| Age | Commit message (Collapse) | Author |
|---|
|
Allocate the required memory before calling usb_control_msg. And
the additional memory copy is necessary.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace 0 with the result from usbnet_cdc_bind().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Don't replace the usb_control_msg() with usbnet_{read,write}_cmd()
which couldn't be called inside suspend/resume callback. Keep the
basic functions unlimited. Instead, using usb_autopm_get_interface()
and usb_autopm_put_interface() in r815x_mdio_{read,write}().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some USB buffers use stack which may not be DMA-able.
Use the buffers from kmalloc to replace those one.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking fixes from David Miller:
1) Fix association failures not triggering a connect-failure event in
cfg80211, from Johannes Berg.
2) Eliminate a potential NULL deref with older iptables tools when
configuring xt_socket rules, from Eric Dumazet.
3) Missing RTNL locking in wireless regulatory code, from Johannes
Berg.
4) Fix OOPS caused by firmware loading races in ath9k_htc, from Alexey
Khoroshilov.
5) Fix usb URB leak in usb_8dev CAN driver, also from Alexey
Khoroshilov.
6) VXLAN namespace teardown fails to unregister devices, from Stephen
Hemminger.
7) Fix multicast settings getting dropped by firmware in qlcnic driver,
from Sucheta Chakraborty.
8) Add sysctl range enforcement for tcp_syn_retries, from Michal Tesar.
9) Fix a nasty bug in bridging where an active timer would get
reinitialized with a setup_timer() call. From Eric Dumazet.
10) Fix use after free in new mlx5 driver, from Dan Carpenter.
11) Fix freed pointer reference in ipv6 multicast routing on namespace
cleanup, from Hannes Frederic Sowa.
12) Some usbnet drivers report TSO and SG in their feature set, but the
usbnet layer doesn't really support them. From Eric Dumazet.
13) Fix crash on EEH errors in tg3 driver, from Gavin Shan.
14) Drop cb_lock when requesting modules in genetlink, from Stanislaw
Gruszka.
15) Kernel stack leaks in cbq scheduler and af_key pfkey messages, from
Dan Carpenter.
16) FEC driver erroneously signals NETDEV_TX_BUSY on transmit leading to
endless loops, from Uwe Kleine-König.
17) Fix hangs from loading mvneta driver, from Arnaud Patard.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (84 commits)
mlx5: fix error return code in mlx5_alloc_uuars()
mvneta: Try to fix mvneta when compiled as module
mvneta: Fix hang when loading the mvneta driver
atl1c: Fix misuse of netdev_alloc_skb in refilling rx ring
genetlink: fix usage of NLM_F_EXCL or NLM_F_REPLACE
af_key: more info leaks in pfkey messages
net/fec: Don't let ndo_start_xmit return NETDEV_TX_BUSY without link
net_sched: Fix stack info leak in cbq_dump_wrr().
igb: fix vlan filtering in promisc mode when not in VT mode
ixgbe: Fix Tx Hang issue with lldpad on 82598EB
genetlink: release cb_lock before requesting additional module
net: fec: workaround stop tx during errata ERR006358
qlcnic: Fix diagnostic interrupt test for 83xx adapters.
qlcnic: Fix setting Guest VLAN
qlcnic: Fix operation type and command type.
qlcnic: Fix initialization of work function.
Revert "atl1c: Fix misuse of netdev_alloc_skb in refilling rx ring"
atl1c: Fix misuse of netdev_alloc_skb in refilling rx ring
net/tg3: Fix warning from pci_disable_device()
net/tg3: Fix kernel crash
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull Xen fixes from Konrad Rzeszutek Wilk:
- Three fixes for ARM/ARM64 to either compile or not certain generic
drivers
- Fix for avoiding a potential deadlock when an user space event
channel is destroyed.
- Fix a workqueue resuming multiple times.
