Age | Commit message (Collapse) | Author |
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap fixes from Mark Brown:
"Two things here, one is a fix for a nasty issue where we were failing
to sync the last register in a block when using raw writes and the
other fixes a missing header for the !REGMAP stubs so that we don't
rely on implicit includes in that case"
* tag 'regmap-v3.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: Add missing header for !CONFIG_REGMAP stubs
regmap: cache: Make sure to sync the last register in a block
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fix from Mark Brown:
"Just one update for SPI, a simple fix to the davinci driver to correct
the direction for which DMA is mapped following the dmaengine
conversion"
* tag 'spi-v3.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: spi-davinci: Fix direction in dma_map_single()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull virtio fixes from Rusty Russell:
"More virtio console fixes than I'm happy with, but all real issues,
and all CC:stable.."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
virtio-scsi: Fix virtqueue affinity setup
virtio: console: return -ENODEV on all read operations after unplug
virtio: console: fix raising SIGIO after port unplug
virtio: console: clean up port data immediately at time of unplug
virtio: console: fix race in port_fops_open() and port unplug
virtio: console: fix race with port unplug and open/close
virtio/console: Add pipe_lock/unlock for splice_write
virtio/console: Quit from splice_write if pipe->nrbufs is 0
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Kevin Hilman:
- MSM: GPIO fixes (includes old code removal)
- OMAP: earlyprintk regression, AM33xx cpgmac PM regression
- OMAP5: urgent fix for potentially harmful voltage regulator values
- Renesas: gpio-keys fix, fix SD card detection, fix shdma calculation
error
- STi: critical SMP boot fix
- tegra: DTS fix for usb-phy
- a couple MAINTAINERS updates
(Arnd is on paternity leave, Kevin is stepping up to help arm-soc
maintenance)
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
MAINTAINERS: add TI Keystone ARM platform
MAINTAINERS: delete Srinidhi from ux500
ARM: tegra: enable ULPI phy on Colibri T20
ARM: STi: remove sti_secondary_start from INIT section.
ARM: STi: Fix cpu nodes with correct device_type.
ARM: shmobile: lager: do not annotate gpio_buttons as __initdata
ARM: shmobile: BOCK-W: fix SDHI0 PFC settings
shdma: fixup sh_dmae_get_partial() calculation error
ARM: OMAP2+: hwmod: AM335x: fix cpgmac address space
ARM: OMAP2+: hwmod: rt address space index for DT
ARM: OMAP2+: Sync hwmod state with the pm_runtime and omap_device state
ARM: OMAP2+: Avoid idling memory controllers with no drivers
ARM: OMAP2+: hwmod: Fix a crash in _setup_reset() with DEBUG_LL
ARM: dts: omap5-uevm: update optional/unused regulator configurations
ARM: dts: omap5-uevm: fix regulator configurations mandatory for SoC
ARM: dts: omap5-uevm: document regulator signals used on the actual board
ARM: msm: Consolidate gpiomux for older architectures
ARM: shmobile: armadillo800eva: Don't request GPIO 166 in board code
ARM: msm: dts: Fix the gpio register address for msm8960
|
|
It takes an unsigned value. This happens not to blow up on 64-bit
architectures, but it does on 32-bit, causing
drm_calc_vbltimestamp_from_scanoutpos() to calculate totally bogus
timestamps for vblank events. Which in turn causes e.g. gnome-shell to
hang after a DPMS off cycle with current xf86-video-ati Git.
[airlied: regression introduced in drm: use monotonic time in drm_calc_vbltimestamp_from_scanoutpos]
Cc: stable@vger.kernel.org
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=59339
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=59836
Tested-by: shui yangwei <yangweix.shui@intel.com>
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Some more radeon fixes. Mostly dpm and uvd fixes. Fixes hangs
with dpm on more rv6xx asics, and fixes suspend and resume with UVD.
