| Age | Commit message (Collapse) | Author |
|---|
|
When running a scp transfer using a USB/Ethernet adapter the following crash
happens:
$ scp test.tar.gz fabio@192.168.1.100:/home/fabio
fabio@192.168.1.100's password:
test.tar.gz 0% 0 0.0KB/s --:-- ETA
------------[ cut here ]------------
WARNING: at net/sched/sch_generic.c:255 dev_watchdog+0x2cc/0x2f0()
NETDEV WATCHDOG: eth0 (asix): transmit queue 0 timed out
Modules linked in:
Backtrace:
[<80011c94>] (dump_backtrace+0x0/0x10c) from [<804d3a5c>] (dump_stack+0x18/0x1c)
r6:000000ff r5:80412388 r4:80685dc0 r3:80696cc0
[<804d3a44>] (dump_stack+0x0/0x1c) from [<80021868>]
(warn_slowpath_common+0x54/0x6c)
[<80021814>] (warn_slowpath_common+0x0/0x6c) from [<80021924>]
(warn_slowpath_fmt+0x38/0x40)
...
Setting SDIS (Stream Disable Mode- bit 4 of USBMODE register) fixes the problem.
However, in current code CI13XXX_DISABLE_STREAMING flag is only set in udc mode,
so allow disabling streaming also in host mode.
Tested on a mx6qsabrelite board.
Suggested-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
fsl-ehci probing fails on mpc5121e:
...
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller
fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1
fsl-ehci fsl-ehci.0: Could not get controller version
fsl-ehci fsl-ehci.0: can't setup
fsl-ehci fsl-ehci.0: USB bus 1 deregistered
fsl-ehci fsl-ehci.0: init fsl-ehci.0 fail, -22
fsl-ehci: probe of fsl-ehci.0 failed with error -22
Fix it by returning appropriate version info for mpc5121, too.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit 09f6ffde (USB: EHCI: fix build error by making ChipIdea host a
normal EHCI driver) introduced a dependency on USB_EHCI_HCD for the
chipidea USB host driver, that in turns depends on USB_ARCH_HAS_EHCI.
If this symbol is not set for MXS, the MXS boards are not able to use
the chipidea driver anymore.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add default pinctrl selection to atmel-ssc driver. The pinctrl
is mandatory.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
[nicolas.ferre@atmel.com: split dtsi and driver changes]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
It is werid that qlge driver supports NETIF_F_TSO6 but
not NETIF_F_IPV6_CSUM. This also causes some kernel warning [1]
when VLAN device setups on a qlge interface.
I think the qlge hardware doesn't support NETIF_F_IPV6_CSUM,
so we have to just remove the NETIF_F_TSO6 flag.
After this patch, the TCP/IPv6 traffic becomes normal again,
no kernel warnings any more.
NOTE: I only tested it on 2.6.32 kernel, even if the upstream
kernel could fix this automatically (it is hard to track NETIF*
flags), removing it is also safe.
1. https://bugzilla.redhat.com/show_bug.cgi?id=891839
Cc: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Cc: Ron Mercer <ron.mercer@qlogic.com>
Cc: linux-driver@qlogic.com
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Acked-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull a hwmon patch from Guenter Roeck:
"Fix build error in vexpress driver"
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (vexpress) Fix build error seen if CONFIG_OF_DEVICE is not set
|
|
Merge misc fixes from Andrew Morton:
"The audit fixes have been floating around for a while - Al and Eric
aren't responding to either myself or Kees so I asked Kees to
re-review them and here they are."
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (22 commits)
lib/rbtree.c: avoid the use of non-static __always_inline
MAINTAINERS: Omar had moved
mm: compaction: partially revert capture of suitable high-order page
linux/audit.h: move ptrace.h include to kernel header
kernel/audit.c: avoid negative sleep durations
audit: catch possible NULL audit buffers
audit: create explicit AUDIT_SECCOMP event type
MAINTAINERS: fix a status pattern
MAINTAINERS: fix arch/arm/plat-omap/include/plat/omap_hwmod.h
mm: thp: acquire the anon_vma rwsem for write during split
mm: mmap: annotate vm_lock_anon_vma locking properly for lockdep
lockdep, rwsem: provide down_write_nest_lock()
arch/mn10300/Kconfig: select CONFIG_GENERIC_ATOMIC64
mm: bootmem: fix free_all_bootmem_core() with odd bitmap alignment
mm: use aligned zone start for pfn_to_bitidx calculation
fs/exec.c: work around icc miscompilation
mm: compaction: fix echo 1 > compact_memory return error issue
mm: memblock: fix wrong memmove size in memblock_merge_regions()
drivers/video/ssd1307fb.c: fix bit order bug in the byte translation function
mm: migrate: check page_count of THP before migrating
...
|
|
This was leading to a strange behaviour when using the fbcon driver on
top of this one: the letters were in the right order, but each letter
had a vertical symmetry.