* tag 'stable/for-linus-3.11-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/tmem: do not allow XEN_TMEM on ARM64
xen/evtchn: avoid a deadlock when unbinding an event channel
xen/arm: enable PV control for ARM
xen/arm64: Don't compile cpu hotplug
xenbus: frontend resume cleanup
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some tiny USB fixes for 3.11-rc4
Nothing major, some gadget fixes, some new device ids, a new tiny
driver for the ANT+ USB device, and a number of fixes for the mos7840
driver that were much needed"
* tag 'usb-3.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: serial: ftdi_sio: add more RT Systems ftdi devices
usb: chipidea: fix the build error with randconfig
usb: chipidea: cast PORTSC_PTS and DEVLC_PTS macros
usb: gadget: udc-core: fix the typo of udc state attribute
usb: gadget: f_phonet: remove unused preprocessor conditional
usb: gadget: multi: fix error return code in cdc_do_config()
USB: mos7840: fix pointer casts
USB: mos7840: fix race in led handling
USB: mos7840: fix device-type detection
USB: mos7840: fix race in register handling
USB: serial: add driver for Suunto ANT+ USB device
usb: gadget: free opts struct on error recovery
usb: gadget: ether: put_usb_function on unbind
usb: musb: fix resource passed from glue layer to musb
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver fixes from Greg KH:
"Here are 4 tiny tty and serial driver fixes for 3.11-rc4.
Nothing big, a refcount leak, a module alias fix, and two fixes to the
mxs-auart serial driver"
* tag 'tty-3.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: arc_uart: Fix module alias
tty_port: Fix refcounting leak in tty_port_tty_hangup()
serial/mxs-auart: increase time to wait for transmitter to become idle
serial/mxs-auart: fix race condition in interrupt handler
|
|
Fix to return -ENOMEM from the ioremap error handling
case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the mvneta driver is compiled as module, the clock is disabled before
it's loading. This will reset the registers values and all configuration
made by the bootloader.
This patch sets the "sgmii serdes configuration" register to a magical value
found in:
https://github.com/yellowback/ubuntu-precise-armadaxp/blob/master/arch/arm/mach-armadaxp/armada_xp_family/ctrlEnv/mvCtrlEnvLib.c
With this change, the interrupts are working/generated and ethernet is
working.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the mvneta driver is compiled, it'll be loaded with clocks disabled.
This implies that the clocks should be enabled again before any register
access or it'll hang.
To fix it:
- enable clock earlier
- move timer callback after setting timer.data
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On Mon, 2013-07-29 at 08:30 -0700, Eric Dumazet wrote:
> On Mon, 2013-07-29 at 13:09 +0100, Luis Henriques wrote:
>
> >
> > I confirm that I can't reproduce the issue using this patch.
> >
>
> Thanks, I'll send a polished patch, as this one had an error if
> build_skb() returns NULL (in case sk_buff allocation fails)
Please try the following patch : It should use 2K frags instead of 4K
for normal 1500 mtu
Thanks !
[PATCH] atl1c: use custom skb allocator
We had reports ( https://bugzilla.kernel.org/show_bug.cgi?id=54021 )
that using high order pages for skb allocations is problematic for atl1c
We do not know exactly what the problem is, but we suspect that crossing
4K pages is not well supported by this hardware.
Use a custom allocator, using page allocator and 2K fragments for
optimal stack behavior. We might make this allocator generic
in future kernels.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Luis Henriques <luis.henriques@canonical.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Don't test for having link and let hardware deal with this situation.
Without this patch I see a machine running an -rt patched Linux being
stuck in sch_direct_xmit when it looses link while there is still a
packet to be sent. In this case the fec_enet_start_xmit routine returned
NETDEV_TX_BUSY which makes the network stack reschedule the packet and
so sch_direct_xmit calls fec_enet_start_xmit again.