* 'drm-fixes-3.11' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: make missing smc ucode non-fatal
drm/radeon/dpm: require rlc for dpm
drm/radeon/cik: use a mutex to properly lock srbm instanced registers
drm/radeon: remove unnecessary unpin
drm/radeon: add more UVD CS checking
drm/radeon: stop sending invalid UVD destroy msg
drm/radeon: only save UVD bo when we have open handles
drm/radeon: always program the MC on startup
drm/radeon: fix audio dto calculation on DCE3+ (v3)
drm/radeon/dpm: disable sclk ss on rv6xx
drm/radeon: fix halting UVD
drm/radeon/dpm: adjust power state properly for UVD on SI
drm/radeon/dpm: fix spread spectrum setup (v2)
drm/radeon/dpm: adjust thermal protection requirements
drm/radeon: select audio dto based on encoder id for DCE3
drm/radeon: properly handle pm on gpu reset
|
|
The smc ucode is required for dpm (dynamic power
management), but if it's missing just skip dpm setup
and don't disable acceleration.
Should fix:
https://bugs.freedesktop.org/show_bug.cgi?id=67876
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The rlc is required for dpm to work properly, so if
the rlc ucode is missing, don't enable dpm. Enabling
dpm without the rlc enabled can result in hangs.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
We need proper locking in the driver when accessing instanced
registers on CIK.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
We don't pin the BO on allocation, so don't unpin it on free.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Improve error handling in case userspace sends us
an invalid command buffer.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
We also need to check the handle.
Signed-off-by: Christian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Otherwise just reinitialize from scratch on resume,
and so make it more likely to succeed.
Signed-off-by: Christian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
For r6xx+ asics. This mirrors the behavior of pre-r6xx
asics. We need to program the MC even if something
else in startup() fails. Failure to do so results in
an unusable GPU.
Based on a fix from: Mark Kettenis <kettenis@openbsd.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
Need to set the wallclock ratio and adjust the phase
and module registers appropriately. May fix problems
with audio timing at certain display timings.
v2: properly handle clocks below 24mhz
v3: rebase r600 changes
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Enabling spread spectrum on the engine clock
leads to hangs on some asics.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=66963
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Removing the clock/power or resetting the VCPU can cause
hangs if that happens in the middle of a register write.
Stall the memory and register bus before putting the VCPU
into reset. Keep it in reset when unloading the module or
suspending.
Signed-off-by: Christian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
There are some hardware issue with reclocking on SI when
UVD is active, so use a stable power state when UVD is
active. Fixes possible hangs and performance issues when
using UVD on SI.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Need to check for engine and memory clock ss separately
and only enable dynamic ss if either of them are found.
This should fix systems which have a ss table, but do
not have entries for engine or memory. On those systems
we may enable dynamic spread spectrum without enabling
it on the engine or memory clocks which can lead to a
hang in some cases.
fixes some systems reported here:
https://bugs.freedesktop.org/show_bug.cgi?id=66963
v2: fix typo
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
On rv770 and newer, clock gating is not required
for thermal protection. The only requirement is that
the design utilizes a thermal sensor.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
There are two audio dtos on radeon asics that you can
select between. Normally, dto0 is used for hdmi and
dto1 for DP, but it seems that the dto is somehow
tied to the encoders on DCE3 asics.
fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=67435
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
When we reset the GPU, we need to properly tear
down power management before reseting the GPU and then
set it back up again after reset. Add the missing
radeon_pm_[suspend|resume] calls to the gpu reset
function.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
* pm-fixes:
cpufreq: rename ignore_nice as ignore_nice_load
cpufreq: loongson2: fix regression related to clock management
|
|
In theory, under a given ACPI namespace node there should be only
one child device object with _ADR whose value matches a given bus
address exactly. In practice, however, there are systems in which
multiple child device objects under a given parent have _ADR matching
exactly the same address. In those cases we use _STA to determine
which of the multiple matching devices is enabled, since some systems
are known to indicate which ACPI device object to associate with the
given physical (usually PCI) device this way.
