Age | Commit message (Collapse) | Author |
|
Section 4.11.7.1 of rev 1.0 of the xhci specification states that a link TRB
can only occur at a boundary between underlying USB frames (512 bytes for
high speed devices).
If this isn't done the USB frames aren't formatted correctly and, for example,
the USB3 ethernet ax88179_178a card will stop sending (while still receiving)
when running a netperf tcp transmit test with (say) and 8k buffer.
This should be a candidate for stable, the ax88179_178a driver defaults to
gso and tso enabled so it passes a lot of fragmented skb to the USB stack.
Notes from Sarah:
Discussion: http://marc.info/?l=linux-usb&m=138384509604981&w=2
This patch fixes a long-standing xHCI driver bug that was revealed by a
change in 3.12 in the usb-net driver. Commit
638c5115a794981441246fa8fa5d95c1875af5ba "USBNET: support DMA SG" added
support to use bulk endpoint scatter-gather (urb->sg). Only the USB
ethernet drivers trigger this bug, because the mass storage driver sends
sg list entries in page-sized chunks.
This patch only fixes the issue for bulk endpoint scatter-gather. The
problem will still occur for periodic endpoints, because hosts will
interpret no-op transfers as a request to skip a service interval, which
is not what we want.
Luckily, the USB core isn't set up for scatter-gather on isochronous
endpoints, and no USB drivers use scatter-gather for interrupt
endpoints. Document this known limitation so that developers won't try
to use urb->sg for interrupt endpoints until this issue is fixed. The
more comprehensive fix would be to allow link TRBs in the middle of the
endpoint ring and revert this patch, but that fix would touch too much
code to be allowed in for stable.
This patch should be backported to kernels as old as 3.12, that contain
the commit 638c5115a794981441246fa8fa5d95c1875af5ba "USBNET: support DMA
SG". Without this patch, the USB network device gets wedged, and stops
sending packets. Mark Lord confirms this patch fixes the regression:
http://marc.info/?l=linux-netdev&m=138487107625966&w=2
Signed-off-by: David Laight <david.laight@aculab.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Mark Lord <mlord@pobox.com>
Cc: stable@vger.kernel.org
|
|
We need to make sure that the error code from devm_of_pwm_get() is the one
the module returns in case of failure.
Restructure the code to make this possible for DT booted case.
With this patch the driver can ask for deferred probing when the board is
booted with DT.
Fixes for example omap4-sdp board's keyboard backlight led.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
In commit 7314e613d5ff ("Fix a few incorrectly checked
[io_]remap_pfn_range() calls") the uio driver started more properly
checking the passed-in user mapping arguments against the size of the
actual uio driver data.
That in turn exposed that some driver authors apparently didn't realize
that mmap can only work on a page granularity, and had tried to use it
with smaller mappings, with the new size check catching that out.
So since it's not just the user mmap() arguments that can be confused,
make the uio mmap code also verify that the uio driver has the memory
allocated at page boundaries in order for mmap to work. If the device
memory isn't properly aligned, we return
[ENODEV]
The fildes argument refers to a file whose type is not supported by mmap().
as per the open group documentation on mmap.
Reported-by: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Greg KH <gregkh@linuxfoundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Bug report from: wenxiong@linux.vnet.ibm.com
The issue is happened in dual controller configuration. We got the
sysfs warnings when rmmod the ipr module.
enclosure_unregister() in drivers/msic/enclosure.c, call device_unregister()
for each componment deivce, device_unregister() ->device_del()->kobject_del()
->sysfs_remove_dir(). In sysfs_remove_dir(), set kobj->sd = NULL.
For each componment device,
enclosure_component_release()->enclosure_remove_links()->sysfs_remove_link()
in which checking kobj->sd again, it has been set as NULL when doing
device_unregister. So we saw all these sysfs WARNING.
Tested-by: wenxiong@linux.vnet.ibm.com
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
When multiple vectors are used, the vector variable is over written,
resulting in unhandled operation for those vectors.
This fix prevents the problem by maitaining HBA instance and
vector values for each irq.
[jejb: checkpatch fixes]
Signed-off-by: Nikith.Ganigarakoppal@pmcs.com
Signed-off-by: Anandkumar.Santhanam@pmcs.com
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Setting the phy state for hard reset response.
After sending hard reset for a device ,phy down event sets
the phy state to zero but for phy up event it will not set
the phy state again.This will cause problem to successive
hard resets.
Signed-off-by: Nikith.Ganigarakoppal@pmcs.com
Signed-off-by: Anandkumar.Santhanam@pmcs.com
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
In case of direct attached SATA device delay is not enough.
It will give crash for set device state command response and
wait_for_completion is the best solution for this.
Signed-off-by: Nikith.Ganigarakoppal@pmcs.com
Signed-off-by: Anandkumar.Santhanam@pmcs.com
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Signed-off-by: Nikith.Ganigarakoppal@pmcs.com
Signed-off-by: Anandkumar.Santhanam@pmcs.com
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Thomas Gleixner:
- Correction of fuzzy and fragile IRQ_RETVAL macro
- IRQ related resume fix affecting only XEN
- ARM/GIC fix for chained GIC controllers
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip: Gic: fix boot for chained gics
irq: Enable all irqs unconditionally in irq_resume
genirq: Correct fuzzy and fragile IRQ_RETVAL() definition
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull Xen bug-fixes from Konrad Rzeszutek Wilk:
"Fixes to patches that went in this merge window along with a latent
bug:
- Fix lazy flushing in case m2p override fails.