I failed to reproduce a complete hang without -rt, but I think the
problem exists there, too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
tmem is not supported on arm or arm64 yet. Will revert this
once the Xen hypervisor supports it.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
Unbinding an event channel (either with the ioctl or when the evtchn
device is closed) may deadlock because disable_irq() is called with
port_user_lock held which is also locked by the interrupt handler.
Think of the IOCTL_EVTCHN_UNBIND is being serviced, the routine has
just taken the lock, and an interrupt happens. The evtchn_interrupt
is invoked, tries to take the lock and spins forever.
A quick glance at the code shows that the spinlock is a local IRQ
variant. Unfortunately that does not help as "disable_irq() waits for
the interrupt handler on all CPUs to stop running. If the irq occurs
on another VCPU, it tries to take port_user_lock and can't because
the unbind ioctl is holding it." (from David). Hence we cannot
depend on the said spinlock to protect us. We could make it a system
wide IRQ disable spinlock but there is a better way.
We can piggyback on the fact that the existence of the spinlock is
to make get_port_user() checks be up-to-date. And we can alter those
checks to not depend on the spin lock (as it's protected by u->bind_mutex
in the ioctl) and can remove the unnecessary locking (this is
IOCTL_EVTCHN_UNBIND) path.
In the interrupt handler we cannot use the mutex, but we do not
need it.
"The unbind disables the irq before making the port user stale, so when
you clear it you are guaranteed that the interrupt handler that might
use that port cannot be running." (from David).
Hence this patch removes the spinlock usage on the teardown path
and piggybacks on disable_irq happening before we muck with the
get_port_user() data. This ensures that the interrupt handler will
never run on stale data.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
[v1: Expanded the commit description a bit]
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394
Pull firewire regression fix from Stefan Richter:
"This fixes corrupted video capture, seen with IIDC/DCAM video and
certain buffer settings. (Regression since v3.4 inclusive.)"
* tag 'firewire-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394:
firewire: fix libdc1394/FlyCap2 iso event regression
|
|
RT Systems makes many usb serial cables based on the ftdi_sio driver for
programming various amateur radios. This patch is a full listing of
their current product offerings and should allow these cables to all
be recognized.
Signed-off-by: Rick Farina (Zero_Chaos) <zerochaos@gentoo.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Using below configs, the compile will have error:
ERROR: "ehci_init_driver" undefined!
.config:
CONFIG_USB_CHIPIDEA=m
CONFIG_USB_CHIPIDEA_HOST=y
CONFIG_USB_CHIPIDEA_DEBUG=y
The reason is chipidea host uses symbol from ehci, but ehci
is not compiled. Let the chipidea host depend on
ehci even it is built as module.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix the following build warnings on x86:
drivers/usb/chipidea/core.c: In function 'hw_phymode_configure':
drivers/usb/chipidea/core.c:226:3: warning: large integer implicitly truncated to unsigned type [-Woverflow]
drivers/usb/chipidea/core.c:230:3: warning: large integer implicitly truncated to unsigned type [-Woverflow]
drivers/usb/chipidea/core.c:243:3: warning: large integer implicitly truncated to unsigned type [-Woverflow]
drivers/usb/chipidea/core.c:246:3: warning: large integer implicitly truncated to unsigned type [-Woverflow]
Reported-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v3.11-rc3
Here are some fixes for v3.11-rc3. Mostly related to
the recent conversion to configfs done on the gadget
drivers, but we also have a fix for MUSB resources
on platforms which need 3 resources instead of 2, and
a fix for the sysfs_notify() call on udc-core.c which
was notifying an unexistent file.
|
|
Enable lifecyle management (reboot, shutdown...) from the toolstack
for ARM guests.
Signed-off-by: Julien Grall <julien.grall@linaro.org>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
|
|
On ARM64, when CONFIG_XEN=y, the compilation will fail because CPU hotplug is
not yet supported with XEN. For now, disable it.
Signed-off-by: Julien Grall <julien.grall@linaro.org>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
|
|
Only create the delayed resume workqueue if we are running in the same domain
as xenstored and issue a warning if the workqueue creation fails.