Unfortunately, as it turns out, there are systems in which many
device objects under the same parent have _ADR matching exactly the
same bus address and none of them has _STA, in which case they all
should be regarded as enabled according to the spec. Still, if
those device objects are supposed to represent bridges (e.g. this
is the case for device objects corresponding to PCIe ports), we can
try harder and skip the ones that have no child device objects in the
ACPI namespace. With luck, we can avoid using device objects that we
are not expected to use this way.
Although this only works for bridges whose children also have ACPI
namespace representation, it is sufficient to address graphics
adapter detection issues on some systems, so rework the code finding
a matching device ACPI handle for a given bus address to implement
this idea.
Introduce a new function, acpi_find_child(), taking three arguments:
the ACPI handle of the device's parent, a bus address suitable for
the device's bus type and a bool indicating if the device is a
bridge and make it work as outlined above. Reimplement the function
currently used for this purpose, acpi_get_child(), as a call to
acpi_find_child() with the last argument set to 'false' and make
the PCI subsystem use acpi_find_child() with the bridge information
passed as the last argument to it. [Lan Tianyu notices that it is
not sufficient to use pci_is_bridge() for that, because the device's
subordinate pointer hasn't been set yet at this point, so use
hdr_type instead.]
This change fixes a regression introduced inadvertently by commit
33f767d (ACPI: Rework acpi_get_child() to be more efficient) which
overlooked the fact that for acpi_walk_namespace() "post-order" means
"after all children have been visited" rather than "on the way back",
so for device objects without children and for namespace walks of
depth 1, as in the acpi_get_child() case, the "post-order" callbacks
ordering is actually the same as the ordering of "pre-order" ones.
Since that commit changed the namespace walk in acpi_get_child() to
terminate after finding the first matching object instead of going
through all of them and returning the last one, it effectively
changed the result returned by that function in some rare cases and
that led to problems (the switch from a "pre-order" to a "post-order"
callback was supposed to prevent that from happening, but it was
ineffective).
As it turns out, the systems where the change made by commit
33f767d actually matters are those where there are multiple ACPI
device objects representing the same PCIe port (which effectively
is a bridge). Moreover, only one of them, and the one we are
expected to use, has child device objects in the ACPI namespace,
so the regression can be addressed as described above.
References: https://bugzilla.kernel.org/show_bug.cgi?id=60561
Reported-by: Peter Wu <lekensteyn@gmail.com>
Tested-by: Vladimir Lalov <mail@vlalov.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: 3.9+ <stable@vger.kernel.org> # 3.9+
|
|
This sysfs file was called ignore_nice_load earlier and commit
4d5dcc4 (cpufreq: governor: Implement per policy instances of
governors) changed its name to ignore_nice by mistake.
Lets get it renamed back to its original name.
Reported-by: Martin von Gagern <Martin.vGagern@gmx.net>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: 3.10+ <stable@vger.kernel.org> # 3.10+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Commit 42913c799 (MIPS: Loongson2: Use clk API instead of direct
dereferences) broke the cpufreq functionality on Loongson2 boards:
clk_set_rate() is called before the CPU frequency table is
initialized, and therefore will always fail.
Fix by moving the clk_set_rate() after the table initialization.
Tested on Lemote FuLoong mini-PC.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: 3.9+ <stable@vger.kernel.org> # 3.9+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
try_offline_node() checks that all CPUs associated with the given
node have been removed by using cpu_present_bits. If all cpus
related to that node have been removed, try_offline_node() clears
the node information.
However, try_offline_node() called from acpi_processor_remove() never
clears the node information. For disabling cpu_present_bits,
acpi_unmap_lsapic() needs be called. Yet, acpi_unmap_lsapic() is
called after try_offline_node() has run. So when try_offline_node()
runs, the CPU's cpu_present_bits is always set.