- Fix module compile issues with ARM/Xen
- Add missing call to DMA map page for Xen SWIOTLB for ARM"
* tag 'stable/for-linus-3.13-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/gnttab: leave lazy MMU mode in the case of a m2p override failure
xen/arm: p2m_init and p2m_lock should be static
arm/xen: Export phys_to_mach to fix Xen module link errors
swiotlb-xen: add missing xen_dma_map_page call
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A smattering of driver specific fixes here, including a bunch for a
long standing common pattern in the error handling paths, and a fix
for an embarrassing thinko in the new devm master registration code"
* tag 'spi-v3.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi/pxa2xx: Restore private register bits.
spi/qspi: Fix qspi remove path.
spi/qspi: cleanup pm_runtime error check.
spi/qspi: set correct platform drvdata in ti_qspi_probe()
spi/pxa2xx: add new ACPI IDs
spi: core: invert success test in devm_spi_register_master
spi: spi-mxs: fix reference leak to master in mxs_spi_remove()
spi: bcm63xx: fix reference leak to master in bcm63xx_spi_remove()
spi: txx9: fix reference leak to master in txx9spi_remove()
spi: mpc512x: fix reference leak to master in mpc512x_psc_spi_do_remove()
spi: rspi: use platform drvdata correctly in rspi_remove()
spi: bcm2835: fix reference leak to master in bcm2835_spi_remove()
|
|
Pull networking updates from David Miller:
"Here is a pile of bug fixes that accumulated while I was in Europe"
1) In fixing kernel leaks to userspace during copying of socket
addresses, we broke a case that used to work, namely the user
providing a buffer larger than the in-kernel generic socket address
structure. This broke Ruby amongst other things. Fix from Dan
Carpenter.
2) Fix regression added by byte queue limit support in 8139cp driver,
from Yang Yingliang.
3) The addition of MSG_SENDPAGE_NOTLAST buggered up a few sendpage
implementations, they should just treat it the same as MSG_MORE.
Fix from Richard Weinberger and Shawn Landden.
4) Handle icmpv4 errors received on ipv6 SIT tunnels correctly, from
Oussama Ghorbel. In particular we should send an ICMPv6 unreachable
in such situations.
5) Fix some regressions in the recent genetlink fixes, in particular
get the pmcraid driver to use the new safer interfaces correctly.
From Johannes Berg.
6) macvtap was converted to use a per-cpu set of statistics, but some
code was still bumping tx_dropped elsewhere. From Jason Wang.
7) Fix build failure of xen-netback due to missing include on some
architectures, from Andy Whitecroft.
8) macvtap double counts received packets in statistics, fix from Vlad
Yasevich.
9) Fix various cases of using *_STATS_BH() when *_STATS() is more
appropriate. From Eric Dumazet and Hannes Frederic Sowa.
10) Pktgen ipsec mode doesn't update the ipv4 header length and checksum
properly after encapsulation. Fix from Fan Du.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (61 commits)
net/mlx4_en: Remove selftest TX queues empty condition
{pktgen, xfrm} Update IPv4 header total len and checksum after tranformation
virtio_net: make all RX paths handle erors consistently
virtio_net: fix error handling for mergeable buffers
virtio_net: Fixed a trivial typo (fitler --> filter)
netem: fix gemodel loss generator
netem: fix loss 4 state model
netem: missing break in ge loss generator
net/hsr: Support iproute print_opt ('ip -details ...')
net/hsr: Very small fix of comment style.
MAINTAINERS: Added net/hsr/ maintainer
ipv6: fix possible seqlock deadlock in ip6_finish_output2
ixgbe: Make ixgbe_identify_qsfp_module_generic static
ixgbe: turn NETIF_F_HW_L2FW_DOFFLOAD off by default
ixgbe: ixgbe_fwd_ring_down needs to be static
e1000: fix possible reset_task running after adapter down
e1000: fix lockdep warning in e1000_reset_task
e1000: prevent oops when adapter is being closed and reset simultaneously
igb: Fixed Wake On LAN support
inet: fix possible seqlock deadlocks
...
|
|
This patch resolves a dead lock issue that could be incurred when
exynos_drm_crtc_dpms function was called.
The exynos_drm_crtc_dpms function waits for the completion of pended
page flip events. However, preclose callback - this releases all unhandled
page flip events - is called prior to the exynos_drm_crtc_dpms function call
when drm is closed. So at this time, this will make the exynos_drm_crtc_dpms
to wait infiniately for the completion of the page flip events.
This patch releases the unhandled page flip events at postclose instead
of preclose so that exynos_drm_crtc_dpms function can be waked up.
Changelog v2:
- fix a memory leak when drm is closed.
. it has a memory leak when a requeste page flip is handled after
drm_events_release() is called and before drm_fb_release()
is called. At this time, a drm_pending_event will not be freed.
So also this chage releases the drm_pending_event at postclose().
And it calls drm_vblank_put() for pair if there is any unhandled page
flip event.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
|
|
Fixed a trivial typo.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
Fix a trivial typo.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This patch supports the separate handling of the USB transfer buffer length
and the length of the buffer used for multi packet support. For devices
supporting multiple report or diagnostic packets, the USB transfer size is now
limited to the USB endpoints wMaxPacketSize - otherwise it defaults to the
configured report packet size as before.
This fixes an issue where event reporting can be delayed for an arbitrary
time for multi packet devices. For instance the report size for eGalax devices
is defined to the 16 byte maximum diagnostic packet size as opposed to the 5
byte report packet size. In case the driver requests 16 byte from the USB
interrupt endpoint, the USB host controller driver needs to split up the
request into 2 accesses according to the endpoints wMaxPacketSize of 8 byte.
When the first transfer is answered by the eGalax device with not less than
the full 8 byte requested, the host controller has got no way of knowing
whether the touch controller has got additional data queued and will issue
the second transfer. If per example a liftoff event finishes at such a
wMaxPacketSize boundary, the data will not be available to the usbtouch driver
until a further event is triggered and transfered to the host. From user
perspective the BTN_TOUCH release event in this case is stuck until the next
touch down event.
Signed-off-by: Christian Engelmayer <christian.engelmayer@frequentis.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
We will never use packet_id before initializing it as we start with
"need_blobs == -1" and will set packet_id there.
Also use le32_to_cpu when fetching header->packet_id.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Remove waiting for TX queues to become empty during selftest.
This check is not necessary for any purpose, and might put
the driver into an infinite loop.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
receive mergeable now handles errors internally.
Do same for big and small packet paths, otherwise
the logic is too hard to follow.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Eric Dumazet noticed that if we encounter an error
when processing a mergeable buffer, we don't
dequeue all of the buffers from this packet,
the result is almost sure to be loss of networking.