Move the work initialization to the device probe so it is done only once.
Signed-off-by: Aurelien Chartier <aurelien.chartier@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: David Vrabel <david.vrabel@citrix.com>
|
|
The name of udc state attribute file under sysfs is registered as
"state", while usb_gadget_set_state take it as "status" when it's
going to update. This patch fixes the typo.
Signed-off-by: Rong Wang <Rong.Wang@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Cc: <stable@kernel.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
The compatibility layer which the USBF_PHONET_INCLUDED was a part of
is no longer present - the USBF_PHONET_INCLUDED is not #defined by anyone
anymore, so the ifndef is always true. Removing it.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Fix to return a negative error code from the error handling
case instead of 0, as returned elsewhere in this function.
Introduced by commit 59835a (usb: gadget: multi: use
function framework for ACM.)
Make rndis_do_config() consistent with cdc_do_config() in the way it
handles returning the PTR_ERR(f_acm_*).
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
- Driver fixes for AM33xx, SIRF and PFC pin controllers
- Fix a compile warning from the pinctrl single-register driver
- Fix a little nasty memory leak
* tag 'pinctrl-for-v3.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: fix a memleak when freeing maps
pinctrl: pinctrl-single: fix compile warning when no CONFIG_PM
pinctrl: sh-pfc: fix SDHI0 VccQ regulator on sh73a0 with DT
arm/dts: sirf: fix the pingroup name mismatch between drivers and dts
pinctrl: sirf: add usp0_uart_nostreamctrl pin group for usp-uart without flowctrl
pinctrl: sirf: fix the pin number and mux bit for usp0
pinctrl: am33xx dt binding: correct include path
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is five bug fixes, two of which fix long standing problems
causing crashes (sd and mvsas). The remaining three are hung (isci
race) or lost (qla2xxx, isci) devices"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
[SCSI] isci: fix breakage caused by >16byte CDB patch
[SCSI] mvsas: Fix kernel panic on tile due to unaligned data access
[SCSI] sd: fix crash when UA received on DIF enabled device
[SCSI] qla2xxx: Properly set the tagging for commands.
[SCSI] isci: Fix a race condition in the SSP task management path
|
|
This patch fixes a VT mode check to make sure VLAN filters are disabled when
in promisc mode and VT is not enabled.
The problem with the previous check was that:
E1000_MRQC_ENABLE_VMDQ is defined as 0x00000003
but when not in VT mode:
mrqc |= E1000_MRQC_ENABLE_RSS_4Q (0x00000002)
So the above check will trigger regardless if VT mode is being used or not.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes an issue with the 82598EB device, where lldpad is causing Tx
Hangs on the card as soon as it attempts to configure DCB for the device. The
adapter will continually Tx hang and reset in a loop.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Cc: Stable <stable@vger.kernel.org>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Jack Morgan <jack.morgan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Silence compiler warnings on 64-bit systems introduced by commit
05cf0dec ("USB: mos7840: fix race in led handling") which uses the
usb-serial data pointer to temporarily store the device type during
probe but failed to add the required casts.
[gregkh - change uintptr_t to unsigned long]
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If the ready bit in the transmit buffer descriptor (TxBD[R])
is previously detected as not set during a prior frame transmission,
then the ENET_TDAR[TDAR] bit is cleared at a later time, even if
additional TxBDs were added to the ring and the ENET_TDAR[TDAR]
bit is set. This results in frames not being transmitted until
there is a 0-to-1 transition on ENET_TDAR[TDAR].
Workarounds:
code can use the transmit frame interrupt flag (ENET_EIR[TXF])
as a method to detect whether the ENET has completed transmission
and the ENET_TDAR[TDAR] has been cleared. If ENET_TDAR[TDAR] is
detected as cleared when packets are queued and waiting for transmit,
then a write to the TDAR bit will restart TxBD processing.
