| Age | Commit message (Collapse) | Author |
|---|
|
The natsemi chip can have a larger EEPROM attached than it itself uses for
configuration. This patch adds support for user space access to such an
EEPROM.
Signed-off-by: Mark Brown <broonie@sirena.org.uk>
Cc: Tim Hockin <thockin@hockin.org>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
This enables TX checksum offloading for the spidernet driver by default.
Signed-off-by: Jens Osterkamp <Jens.Osterkamp@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Add support for the bonding master to specify its carrier state
based upon the state of the slaves. For 802.3ad, the bond is up if
there is an active, parterned aggregator. For other modes, the bond is
up if any slaves are up. Updates driver version to 3.0.3.
Based on a patch by jamal <hadi@cyberus.ca>.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
|
|
Fix section mismatches in acenic driver:
WARNING: drivers/net/acenic.o - Section mismatch: reference to .init.data:tigon2FwText from .text between 'acenic_probe_one' (at offset 0x2409) and 'ace_interrupt'
WARNING: drivers/net/acenic.o - Section mismatch: reference to .init.data:tigon2FwRodata from .text between 'acenic_probe_one' (at offset 0x2422) and 'ace_interrupt'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
This patch reduces the message level of the RX ram full messages
from err to debug to prevent spamming the console leaving it in the
logfiles though.
From: Jens Osterkamp <Jens.Osterkamp@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Problems with link state detection have been reported several times in the
past months.
Denis Vlasenko did all the work tracking it down. Jeff Garzik suggested the
proper place for the fix.
When using the mii library, the driver needs to check mii->force_media
and set dev->state accordingly.
Signed-off-by: Roger Luethi <rl@hellgate.ch>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Initializing the b44 MAC & PCI functional blocks in the controller must
occur inside init_one(). This will allow access to the MAC registers.
The controller was being powered up in b44_open() which would not allow
access to the registers before ifconfig was up.
Philip Kohlbecher found this bug.
Signed-off-by: Gary Zambrano <zambrano@broadcom.com>
|
|
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[NETFILTER]: Rename init functions.
[TCP]: Fix RFC2465 typo.
[INET]: Introduce tunnel4/tunnel6
[NET]: deinline 200+ byte inlines in sock.h
[ECONET]: Convert away from SOCKOPS_WRAPPED
[NET]: Fix ipx/econet/appletalk/irda ioctl crashes
[NET]: Kill Documentation/networking/TODO
[TG3]: Update version and reldate
[TG3]: Skip timer code during full lock
[TG3]: Speed up SRAM access
[TG3]: Fix PHY loopback on 5700
[TG3]: Fix bug in 40-bit DMA workaround code
[TG3]: Fix probe failure due to invalid MAC address
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (67 commits)
[PATCH] powerpc: Remove oprofile spinlock backtrace code
[PATCH] powerpc: Add oprofile calltrace support to all powerpc cpus
[PATCH] powerpc: Add oprofile calltrace support
[PATCH] for_each_possible_cpu: ppc
[PATCH] for_each_possible_cpu: powerpc
[PATCH] lock PTE before updating it in 440/BookE page fault handler
[PATCH] powerpc: Kill _machine and hard-coded platform numbers
ppc: Fix compile error in arch/ppc/lib/strcase.c
[PATCH] git-powerpc: WARN was a dumb idea
[PATCH] powerpc: a couple of trivial compile warning fixes
powerpc: remove OCP references
powerpc: Make uImage default build output for MPC8540 ADS
powerpc: move math-emu over to arch/powerpc
powerpc: use memparse() for mem= command line parsing
ppc: fix strncasecmp prototype
[PATCH] powerpc: make ISA floppies work again
[PATCH] powerpc: Fix some initcall return values
[PATCH] powerpc: Workaround for pSeries RTAS bug
[PATCH] spufs: fix __init/__exit annotations
[PATCH] powerpc: add hvc backend for rtas
...
|
|
master.kernel.org:/pub/scm/linux/kernel/git/scjody/ieee1394
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/scjody/ieee1394:
ohci1394: cleanup the "Unexpected PCI resource length" warning.
sbp2: misc debug logging cleanups
sbp2: proper treatment of DID_OK
ieee1394: set read permission for parameter disable_irm
sbp2: check for ARM failure
ohci1394: clean up asynchronous and physical request filters programming
ieee1394: remove amdtp remains from ieee1394_core.h
ieee1394: remove devfs support
Signed-off-by: Jody McIntyre <scjody@modernduck.com>
sbp2: prevent unloading of 1394 low-level driver
|
|
I'm not really certain what the thinking was but the code obviously wanted to
walk processes other than just those in it's session, for purposes of do_SAK.
