtlwifi. Seems safe...
Stanislaw Gruszka fixes iwlegacy to prevent microcode errors when
switching from IBSS mode to STA mode.
Felix Fietkau provides a trio of ath9k fixes related to proper tuning.
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Ben Greear reported crashes in ip_rcv_finish() on a stress
test involving many macvlans.
We tracked the bug to a dst use after free. ip_rcv_finish()
was calling dst->input() and got garbage for dst->input value.
It appears the bug is in loopback driver, lacking
a skb_dst_force() before calling netif_rx().
As a result, a non refcounted dst, normally protected by a
RCU read_lock section, was escaping this section and could
be freed before the packet being processed.
[<ffffffff813a3c4d>] loopback_xmit+0x64/0x83
[<ffffffff81477364>] dev_hard_start_xmit+0x26c/0x35e
[<ffffffff8147771a>] dev_queue_xmit+0x2c4/0x37c
[<ffffffff81477456>] ? dev_hard_start_xmit+0x35e/0x35e
[<ffffffff8148cfa6>] ? eth_header+0x28/0xb6
[<ffffffff81480f09>] neigh_resolve_output+0x176/0x1a7
[<ffffffff814ad835>] ip_finish_output2+0x297/0x30d
[<ffffffff814ad6d5>] ? ip_finish_output2+0x137/0x30d
[<ffffffff814ad90e>] ip_finish_output+0x63/0x68
[<ffffffff814ae412>] ip_output+0x61/0x67
[<ffffffff814ab904>] dst_output+0x17/0x1b
[<ffffffff814adb6d>] ip_local_out+0x1e/0x23
[<ffffffff814ae1c4>] ip_queue_xmit+0x315/0x353
[<ffffffff814adeaf>] ? ip_send_unicast_reply+0x2cc/0x2cc
[<ffffffff814c018f>] tcp_transmit_skb+0x7ca/0x80b
[<ffffffff814c3571>] tcp_connect+0x53c/0x587
[<ffffffff810c2f0c>] ? getnstimeofday+0x44/0x7d
[<ffffffff810c2f56>] ? ktime_get_real+0x11/0x3e
[<ffffffff814c6f9b>] tcp_v4_connect+0x3c2/0x431
[<ffffffff814d6913>] __inet_stream_connect+0x84/0x287
[<ffffffff814d6b38>] ? inet_stream_connect+0x22/0x49
[<ffffffff8108d695>] ? _local_bh_enable_ip+0x84/0x9f
[<ffffffff8108d6c8>] ? local_bh_enable+0xd/0x11
[<ffffffff8146763c>] ? lock_sock_nested+0x6e/0x79
[<ffffffff814d6b38>] ? inet_stream_connect+0x22/0x49
[<ffffffff814d6b49>] inet_stream_connect+0x33/0x49
[<ffffffff814632c6>] sys_connect+0x75/0x98
This bug was introduced in linux-2.6.35, in commit
7fee226ad2397b (net: add a noref bit on skb dst)
skb_dst_force() is enforced in dev_queue_xmit() for devices having a
qdisc.
Reported-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Tested-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-next
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a cpu notifier to virtio-net, so that we can reset the
virtqueue affinity if the cpu hotplug happens. It improve
the performance through enabling or disabling the virtqueue
affinity after doing cpu hotplug.
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Eric Dumazet <erdnetdev@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: virtualization@lists.linux-foundation.org
Cc: netdev@vger.kernel.org
Signed-off-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Split out the clean affinity function to virtnet_clean_affinity().
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Eric Dumazet <erdnetdev@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: virtualization@lists.linux-foundation.org
Cc: netdev@vger.kernel.org
Signed-off-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As Michael mentioned, set affinity and select queue will not work very
well when CPU IDs are not consecutive, this can happen with hot unplug.
Fix this bug by traversal the online CPUs, and create a per cpu variable
to find the mapping from CPU to the preferable virtual-queue.
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Eric Dumazet <erdnetdev@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: virtualization@lists.linux-foundation.org
Cc: netdev@vger.kernel.org
Signed-off-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Providing communication channel between KVM and e-Switch so that it
can be informed when hypervisor configures a MAC address and VLAN.
qlcnic_mac_learn module param usage will be changed to:
0 = MAC learning is disable
1 = Driver learning is enable
2 = FDB learning is enable
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
device eth0 entered promiscuous mode
BUG: sleeping function called from invalid context at mm/slub.c:930
in_atomic(): 1, irqs_disabled(): 0, pid: 5911, name: brctl
INFO: lockdep is turned off.