Jason Wang noticed that we also leak a page and that we don't decrement
the rq buf count, so we won't repost buffers (a resource leak).
Fix both issues.
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Michael Dalton <mwdalton@google.com>
Reported-by: Eric Dumazet <edumazet@google.com>
Reported-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A return value of 1 is interpreted as an error. See pci_driver.
in local_pci_probe(). If you're wondering how this ever could
have worked, it's because it used to be the case that only return
values less than zero were interpreted as failure. But even in
the current kernel if the driver registers its various entry
points with the kernel, and then returns a value which is
interpreted as failure, those registrations aren't undone, so
the driver still mostly works. However, the driver's remove
function wouldn't be called on rmmod, and pci power management
functions wouldn't work. In the case of Smart Array, since it
has a battery backed cache (or else no cache) even if the driver
is not shut down properly as long as there is no outstanding
i/o, nothing too bad happens, which is why it took so long to
notice.
Requesting backport to stable because the change to pci-driver.c
which requires driver probe functions to return 0 occurred between
2.6.35 and 2.6.36 (the pci power management breakage) and again
between 3.7 and 3.8 (pci_dev->driver getting set to NULL in
local_pci_probe() preventing driver remove function from being
called on rmmod.)
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
We inadvertantly discarded the scsi status for aborted commands.
For some commands (e.g. reads from tape drives) these can't be retried,
and if we discarded the scsi status, the scsi mid layer couldn't notice
anything was wrong and the error was not reported.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
"MAC filter" sounds more reasonable than "MAC fitler".
Signed-off-by: Thomas Huth <thuth@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Correct a namespace complaint by making the function static
and moving the prototype into the .c file.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
NETIF_F_HW_L2FW_DOFFLOAD allows upper layer net devices such
as macvlan to use queues in the hardware to directly submit and
receive skbs.
This creates a subtle change in the datapath though. One change
being the skb may no longer use the root devices qdisc.
Because users may not expect this we can't enable the feature
by default unless the hardware can offload all the software
functionality above it. So for now disable it by default and
let users opt in.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When compiling with -Wstrict-prototypes gcc catches a static
I missed.
./ixgbe_main.c:4254: warning: no previous prototype for 'ixgbe_fwd_ring_down'
Reported-by: Phillip Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
On e1000_down(), we should ensure every asynchronous work is canceled
before proceeding. Since the watchdog_task can schedule other works
apart from itself, it should be stopped first, but currently it is
stopped after the reset_task. This can result in the following race
leading to the reset_task running after the module unload:
e1000_down_and_stop(): e1000_watchdog():
---------------------- -----------------
cancel_work_sync(reset_task)
schedule_work(reset_task)
cancel_delayed_work_sync(watchdog_task)
The patch moves cancel_delayed_work_sync(watchdog_task) at the beginning
of e1000_down_and_stop() thus ensuring the race is impossible.
Cc: Tushar Dave <tushar.n.dave@intel.com>
Cc: Patrick McHardy <kaber@trash.net>
Signed-off-by: Vladimir Davydov <vdavydov@parallels.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The patch fixes the following lockdep warning, which is 100%
reproducible on network restart:
======================================================
[ INFO: possible circular locking dependency detected ]
3.12.0+ #47 Tainted: GF
-------------------------------------------------------
kworker/1:1/27 is trying to acquire lock:
((&(&adapter->watchdog_task)->work)){+.+...}, at: [<ffffffff8108a5b0>] flush_work+0x0/0x70
but task is already holding lock:
(&adapter->mutex){+.+...}, at: [<ffffffffa0177c0a>] e1000_reset_task+0x4a/0xa0 [e1000]
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (&adapter->mutex){+.+...}:
[<ffffffff810bdb5d>] lock_acquire+0x9d/0x120
[<ffffffff816b8cbc>] mutex_lock_nested+0x4c/0x390
[<ffffffffa017233d>] e1000_watchdog+0x7d/0x5b0 [e1000]
[<ffffffff8108b972>] process_one_work+0x1d2/0x510
[<ffffffff8108ca80>] worker_thread+0x120/0x3a0
[<ffffffff81092c1e>] kthread+0xee/0x110
[<ffffffff816c3d7c>] ret_from_fork+0x7c/0xb0
-> #0 ((&(&adapter->watchdog_task)->work)){+.+...}:
[<ffffffff810bd9c0>] __lock_acquire+0x1710/0x1810
[<ffffffff810bdb5d>] lock_acquire+0x9d/0x120
[<ffffffff8108a5eb>] flush_work+0x3b/0x70
[<ffffffff8108b5d8>] __cancel_work_timer+0x98/0x140
[<ffffffff8108b693>] cancel_delayed_work_sync+0x13/0x20
[<ffffffffa0170cec>] e1000_down_and_stop+0x3c/0x60 [e1000]
[<ffffffffa01775b1>] e1000_down+0x131/0x220 [e1000]
[<ffffffffa0177c12>] e1000_reset_task+0x52/0xa0 [e1000]
[<ffffffff8108b972>] process_one_work+0x1d2/0x510
[<ffffffff8108ca80>] worker_thread+0x120/0x3a0
[<ffffffff81092c1e>] kthread+0xee/0x110
[<ffffffff816c3d7c>] ret_from_fork+0x7c/0xb0
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&adapter->mutex);
lock((&(&adapter->watchdog_task)->work));
lock(&adapter->mutex);
lock((&(&adapter->watchdog_task)->work));
*** DEADLOCK ***
3 locks held by kworker/1:1/27:
#0: (events){.+.+.+}, at: [<ffffffff8108b906>] process_one_work+0x166/0x510
#1: ((&adapter->reset_task)){+.+...}, at: [<ffffffff8108b906>] process_one_work+0x166/0x510
#2: (&adapter->mutex){+.+...}, at: [<ffffffffa0177c0a>] e1000_reset_task+0x4a/0xa0 [e1000]
stack backtrace:
