| Age | Commit message (Collapse) | Author |
|---|
|
We don't need to to check for mtd->resume before calling mtd_resume().
mtd_resume() should take care of that.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
This patch renames all MTD functions by adding a "_" prefix:
mtd->erase -> mtd->_erase
mtd->read_oob -> mtd->_read_oob
...
The reason is that we are re-working the MTD API and from now on it is
an error to use MTD function pointers directly - we have a corresponding
API call for every pointer. By adding a leading "_" we achieve the following:
1. Make sure we convert every direct pointer users
2. A leading "_" suggests that this interface is internal and it becomes
less likely that people will use them directly
3. Make sure all the out-of-tree modules stop compiling and the owners
spot the big API change and amend them.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
This patch adds a driver for the M-Sys / Sandisk diskonchip G4 nand flash found
in various smartphones and PDAs, among them the Palm Treo680, HTC Prophet and
Wizard, Toshiba Portege G900, Asus P526, and O2 XDA Zinc. It was tested on the
Treo 680, but should work generically.
Since v3, this patch adds power management functions, a scan of the factory bad
block table during initialization, several fixes, and more extensive testing.
Also, the platform data header file, which only contained partitioning
information, was removed. Command-line partitioning can be used, at least until
an mtd parser is written for the saftl format with which these chips are
shipped.
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Reviewed-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
This patch converts the drivers in drivers/mtd/* to use the
module_spi_driver() macro which makes the code smaller and a bit simpler.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
As nand_default_block_markbad() is becoming more complex, it helps to
have code appear only in its relevant codepath(s). Here, the calculation
of `ofs' based on NAND_BBT_SCANLASTPAGE is only useful on paths where we
write bad block markers to OOB. We move the condition/calculation closer
to the `write' operation and update the comment to more correctly
describe the operation.
The variable `wr_ofs' is also used to help isolate our calculation of
the "write" offset from the usage of `ofs' to represent the eraseblock
offset. This will become useful when we reorder operations in the next
patch.
This patch should make no functional change.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
The mtdoops usage instructions found in Kconfig have been incorrect
since:
commit 2e386e4bac90554887e73d6f342e845185b33fc3
mtd: mtdoops: refactor as a kmsg_dumper
mtdoops no longer uses a console. Now, if you build it into your kernel,
you add something like the following to your command line to select
partition X as your logging partition:
mtdoops.mtddev=X
Anyway, it seems better to leave the documentation out of Kconfig.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
/*
* This is here for documentation purposes only - until these people
* submit their machine types. It will be gone January 2005.
*/
It's now seven years after that date, so let's remove this.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Commit c4a9f88daf ([MTD] [NOR] fix ctrl-alt-del can't reboot for
intel flash bug) interferes with this work-around, causing MTD to
issue this warning:
Flash device refused suspend due to active operation (state 0)
The commit makes our work-around in the map driver unnecessary, so
let's remove it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Driver must cleanup all held resources during remove. It wasn't
releasing requested memory region.
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
SPEAr platforms (spear3xx/spear6xx/spear13xx) provide SMI (Serial Memory
Interface) controller to access serial NOR flash. SMI provides a simple
interface for SPI/serial NOR flashes and has certain inbuilt commands
and features to support these flashes easily. It also makes it possible
to map an address range in order to directly access (read/write) the SNOR
over address bus. This patch intends to provide serial nor driver support
for spear platforms which are accessed through SMI.
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
It seems that we have developed a bad-block-marking "feature" out of
pure laziness:
"We write two bytes per location, so we dont have to mess with 16 bit
access."
It's relatively simple to write a 1 byte at a time on x8 devices and 2
bytes at a time on x16 devices, so let's do it.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
nand_block_bad() doesn't check the correct pages when
NAND_BBT_SCAN2NDPAGE is enabled. It should scan both the OOB region of
both the 1st and 2nd page of each block.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Many NAND flash systems (especially those with MLC NAND) cannot be
reliably written twice in a row. For instance, when marking a bad block,
the block may already have data written to it, and so we should attempt
to erase the block before writing a bad block marker to its OOB region.