Pid: 5911, comm: brctl Tainted: GF W O 3.6.0-0.rc7.git1.4.fc18.x86_64 #1
Call Trace:
[<ffffffff810a29ca>] __might_sleep+0x18a/0x240
[<ffffffff811b5d77>] __kmalloc+0x67/0x2d0
[<ffffffffa00a61a9>] ? qlcnic_alloc_lb_filters_mem+0x59/0xa0 [qlcnic]
[<ffffffffa00a61a9>] qlcnic_alloc_lb_filters_mem+0x59/0xa0 [qlcnic]
[<ffffffffa009e1c1>] qlcnic_set_multi+0x81/0x100 [qlcnic]
[<ffffffff8159cccf>] __dev_set_rx_mode+0x5f/0xb0
[<ffffffff8159cd4f>] dev_set_rx_mode+0x2f/0x50
[<ffffffff8159d00c>] dev_set_promiscuity+0x3c/0x50
[<ffffffffa05ed728>] br_add_if+0x1e8/0x400 [bridge]
[<ffffffffa05ee2df>] add_del_if+0x5f/0x90 [bridge]
[<ffffffffa05eee0b>] br_dev_ioctl+0x4b/0x90 [bridge]
[<ffffffff8159d613>] dev_ifsioc+0x373/0x3b0
[<ffffffff8159d78f>] dev_ioctl+0x13f/0x860
[<ffffffff812dd6e1>] ? avc_has_perm_flags+0x31/0x2c0
[<ffffffff8157c18d>] sock_do_ioctl+0x5d/0x70
[<ffffffff8157c21d>] sock_ioctl+0x7d/0x2c0
[<ffffffff812df922>] ? inode_has_perm.isra.48.constprop.61+0x62/0xa0
[<ffffffff811e4979>] do_vfs_ioctl+0x99/0x5a0
[<ffffffff812df9f7>] ? file_has_perm+0x97/0xb0
[<ffffffff810d716d>] ? trace_hardirqs_on+0xd/0x10
[<ffffffff811e4f19>] sys_ioctl+0x99/0xa0
[<ffffffff816e7369>] system_call_fastpath+0x16/0x1b
br0: port 1(eth0) entered forwarding state
br0: port 1(eth0) entered forwarding state
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Provide port number in command payload for LED/Beaconing tests.
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
o Some adapter types do not support co-existence of Legacy Interrupt with
MSI-x or MSI among multiple functions. For those adapters, prevent attaching
to a function during normal load, if MSI-x or MSI vectors are not available.
o Using module parameters use_msi=0 and use_msi_x=0, driver can be loaded in
legacy mode for all functions in the adapter.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
o This patch enables RSS for TYPE-C packets to enable RSS for TCP over IPv6
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Sritej Velaga <sritej.velaga@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If rtsx_pci_sdmmc is not probed, function pointer pcr->slots[].card_event
will point to NULL, and thus rtsx_pci_card_detect will reference a NULL
pointer.
Check card_event pointer before referencing it can avoid kernel panic.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Updated in latest datasheet.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
If the twl4030_write_script function gets called with
a zero length argument, its return value does not
get set. We know that all scripts have a nonzero
length, but returning an error in case they ever
do is probably appropriate.
Without this patch, building omap2plus_defconfig results in:
drivers/mfd/twl4030-power.c: In function 'load_twl4030_script':
drivers/mfd/twl4030-power.c:414:5: error: 'err' may be used uninitialized in this function
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: "Kristo, Tero" <t-kristo@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
An issue has been reported where the PMIC either locks up or fails to
respond following a system Reset. This could result in a second write
in which the bus writes the current content of the write buffer to address
of the last I2C access.
The failure case is where this unwanted write transfers incorrect data to
a critical register.
This patch fixes this issue to by following any read or write with a dummy read
to a safe register address. A safe register address is one where the contents
will not affect the operation of the system.
Signed-off-by: Ashish Jangam <ashish.jangam@kpitcummins.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Add callback function conv_clk_and_div_n to convert between SSC clock
and its divider N.
For rtl8411, the formula to calculate SSC clock divider N is different
with the other card reader models.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Different card reader has different method to switch output voltage, so
we have to use the callback function provided by MFD driver to switch
output pad voltage.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Different card reader has different method to switch output voltage,
add this callback to let the card reader implement its individual switch
function.
This is needed as rtl8411 has a specific switch output voltage procedure.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Errors in CAN protocol (location) are reported in data[3] of the can
frame instead of data[2].
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Errors in CAN protocol (location) are reported in data[3] of the can
frame instead of data[2].
Cc: linux-stable <stable@vger.kernel.org>
Cc: Anant Gole <anantgole@ti.com>
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Errors in CAN protocol (location) are reported in data[3] of the can
frame instead of data[2].
Cc: linux-stable <stable@vger.kernel.org>
Cc: Bhupesh Sharma <bhupesh.sharma@st.com>
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The struct can_skb_priv is used to transport additional information along
with the stored struct can(fd)_frame that can not be contained in existing
struct sk_buff elements.
can_skb_priv is located in the skb headroom, which does not touch the existing
CAN sk_buff usage with skb->data and skb->len, so that even out-of-tree
CAN drivers can be used without changes.