This was because the addressing was right for the byte, but the
addressing of each individual bit was inverted.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Brian Lilly <brian@crystalfontz.com>
Cc: Greg Kroah-Hartman <gregkh@linux-foundation.org>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Thomas Petazzoni <thomas@free-electrons.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fix the warning
WARNING: drivers/rtc/rtc-da9055.o(.text+0xa71): Section mismatch in reference from the function da9055_rtc_probe() to the function .init.text:da9055_rtc_device_init()
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit bf4d1b5ddb78f86078ac6ae0415802d5f0c68f92 (cpuidle: support
multiple drivers) changed the number of initialized state kobjects
in cpuidle_add_state_sysfs() from device->state_count to
drv->state_count, but left device->state_count in
cpuidle_remove_state_sysfs(). The values of these two fields may be
different, in which case a NULL pointer dereference may happen in
cpuidle_remove_state_sysfs(), for example. Fix this problem by making
cpuidle_add_state_sysfs() use device->state_count too (which restores
the original behavior of it).
[rjw: Changelog]
Signed-off-by: Krzysztof Mazur <krzysiek@podlesie.net>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Some touchscreens have buggy firmware which claims
remote wakeup to be enabled after a reset. They nevertheless
crash if the feature is cleared by the host.
Add a check for reset resume before checking for
an enabled remote wakeup feature. On compliant
devices the feature must be cleared after a reset anyway.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Adding support "PSC Scanning, Magellan 800i" in cdc-acm
Very simple, but very necessary.
Suitable for all versions of the kernel > 2.6
Signed-off-by: Denis N Ladin <denladin@gmail.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Hyundai Petatel Inc. Nexpring NP10T terminal (EV-DO rev.A USB modem) ID
Signed-off-by: Denis Kaganovich <mahatma@eu.by>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
also known as Alcatel One Touch L100V LTE
The driver description files gives these names to the vendor specific
functions on this modem:
Application1: VID_1BBB&PID_011E&MI_00
Application2: VID_1BBB&PID_011E&MI_01
Modem: VID_1BBB&PID_011E&MI_03
Ethernet: VID_1BBB&PID_011E&MI_04
Reported-by: Thomas Schäfer <tschaefer@t-online.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The driver description files gives these names to the vendor specific
functions on this modem:
diag: VID_19D2&PID_0284&MI_00
nmea: VID_19D2&PID_0284&MI_01
at: VID_19D2&PID_0284&MI_02
mdm: VID_19D2&PID_0284&MI_03
net: VID_19D2&PID_0284&MI_04
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Include <linux/module.h>, so that the following errors are fixed:
drivers/usb/host/imx21-hcd.c:1929:20: error: expected declaration specifiers or '...' before string constant
drivers/usb/host/imx21-hcd.c:1930:15: error: expected declaration specifiers or '...' before string constant
drivers/usb/host/imx21-hcd.c:1931:16: error: expected declaration specifiers or '...' before string constant
drivers/usb/host/imx21-hcd.c:1932:14: error: expected declaration specifiers or '...' before string constant
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In option.c, add some new MEDIATEK PIDs support for MEDIATEK new products. This
is a MEDIATEK inc. release patch.
Signed-off-by: Quentin.Li <snowmanli88@163.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Pull intel DRM fixes from Dave Airlie:
"Just intel fixes, including getting the Ironlake systems back to the
state they were in for 3.6."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/i915: Revert shrinker changes from "Track unbound pages"
drm/i915: Use pixel size for computing linear offsets into a sprite
drm/i915: Add DEBUG messages to all intel_create_user_framebuffer error paths
drm/i915: The sprite scaler on Ironlake also support YUV planes
drm: Only evict the blocks required to create the requested hole
drm/i915: Treat crtc->mode.clock == 0 as disabled
Revert "drm/i915: no lvds quirk for Zotac ZDBOX SD ID12/ID13"
drm/i915; Only increment the user-pin-count after successfully pinning the bo
|
|
764f4e4e33d18cde4dcaf8a0d860b749c6d6d08b
(sh: clkfwk: Use shared sh_clk_div_enable/disable())
shared enable/disable funcions for div4/div6.