Fix the issue by moving try_offline_node() after acpi_unmap_lsapic().
The problem fixed here was uncovered by commit cecdb19 "ACPI / scan:
Change the implementation of acpi_bus_trim()".
[rjw: Changelog]
Signed-off-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Acked-by: Toshi Kani <toshi.kani@hp.com>
Cc: 3.9+ <stable@vger.kernel.org> # 3.9+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
On muxed systems, the other vgaswitcheroo client may depend on i915 to
handle the backlight. We began switching off the backlight since
commit a261b246ebd552fd5d5a8ed84cc931bb821c427f
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Thu Jul 26 19:21:47 2012 +0200
drm/i915: disable all crtcs at suspend time
breaking backlight on discreet graphics in (some) muxed systems.
Keep the backlight on when the state is changed through vgaswitcheroo.
Note: The alternative would be to add a quirk table to achieve the same
based on system identifiers, but AFAICS it would asymptotically approach
effectively the same as this patch as more IDs are added, but with the
maintenance burden of the quirk table.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=55311
Tested-by: Fede <fedevx@yahoo.com>
Tested-by: Aximab <laurent.debian@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=59785
Tested-by: sfievet <sebastien.fievet@free.fr>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
The SDVO code tries to compare the encoder's and crtc's idea of the
pixel_multiplier. Normally they have to match, but when transitioning
to DPMS off, we turn off the pipe before reading out the pipe_config,
so the pixel_multiplier in the pipe_config will be 0, whereas the
encoder will still have its pixel_multiplier set to whatever value we
were using when the display was active. This leads to a warning
from intel_modeset_check_state().
WARNING: CPU: 1 PID: 2846 at drivers/gpu/drm/i915/intel_sdvo.c:1378 intel_sdvo_get_config+0x158/0x160()
SDVO pixel multiplier mismatch, port: 0, encoder: 1
Modules linked in: snd_hda_codec_idt snd_hda_intel snd_hda_codec snd_hwdep
CPU: 1 PID: 2846 Comm: Xorg Not tainted 3.11.0-rc3-00208-gbe1e8d7-dirty #19
Hardware name: Apple Computer, Inc. Macmini1,1/Mac-F4208EC8, BIOS MM11.88Z.0055.B03.0604071521 04/07/06
00000000 00000000 ef0afa54 c1597bbb c1737ea4 ef0afa84 c10392ca c1737e6c
ef0afab0 00000b1e c1737ea4 00000562 c12dfbe8 c12dfbe8 ef0afb14 00000000
f697ec00 ef0afa9c c103936e 00000009 ef0afa94 c1737e6c ef0afab0 ef0afadc
Call Trace:
[<c1597bbb>] dump_stack+0x41/0x56
[<c10392ca>] warn_slowpath_common+0x7a/0xa0
[<c103936e>] warn_slowpath_fmt+0x2e/0x30
[<c12dfbe8>] intel_sdvo_get_config+0x158/0x160
[<c12c3220>] check_crtc_state+0x1e0/0xb10
[<c12cdc7d>] intel_modeset_check_state+0x29d/0x7c0
[<c12dfe5c>] intel_sdvo_dpms+0x5c/0xa0
[<c12985de>] drm_mode_obj_set_property_ioctl+0x40e/0x420
[<c1298625>] drm_mode_connector_property_set_ioctl+0x35/0x40
[<c1289294>] drm_ioctl+0x3e4/0x540
[<c10fc1a2>] do_vfs_ioctl+0x72/0x570
[<c10fc72f>] SyS_ioctl+0x8f/0xa0
[<c159b7fa>] sysenter_do_call+0x12/0x22
---[ end trace 7ce940aff1366d60 ]---
Fix the problem by skipping the encoder get_config() function for
inactive encoders.