CPU: 1 PID: 27 Comm: kworker/1:1 Tainted: GF 3.12.0+ #47
Hardware name: System manufacturer System Product Name/P5B-VM SE, BIOS 0501 05/31/2007
Workqueue: events e1000_reset_task [e1000]
ffffffff820f6000 ffff88007b9dba98 ffffffff816b54a2 0000000000000002
ffffffff820f5e50 ffff88007b9dbae8 ffffffff810ba936 ffff88007b9dbac8
ffff88007b9dbb48 ffff88007b9d8f00 ffff88007b9d8780 ffff88007b9d8f00
Call Trace:
[<ffffffff816b54a2>] dump_stack+0x49/0x5f
[<ffffffff810ba936>] print_circular_bug+0x216/0x310
[<ffffffff810bd9c0>] __lock_acquire+0x1710/0x1810
[<ffffffff8108a5b0>] ? __flush_work+0x250/0x250
[<ffffffff810bdb5d>] lock_acquire+0x9d/0x120
[<ffffffff8108a5b0>] ? __flush_work+0x250/0x250
[<ffffffff8108a5eb>] flush_work+0x3b/0x70
[<ffffffff8108a5b0>] ? __flush_work+0x250/0x250
[<ffffffff8108b5d8>] __cancel_work_timer+0x98/0x140
[<ffffffff8108b693>] cancel_delayed_work_sync+0x13/0x20
[<ffffffffa0170cec>] e1000_down_and_stop+0x3c/0x60 [e1000]
[<ffffffffa01775b1>] e1000_down+0x131/0x220 [e1000]
[<ffffffffa0177c12>] e1000_reset_task+0x52/0xa0 [e1000]
[<ffffffff8108b972>] process_one_work+0x1d2/0x510
[<ffffffff8108b906>] ? process_one_work+0x166/0x510
[<ffffffff8108ca80>] worker_thread+0x120/0x3a0
[<ffffffff8108c960>] ? manage_workers+0x2c0/0x2c0
[<ffffffff81092c1e>] kthread+0xee/0x110
[<ffffffff81092b30>] ? __init_kthread_worker+0x70/0x70
[<ffffffff816c3d7c>] ret_from_fork+0x7c/0xb0
[<ffffffff81092b30>] ? __init_kthread_worker+0x70/0x70
== The issue background ==
The problem occurs, because e1000_down(), which is called under
adapter->mutex by e1000_reset_task(), tries to synchronously cancel
e1000 auxiliary works (reset_task, watchdog_task, phy_info_task,
fifo_stall_task), which take adapter->mutex in their handlers. So the
question is what does adapter->mutex protect there?
The adapter->mutex was introduced by commit 0ef4ee ("e1000: convert to
private mutex from rtnl") as a replacement for rtnl_lock() taken in the
asynchronous handlers. It targeted on fixing a similar lockdep warning
issued when e1000_down() was called under rtnl_lock(), and it fixed it,
but unfortunately it introduced the lockdep warning described above.
Anyway, that said the source of this bug is that the asynchronous works
were made to take rtnl_lock() some time ago, so let's look deeper and
find why it was added there.
The rtnl_lock() was added to asynchronous handlers by commit 338c15
("e1000: fix occasional panic on unload") in order to prevent
asynchronous handlers from execution after the module is unloaded
(e1000_down() is called) as it follows from the comment to the commit:
> Net drivers in general have an issue where timers fired
> by mod_timer or work threads with schedule_work are running
> outside of the rtnl_lock.
>
> With no other lock protection these routines are vulnerable
> to races with driver unload or reset paths.
>
> The longer term solution to this might be a redesign with
> safer locks being taken in the driver to guarantee no
> reentrance, but for now a safe and effective fix is
> to take the rtnl_lock in these routines.
I'm not sure if this locking scheme fixed the problem or just made it
unlikely, although I incline to the latter. Anyway, this was long time
ago when e1000 auxiliary works were implemented as timers scheduling
real work handlers in their routines. The e1000_down() function only
canceled the timers, but left the real handlers running if they were
running, which could result in work execution after module unload.
Today, the e1000 driver uses sane delayed works instead of the pair
timer+work to implement its delayed asynchronous handlers, and the
e1000_down() synchronously cancels all the works so that the problem
that commit 338c15 tried to cope with disappeared, and we don't need any
locks in the handlers any more. Moreover, any locking there can
potentially result in a deadlock.
So, this patch reverts commits 0ef4ee and 338c15.
Fixes: 0ef4eedc2e98 ("e1000: convert to private mutex from rtnl")
Fixes: 338c15e470d8 ("e1000: fix occasional panic on unload")
Cc: Tushar Dave <tushar.n.dave@intel.com>
Cc: Patrick McHardy <kaber@trash.net>
Signed-off-by: Vladimir Davydov <vdavydov@parallels.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This change is based on a similar change made to e1000e support in
commit bb9e44d0d0f4 ("e1000e: prevent oops when adapter is being closed
and reset simultaneously"). The same issue has also been observed
on the older e1000 cards.
Here, we have increased the RESET_COUNT value to 50 because there are too
many accesses to e1000 nic on stress tests to e1000 nic, it is not enough
to set RESET_COUT 25. Experimentation has shown that it is enough to set
RESET_COUNT 50.
Signed-off-by: yzhu1 <yanjun.zhu@windriver.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch fixes Wake on LAN being reported as supported on some Ethernet
ports, in contrary to Hardware capability.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When user linkup is enabled and user sets linkup of individual port,
we need to recompute linkup (carrier) of master interface so the change
is reflected. Fix this by calling __team_carrier_check() which does the
needed work.
Please apply to all stable kernels as well. Thanks.
Reported-by: Jan Tluka <jtluka@redhat.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Simplify the code. Avoid race conditions caused by attributes
being created after hwmon device registration. Implicitly
(through hwmon API) add mandatory 'name' sysfs attribute.
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After commit e9e4ea74f06635f2ffc1dffe5ef40c854faa0a90
"net: smc91x: dont't use SMC_outw for fixing up halfword-aligned data"
The Versatile SMSC LAN91C111 is crashing like this:
------------[ cut here ]------------
kernel BUG at /home/linus/linux/drivers/net/ethernet/smsc/smc91x.c:599!