This case main happen when loading is light. A ethernet package may
not send out utile next package put into tx queue.
How to test:
while [ true ]
do
ping <IP> -s 10000 -w 4
ping <IP> -s 6000 -w 2
ping <IP> -s 4000 -w 2
ping <IP> -s 10000 -w 2
done
You will see below result in overnight test.
6008 bytes from 10.192.242.116: seq=1 ttl=128 time=0.722 ms
4008 bytes from 10.192.242.116: seq=0 ttl=128 time=1001.008 ms
4008 bytes from 10.192.242.116: seq=1 ttl=128 time=1.010 ms
10008 bytes from 10.192.242.116: seq=0 ttl=128 time=0.896 ms
After apply this patch, >1000ms delay disappear.
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
o Initialize proper interrupt handler for 83xx.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
o When configuring guest VLAN after PVID configuration, VF was loading
with previously configured PVID. Clear the PVID which was previously
configured before configuring guest VLAN.
o Display guest VLAN when it is configured
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Operation type and command type is not set correct in back channel
response.
Signed-off-by: Pratik Pujar <pratik.pujar@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Work function needs to be initialized before we participate in
inter device communication (IDC).
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit ebe7fdbaf3e90ea22feade6c9f5e50f42b23b6d8.
This change is not correct. GFP_DMA is not necessary for
this device.
There is some other problem causing this bug.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 18d627113b83 (firewire: prevent dropping of completed iso packet
header data) was intended to be an obvious bug fix, but libdc1394 and
FlyCap2 depend on the old behaviour by ignoring all returned information
and thus not noticing that not all packets have been received yet. The
result was that the video frame buffers would be saved before they
contained the correct data.
Reintroduce the old behaviour for old clients.
Tested-by: Stepan Salenikovich <stepan.salenikovich@gmail.com>
Tested-by: Josep Bosch <jep250@gmail.com>
Cc: <stable@vger.kernel.org> # 3.4+
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
Platform drivers use "platform:" prefix in module alias.
Also use DRIVER_NAME in MODULE_ALIAS to make module autoloading work.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The function tty_port_tty_hangup() could leak a reference to the tty_struct:
struct tty_struct *tty = tty_port_tty_get(port);
if (tty && (!check_clocal || !C_CLOCAL(tty))) {
tty_hangup(tty);
tty_kref_put(tty);
}
If tty != NULL and the second condition is false we never call tty_kref_put and
the reference is leaked.
Fix by always calling tty_kref_put() which accepts a NULL argument.
The patch fixes a regression introduced by commit aa27a094.
Acked-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Gianluca Anzolin <gianluca@sottospazio.it>
Acked-by: Jiri Slaby <jslaby@suse.cz>
Cc: stable <stable@vger.kernel.org> # 3.10
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Without this patch the driver waits ~1 ms for the UART to become idle. At
115200n8 this time is (theoretically) enough to transfer 11.5 characters
(= 115200 bits/s / (10 Bits/char) * 1ms). As the mxs-auart has a fifo size
of 16 characters the clock is gated too early. The problem is worse for
lower baud rates.
This only happens to really shut down the transmitter in the middle of a
transfer if /dev/ttyAPPx isn't opened in userspace (e.g. by a getty) but
was at least once (because the bootloader doesn't disable the transmitter).
So increase the timeout to 20 ms which should be enough for 9600n8, too.
Moreover skip gating the clock if the timeout is elapsed.
Cc: stable@vger.kernel.org # v2.6.39+
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The handler needs to ack the pending events before actually handling them.
Otherwise a new event might come in after it it considered non-pending or
handled and is acked then without being handled. So this event is only
noticed when the next interrupt happens.
Without this patch an i.MX28 based machine running an rt-patched kernel
regularly hangs during boot.