But new sh_clk_div_enable() didn't care sh_clk_div_set_rate()
which is required on div6 clock.
This patch fixes it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Commit 64c13330a389 ("iscsi-target: Fix bug in handling of ExpStatSN
ACK during u32 wrap-around") introduced a bug where we compare the
wrong SN against our ExpCmdSN.
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
When transport_lookup_tmr_lun() fails and we return a task management
response from target_complete_tmr_failure(), we need to call
transport_cmd_check_stop_to_fabric() to release the last ref to the
cmd after calling se_tfo->queue_tm_rsp(), or else we will never remove
the failed TMR from the session command list (and we'll end up waiting
forever when trying to tear down the session).
(nab: Fix minor compile breakage)
Signed-off-by: Roland Dreier <roland@purestorage.com>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
If a backend IO takes a really long then an initiator might abort a
command, and then when it gives up on the abort, send a LUN reset too,
all before we process any of the original command or the abort. (The
abort will wait for the backend IO to complete too)
When the backend IO final completes (or fails), the abort handling
will proceed and queue up a "return aborted status" operation. Then,
while that's still pending, the LUN reset might find the original
command still on the LUN's list of commands and try to return aborted
status again, which leads to a use-after free when the first
se_tfo->queue_status call frees the command and then the second
se_tfo->queue_status call runs.
Fix this by removing a command from the LUN state_list when we first
are about to queue aborted status; we shouldn't do anything
LUN-related after we've started returning status, so this seems like
the correct thing to do.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch fixes a regression bug introduced during v3.6.x code with
the following commit to drop transport_add_cmd_to_queue(), which
originally re-set CMD_T_ACTIVE during pending WRITE I/O submission:
commit af8772926f019b7bddd7477b8de5f3b0f12bad21
Author: Christoph Hellwig <hch@infradead.org>
Date: Sun Jul 8 15:58:49 2012 -0400
target: replace the processing thread with a TMR work queue
The following sequence happens for write commands (or any other
commands with a data out phase):
- The transport calls target_submit_cmd(), which sets CMD_T_ACTIVE in
cmd->transport_state and sets cmd->t_state to TRANSPORT_NEW_CMD.
- Things go on transport_generic_new_cmd(), which notices that the
command needs to transfer data, so it sets cmd->t_state to
TRANSPORT_WRITE_PENDING and calls transport_cmd_check_stop().
- transport_cmd_check_stop() clears CMD_T_ACTIVE in cmd->transport_state
and returns in the normal case.
- Then we continue on to call ->se_tfo->write_pending().
- The data comes back from the initiator, and the transport calls
target_execute_cmd(), which sets cmd->t_state to TRANSPORT_PROCESSING
and calls into the backend to actually write the data.
At this point, the backend might take a long time to complete the
command, since it has to do real IO. If an abort request comes in for
this command at this point, it will not wait for the command to finish
since CMD_T_ACTIVE is not set. Then when the command does finally
finish, we blow up with use-after-free.
Avoid this by setting CMD_T_ACTIVE in target_execute_cmd() so that
transport_wait_for_tasks() waits for the command to finish executing.
This matches the behavior from before commit 1389533ef944 ("target:
remove transport_generic_handle_data"), when data was signaled via
transport_generic_handle_data(), which set CMD_T_ACTIVE because it
called transport_add_cmd_to_queue().
Signed-off-by: Roland Dreier <roland@purestorage.com>
Reported-by: Martin Svec <martin.svec@zoner.cz>
Cc: Christoph Hellwig <hch@lst.de>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Clear the target role when no target is provided for
the node performing a PRLI.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Reviewed-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Acked by Robert Love <robert.w.love@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
When generating a PRLI response to an initiator, clear the
FCP_SPPF_RETRY bit in the response.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Reviewed-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Acked by Robert Love <robert.w.love@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
The compiler complained about uninitialized variables, so
use TCM_NO_SENSE here.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Cc: Nicholas Bellinger <nab@risingtidesystems.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Introduce TCM_NO_SENSE, mapping to sense code
'Not ready, no additional sense information'.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Cc: Nicholas Bellinger <nab@risingtidesystems.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Fix kernel-doc warning in iov.c:
Warning(drivers/pci/iov.c:752): No description found for parameter 'numvfs'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Sorry-by: Don Dutile <ddutile@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This driver is used on Microblaze and will be used
on Arm Zynq.
