Age | Commit message (Collapse) | Author |
|
Add OHCI shutdown methods to cleanly shutdown the OHCI controller on
system shutdowns and reboots. This avoids the controller continuing
to run should be soft-reboot the platform, potentially scribbling
over system memory.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Combine usb_hcd_sa1111_probe() and ohci_hcd_sa1111_drv_probe(), doing
the same for the remove methods.
Move sa1111_start_hc and sa1111_stop_hc to be located next to these
the probe/release functions, as they're only called from them.
Get rid of the /*----*/ breaker lines.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Use dev_dbg() instead, it's more friendly.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Clean up the ohci-sa1111 driver formatting to be more compliant with
current standards, and add 'static' to various function definitions
to avoid sparse complaints about undeclared functions. Remove the
unnecessary local declaration of 'usb_disabled', which can be found
instead in linux/usb.h.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Move the USB interface register definitions into the driver, rather
than keeping them in a common place.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Move the PCMCIA interface register definitions into the driver, rather
than keeping them in a common place.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Move the PS/2 interface register definitions into the driver, rather
than keeping them in a common location.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Move the handling of the 5v supply into badge4.c, removing this board
specific detail from the sa1111 ohci driver.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Add platform hooks to be called when individual sa1111 devices are
enabled and disabled. This will allow us to move some platform
specifics out of the individual drivers.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Add a .owner initializer to the sa1111 driver structures to allow
allow the modules to be associated with their driver structures.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
One patch fixes an bug in the ARM/MSM IOMMU code which returned sucess
in the unmap function even when an error occured and the other patch
adds a workaround into the AMD IOMMU driver to better handle broken IVRS
ACPI tables (this patch fixes the case when a device is not listed in
the table but actually translated by the iommu).
* 'iommu/fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/msm: Fix error handling in msm_iommu_unmap()
iommu/amd: Work around broken IVRS tables
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending
This series contains pending target bug-fixes and cleanups for v3.3-rc3
that have been addressed the past weeks in lio-core.git.
Some of the highlights include:
- Fix handling for control CDBs with data greater than PAGE_SIZE (andy)
- Use IP_FREEBIND for iscsi-target to address network portal creation
issues with systemd (dax)
- Allow PERSISTENT RESERVE IN for non-reservation holder (marco)
- Fix iblock se_dev_attrib.unmap_granularity (marco)
- Fix unsupported WRITE_SAME sense payload handling (martin)
- Add workaround for zero-length control CDB handling (nab)
- Fix discovery with INADDR_ANY and IN6ADDR_ANY_INIT (nab)
- Fix target_submit_cmd() exception handling (nab)
- Return correct ASC for unimplemented VPD pages (roland)
- Don't zero pages used for data buffers (roland)
- Fix return code of core_tpg_.*_lun (sebastian)
* '3.3-rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (26 commits)
target: Fix unsupported WRITE_SAME sense payload
iscsi: use IP_FREEBIND socket option
iblock: fix handling of large requests
target: handle empty string writes in sysfs
iscsi_target: in_aton needs linux/inet.h
target: Fix iblock se_dev_attrib.unmap_granularity
target: Fix target_submit_cmd() exception handling
target: Change target_submit_cmd() to return void
target: accept REQUEST_SENSE with 18bytes
target: Fail INQUIRY commands with EVPD==0 but PAGE CODE!=0
target: Return correct ASC for unimplemented VPD pages
iscsi-target: Fix discovery with INADDR_ANY and IN6ADDR_ANY_INIT
target: Allow control CDBs with data > 1 page
iscsi-target: Fix up a few assignments
iscsi-target: make one-bit bitfields unsigned
iscsi-target: Fix double list_add with iscsit_alloc_buffs reject
iscsi-target: Fix reject release handling in iscsit_free_cmd()
target: fix return code of core_tpg_.*_lun
target: use save/restore lock primitive in core_dec_lacl_count()
target: avoid multiple outputs in scsi_dump_inquiry()
...
|
|
Some simple md-related fixes.
1/ two small fixes to ensure we handle an interrupted resync properly.
2/ avoid loading the bitmap multiple times in dm-raid
* tag 'md-3.3-fixes' of git://neil.brown.name/md:
md: two small fixes to handling interrupt resync.