Tested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Some card's max brightness level is pretty large, e.g. on Acer Aspire
4732Z, the max level is 989910. If user space set a large enough level
then the current scale done in intel_panel_set_backlight will cause an
integer overflow and the scaled level will be mistakenly small, leaving
user with an almost black screen. This patch fixes this problem.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
[danvet: Add a comment to explain what's going on.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
The DRM layer keeps track of our vblanks and it assumes our vblank
counters only go back to zero when they overflow. The problem is that
when we disable the power well our counters also go to zero, but it
doesn't mean they did overflow. So on this patch we grab the lock and
update last_vblank so the DRM layer won't think our counters
overflowed.
This patch fixes the following intel-gpu-tools test:
./kms_flip --run-subtest blocking-absolute-wf_vblank
Regression introduced by the following commit:
commit bf51d5e2cda5d36d98e4b46ac7fca9461e512c41
Author: Paulo Zanoni <paulo.r.zanoni@intel.com>
Date: Wed Jul 3 17:12:13 2013 -0300
drm/i915: switch disable_power_well default value to 1
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=66808
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: Added a comment that this might be better done in
drm_vblank_post_modeset in general.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Apparently Bspec is wrong in this case here even for gm45. Note that
Bspec is horribly misguided on i965g/gm, so we don't have any other
data points besides that it seems to make machines work better.
With this changes all the bits in PORT_HOTPLUG_STAT for the digital
ports are ordered the same way. This seems to agree with what register
dumps from the hpd storm handling code shows, where the LIVE bit and
the short/long pulse STATUS bits light up at the same time with this
enumeration (but no with the one from Bspec).
Also tested on my gm45 which has two DP+ ports, and everything seems
to still work as expected.
References: http://www.mail-archive.com/intel-gfx@lists.freedesktop.org/msg23054.html
Cc: Egbert Eich <eich@suse.com>
Cc: Jan Niggemann <jn@hz6.de>
Tested-by: Jan Niggemann <jn@hz6.de>
[danvet: Add a big warning that Bspec seems to be wrong for these
bits, suggested by Jani.]
Acked-by: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
same fix as cirrus and mgag200.
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
When a BO gets pinned the placement may get changed. If the memory is
mapped into user space and user space has already accessed the mapped
range the page tables are set up but now point to the wrong memory.
Set bo.mdev->dev_mapping in mgag200_bo_create() to make sure that
ttm_bo_unmap_virtual() called from ttm_bo_handle_move_mem() will take
care of this.
v2: Don't call ttm_bo_unmap_virtual() in mgag200_bo_pin(), fix comment.
Signed-off-by: Egbert Eich <eich@suse.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
This is a cirrus version of Egbert Eich's patch for mgag200.
Without bo.bdev->dev_mapping set, the ttm_bo_unmap_virtual_locked
called from ttm_bo_handle_move_mem returns with no effect. If any
application accessed the memory before it was moved, it will
access wrong memory next time. This causes crashes when changing
resolution down.
Signed-off-by: Michal Srb <msrb@suse.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata
Pull libata fix from Tejun Heo:
"Just the addition of MODULE_DEVICE_TABLE() for a platform driver"
* 'for-3.11-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
pata_imx: expose module alias for loading from device-tree
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Martin Schwidefsky:
"Enable LZ4 compression for the kernel image, add the machine id for
the new zBC12 model, fix an issue with hanging dasd devices, correct a
Kconfig dependency, fix a compile error in the perf module with
CONFIG_KVM=n and fix the find_next_bit_left primitive for the PCI base
layer"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/dasd: fix hanging devices after path events
s390/perf: fix compile error (undefined reference sie_exit)
s390/bitops: fix find_next_bit_left
s390: add support for IBM zBC12 machine
s390/Kconfig: select 'TTY' when 'S390_GUEST' is enabled
s390: add support for LZ4-compressed kernel
|
|
The physical_node_id_bitmap in struct acpi_device is only used for
looking up the first currently unused dependent phyiscal node ID
by acpi_bind_one(). It is not really necessary, however, because
acpi_bind_one() walks the entire physical_node_list of the given
device object for sanity checking anyway and if that list is always
sorted by node_id, it is straightforward to find the first gap
between the currently used node IDs and use that number as the ID
of the new list node.
