| Age | Commit message (Collapse) | Author |
|---|
|
It's not needed anymore.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
mlx4 currently uses a too high tx coalescing setting, deferring
TX completion interrupts by up to 128 us.
With the recent skb_orphan() removal in commit 8112ec3b872,
performance of a single TCP flow is capped to ~4 Gbps, unless
we increase tcp_limit_output_bytes.
I suggest using 16 us instead of 128 us, allowing a finer control.
Performance of a single TCP flow is restored to previous levels,
while keeping TCP small queues fully enabled with default sysctl.
This patch is also a BQL prereq.
Reported-by: Vimalkumar <j.vimal@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Yevgeny Petrilin <yevgenyp@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Acked-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch gets the runtime PM reference count before calling
usbnet_{read|write}_cmd, and puts it after completion of the
usbnet_{read|write}_cmd, so that the usb control message can always
be sent to one active device in the non-PM context.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch applies the introduced usbnet_read_cmd_nopm() and
usbnet_write_cmd_nopm() in the callback of resume and suspend
to avoid deadlock if USB runtime PM is considered into
usbnet_read_cmd() and usbnet_write_cmd().
Cc: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes memory leak in smsc95xx_suspend.
Also, it isn't necessary to bother mm to allocate 8bytes/16byte,
and we can use stack variable safely.
Acked-By: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch applies the introduced usbnet_read_cmd_nopm() and
usbnet_write_cmd_nopm() in the callback of resume and suspend
to avoid deadlock if USB runtime PM is considered into
usbnet_read_cmd() and usbnet_write_cmd().
Cc: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch introduces the below two helpers to prepare for solving
the usbnet runtime PM problem, which may cause some network utilities
(ifconfig, ethtool,...) touch a suspended device.
usbnet_read_cmd_nopm()
usbnet_write_cmd_nopm()
The above two helpers should be called by usbnet resume/suspend
callback to avoid deadlock.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On gcc 4.7, we will get alignment traps in the ip stack if we don't align
the ip headers on receive. The h/w can support this, so use ip aligned
allocations.
Cut down the unnecessary padding on the allocation. The buffer can start on
any byte alignment, but the size including the begining offset must be 8
byte aligned. So the h/w buffer size must include the NET_IP_ALIGN offset.
Thanks to Eric Dumazet for the initial patch highlighting the padding issues.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Only generate tx interrupts on every ring size / 4 descriptors. Move the
netif_stop_queue call to the end of the xmit function rather than
checking at the beginning.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The interrupts have already been cleared, so we don't need to clear them
again. Also, we could miss interrupts if they are cleared, but we don't
process the packet.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The standard readl/writel accessors involve a spinlock and cache sync
operation on ARM platforms with an outer cache. Only DMA triggering
accesses need this, so use the raw variants instead in the critical paths.
The relaxed variants would be more appropriate, but don't exist on all
arches.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
New received frames will trigger the rx DMA to poll the DMA descriptors,
so there is no need to tell the h/w to poll. We also want to enable
dropping frames from the fifo when there is no buffer.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Enable the tx dma to start reading the next frame while sending the current
frame.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
instead of making separate tg3_napi_disable() and netif_tx_disable() calls.
Update version to 3.126.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for 5717C0 which is a 5720A0 with special bonds-out option.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If no pinctrl available just report a warning as some architecture may not
need to do anything.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Tested-by: Joachim Eastwood <manabian@gmail.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Tested-by: Joachim Eastwood <manabian@gmail.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixed some coding style issues.
Signed-off-by: Kumar Amit Mehta <gmate.amit@gmail.com>
Acked-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
checkpatch.pl throws error message for the current code. This patch fixes
this coding style issue.
Signed-off-by: Kumar Amit Mehta <gmate.amit@gmail.com>
Acked-by: Jitendra Kalsaria <Jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The following chips need to enable internal settings to let ASPM
and clock request work.
RTL8111E-VL, RTL8111F, RTL8411, RTL8111G
RTL8105, RTL8402, RTL8106
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use WARN rather than printk followed by WARN_ON(1), for conciseness.
A simplified version of the semantic patch that makes this transformation
is as follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression list es;
@@
-printk(
+WARN(1,
es);
-WARN_ON(1);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Building atp.o triggers this GCC warning:
drivers/net/ethernet/realtek/atp.c: In function ‘set_rx_mode’:
drivers/net/ethernet/realtek/atp.c:871:26: warning: ‘mc_filter[0]’ may be used uninitialized in this function [-Wuninitialized]
GCC is correct. In promiscuous mode 'mc_filter' will be used
uninitialized in set_rx_mode_8012(), which is apparently inlined into
set_rx_mode().