Prevent DM RAID from loading bitmap twice.
|
|
SPI bug fixes for v3.3-rc2
Minor SPI device driver changes. A rename of the pch_spi_pcidev symbol
that merely eliminates a modpost warning, and a Kconfig change to allow
the Samsung spi driver to build on EXYNOS.
* tag 'spi-for-linus' of git://git.secretlab.ca/git/linux-2.6:
spi-topcliff-pch: rename pch_spi_pcidev to pch_spi_pcidev_driver
spi: Add spi-s3c64xx driver dependency on ARCH_EXYNOS4
|
|
This fixes a memory-corrupting bug: not only does it cause the warning,
but as a result of dropping the refcount to zero, it causes the
pcmcia_socket0 device structure to be freed while it still has
references, causing slab caches corruption. A fatal oops quickly
follows this warning - often even just a 'dmesg' following the warning
causes the kernel to oops.
While testing suspend/resume on an ARM device with PCMCIA support, and a
CF card inserted, I found that after five suspend and resumes, the
kernel would complain, and shortly die after with slab corruption.
WARNING: at include/linux/kref.h:41 kobject_get+0x28/0x50()
As the message doesn't give a clue about which kobject, and the built-in
debugging in drivers/base/power/main.c happens too late, this was added
right before each get_device():
printk("%s: %p [%s] %u\n", __func__, dev, kobject_name(&dev->kobj), atomic_read(&dev->kobj.kref.refcount));
and on the 3rd s2ram cycle, the following behaviour observed:
On the 3rd suspend/resume cycle:
dpm_prepare: c1a0d998 [pcmcia_socket0] 3
dpm_suspend: c1a0d998 [pcmcia_socket0] 3
dpm_suspend_noirq: c1a0d998 [pcmcia_socket0] 3
dpm_resume_noirq: c1a0d998 [pcmcia_socket0] 3
dpm_resume: c1a0d998 [pcmcia_socket0] 3
dpm_complete: c1a0d998 [pcmcia_socket0] 2
4th:
dpm_prepare: c1a0d998 [pcmcia_socket0] 2
dpm_suspend: c1a0d998 [pcmcia_socket0] 2
dpm_suspend_noirq: c1a0d998 [pcmcia_socket0] 2
dpm_resume_noirq: c1a0d998 [pcmcia_socket0] 2
dpm_resume: c1a0d998 [pcmcia_socket0] 2
dpm_complete: c1a0d998 [pcmcia_socket0] 1
5th:
dpm_prepare: c1a0d998 [pcmcia_socket0] 1
dpm_suspend: c1a0d998 [pcmcia_socket0] 1
dpm_suspend_noirq: c1a0d998 [pcmcia_socket0] 1
dpm_resume_noirq: c1a0d998 [pcmcia_socket0] 1
dpm_resume: c1a0d998 [pcmcia_socket0] 1
dpm_complete: c1a0d998 [pcmcia_socket0] 0
------------[ cut here ]------------
WARNING: at include/linux/kref.h:41 kobject_get+0x28/0x50()
Modules linked in: ucb1x00_core
Backtrace:
[<c0212090>] (dump_backtrace+0x0/0x110) from [<c04799dc>] (dump_stack+0x18/0x1c)
[<c04799c4>] (dump_stack+0x0/0x1c) from [<c021cba0>] (warn_slowpath_common+0x50/0x68)
[<c021cb50>] (warn_slowpath_common+0x0/0x68) from [<c021cbdc>] (warn_slowpath_null+0x24/0x28)
[<c021cbb8>] (warn_slowpath_null+0x0/0x28) from [<c0335374>] (kobject_get+0x28/0x50)
[<c033534c>] (kobject_get+0x0/0x50) from [<c03804f4>] (get_device+0x1c/0x24)
[<c0388c90>] (dpm_complete+0x0/0x1a0) from [<c0389cc0>] (dpm_resume_end+0x1c/0x20)
...