Cc: stable@vger.kernel.org # v2.6.39+
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
atl1c uses netdev_alloc_skb to refill its rx dma ring, but that call makes no
guarantees about the suitability of the memory for use in DMA. As a result
we've gotten reports of atl1c drivers occasionally hanging and needing to be
reset:
https://bugzilla.kernel.org/show_bug.cgi?id=54021
Fix this by modifying the call to use the internal version __netdev_alloc_skb,
where you can set the gfp_mask explicitly to include GFP_DMA.
Tested by two reporters in the above bug, who have the hardware to validate it.
Both report immediate cessation of the problem with this patch
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Jay Cliburn <jcliburn@gmail.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: stable@vger.kernel.org
Tested-by: Luis Henriques <luis.henriques@canonical.com>
Tested-by: Vincent Alquier <vincent.alquier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull drm fixes from Dave Airlie:
"This is just a regular fixes pull apart from the qxl one, it has
radeon and intel bits in it,
The intel fixes are for a regression with the RC6 fix and a 3.10 hdmi
regression, whereas radeon is more DPM fixes, a few lockup fixes and
some rn50/r100 DAC fixes"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon/dpm: fix r600_enable_sclk_control()
drm/radeon/dpm: implement force performance levels for rv6xx
drm/radeon/dpm: fix displaygap programming on rv6xx
drm/radeon/dpm: fix a typo in the rv6xx mclk setup
drm/i915: initialize gt_lock early with other spin locks
drm/i915: fix hdmi portclock limits
drm/radeon: fix combios tables on older cards
drm/radeon: improve dac adjust heuristics for legacy pdac
drm/radeon: Another card with wrong primary dac adj
drm/radeon: fix endian issues with DP handling (v3)
drm/radeon/vm: only align the pt base to 32k
drm/radeon: wait for 3D idle before using CP DMA
|
|
Pull qxl drm fixes from Dave Airlie:
"Okay as I warned, the qxl driver was running a bit free and loose with
its ttm object reservations and the new lockdep enabled reservation
tracking shone a bright light into it, it also with the new
reservations mutexes hits a possible deadlock during boot.
The first patch is a real fix to render the console correctly as the
driver used to just drop irq renderering as too hard, this also fixes
a sleeping while atomic warning.
The other two patches are the big ugly ones that redo how the driver
allocates objects and reserves them and makes things all work
properly, I've tested this in a VM, and compared to the current code
which hits a lockdep warning and the sleep while atomic warning before
failing.
So sorry this is coming in late, I should have tested qxl before
merging the mutex code, but I'd rather just fix qxl with this than
revert the reservations code at this point"
* 'qxl-fixes' of git://people.freedesktop.org/~airlied/linux:
qxl: convert qxl driver to proper use for reservations
qxl: allow creation of pre-pinned objects and use for releases.
drm/qxl: add delayed fb operations
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael Wysocki:
"These are just two fixes, a revert of the would-be backlight fix that
didn't work and an intel_pstate fix for two problems related to
maximum P-state selection.
Specifics:
- Revert of the ACPI video commit that I hoped would help fix
backlight problems related to Windows 8 compatibility on some
systems. Unfortunately, it turned out to cause problems to happen
too.
- Fix for two problems in intel_pstate, a possible failure to respond
to a load change on a quiet system and a possible failure to select
the highest available P-state on some systems. From Dirk
Brandewie"
* tag 'pm+acpi-3.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
Revert "ACPI / video / i915: No ACPI backlight if firmware expects Windows 8"
cpufreq / intel_pstate: Change to scale off of max P-state
|
|
The patch fixes following warning. The PCI device might have been
disabled somewhere else when we have EEH errors during early stage.