Internal error: Oops - BUG: 0 [#1] ARM
Modules linked in:
CPU: 0 PID: 43 Comm: udhcpc Not tainted 3.13.0-rc1+ #24
task: c6ccfaa0 ti: c6cd0000 task.ti: c6cd0000
PC is at smc_hardware_send_pkt+0x198/0x22c
LR is at smc_hardware_send_pkt+0x24/0x22c
pc : [<c01be324>] lr : [<c01be1b0>] psr: 20000013
sp : c6cd1d08 ip : 00000001 fp : 00000000
r10: c02adb08 r9 : 00000000 r8 : c6ced802
r7 : c786fba0 r6 : 00000146 r5 : c8800000 r4 : c78d6000
r3 : 0000000f r2 : 00000146 r1 : 00000000 r0 : 00000031
Flags: nzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
Control: 0005317f Table: 06cf4000 DAC: 00000015
Process udhcpc (pid: 43, stack limit = 0xc6cd01c0)
Stack: (0xc6cd1d08 to 0xc6cd2000)
1d00: 00000010 c8800000 c78d6000 c786fba0 c78d6000 c01be868
1d20: c01be7a4 00004000 00000000 c786fba0 c6c12b80 c0208554 000004d0 c780fc60
1d40: 00000220 c01fb734 00000000 00000000 00000000 c6c9a440 c6c12b80 c78d6000
1d60: c786fba0 c6c9a440 00000000 c021d1d8 00000000 00000000 c6c12b80 c78d6000
1d80: c786fba0 00000001 c6c9a440 c02087f8 c6c9a4a0 00080008 00000000 00000000
1da0: c78d6000 c786fba0 c78d6000 00000138 00000000 00000000 00000000 00000000
1dc0: 00000000 c027ba74 00000138 00000138 00000001 00000010 c6cedc00 00000000
1de0: 00000008 c7404400 c6cd1eec c6cd1f14 c067a73c c065c0b8 00000000 c067a740
1e00: 01ffffff 002040d0 00000000 00000000 00000000 00000000 00000000 ffffffff
1e20: 43004400 00110022 c6cdef20 c027ae8c c6ccfaa0 be82d65c 00000014 be82d3cc
1e40: 00000000 00000000 00000000 c01f2870 00000000 00000000 00000000 c6cd1e88
1e60: c6ccfaa0 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1e80: 00000000 00000000 00000031 c7802310 c7802300 00000138 c7404400 c0771da0
1ea0: 00000000 c6cd1eec c7800340 00000138 be82d65c 00000014 be82d3cc c6cd1f08
1ec0: 00000014 00000000 c7404400 c7404400 00000138 c01f4628 c78d6000 00000000
1ee0: 00000000 be82d3cc 00000138 c6cd1f08 00000014 c6cd1ee4 00000001 00000000
1f00: 00000000 00000000 00080011 00000002 06000000 ffffffff 0000ffff 00000002
1f20: 06000000 ffffffff 0000ffff c00928c8 c065c520 c6cd1f58 00000003 c009299c
1f40: 00000003 c065c520 c7404400 00000000 c7404400 c01f2218 c78106b0 c7441cb0
1f60: 00000000 00000006 c06799fc 00000000 00000000 00000006 00000000 c01f3ee0
1f80: 00000000 00000000 be82d678 be82d65c 00000014 00000001 00000122 c00139c8
1fa0: c6cd0000 c0013840 be82d65c 00000014 00000006 be82d3cc 00000138 00000000
1fc0: be82d65c 00000014 00000001 00000122 00000000 00000000 00018cb1 00000000
1fe0: 00003801 be82d3a8 0003a0c7 b6e9af08 60000010 00000006 00000000 00000000
[<c01be324>] (smc_hardware_send_pkt+0x198/0x22c) from [<c01be868>] (smc_hard_start_xmit+0xc4/0x1e8)
[<c01be868>] (smc_hard_start_xmit+0xc4/0x1e8) from [<c0208554>] (dev_hard_start_xmit+0x460/0x4cc)
[<c0208554>] (dev_hard_start_xmit+0x460/0x4cc) from [<c021d1d8>] (sch_direct_xmit+0x94/0x18c)
[<c021d1d8>] (sch_direct_xmit+0x94/0x18c) from [<c02087f8>] (dev_queue_xmit+0x238/0x42c)
[<c02087f8>] (dev_queue_xmit+0x238/0x42c) from [<c027ba74>] (packet_sendmsg+0xbe8/0xd28)
[<c027ba74>] (packet_sendmsg+0xbe8/0xd28) from [<c01f2870>] (sock_sendmsg+0x84/0xa8)
[<c01f2870>] (sock_sendmsg+0x84/0xa8) from [<c01f4628>] (SyS_sendto+0xb8/0xdc)
[<c01f4628>] (SyS_sendto+0xb8/0xdc) from [<c0013840>] (ret_fast_syscall+0x0/0x2c)
Code: e3130002 1a000001 e3130001 0affffcd (e7f001f2)
---[ end trace 81104fe70e8da7fe ]---
Kernel panic - not syncing: Fatal exception in interrupt
This is because the macro operations in smc91x.h defined
for Versatile are missing SMC_outsw() as used in this
commit.
The Versatile needs and uses the same accessors as the other
platforms in the first if(...) clause, just switch it to using
that and we have one problem less to worry about.
This includes a hunk of a patch from Will Deacon fixin
the other 32bit platforms as well: Innokom, Ramses, PXA,
PCM027.
Checkpatch complains about spacing, but I have opted to
follow the style of this .h-file.
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Jonathan Cameron <jic23@cam.ac.uk>
Cc: stable@vger.kernel.org
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit b268daffdcb9762ad9aa3898096570a9dd92aa9b.