Looking at commit 7b24e7988263 ("pcmcia: split up central event handler"),
the following change was made to cs.c:
return 0;
}
#endif
-
- send_event(skt, CS_EVENT_PM_RESUME, CS_EVENT_PRI_LOW);
+ if (!(skt->state & SOCKET_CARDBUS) && (skt->callback))
+ skt->callback->early_resume(skt);
return 0;
}
And the corresponding change in ds.c is from:
-static int ds_event(struct pcmcia_socket *skt, event_t event, int priority)
-{
- struct pcmcia_socket *s = pcmcia_get_socket(skt);
...
- switch (event) {
...
- case CS_EVENT_PM_RESUME:
- if (verify_cis_cache(skt) != 0) {
- dev_dbg(&skt->dev, "cis mismatch - different card\n");
- /* first, remove the card */
- ds_event(skt, CS_EVENT_CARD_REMOVAL, CS_EVENT_PRI_HIGH);
- mutex_lock(&s->ops_mutex);
- destroy_cis_cache(skt);
- kfree(skt->fake_cis);
- skt->fake_cis = NULL;
- s->functions = 0;
- mutex_unlock(&s->ops_mutex);
- /* now, add the new card */
- ds_event(skt, CS_EVENT_CARD_INSERTION,
- CS_EVENT_PRI_LOW);
- }
- break;
...
- }
- pcmcia_put_socket(s);
- return 0;
-} /* ds_event */
to:
+static int pcmcia_bus_early_resume(struct pcmcia_socket *skt)
+{
+ if (!verify_cis_cache(skt)) {
+ pcmcia_put_socket(skt);
+ return 0;
+ }
+ dev_dbg(&skt->dev, "cis mismatch - different card\n");
+ /* first, remove the card */
+ pcmcia_bus_remove(skt);
+ mutex_lock(&skt->ops_mutex);
+ destroy_cis_cache(skt);
+ kfree(skt->fake_cis);
+ skt->fake_cis = NULL;
+ skt->functions = 0;
+ mutex_unlock(&skt->ops_mutex);
+ /* now, add the new card */
+ pcmcia_bus_add(skt);
+ return 0;
+}
As can be seen, the original function called pcmcia_get_socket() and
pcmcia_put_socket() around the guts, whereas the replacement code
calls pcmcia_put_socket() only in one path. This creates an imbalance
in the refcounting.
Testing with pcmcia_put_socket() put removed shows that the bug is gone:
dpm_suspend: c1a10998 [pcmcia_socket0] 5
dpm_suspend_noirq: c1a10998 [pcmcia_socket0] 5
dpm_resume_noirq: c1a10998 [pcmcia_socket0] 5
dpm_resume: c1a10998 [pcmcia_socket0] 5
dpm_complete: c1a10998 [pcmcia_socket0] 5
Tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
In current code, pltfm->als_vmin is set to LM3530_ALS_WINDOW_mV and
pltfm->als_vmax is 0. This does not make sense. I think what we want
here is setting pltfm->als_vmax to LM3530_ALS_WINDOW_mV.
Both als_vmin and als_vmax local variables will be set to
pltfm->als_vmin and pltfm->als_vmax by a few lines latter. Thus also
remove a redundant assignment for als_vmin and als_vmax in this patch.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Shreshtha Kumar Sahu <shreshthakumar.sahu@stericsson.com>
Acked-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Tested-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
fbdev fixes for 3.3
It includes:
- compile fix for fsl-diu-fb
- fix for a suspend/resume issue in atmel_lcdfb
- fix for a suspend/resume issue in OMAP
- workaround for a hardware bug to avoid physical damage in OMAP
- really trivial dead code removal in intelfb
* tag 'fbdev-fixes-for-3.3-1' of git://github.com/schandinat/linux-2.6:
atmel_lcdfb: fix usage of CONTRAST_CTR in suspend/resume
intelfb: remove some dead code
drivers/video: compile fixes for fsl-diu-fb.c
OMAPDSS: HDMI: PHY burnout fix
OMAP: 4430SDP/Panda: add HDMI HPD gpio
OMAP: 4430SDP/Panda: setup HDMI GPIO muxes
OMAPDSS: remove wrong HDMI HPD muxing
OMAP: 4430SDP/Panda: rename HPD GPIO to CT_CP_HPD
OMAP: 4430SDP/Panda: use gpio_free_array to free HDMI gpios
OMAPDSS: use sync versions of pm_runtime_put
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Cleanups and error path fixes for the new SRP (SCSI RDMA protocol) target.