Device tg3 disabling already-disabled device
WARNING: at drivers/pci/pci.c:1403
:
NIP [c00000000044fd5c] .pci_disable_device+0xcc/0xe0
LR [c00000000044fd58] .pci_disable_device+0xc8/0xe0
Call Trace:
[c000003f80bc7370] [c00000000044fd58] .pci_disable_device+0xc8/0xe0
[c000003f80bc73f0] [d00000001cfe8fc0] .tg3_init_one+0x2f0/0x19f0 [tg3]
[c000003f80bc74d0] [c0000000004534e8] .local_pci_probe+0x68/0xb0
[c000003f80bc7560] [c0000000004537c8] .pci_device_probe+0x198/0x1a0
[c000003f80bc7610] [c0000000004f9e98] .driver_probe_device+0xd8/0x450
[c000003f80bc76a0] [c0000000004fa3bc] .__driver_attach+0x10c/0x110
[c000003f80bc7730] [c0000000004f6e94] .bus_for_each_dev+0x94/0x100
[c000003f80bc77d0] [c0000000004f9634] .driver_attach+0x34/0x50
[c000003f80bc7850] [c0000000004f8f98] .bus_add_driver+0x288/0x380
[c000003f80bc78f0] [c0000000004fae2c] .driver_register+0x9c/0x200
[c000003f80bc7980] [c000000000453214] .__pci_register_driver+0x64/0x90
[c000003f80bc7a10] [d00000001cff7a60] .tg3_driver_init+0x2c/0x40 [tg3]
[c000003f80bc7a80] [c00000000000b424] .do_one_initcall+0x144/0x1f0
[c000003f80bc7b70] [c0000000001244a0] .load_module+0x1f30/0x2700
[c000003f80bc7d40] [c000000000124e80] .SyS_finit_module+0xc0/0x110
[c000003f80bc7e30] [c000000000009dd4] syscall_exit+0x0/0x98
Reported-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Acked-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While EEH error happens, we might not have network device instance
(struct net_device) yet. So we can't access the instance safely and
check its link state, which causes kernel crash. The patch fixes it.
EEH: Frozen PE#2 on PHB#3 detected
EEH: This PCI device has failed 1 times in the last hour
EEH: Notify device drivers to shutdown
(NULL net_device): PCI I/O error detected
Unable to handle kernel paging request for data at address 0x00000048
Faulting instruction address: 0xd00000001c9387a8
Oops: Kernel access of bad area, sig: 11 [#1]
SMP NR_CPUS=1024 NUMA PowerNV
:
NIP [d00000001c9387a8] .tg3_io_error_detected+0x78/0x2a0 [tg3]
LR [d00000001c9387a4] .tg3_io_error_detected+0x74/0x2a0 [tg3]
Call Trace:
[c000003f93a0f960] [d00000001c9387a4] .tg3_io_error_detected+0x74/0x2a0 [tg3]
[c000003f93a0fa30] [c00000000003844c] .eeh_report_error+0xac/0x120
[c000003f93a0fac0] [c0000000000371bc] .eeh_pe_dev_traverse+0x8c/0x150
[c000003f93a0fb60] [c000000000038858] .eeh_handle_normal_event+0x128/0x3d0
[c000003f93a0fbf0] [c000000000038db8] .eeh_handle_event+0x2b8/0x2c0
[c000003f93a0fc90] [c000000000038e80] .eeh_event_handler+0xc0/0x170
[c000003f93a0fd30] [c0000000000cc000] .kthread+0xf0/0x100
[c000003f93a0fe30] [c00000000000a0dc] .ret_from_kernel_thread+0x5c/0x80
Reported-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Acked-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix race in LED handling introduced by commit 0eafe4de ("USB: serial:
mos7840: add support for MCS7810 devices") which reused the port control
urb for manipulating the LED without making sure that the urb is not
already in use. This could lead to the control urb being manipulated
while in flight.
Fix by adding a dedicated LED urb and ctrlrequest along with a LED-busy
flag to handle concurrency.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix race in device-type detection introduced by commit 0eafe4de ("USB:
serial: mos7840: add support for MCS7810 devices") which used a static
variable to hold the device type.
Move type detection to probe and use serial data to store the device
type.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