We can ignore erase failures, since the block may be bad such that it
cannot be erased properly; we still attempt to write zeros to its spare
area.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Add missing iounmap in error handling code, in a case where the function
already preforms iounmap on some other execution path.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e;
statement S,S1;
int ret;
@@
e = \(ioremap\|ioremap_nocache\)(...)
... when != iounmap(e)
if (<+...e...+>) S
... when any
when != iounmap(e)
*if (...)
{ ... when != iounmap(e)
return ...; }
... when any
iounmap(e);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Fix the following build warning:
drivers/mtd/mtdcore.c: In function ‘mtd_release’:
drivers/mtd/mtdcore.c:110: warning: unused variable ‘mtd’
This happens when neither CONFIG_MTD_CHAR nor CONFIG_MTD_CHAR_MODULE are defined.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Because it is useless to call it if the device is opened in R/O mode, and also
harmful: on CFI NOR flash it may block for long time waiting for erase
operations to complete is another partition with a R/W file-system on this
chip.
Artem Bityutskiy: write commit message, amend the patch to match the latest
tree (we use mtd_sync(), not mtd->sync() nowadays).
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Since "length" is a u32, the error handling below didn't work when
fixup_pmc551() returns -ENODEV.
if ((length = fixup_pmc551(PCI_Device)) <= 0)
This patch changes both the type of "length" and the return type of
fixup_pmc551() to int.
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
This allows the mtdoops driver to work on flash chips using the
AMD/Fujitsu compatible command set.
As the code comments note, the locks used throughout the normal code
paths in the driver are ignored, so that the chance of writing out the
kernel's last messages are maximized.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6
SCSI fixes from James Bottomley:
"There's just a single fix in here: the osd max device number fix."
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] osd_uld: Bump MAX_OSD_DEVICES from 64 to 1,048,576
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/parisc-2.6
PARISC fixes from James Bottomley:
"This is a set of build fixes to get the cross compiled architecture
testbeds building again"
* tag 'parisc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/parisc-2.6:
[PARISC] don't unconditionally override CROSS_COMPILE for 64 bit.
[PARISC] include <linux/prefetch.h> in drivers/parisc/iommu-helpers.h
[PARISC] fix compile break caused by iomap: make IOPORT/PCI mapping functions conditional
|
|
Pull from Herbert Xu:
"This push fixes a bug in mv_cesa that causes all hash operations
that supply data on a final operation to fail."
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: mv_cesa - fix final callback not ignoring input data
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
hhwmon fixes for 3.3-rc6 from Guenter Roeck:
These patches are necessary for correct operation and management of
F75387.
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (f75375s) Catch some attempts to write to r/o registers
hwmon: (f75375s) Properly map the F75387 automatic modes to pwm_enable
hwmon: (f75375s) Make pwm*_mode writable for the F75387
hwmon: (f75375s) Fix writes to the pwm* attribute for the F75387
|
|
fbdev fixes for 3.3 from Florian Tobias Schandinat
It includes:
- two fixes for OMAP HDMI
- one fix to make new OMAP functions behave as they are supposed to
- one Kconfig dependency fix
- two fixes for viafb for modesetting on VX900 hardware
* tag 'fbdev-fixes-for-3.3-2' of git://github.com/schandinat/linux-2.6:
OMAPDSS: APPLY: make ovl_enable/disable synchronous
OMAPDSS: panel-dvi: Add Kconfig dependency on I2C
viafb: fix IGA1 modesetting on VX900
viafb: select HW scaling on VX900 for IGA2
OMAPDSS: HDMI: hot plug detect fix
OMAPDSS: HACK: Ensure DSS clock domain gets out of idle when HDMI is enabled
|
|
It makes no sense to attempt to manually configure the fan in auto mode,
or set the duty cycle directly in closed loop mode. The corresponding
registers are then read-only. If the user tries it nonetheless, error out
with EINVAL instead of silently doing nothing.