Btw. out-of-tree CAN drivers without can_skb_priv in the sk_buff headroom
would not support features based on can_skb_priv.
The can_skb_priv->ifindex contains the first interface where the CAN frame
appeared on the local host. Unfortunately skb->skb_iif can not be used as this
value is overwritten in every netif_receive_skb() call.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Add support for canbus activity led indicators on usb_8dev devices by
calling appropriate can_led functions.
These are only enabled when CONFIG_CAN_LEDS is Y, becomes no-op
otherwise.
Signed-off-by: Bernd Krumboeck <krumboeck@universalnet.at>
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Add support for canbus activity led indicators on sja1000 devices by
calling appropriate can_led functions.
These are only enabled when CONFIG_CAN_LEDS is Y, becomes no-op
otherwise.
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Add support for canbus activity led indicators on mcp251x devices by
calling appropriate can_led functions.
These are only enabled when CONFIG_CAN_LEDS is Y, becomes no-op
otherwise.
Cc: Christian Pellegrin <chripell@fsfe.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Add support for canbus activity led indicators on c_can devices by
calling appropriate can_led functions.
These are only enabled when CONFIG_CAN_LEDS is Y, becomes no-op
otherwise.
Cc: Bhupesh Sharma <bhupesh.sharma@st.com>
Cc: AnilKumar Ch <anilkumar@ti.com>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Add support for canbus activity led indicators on ti_hecc devices by
calling appropriate can_led functions.
These are only enabled when CONFIG_CAN_LEDS is Y, becomes no-op
otherwise.
Cc: Anant Gole <anantgole@ti.com>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Add support for canbus activity led indicators on at91_can devices by
calling appropriate can_led functions.
These are only enabled when CONFIG_CAN_LEDS is Y, becomes no-op
otherwise.
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Add support for canbus activity led indicators on flexcan devices by
calling appropriate can_led_* functions.
These are only enabled when CONFIG_CAN_LEDS is Y, becomes no-op
otherwise.
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The LED trigger name for CAN devices is based on the initial
CAN device name, but does never change. The LED trigger name
is not guaranteed to be unique in case of hotplugging CAN devices.
This patch tries to address this problem by modifying the
LED trigger name according to the CAN device name when
the latter changes.
v1 - Kurt Van Dijck
v2 - Fabio Baltieri
- remove rename blocking if trigger is bound
- use led-subsystem function for the actual rename (still WiP)
- call init/exit functions from dev.c
v3 - Kurt Van Dijck
- safe operation for non-candev based devices (vcan, slcan)
based on earlier patch
v4 - Kurt Van Dijck
- trivial patch mistakes fixed
Signed-off-by: Kurt Van Dijck <kurt.van.dijck@eia.be>
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
In net_device notifier calls, it was impossible to determine
if a CAN device is based on candev in a safe way.
This patch adds such test in order to access candev storage
from within those notifiers.
Signed-off-by: Kurt Van Dijck <kurt.van.dijck@eia.be>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch implements the functions to add two LED triggers, named
<ifname>-tx and <ifname>-rx, to a canbus device driver.
Triggers are called from specific handlers by each CAN device driver and
can be disabled altogether with a Kconfig option.
The implementation keeps the LED on when the interface is UP and blinks
the LED on network activity at a configurable rate.
This only supports can-dev based drivers, as it uses some support field
in the can_priv structure.
Supported drivers should call devm_can_led_init() and can_led_event() as
needed.
Cleanup is handled automatically by devres, so no *_exit function is
needed.
Supported events are:
- CAN_LED_EVENT_OPEN: turn on tx/rx LEDs
- CAN_LED_EVENT_STOP: turn off tx/rx LEDs
- CAN_LED_EVENT_TX: trigger tx LED blink
- CAN_LED_EVENT_RX: trigger tx LED blink
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Add device driver for USB2CAN interface from "8 devices" (http://www.8devices.com).
changes since v10:
* small cleanups
changes since v9:
* fixed syslog messages
* fixed crc error number
* increased MAX_RX_URBS and MAX_TX_URBS
changes since v8:
* remove all sysfs files
changes since v7:
* add sysfs documentation
* fix minor styling issue
* fixed can state for passive mode
* changed handling for crc errors
changes since v6:
* changed some variable types to big endian equivalent
* small cleanups
changes since v5:
* unlock mutex on error
changes since v4:
* removed FSF address
* renamed struct usb_8dev
* removed unused variable free_slots
* replaced some _to_cpu functions with pointer equivalent
* fix return value for usb_8dev_set_mode
* handle can errors with separate function
* fix overrun error handling
* rewrite error handling for usb_8dev_start_xmit
* fix urb submit in usb_8dev_start
* various small fixes
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Bernd Krumboeck <krumboeck@universalnet.at>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