This also removes the artificial limit of the maximum number of
dependent physical devices per ACPI device object, which now depends
only on the capacity of unsigend int. As a result, it fixes a
regression introduced by commit e2ff394 (ACPI / memhotplug: Bind
removable memory blocks to ACPI device nodes) that caused
acpi_memory_enable_device() to fail when the number of 128 MB blocks
within one removable memory module was greater than 32.
Reported-and-tested-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Toshi Kani <toshi.kani@hp.com>
Reviewed-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
|
|
The list of physical devices corresponding to an ACPI device
object is walked by acpi_system_wakeup_device_seq_show() and
physical_device_enable_wakeup() without taking that object's
physical_node_lock mutex. Since each of those functions may be
run at any time as a result of a user space action, the lack of
appropriate locking in them may lead to a kernel crash if that
happens during device hot-add or hot-remove involving the device
object in question.
Fix the issue by modifying acpi_system_wakeup_device_seq_show() and
physical_device_enable_wakeup() to use physical_node_lock as
appropriate.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: All <stable@vger.kernel.org>
|
|
regcache_sync_block_raw_flush() expects the address of the register after last
register that needs to be synced as its parameter. But the last call to
regcache_sync_block_raw_flush() in regcache_sync_block_raw() passes the address
of the last register in the block. This effectively always skips over the last
register in a block, even if it needs to be synced. In order to fix it increase
the address by one register.
The issue was introduced in commit 75a5f89 ("regmap: cache: Write consecutive
registers in a single block write").
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Add some necessary braces that have been removed during driver cleanup.
This fixes the I2C prescaler calculation.
Signed-off-by: Michael Brunner <michael.brunner@kontron.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Recently we have been seing some reports about PIO mode not working properly.
- http://www.spinics.net/lists/linux-i2c/msg11985.html
- http://marc.info/?l=linux-i2c&m=137235593101385&w=2
- https://lkml.org/lkml/2013/6/24/430
Let's use DMA mode even for small transfers.
Without this patch, i2c reads the incorrect sgtl5000 version on a mx28evk when
touchscreen is enabled:
[ 5.856270] sgtl5000 0-000a: Device with ID register 0 is not a sgtl5000
[ 9.877307] sgtl5000 0-000a: ASoC: failed to probe CODEC -19
[ 9.883528] mxs-sgtl5000 sound.12: ASoC: failed to instantiate card -19
[ 9.892955] mxs-sgtl5000 sound.12: snd_soc_register_card failed (-19)
Cc: <stable@vger.kernel.org>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Marek Vasut <marex@denx.de>
[wsa: we have a proper solution for -next, so this non intrusive
solution is OK for now]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Free sc->sc_page when releasing a struct o2net_sock_container
object to avoid memory leaks.
This issue has been fixed by Younger Liu for OCFS2, so I sync
that patch to zcache as we share the same network code base.
Cc: Younger Liu <younger.liu@huawei.com>
Cc: Bob Liu <bob.liu@oracle.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Jie Liu <jeff.liu@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit 98a5e9e99d05e9b6a14778b85631b55e8e349990.
IIO, like the rest of the kernel, should rely on dynamic debugging, not
have a special config option for it. That way, no user has to rebuild
their kernel to have debug messages, which is a good thing, let's not
revert back to the bad old days of the 2000's.
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First round of new IIO drivers, features and cleanups for the 3.12 cycle.
There has been a lot of good work going into IIO recently, some of which
missed this pull request purely because I haven't caught up with all my
emails.
Core changes
1) Introduction of devm_iio_device_alloc/free and conversions of lots of
drivers (37 + patches so far mostly from Sachin)
2) A Kconfig option to enabled some debug logging subsystem wide.