Signed-off-by: Nikolaus Schulz <mail@microschulz.de>
[guenter.roeck@ericsson.com: Minor formatting cleanup]
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
The F75387 supports automatic fan control using either PWM duty cycle or
RPM speed values. Make the driver detect the latter mode, and expose the
different modes in sysfs as per pwm_enable, so that the user can switch
between them.
The interpretation of the pwm_enable attribute for the F75387 is adjusted
to be a superset of those values used for similar Fintek chips which do
not support automatic duty mode, with 2 mapping to automatic speed mode,
and moving automatic duty mode to the new value 4.
Toggling the duty mode via pwm_enable is currently denied for the F75387,
as the chip then simply reinterprets the fan configuration register values
according to the new mode, switching between RPM and PWM units, which
makes this a dangerous operation.
This patch introduces a new pwm mode into the driver. This is necessary
because the new mode (automatic pwm mode, 4) may already be enabled by the
BIOS, and the driver should not break existing functionality. This was seen
on at least one board.
Signed-off-by: Nikolaus Schulz <mail@microschulz.de>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
Watchdog updates from Wim Van Sebroeck:
* git://www.linux-watchdog.org/linux-watchdog:
watchdog: fix GETTIMEOUT ioctl in booke_wdt
watchdog: update maintainers git entry
watchdog: Fix typo in pnx4008_wdt.c
watchdog: Fix typo in Kconfig
watchdog: fix error in probe() of s3c2410_wdt (reset at booting)
watchdog: hpwdt: clean up set_memory_x call for 32 bit
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull from Mark Brown:
"A simple, driver specific fix. This device isn't widely used outside
of Marvell reference boards most of which are probably used with their
BSPs rather than with mainline so low risk."
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: fix the ldo configure according to 88pm860x spec
|
|
git://git.pengutronix.de/git/wsa/linux-2.6
i2c bugfix from Wolfram Sang:
"This patch fixes a wrong assumption in the mxs-i2c-driver about a
command queue being done. Without it, we have seen races when the
bus was under load."
* 'i2c-embedded/for-3.3' of git://git.pengutronix.de/git/wsa/linux-2.6:
i2c: mxs: only flag completion when queue is completely done
|
|
DRM fixes from Dave Airlie:
intel: fixes for output regression on 965GM, an oops and a machine
hang
radeon: uninitialised var (that gcc didn't warn about for some reason)
+ a couple of correctness fixes.
exynos: fixes for various things, drop some chunks of unused code.
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon/kms/vm: fix possible bug in radeon_vm_bo_rmv()
drm/radeon: fix uninitialized variable
drm/radeon/kms: fix radeon_dp_get_modes for LVDS bridges (v2)
drm/i915: Remove use of the autoreported ringbuffer HEAD position
drm/i915: Prevent a machine hang by checking crtc->active before loading lut
drm/i915: fix operator precedence when enabling RC6p
drm/i915: fix a sprite watermark computation to avoid divide by zero if xpos<0
drm/i915: fix mode set on load pipe. (v2)
drm/exynos: exynos_drm.h header file fixes
drm/exynos: added panel physical size.
drm/exynos: added postclose to release resource.
drm/exynos: removed exynos_drm_fbdev_recreate function.
drm/exynos: fixed page flip issue.
drm/exynos: added possible_clones setup function.
drm/exynos: removed pageflip_event_list init code when closed.
drm/exynos: changed priority of mixer layers.
drm/exynos: Fix typo in exynos_mixer.c
|
|
Merge virtio pull request from Rusty Russell.
* tag 'for-linus' of git://github.com/rustyrussell/linux:
virtio: balloon: leak / fill balloon across S4
|
|
commit e562966dbaf49e7804097cd991e5d3a8934fc148 added support for S4 to
the balloon driver. The freeze function did nothing to free the pages,
since reclaiming the pages from the host to immediately give them back
(if S4 was successful) seemed wasteful. Also, if S4 wasn't successful,
the guest would have to re-fill the balloon. On restore, the pages were
supposed to be marked freed and the free page counters were incremented
to reflect the balloon was totally deflated.