* tag 'ib-srpt-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/srpt: Don't return freed pointer from srpt_alloc_ioctx_ring()
IB/srpt: Fix ERR_PTR() vs. NULL checking confusion
IB/srpt: Remove unneeded <linux/version.h> include
IB/srpt: Use ARRAY_SIZE() instead of open-coding
IB/srpt: Use DEFINE_SPINLOCK()/LIST_HEAD()
|
|
Those lines have two copies.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Thomas Renninger <trenn@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
* 'upstream-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: wiimote: fix invalid power_supply_powers call
HID: wacom: Fix invalid power_supply_powers calls
HID: hyperv: Properly disconnect the input device
HID: usbhid: fix dead lock between open and disconect
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6:
mfd: Avoid twl6040-codec PLL reconfiguration when not needed
mfd: Store twl6040-codec mclk configuration
|
|
Analogically to d7cb3dbd1 ("HID: wacom: Fix invalid power_supply_powers
calls"), fix also the same occurence in wiimote driver.
Reported-by: przemo@firszt.eu
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
This patch fixes a bug in target-core where unsupported WRITE_SAME ops
from a target_check_write_same_discard() failure was incorrectly
returning CHECK_CONDITION w/ TCM_INVALID_CDB_FIELD sense data.
This was causing some clients to not properly fall back, so go ahead
and use the correct TCM_UNSUPPORTED_SCSI_OPCODE sense for this case.
Reported-by: Martin Svec <martin.svec@zoner.cz>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Use IP_FREEBIND socket option so that iscsi portal configuration with
explicit IP addresses can happen during boot, before network interfaces
have been assigned IPs.
This is especially important on systemd based Linux boxes where system
boot happens asynchronously and non-trivial configuration must be done
to get targetcli.service to start synchronously after the network is
configured.
Reference:
http://lists.fedoraproject.org/pipermail/devel/2011-October/158025.html
Signed-off-by: Dax Kelson <dkelson@gurulabs.com>
Cc: "Nicholas A. Bellinger" <nab@linux-iscsi.org>
Cc: "Andy Grover" <agrover@redhat.com>
Cc: "Lennart Poettering" <lennart@poettering.net>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Requesting to many bvecs upsets bio_alloc_bioset, so limit the number we ask
for to the amount it can handle.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
These are root only and we're not likely to hit the problem in practise,
but it makes the static checkers happy.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Fixes this error after a recent nfs cleanup:
drivers/target/iscsi/iscsi_target_configfs.c: In function 'lio_target_call_addnptotpg':
drivers/target/iscsi/iscsi_target_configfs.c:214:3: error: implicit declaration of function 'in6_pton' [-Werror=implicit-function-declaration]
drivers/target/iscsi/iscsi_target_configfs.c:239:3: error: implicit declaration of function 'in_aton' [-Werror=implicit-function-declaration]
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
The block layer keeps q->limits.discard_granularity in bytes, but iblock
(and the SCSI Block Limits VPD page) keep unmap_granularity in blocks.
Report the correct value when exporting block devices by dividing to
convert bytes to blocks.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch fixes a bug in target_submit_cmd() where the failure path
for transport_generic_allocate_tasks() made a direct call to
transport_send_check_condition_and_sense() and not calling the
final target_put_sess_cmd() release callback.
For transport_generic_allocate_tasks() failures, use the proper call to
transport_generic_request_failure() to handle kref_put() along
with potential internal queue full response processing.
It also makes transport_lookup_cmd_lun() failures in
target_submit_cmd() use transport_send_check_condition_and_sense() and
target_put_sess_cmd() directly to avoid se_cmd->se_dev reference in
transport_generic_request_failure() handling.
Finally it drops the out_check_cond: label and use direct reference for
allocate task failures, and per-se_device queue_full handling is
currently not supported for transport_lookup_cmd_lun() failure
descriptors due to se_device dependency.