Just walking those tasks that don't have a session assigned sounds at the very
least incomplete.
So modify the code to kill everything in the session and anything else that
might have the tty open. Hopefully this helps if the do_SAK functionality is
ever finished.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
We already have the tasklist_lock so there is no need for us to reacquire it
with send_group_sig_info. reader/writer locks allow multiple readers and thus
recursion so the old code was ok just wastful.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
|
|
git+ssh://master.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6.git
|
|
This warning happens in practice because the resource length reported by
the chipset is too large. This is not actually a problem, so don't warn
about it. If it happens to be too small, warn about that, but with
a different message so people who are used to ignoring the old message
don't.
Signed-off-by: Jody McIntyre <scjody@modernduck.com>
|
|
- move call of scsi_print_command from sbp2_send_command to the beginning of
sbp2_queue_command to show also commands which are not sent
- put sbp2's name into scsi_print_sense
- use __FUNCTION__ in log messages
- remove a few less useful log messages and comments
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jody McIntyre <scjody@modernduck.com>
|
|
Sbp2 relied on DID_OK to be defined as 0. Always shift DID_OK into the right
position anyway, and explicitly return DID_OK together with CHECK_CONDITION.
Also comment on some #if 0 code. The patch does not change current behaviour.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jody McIntyre <scjody@modernduck.com>
|
|
No need to hide it from /sys/module/ieee1394/parameters/.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jody McIntyre <scjody@modernduck.com>
|
|
Update version to 3.55.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Skip the main timer code if interrupts are disabled in the full lock
state.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Speed up SRAM read and write functions if possible by using MMIO
instead of config. cycles. With this change, the post reset signature
done at the end of D3 power change must now be moved before the D3
power change.
IBM reported a problem on powerpc blades during ethtool self test
that was caused by the memory test taking excessively long. Config.
cycles are very slow on powerpc and the memory test can take more
than 10 seconds to complete using config. cycles. As a result, NETDEV
WATCHDOG can be triggered during self test and the chip can end up in
a funny state.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix PHY loopback failure on some 5700 devices.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Need to check the TG3_FLAG_40BIT_DMA_BUG flag in the workaround code
path instead of device flags.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some older bootcode in some devices may report 0 MAC address in
SRAM when booting up from low power state. This patch fixes the
problem by checking for a valid MAC address in SRAM and falling back
to NVRAM if necessary.
Thanks to walt <wa1ter@myrealbox.com> for reporting the problem
and helping to debug it.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Sbp2 did not check for successful registration of the lower address range
when CONFIG_IEEE1394_SBP2_PHYS_DMA was set. If hpsb_register_addrspace
failed, a "login timed-out" would occur which is misleading. Now sbp2 logs
a sensible error message.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jody McIntyre <scjody@modernduck.com>
|
|
Various cleanups of how ohci1394 programs AsynchronousRequestFilter,
PhysicalRequestFilter, and physUpperBoundOffset. In particular, do not
rewrite registers within the bus reset interrupt handler if bus resets
do not affect the registers in the first place.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jody McIntyre <scjody@modernduck.com>
|
|
since amdtp driver was deleted
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jody McIntyre <scjody@modernduck.com>
|
|
Devfs has been disabled in the last kernel releases, so let's
remove it from ieee1394core, raw1394, video1394, dv1394.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Dan Dennedy <dan@dennedy.org>
Signed-off-by: Jody McIntyre <scjody@modernduck.com>
|
|
|
|
When a new SBP-2 unit is added, sbp2 now takes a reference on the 1394
low-level driver (ohci1394 or pcilynx). This prevents the 1394 host driver
module from being unloaded, e.g. by an administrative routine cleanup of
unused kernel modules or when another 1394 driver which depends on ohci1394
is unloaded.