However, this wasn't done right. The pages that were earlier taken away
from the guest during a balloon inflation operation were just shown as
used pages after a successful restore from S4. Just a fancy way of
leaking lots of memory.
Instead of trying that, just leak the balloon on freeze and fill it on
restore/thaw paths. This works properly now. The optimisation to not
leak can be added later on after a bit of refactoring of the code.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
|
|
ovl->enable/disable are meant to be synchronous so that they can handle
the configuration of fifo sizes. The current kernel doesn't configure
fifo sizes yet, and so the code doesn't need to block to function (from
omapdss driver's perspective).
However, for the users of omapdss a non-blocking ovl->disable is
confusing, because they don't know when the memory area is not used
any more.
Furthermore, when the fifo size configuration is added in the next merge
window, the change from non-blocking to blocking could cause side
effects to the users of omapdss. So by making the functions block
already will keep them behaving in the same manner.
And, while not the main purpose of this patch, this will also remove the
compile warning:
drivers/video/omap2/dss/apply.c:350: warning:
'wait_pending_extra_info_updates' defined but not used
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
|
|
panel-dvi uses i2c, but the Kconfig didn't have dependency on I2C. Add
it.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Arnd Bergmann says:
"Another set of arm-soc bug fixes on top of v3.3-rc5. The few larger
bits are all for devices that still need to get set up in board code.
Only three platforms are in this set of fixes: omap2+, pxa and lpc32xx."
* tag 'fixes-3.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (22 commits)
ARM: LPC32xx: serial.c: Fixed loop limit
ARM: LPC32xx: serial.c: HW bug workaround
ARM: LPC32xx: irq.c: Clear latched event
ARM: LPC32xx: Fix interrupt controller init
ARM: LPC32xx: Fix irq on GPI_28
ARM: OMAP2: fix mailbox init code
ARM: OMAP2+: gpmc-smsc911x: add required smsc911x regulators
ARM: OMAP1: Fix out-of-bounds array access for Innovator
OMAP3 EVM: remove out-of-bounds array access of gpio_leds
ARM: OMAP: Fix build error when mmc_omap is built as module
ARM: OMAP: Fix kernel panic with HSMMC when twl4030_gpio is a module
pxa/hx4700: add platform device and I2C info for AK4641 codec
arch/arm/mach-pxa/: included linux/gpio.h twice
arch/arm/mach-mmp/: some files include some headers twice
ARM: pxa: fix error handling in pxa2xx_drv_pcmcia_probe
ARM: pxa: fix including linux/gpio.h twice
ARM: pxa: fix mixed declarations and code in sharpsl_pm
ARM: pxa: fix wrong parsing gpio event on spitz
ARM: OMAP2+: usb-host: fix compile warning
ARM: OMAP4: Move the barrier memboclk_steal() as part of reserve callback
...
|
|
The bo is removed from the list at the top of
radeon_vm_bo_rmv(), but then the list is used
in radeon_vm_bo_update_pte() to look up the vm.
remove the bo_list entry at the end of the
function instead.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jerome Glisse <j.glisse@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Without this fix the driver randomly treats
textures as arrays and I'm really wondering
why gcc isn't complaining about it.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
git://git.infradead.org/users/kmpark/linux-2.6-samsung into HEAD
* 'exynos-drm-fixes' of git://git.infradead.org/users/kmpark/linux-2.6-samsung:
drm/exynos: exynos_drm.h header file fixes
drm/exynos: added panel physical size.
drm/exynos: added postclose to release resource.
drm/exynos: removed exynos_drm_fbdev_recreate function.
drm/exynos: fixed page flip issue.
drm/exynos: added possible_clones setup function.
drm/exynos: removed pageflip_event_list init code when closed.
drm/exynos: changed priority of mixer layers.
drm/exynos: Fix typo in exynos_mixer.c
|
|
Need to call ExternalEncoderControl to set up DDC before
trying to get an EDID for all DP bridge chips (including
DP to LVDS).
Also remove redundant encoder assignment.