But it turns out set_rx_mode_8012() will never be called, since
net_local.chip_type will always be RTL8002. So we can just remove
set_rx_mode_8012() and do some related cleanups.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The CPSW driver remaps two different IO regions, but fails to unmap them
both. This patch fixes the issue by calling iounmap in the appropriate
places.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The code mixes up the CPSW_SS and the CPSW_WR register naming. This patch
changes the names to conform to the published Technical Reference Manual
from TI, in order to make working on the code less confusing.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When underlying phy driver restores its state very fast after being brought
down and up so that macb driver function macb_handle_link_change() was never
called with link state "down", driver's internal representation of phy speed
and duplex (bp->speed and bp->duplex) didn't change. So, macb driver sees no
reason to perform actual write to the NCFGR register, although the speed and
duplex settings in that register were reset when interface was brought down
and up. In that case actual phy speed and duplex differ from NCFGR settings.
The patch fixes that by keeping internal driver representation of speed and
duplex in sync with actual content of NCFGR.
Signed-off-by: Vitalii Demianets <vitas@nppfactor.kiev.ua>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Ben Hutchings recently came up with a better way to handle the kconfig
dependencies for the PTP hardware clocks. This patch converts one new and
one older driver to the new scheme.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
"ip link add ... type vxlan ... ttl X" allows a user to set the TTL
used by a VXLAN for encapsulation. The provided value was ignored by
vxlan module and the default value of 1 was used when encapsulating
multicast packets.
Signed-off-by: Vincent Bernat <bernat@luffy.cx>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support for wol wakeup on unicast, broadcast,
multicast and arp frames.
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After d58d46b5 (r8169: jumbo fixes.) max frame len is stored in
rtl_chip_infos[].jumbo_max for each chip and SafeMtu should be gone.
Signed-off-by: Kirill Smelkov <kirr@mns.spb.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Function name should include '_ether_addr'.
Return type should be bool.
Parameter name should be 'addr' not 'dest' (also matching kernel-doc).
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This was missed in commit a24006ed12616bde1bbdb26868495906a212d8dc
('ptp: Enable clock drivers along with associated net/PHY drivers')
which enabled sfc's clock driver unconditionally.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It seems that to avoid deadlocks it is enough to poll vq before
we are going to use the last buffer. This is faster than
c70aa540c7a9f67add11ad3161096fb95233aa2e.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Even when vhost-net is in zero-copy transmit mode,
net core might still decide to copy the skb later
which is somewhat slower than a copy in user
context: data copy overhead is added to the cost of
page pin/unpin. The result is that enabling tx zero copy
option leads to higher CPU utilization for guest to guest
and guest to host traffic.
To fix this, suppress zero copy tx after a given number of
packets triggered late data copy. Re-enable periodically
to detect workload changes.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Zerocopy handling code is vhost-net specific.
Move it from vhost.c/vhost.h out to net.c
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This will be used to disable zerocopy when error rate
is high.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Better document macros for DMA tracking. Add an
explicit one for DMA in progress instead of
relying on user supplying len != 1.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When tun transmits a zero copy skb, it orphans the frags
which might need to allocate extra memory, in atomic context.
If that fails, notify ubufs callback before freeing the skb
as a hint that device should disable zerocopy mode.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Even if skb is marked for zero copy, net core might still decide
to copy it later which is somewhat slower than a copy in user context:
besides copying the data we need to pin/unpin the pages.
Add a parameter reporting such cases through zero copy callback:
if this happens a lot, device can take this into account
and switch to copying in user context.
This patch updates all users but ignores the passed value for now:
it will be used by follow-up patches.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-next
Jeff Kirsher says:
====================
This series contains updates to igb, ixgbe and e1000.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This was picked up by sparse.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds a driver for the FEC(MX6) that offers time
stamping and a PTP haderware clock. Because FEC\ENET(MX6)
hardware frequency adjustment is complex, we have implemented
this in software by changing the multiplication factor of the
timecounter.
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A new file fec_ptp.c will use fec_enet_private to support 1588 PTP
move such structure to common header file fec.h
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch hooks into the CPTS code and adds support for the HWTSTAMP
ioctl. The patch includes code for the CPSW version found in the dm814x
even though the background device tree support for this board is still
missing.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds a way to configure the CPTS input clock scaling factors
via the device tree.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Because time stamping on both external ports of the switch simultaneously
is positively useless from the application's point of view, this patch
provides a DT configuration method to choose the active port.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds a driver for the CPTS that offers time
stamping and a PTP hardware clock. Because some of the
CPTS hardware variants (like the am335x) do not support
frequency adjustment, we have implemented this in software
by changing the multiplication factor of the timecounter.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