I applied the wrong version of this patch, the proper version
is coming up next.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After commit e9e4ea74f06635f2ffc1dffe5ef40c854faa0a90
"net: smc91x: dont't use SMC_outw for fixing up halfword-aligned data"
The Versatile SMSC LAN91C111 is crashing like this:
------------[ cut here ]------------
kernel BUG at /home/linus/linux/drivers/net/ethernet/smsc/smc91x.c:599!
Internal error: Oops - BUG: 0 [#1] ARM
Modules linked in:
CPU: 0 PID: 43 Comm: udhcpc Not tainted 3.13.0-rc1+ #24
task: c6ccfaa0 ti: c6cd0000 task.ti: c6cd0000
PC is at smc_hardware_send_pkt+0x198/0x22c
LR is at smc_hardware_send_pkt+0x24/0x22c
pc : [<c01be324>] lr : [<c01be1b0>] psr: 20000013
sp : c6cd1d08 ip : 00000001 fp : 00000000
r10: c02adb08 r9 : 00000000 r8 : c6ced802
r7 : c786fba0 r6 : 00000146 r5 : c8800000 r4 : c78d6000
r3 : 0000000f r2 : 00000146 r1 : 00000000 r0 : 00000031
Flags: nzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
Control: 0005317f Table: 06cf4000 DAC: 00000015
Process udhcpc (pid: 43, stack limit = 0xc6cd01c0)
Stack: (0xc6cd1d08 to 0xc6cd2000)
1d00: 00000010 c8800000 c78d6000 c786fba0 c78d6000 c01be868
1d20: c01be7a4 00004000 00000000 c786fba0 c6c12b80 c0208554 000004d0 c780fc60
1d40: 00000220 c01fb734 00000000 00000000 00000000 c6c9a440 c6c12b80 c78d6000
1d60: c786fba0 c6c9a440 00000000 c021d1d8 00000000 00000000 c6c12b80 c78d6000
1d80: c786fba0 00000001 c6c9a440 c02087f8 c6c9a4a0 00080008 00000000 00000000
1da0: c78d6000 c786fba0 c78d6000 00000138 00000000 00000000 00000000 00000000
1dc0: 00000000 c027ba74 00000138 00000138 00000001 00000010 c6cedc00 00000000
1de0: 00000008 c7404400 c6cd1eec c6cd1f14 c067a73c c065c0b8 00000000 c067a740
1e00: 01ffffff 002040d0 00000000 00000000 00000000 00000000 00000000 ffffffff
1e20: 43004400 00110022 c6cdef20 c027ae8c c6ccfaa0 be82d65c 00000014 be82d3cc
1e40: 00000000 00000000 00000000 c01f2870 00000000 00000000 00000000 c6cd1e88
1e60: c6ccfaa0 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1e80: 00000000 00000000 00000031 c7802310 c7802300 00000138 c7404400 c0771da0
1ea0: 00000000 c6cd1eec c7800340 00000138 be82d65c 00000014 be82d3cc c6cd1f08
1ec0: 00000014 00000000 c7404400 c7404400 00000138 c01f4628 c78d6000 00000000
1ee0: 00000000 be82d3cc 00000138 c6cd1f08 00000014 c6cd1ee4 00000001 00000000
1f00: 00000000 00000000 00080011 00000002 06000000 ffffffff 0000ffff 00000002
1f20: 06000000 ffffffff 0000ffff c00928c8 c065c520 c6cd1f58 00000003 c009299c
1f40: 00000003 c065c520 c7404400 00000000 c7404400 c01f2218 c78106b0 c7441cb0
1f60: 00000000 00000006 c06799fc 00000000 00000000 00000006 00000000 c01f3ee0
1f80: 00000000 00000000 be82d678 be82d65c 00000014 00000001 00000122 c00139c8
1fa0: c6cd0000 c0013840 be82d65c 00000014 00000006 be82d3cc 00000138 00000000
1fc0: be82d65c 00000014 00000001 00000122 00000000 00000000 00018cb1 00000000
1fe0: 00003801 be82d3a8 0003a0c7 b6e9af08 60000010 00000006 00000000 00000000
[<c01be324>] (smc_hardware_send_pkt+0x198/0x22c) from [<c01be868>] (smc_hard_start_xmit+0xc4/0x1e8)
[<c01be868>] (smc_hard_start_xmit+0xc4/0x1e8) from [<c0208554>] (dev_hard_start_xmit+0x460/0x4cc)
[<c0208554>] (dev_hard_start_xmit+0x460/0x4cc) from [<c021d1d8>] (sch_direct_xmit+0x94/0x18c)
[<c021d1d8>] (sch_direct_xmit+0x94/0x18c) from [<c02087f8>] (dev_queue_xmit+0x238/0x42c)
[<c02087f8>] (dev_queue_xmit+0x238/0x42c) from [<c027ba74>] (packet_sendmsg+0xbe8/0xd28)
[<c027ba74>] (packet_sendmsg+0xbe8/0xd28) from [<c01f2870>] (sock_sendmsg+0x84/0xa8)
[<c01f2870>] (sock_sendmsg+0x84/0xa8) from [<c01f4628>] (SyS_sendto+0xb8/0xdc)
[<c01f4628>] (SyS_sendto+0xb8/0xdc) from [<c0013840>] (ret_fast_syscall+0x0/0x2c)
Code: e3130002 1a000001 e3130001 0affffcd (e7f001f2)
---[ end trace 81104fe70e8da7fe ]---
Kernel panic - not syncing: Fatal exception in interrupt
This is because the macro operations in smc91x.h defined
for Versatile are missing SMC_outsw() as used in this
commit.
The Versatile needs and uses the same accessors as the other
platforms in the first if(...) clause, just switch it to using
that and we have one problem less to worry about.
Checkpatch complains about spacing, but I have opted to
follow the style of this .h-file.
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Jonathan Cameron <jic23@cam.ac.uk>
Cc: Will Deacon <will.deacon@arm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Using iperf to send packets(GSO mode is on), a bug is triggered:
[ 212.672781] kernel BUG at lib/dynamic_queue_limits.c:26!