V2: fix typo in commit message.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Commit dcfb748422 ([WATCHDOG] fix book E watchdog to take
WDIOC_SETTIMEOUT arg in seconds) fixed SETTIMEOUT ioctl
to use seconds as a parameter instead of some hardware-specific
"period", but missed to apply similar changes to GETTIMEOUT,
so it still returns "period" value. Let's fix it!
Also, while at it, make SETTIMEOUT ioctl return real timeout
value as it should do according to the documentation.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Signed-off-by: Nikolaus Schulz <mail@microschulz.de>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
For the F75387, the register holding the current PWM duty cycle value is
r/o; changing it requires writing to the fan expect register instead.
Signed-off-by: Nikolaus Schulz <mail@microschulz.de>
[guenter.roeck@ericsson.com: Simplified function parameters]
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
IOMMU fixes for Linux 3.3-rc5
All the fixes are for the OMAP IOMMU driver. The first patch is the
biggest one. It fixes the calls of the function omap_find_iovm_area() in
the omap-iommu-debug module which expects a 'struct device' parameter
since commit fabdbca instead of an omap_iommu handle. The
omap-iommu-debug code still passed the handle to the function which
caused a crash.
The second patch fixes a NULL pointer dereference in the OMAP code and
the third patch makes sure that the omap-iommu is initialized before the
omap-isp driver, which relies on the iommu. The last patch is only a
workaround until defered probing is implemented.
* tag 'iommu-fixes-v3.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
ARM: OMAP: make iommu subsys_initcall to fix builtin omap3isp
iommu/omap: fix NULL pointer dereference
iommu/omap: fix erroneous omap-iommu-debug API calls
|
|
Correct spelling "resouce" to "resource" in
drivers/watchdog/pnx4008_wdt.c
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Correct spelling "overidden" to "overridden" in
drivers/watchdog/Kconfig
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Probe function of s3c2410 watchdog calls request_irq before initializing
required value (wdt_count). This incurs resetting watchdog counter value
and watchdog-reboot during booting up.
This patch addresses such an issue by calling request_irq later.
Error handling in probe function and calling oder in remove function are
also revised accordingly.
Reported-by: Chanwoo Park <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
1. address has to be page aligned.
2. set_memory_x uses page size argument, not size.
Bug causes with following commit:
commit da28179b4e90dda56912ee825c7eaa62fc103797
Author: Mingarelli, Thomas <Thomas.Mingarelli@hp.com>
Date: Mon Nov 7 10:59:00 2011 +0100
watchdog: hpwdt: Changes to handle NX secure bit in 32bit path
commit e67d668e147c3b4fec638c9e0ace04319f5ceccd upstream.
This patch makes use of the set_memory_x() kernel API in order
to make necessary BIOS calls to source NMIs.
Signed-off-by: Maxim Uvarov <maxim.uvarov@oracle.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: stable <stable@vger.kernel.org>
|
|
Broken by commit 6ef84509f3d439ed2d43ea40080643efec37f54f for users
passing a request with non-zero 'nbytes' field, like e.g. testmgr.
Cc: <stable@kernel.org> # 3.0+
Signed-off-by: Phil Sutter <phil.sutter@viprinet.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/drm-intel into HEAD
* 'drm-intel-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/drm-intel:
drm/i915: Remove use of the autoreported ringbuffer HEAD position
drm/i915: Prevent a machine hang by checking crtc->active before loading lut
drm/i915: fix operator precedence when enabling RC6p
drm/i915: fix a sprite watermark computation to avoid divide by zero if xpos<0
drm/i915: fix mode set on load pipe. (v2)
|
|
* 'lpc32xx/fixes' of git://git.antcom.de/linux-2.6: (5 commits)
ARM: LPC32xx: serial.c: Fixed loop limit
ARM: LPC32xx: serial.c: HW bug workaround
ARM: LPC32xx: irq.c: Clear latched event
ARM: LPC32xx: Fix interrupt controller init
ARM: LPC32xx: Fix irq on GPI_28
Update to Linux 3.3-rc5
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