Reported-by: Roland Dreier <roland@purestorage.com>
Cc: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Retval not very useful, and may even be harmful. Once submitted, fabrics
should expect a sense error if anything goes wrong. All fabrics checking
of this retval are useless or broken:
fc checks it just to emit more debug output.
ib_srpt trickles retval up, then it is ignored.
qla2xxx trickles it up, which then causes a bug because the abort goto
in qla_target.c thinks cmd hasn't been sent to target.
Just returning nothing is best.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
WindowsXP+BOT issues a MODE_SENSE request with page 0x1c which is not
suppoerted by target. Target rejects that command with
TCM_INVALID_CDB_FIELD, so far so good. On BOT I can't send the SENSE
response back, instead I can only reply that an error occured. The next
thing happens is a REQUEST_SENSE request with 18 bytes length. Since the
check here is more than 18 bytes I have to NACK that request as well.
This is not really required: We check for some additional room, but we
never use it. The additional length is set to 0xa so the total length is
0xa + 8 = 18 which is fine with my 18 bytes.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
1/ If a resync is aborted we should record how far we got
(recovery_cp) the last request that we know has completed
(->curr_resync_completed) rather than the last request that was
submitted (->curr_resync).
2/ When a resync aborts we still want to update the metadata with
any changes, so set MD_CHANGE_DEVS even if we 'skip'.
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
GPIO fixes for v3.3-rc2
Straight forward bug fixes in this branch. A couple of x86 gpio drivers
missing spinlock initialization, an API change fixup for the samsung driver
and a name typo fix.
* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux-2.6:
gpio: Add missing spin_lock_init in gpio-ml-ioh driver
gpio: Add missing spin_lock_init in gpio-pch driver
gpio: samsung: adapt to changes in gpio specifier translator function declaration
Correct bad gpio naming
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
One patch to fix fan detection on NCT6776F.
* tag 'hwmon-fixes-for-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (w83627ehf) Fix number of fans for NCT6776F
|
|
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
power_supply_powers calls added in 35b4c01e2 ("power_supply: add "powers" links
to self-powered HID devices") have to be called after power device is created.
This patch also fixes the second call - it has to be "ac" instead of "battery"
Signed-off-by: Przemo Firszt <przemo@firszt.eu>
Signed-off-by: Chris Bagwell <chris@cnpbagwell.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux into upstream-fixes
Sync with Linus' tree. This is necessary to have a base for
patch that fixes commit 35b4c01e29b ("power_supply: add "powers"
links to self-powered HID devices") which went in through Anton's
tree.
|
|
Rename static struct pci_driver pch_spi_pcidev to
pch_spi_pcidev_driver to get rid of warnings from modpost checks.
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
The spi-s3c64xx driver is also used on Exynos4 so update the dependency
to enable build on those platforms.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[grant.likely: relax depends to ARCH_EXYNOS instead of ARCH_EXYNOS4]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
NCT6776F can select fan input pins for fans 3 to 5 with a secondary set of
chip register bits. Check that second set of bits in addition to the first set
to detect if fans 3..5 are monitored.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: stable@vger.kernel.org # 3.0+
Acked-by: Jean Delvare <khali@linux-fr.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
arm-soc fixes for 3.3-rc
* A series of OMAP regression fixes for merge window fallout
* Two patches for Davinci, one removes some misdefined clocks, the other
is a regression fix for merge window fallout
* Two patches that makes Broadcom bcmring build again (and removes a
bunch of unused code in the process)
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: bcmring: fix build failure in mach-bcmring/arch.c
ARM: bcmring: remove unused DMA map code
ARM: davinci: update mdio bus name
ARM: OMAP2+: arch/arm/mach-omap2/smartreflex.c: add missing iounmap
ARM: OMAP2+: arch/arm/mach-omap2/devices.c: introduce missing kfree