New drivers
1) Nuvoton NAU7802 adc driver
2) Avago APDS9300 ambient light sensor driver.
Staging graduations
1) ADIS16260 gyroscope (after a lot fo cleaning up from Lars-Peter)
New driver features
1) ST-sensors gain control of which pin is used for dataready.
2) mcp4725 gains eeprom saving (a later fix deals with a wrong return type
bug in that patch)
3) A number of drivers have gained module alias' to aid autoloading.
Cleanups and minor bug fixes.
1) A number of typos in Kconfig comments
2) Drop remaining mentions of ring buffers (now just buffers)
3) Overrestrictive i2c function checking in the invensense mpu6050 driver
4) Some help text clarifications.
5) store_eeprom is now used in several drivers so move to generic abi docs.
6) Update dac power down options.
7) Add some error handlign to mxs-lradc on stmp_reset_block call.
8) Lars fixed the alphabetical order in various files and added comments
to try and prevent them getting messed up again.
9) Dropped some remaining 'reset' attributes for drivers. We have never
seen a reason why these should be available. Finally the macro
used to define many of these has gone.
10) lps331ap gets an easier to check temperature scale implementation.
11) Various cleanups for the hmc5843 from Peter with a view to getting
it ready for a staging graduation.
Quite a few other little typo fixes etc.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
Second round of IIO fixes for the 3.11 cycle.
1) Fix a long term race in the IIO trigger handling.
This only effects cases where a single trigger is in use
by multiple devices.
2) ti_am335x fix an issue with incorrect data due to reading before
the sequencer is finished.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sarah/xhci into usb-linus
Sarah writes:
xhci: Misc bug fixes for 3.11.
Hi Greg,
Here's two small fixes for 3.11. The first patch fixes a 5 second hang in
khubd after a USB device disconnect on some xHCI hosts. The second fixes a
build warning.
Sarah Sharp
|
|
If the _BCL package ordering is descending, the first level
(br->levels[2]) is likely to be 0, and if the number of levels
matches the number of steps, we might confuse a returned level to
mean the index.
For example:
current_level = max_level = 100
test_level = 0
returned level = 100
In this case 100 means the level, not the index, and _BCM failed.
Still, if the _BCL package ordering is descending, the index of
level 0 is also 100, so we assume _BQC is indexed, when it's not.
This causes all _BQC calls to return bogus values causing weird
behavior from the user's perspective. For example:
xbacklight -set 10; xbacklight -set 20;
would flash to 90% and then slowly down to the desired level (20).
The solution is simple; test anything other than the first level
(e.g. 1).
[rjw: Changelog]
Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes
From Simon Horman:
Second round of Renesas ARM based SoC fixes for v3.11
* Lager board: do not annotate gpio_buttons as __initdata
- This avoids accessing uninitialised memory if keys are pressed
after kernel initialisation completes.
- Bug introduced in gpio-keys were enabled in v3.11-rc1
* Bock-W board: fix SDHI0 PFC settings
- Allow detection of SD card
- Bug introduced in SDHI support was added in v3.11-rc1
* shdma: fixup sh_dmae_get_partial() calculation error
- Bug introduced in 2.6.34-rc1.
* armadillo800eva board: Don't request GPIO 166 in board code
- Allow use of touchscreen
- Bug introduced in v3.11-rc1
* tag 'renesas-fixes2-for-v3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: lager: do not annotate gpio_buttons as __initdata
ARM: shmobile: BOCK-W: fix SDHI0 PFC settings
shdma: fixup sh_dmae_get_partial() calculation error
ARM: shmobile: armadillo800eva: Don't request GPIO 166 in board code
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Pull dmaengine fixes from Vinod Koul:
"Two fixes for slave dmaengine. The first fixes cyclic dma transfers
for pl330 and the second one makes us return the correct error code on
probe"
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
dma: pl330: Fix cyclic transfers
pch_dma: fix error return code in pch_dma_probe()
|