The reference is dropped when the SBP-2 unit was disconnected, when sbp2 is
unloaded or detached from the unit, or when addition of the SBP-2 unit failed.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jody McIntyre <scjody@modernduck.com>
|
|
* master.kernel.org:/home/rmk/linux-2.6-serial:
[SERIAL] Provide Cirrus EP93xx AMBA PL010 serial support.
[SERIAL] amba-pl010: allow platforms to specify modem control method
[SERIAL] Remove obsoleted au1x00_uart driver
[SERIAL] Small time UART configuration fix for AU1100 processor
|
|
* master.kernel.org:/pub/scm/linux/kernel/git/davej/cpufreq:
[CPUFREQ] cpufreq_conservative: keep ignore_nice_load and freq_step values when reselected
[CPUFREQ] powernow: remove private for_each_cpu_mask()
[CPUFREQ] hotplug cpu fix for powernow-k8
[PATCH] cpufreq_ondemand: add range check
[PATCH] cpufreq_ondemand: keep ignore_nice_load value when it is reselected
[PATCH] cpufreq_ondemand: Warn if it cannot run due to too long transition latency
[PATCH] cpufreq_conservative: alternative initialise approach
[PATCH] cpufreq_conservative: make for_each_cpu() safe
[PATCH] cpufreq_conservative: alter default responsiveness
[PATCH] cpufreq_conservative: aligning of codebase with ondemand
|
|
when reselected
Keep the value of ignore_nice_load and freq_step of the conservative
governor after the governor is deselected and reselected.
Signed-off-by: Mattia Dongili <malattia@linux.it>
Signed-off-by: Dave Jones <davej@redhat.com>
|
|
Fix a lot of typos. Eyeballed by jmc@ in OpenBSD.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Replace all occurences of 0xff.. in calls to function pci_set_dma_mask()
and pci_set_consistant_dma_mask() with the corresponding DMA_xBIT_MASK from
linux/dma-mapping.h.
Signed-off-by: Matthias Gehre <M.Gehre@gmx.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
They deal with wrapping correctly and are nicer to read.
Signed-off-by: Marcelo Feitoza Parisi <marcelo@feitoza.com.br>
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
They deal with wrapping correctly and are nicer to read.
Signed-off-by: Marcelo Feitoza Parisi <marcelo@feitoza.com.br>
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Cc: Jens Axboe <axboe@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
It deals with wrapping correctly and is nicer to read.
Signed-off-by: Marcelo Feitoza Parisi <marcelo@feitoza.com.br>
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
They deal with wrapping correctly and are nicer to read.
Signed-off-by: Marcelo Feitoza Parisi <marcelo@feitoza.com.br>
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Jens Axboe <axboe@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This is a conversion to make the various file_operations structs in fs/
const. Basically a regexp job, with a few manual fixups
The goal is both to increase correctness (harder to accidentally write to
shared datastructures) and reducing the false sharing of cachelines with
things that get dirty in .data (while .rodata is nicely read only and thus
cache clean)
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Mark the f_ops members of inodes as const, as well as fix the
ripple-through this causes by places that copy this f_ops and then "do
stuff" with it.
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This patch replaces for_each_cpu with for_each_possible_cpu.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This patch replaces for_each_cpu with for_each_possible_cpu.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
drivers/ide/pci/generic.c:45: warning: `ide_generic_all_on' defined but not used
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Some quick backport bits from the libata PATA work to fix things found in
the sis driver. The piix driver needs some fixes too but those are way to
large and need someone working on old IDE with time to do them.
This patch fixes the case where random bits get loaded into SIS timing
registers according to the description of the correct behaviour from
Vojtech Pavlik. It also adds the SiS5517 ATA16 chipset which is not
currently supported by the driver. Thanks to Conrad Harriss for loaning me
the machine with the 5517 chipset.
Signed-off-by: Alan Cox <alan@redhat.com>
Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
>From http://marc.theaimsgroup.com/?l=linux-kernel&m=110304128900342&w=2
AMD756 doesn't support host side cable detection. Do disk side only and
don't advice obsolete options.
Acked-by: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
A size_t can't be < 0.
(akpm: and rw_verify_area() already did that check)
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
The Coverity checker found this off-by-one error.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