[ 212.673396] invalid opcode: 0000 [#1] SMP
[ 212.673882] Modules linked in: 8139cp(O) nls_utf8 edd fuse loop dm_mod ipv6 i2c_piix4 8139too i2c_core intel_agp joydev pcspkr hid_generic intel_gtt floppy sr_mod mii button sg cdrom ext3 jbd mbcache usbhid hid uhci_hcd ehci_hcd usbcore sd_mod usb_common crc_t10dif crct10dif_common processor thermal_sys hwmon scsi_dh_emc scsi_dh_rdac scsi_dh_hp_sw scsi_dh ata_generic ata_piix libata scsi_mod [last unloaded: 8139cp]
[ 212.676084] CPU: 0 PID: 4124 Comm: iperf Tainted: G O 3.12.0-0.7-default+ #16
[ 212.676084] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2007
[ 212.676084] task: ffff8800d83966c0 ti: ffff8800db4c8000 task.ti: ffff8800db4c8000
[ 212.676084] RIP: 0010:[<ffffffff8122e23f>] [<ffffffff8122e23f>] dql_completed+0x17f/0x190
[ 212.676084] RSP: 0018:ffff880116e03e30 EFLAGS: 00010083
[ 212.676084] RAX: 00000000000005ea RBX: 0000000000000f7c RCX: 0000000000000002
[ 212.676084] RDX: ffff880111dd0dc0 RSI: 0000000000000bd4 RDI: ffff8800db6ffcc0
[ 212.676084] RBP: ffff880116e03e48 R08: 0000000000000992 R09: 0000000000000000
[ 212.676084] R10: ffffffff8181e400 R11: 0000000000000004 R12: 000000000000000f
[ 212.676084] R13: ffff8800d94ec840 R14: ffff8800db440c80 R15: 000000000000000e
[ 212.676084] FS: 00007f6685a3c700(0000) GS:ffff880116e00000(0000) knlGS:0000000000000000
[ 212.676084] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 212.676084] CR2: 00007f6685ad6460 CR3: 00000000db714000 CR4: 00000000000006f0
[ 212.676084] Stack:
[ 212.676084] ffff8800db6ffc00 000000000000000f ffff8800d94ec840 ffff880116e03eb8
[ 212.676084] ffffffffa041509f ffff880116e03e88 0000000f16e03e88 ffff8800d94ec000
[ 212.676084] 00000bd400059858 000000050000000f ffffffff81094c36 ffff880116e03eb8
[ 212.676084] Call Trace:
[ 212.676084] <IRQ>
[ 212.676084] [<ffffffffa041509f>] cp_interrupt+0x4ef/0x590 [8139cp]
[ 212.676084] [<ffffffff81094c36>] ? ktime_get+0x56/0xd0
[ 212.676084] [<ffffffff8108cf73>] handle_irq_event_percpu+0x53/0x170
[ 212.676084] [<ffffffff8108d0cc>] handle_irq_event+0x3c/0x60
[ 212.676084] [<ffffffff8108fdb5>] handle_fasteoi_irq+0x55/0xf0
[ 212.676084] [<ffffffff810045df>] handle_irq+0x1f/0x30
[ 212.676084] [<ffffffff81003c8b>] do_IRQ+0x5b/0xe0
[ 212.676084] [<ffffffff8142beaa>] common_interrupt+0x6a/0x6a
[ 212.676084] <EOI>
[ 212.676084] [<ffffffffa0416a21>] ? cp_start_xmit+0x621/0x97c [8139cp]
[ 212.676084] [<ffffffffa0416a09>] ? cp_start_xmit+0x609/0x97c [8139cp]
[ 212.676084] [<ffffffff81378ed9>] dev_hard_start_xmit+0x2c9/0x550
[ 212.676084] [<ffffffff813960a9>] sch_direct_xmit+0x179/0x1d0
[ 212.676084] [<ffffffff813793f3>] dev_queue_xmit+0x293/0x440
[ 212.676084] [<ffffffff813b0e46>] ip_finish_output+0x236/0x450
[ 212.676084] [<ffffffff810e59e7>] ? __alloc_pages_nodemask+0x187/0xb10
[ 212.676084] [<ffffffff813b10e8>] ip_output+0x88/0x90
[ 212.676084] [<ffffffff813afa64>] ip_local_out+0x24/0x30
[ 212.676084] [<ffffffff813aff0d>] ip_queue_xmit+0x14d/0x3e0
[ 212.676084] [<ffffffff813c6fd1>] tcp_transmit_skb+0x501/0x840
[ 212.676084] [<ffffffff813c8323>] tcp_write_xmit+0x1e3/0xb20
[ 212.676084] [<ffffffff81363237>] ? skb_page_frag_refill+0x87/0xd0
[ 212.676084] [<ffffffff813c8c8b>] tcp_push_one+0x2b/0x40
[ 212.676084] [<ffffffff813bb7e6>] tcp_sendmsg+0x926/0xc90
[ 212.676084] [<ffffffff813e1d21>] inet_sendmsg+0x61/0xc0
[ 212.676084] [<ffffffff8135e861>] sock_aio_write+0x101/0x120
[ 212.676084] [<ffffffff81107cf1>] ? vma_adjust+0x2e1/0x5d0
[ 212.676084] [<ffffffff812163e0>] ? timerqueue_add+0x60/0xb0
[ 212.676084] [<ffffffff81130b60>] do_sync_write+0x60/0x90
[ 212.676084] [<ffffffff81130d44>] ? rw_verify_area+0x54/0xf0
[ 212.676084] [<ffffffff81130f66>] vfs_write+0x186/0x190
[ 212.676084] [<ffffffff811317fd>] SyS_write+0x5d/0xa0
[ 212.676084] [<ffffffff814321e2>] system_call_fastpath+0x16/0x1b
[ 212.676084] Code: ca 41 89 dc 41 29 cc 45 31 db 29 c2 41 89 c5 89 d0 45 29 c5 f7 d0 c1 e8 1f e9 43 ff ff ff 66 0f 1f 44 00 00 31 c0 e9 7b ff ff ff <0f> 0b eb fe 66 66 66 66 2e 0f 1f 84 00 00 00 00 00 c7 47 40 00
[ 212.676084] RIP [<ffffffff8122e23f>] dql_completed+0x17f/0x190
------------[ cut here ]------------
When a skb has frags, bytes_compl plus skb->len nr_frags times in cp_tx().