ARM: OMAP: fix MMC2 loopback clock handling
ARM: OMAP: fix erroneous mmc2 clock change on mmc3 setup
ARM: OMAP2+: GPMC: fix device size setup
ARM: OMAP2+: timer: Fix crash due to wrong arg to __omap_dm_timer_read_counter
ARM: OMAP3: hwmod data: register dss hwmods after dss_core
ARM: OMAP2/3: PRM: fix missing plat/irqs.h build breakage
ARM: OMAP2+: io: fix compilation breakage on 2420-only configs
ARM: OMAP4: hwmod data: Add names for DMIC memory address space
ARM: OMAP3: hwmod data: add SYSC_HAS_ENAWAKEUP for dispc
ARM: OMAP2+: hwmod data: split omap2/3 dispc hwmod class
ARM: davinci: DA850: remove non-existing pll1_sysclk4-7 clocks
ARM: OMAP2: fix regulator warnings
ARM: OMAP2: fix omap3 touchbook kconfig warning
i2c: OMAP: Fix OMAP1 build error
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: i8042 - add Lenovo Ideapad U455 to 'reset' blacklist
Input: serio_raw - return proper result when serio_raw_read fails
Input: document device properties
Input: twl4030_keypad - fix comment (trivial)
Input: gpio_keys - fix struct device declared inside parameter list
Input: evdev - fix variable initialisation
|
|
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
i.MX SDMA: Fix burstsize settings
ARM: mach-shmobile: both USB DMAC instances on sh7372 are slave-only
dma: sh_dma: not all SH DMAC implementations support MEMCPY
at_hdmac: bugfix for enabling channel irq
dmaengine: fix missing 'cnt' in ?: in dmatest
|
|
* akpm:
mm: compaction: check pfn_valid when entering a new MAX_ORDER_NR_PAGES block during isolation for migration
readahead: fix pipeline break caused by block plug
kprobes: fix a memory leak in function pre_handler_kretprobe()
drivers/tty/vt/vt_ioctl.c: fix KDFONTOP 32bit compatibility layer
lkdtm: avoid calling lkdtm_do_action() with spinlock held
mm/filemap_xip.c: fix race condition in xip_file_fault()
mm/memcontrol.c: fix warning with CONFIG_NUMA=n
avr32: select generic atomic64_t support
mm: postpone migrated page mapping reset
xtensa: fix memscan()
MAINTAINERS: update lguest F: patterns
MAINTAINERS: remove staging sections
MAINTAINERS: remove iMX5 section
MAINTAINERS: update partitions block F: patterns
|
|
- Fix a regression in 16-bit Atmel NAND flash which was introduced in 3.1
- Fix breakage with MTD suspend caused by the API rework
- Fix a problem with resetting the MX28 BCH module
- A couple of other trivial fixes
* tag 'for-linus-3.3-20120204' of git://git.infradead.org/~dwmw2/mtd-3.3:
Revert "mtd: atmel_nand: optimize read/write buffer functions"
mtd: fix MTD suspend
jffs2: do not initialize variable unnecessarily
mtd: gpmi-nand bugfix: reset the BCH module when it is not MX23
mtd: nand: fix typo in comment
|
|
This reverts commit fb5427508abbd635e877fabdf55795488119c2d6.
The reason is that it breaks 16 bits NAND flash as it was reported by
Nikolaus Voss and confirmed by Eric Bénard.
Nicolas Ferre <nicolas.ferre@atmel.com> alco confirmed:
"After double checking with designers, I must admit that I misunderstood
the way of optimizing accesses to SMC. 16 bit nand is not so common
those days..."
Reported-by: Nikolaus Voss <n.voss@weinmann.de>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Cc: stable@kernel.org [3.1+]
|
|
KDFONTOP(GET) currently fails with EIO when being run in a 32bit userland
with a 64bit kernel if the font width is not 8.
This is because of the setting of the KD_FONT_FLAG_OLD flag, which makes
con_font_get return EIO in such case.
This flag should *not* be set for KDFONTOP, since it's actually the whole
point of this flag (see comment in con_font_set for instance).
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Arthur Taylor <art@ified.ca>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
lkdtm_do_action() may call sleeping functions like kmalloc(), so do not
call it with spin lock held.
Signed-off-by: WANG Cong <xiyou.wangcong@gmail.com>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <greg@kroah.com>
Reviewed-by: Dave Young <dyoung@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Do not reconfigure the PLL in case it has been configured already
with the requested parameters.
In case of different PLL configuration do only the needed changes.
This can save considerable amount of time since we can avoid the
defined protocol (with delays) for the PLL configuration.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Store the last used mclk configuration for the PLL.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|