It's not the correct value(actually, it should plus skb->len once) and it
will trigger the BUG_ON(bytes_compl > num_queued - dql->num_completed).
So only increase bytes_compl when finish sending all frags. pkts_compl also
has a wrong value, fix it too.
It's introduced by commit 871f0d4c ("8139cp: enable bql").
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Windows driver will enable ALDPS function, but linux driver and firmware
do not have any configuration related to ALDPS function for 8168g.
So restart system to linux and remove the NIC cable, LAN enter ALDPS,
then LAN RX will be disabled.
This issue can be easily reproduced on dual boot windows and linux
system with RTL_GIGA_MAC_VER_40 chip.
Realtek said, ALDPS function can be disabled by configuring to PHY,
switch to page 0x0A43, reg0x10 bit2=0.
Signed-off-by: David Chang <dchang@suse.com>
Acked-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently macvlan will count received packets after calling each
vlans receive handler. Macvtap attempts to count the packet
yet again when the user reads the packet from the tap socket.
This code doesn't do this consistently either. Remove the
counting from macvtap and let only macvlan count received
packets.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When L_ECHONL is on, newlines are echoed regardless of the L_ECHO
state; if set, ensure accumulated echoes are flushed before finishing
the current input processing and before more output.
Cc: <stable@vger.kernel.org> # 3.12.x
Reported-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com
Tested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 updates from Martin Schwidefsky:
"One performance improvement and a few bug fixes. Two of the fixes
deal with the clock related problems we have seen on recent kernels"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/mm: handle asce-type exceptions as normal page fault
s390,time: revert direct ktime path for s390 clockevent device
s390/time,vdso: convert to the new update_vsyscall interface
s390/uaccess: add missing page table walk range check
s390/mm: optimize copy_page
s390/dasd: validate request size before building CCW/TCW request
s390/signal: always restore saved runtime instrumentation psw bit
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"Some easy but needed fixes for i2c drivers since rc1"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: bcm2835: Linking platform nodes to adapter nodes
i2c: omap: raw read and write endian fix
i2c: i2c-bcm-kona: Fix module build
i2c: i2c-diolan-u2c: different usb endpoints for DLN-2-U2C
i2c: bcm-kona: remove duplicated include
i2c: davinci: raw read and write endian fix
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata
Pull libata fixes from Tejun Heo:
"libata device removal path was removing parent device node before its
child, which is mostly harmless but triggers warning after recent
sysfs changes. Rafael's patch fixes the order.
Other than that, minor controller-specific fixes and device ID
additions"
* 'for-3.13-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ATA: Fix port removal ordering
ahci: add Marvell 9230 to the AHCI PCI device list
ata: fix acpi_bus_get_device() return value check
pata_arasan_cf: add missing clk_disable_unprepare() on error path
ahci: add support for IBM Akebono platform device
|
|
Pull drm qxl leak fix from Dave Airlie:
"As usual 5 mins after I send a trivial pull fix I find a real bug!
This fixes a memory leak and I'd like to get it into stable queue
asap"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/qxl: fix memory leak in release list handling
|
|
During the vmap() routine for the dma-buf, we first grab the pages and
then try to allocate a temporary array to pass to the vmap(). However,
the shrinker can and will reap any object that is unbound if the
allocation for the array first fails. This includes the object which we
are attempting to vmap(). The solution is to mark the object's pages as
pinned whilst we try the allocation to prevent the use-after-free
introduced by the potential shrinkage.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
The MI_PREDICATE_RESULT_2 register exits only on HSW. On other
platforms the same offset is either reserved, or contains some
other register. So write the register only on HSW.
This regression has been introduced in
commit 9435373ef8870e0a84b6fec0ad89b952bf3097fa
Author: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Date: Wed Aug 28 16:45:46 2013 -0300
drm/i915: Report enabled slices on Haswell GT3
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Add regression notice.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
The ring scratch pages don't have a PPGTT mapping, so the DERRM SRM
should target the global GTT instead.
v2: Add MI_SRM_LRM_GLOBAL_GTT define for -fixes
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
When I submitted the first patch adding these force wake functions,
Chris Wilson observed that I was using the wrong functions, so I sent
a second version of the patch to correct this problem. The problem is
that v1 was merged instead of v2.
I was able to notice the problem when running the
debugfs-forcewake-user subtest of pm_pc8 from intel-gpu-tools.
Cc: stable@vger.kernel.org
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Pstore fs expects that backends provide a unique id which could avoid
pstore making entries as duplication or denominating entries the same
name. So I combine the timestamp, part and count into id.
Signed-off-by: Madper Xie <cxie@redhat.com>
Cc: Seiji Aguchi <seiji.aguchi@hds.com>
Cc: stable@vger.kernel.org
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
|
|
Some host adapters do not pass commands through to the target disk
directly. Instead they provide an emulated target which may or may not
accurately report its capabilities. In some cases the physical device
characteristics are reported even when the host adapter is processing
commands on the device's behalf. This can lead to adapter firmware hangs
or excessive I/O errors.
This patch disables WRITE SAME for devices connected to host adapters
that provide an emulated target. Driver writers can disable WRITE SAME
by setting the no_write_same flag in the host adapter template.
[jejb: fix up rejections due to eh_deadline patch]
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
The recent be2net commit 6384a4d (adds a support for busy polling)
introduces a regression that results in kernel crash. It incorrectly
modified be_close() so napi_disable() is called only for the first queue.
This breaks a correct pairing of napi_enable/_disable for the rest
of event queues and causes a crash in subsequent be_open() call.
v2: Applied suggestions from Sathya
Fixes: 6384a4d ("be2net: add support for ndo_busy_poll")
Cc: Sathya Perla <sathya.perla@emulex.com>
Cc: Subbu Seetharaman <subbu.seetharaman@emulex.com>
Cc: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Acked-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|