Microblaze doesn't define NO_IRQ and no IRQ is 0.
Arm still uses NO_IRQ as -1 and there is no option
to connect IRQ to irq 0.
That's why <= 0 is only one option how to find out
undefined IRQ.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Axi ethernet can't be used on PPC because it is
little endian IP and PPC is big endian.
This system can't be designed.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As part of the previous driver unload flow, whenever bnx2x is
loaded after the UNDI driver it closes all Rx traffic.
However, this leads to management traffic also being stopped until
the network interface associated with one of its functions gets loaded.
To remedy this, management traffic is re-opened once the 'cleaning'
after the previous driver ends.
Signed-off-by: Barak Witkowski <barak@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When allocating Tx queues, if for some reason
(e.g., lack of memory) allocation fails, driver will incorrectly
calculate the pointers of the various queues.
This patch repositions all pointers in such a case to point at
sequential structures in memory, allowing the bnx2x macros to
be used correctly when accessing them.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 70ac618c07 ("ptp: fixup Kconfig for two PHC drivers.") removed all
dependencies for the blackfin hardware time-stamping Kconfig entry. Hardware
time-stamping is only available on BF518 though. Since the Kconfig entry is
'default y', just updateing your kernel source and running `make defconfig` will
result in the the following build errors:
drivers/net/ethernet/adi/bfin_mac.c:694: error: implicit declaration of function ‘bfin_read_EMAC_PTP_CTL’
drivers/net/ethernet/adi/bfin_mac.c:702: error: implicit declaration of function ‘bfin_write_EMAC_PTP_FV3’
drivers/net/ethernet/adi/bfin_mac.c:712: error: implicit declaration of function ‘bfin_write_EMAC_PTP_CTL’
drivers/net/ethernet/adi/bfin_mac.c:717: error: implicit declaration of function ‘bfin_write_EMAC_PTP_FOFF’
...
This patch adds back the dependency on BF518, and since it does not make sense
to expose this config option when the blackfin MAC driver is not enabled also
restore the dependency on BFIN_MAC.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
At the moment, we check owner when we enable queue in tun.
This seems redundant and will break some valid uses
where fd is passed around: I think TUNSETOWNER is there
to prevent others from attaching to a persistent device not
owned by them. Here the fd is already attached,
enabling/disabling queue is more like read/write.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
I move the return down a line after the debugging printk.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Multiqueue tun devices support detaching a tun_file from its tun_struct
and re-attaching at a later point in time. This allows users to disable
a specific queue temporarily.
ioctl(TUNSETIFF) allows the user to specify the network interface to
attach by name. This means the user can attempt to attach to interface
"B" after detaching from interface "A".
The driver is not designed to support this so check we are re-attaching
to the right tun_struct. Failure to do so may lead to oops.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We were checking the index against the size of the relocation buffer
instead of against the last index. This fix kernel segfault when
userspace submit ill formated command stream/relocation buffer pair.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Those rn50 chip are often connected to console remoting hw and load
detection often fails with those. Just don't try to load detect and
report connect.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
Index into chunks[] array doesn't look right.
Signed-off-by: Ilija Hadzic <ihadzic@research.bell-labs.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
parser->chunks[.].kpage[.] is not always kmalloc-ed
by the parser initialization, so parser_fini should
not try to kfree it if it didn't allocate it.
This patch fixes a kernel oops that can be provoked
in UMS mode.
Signed-off-by: Ilija Hadzic <ihadzic@research.bell-labs.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
In UMS mode parser->rdev is NULL, so dereferencing
will cause an oops.
Signed-off-by: Ilija Hadzic <ihadzic@research.bell-labs.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Daniel writes:
"Pretty much all just major fixes:
- 2 pieces of duct-tape for the ilk bug.
- Sprite regression fixes from Chris.
- OOPS fix for a div-by-zero from Chris, regression due to the modeset
rework in 3.7, now brought to light by a benign change in 3.8.
- Fix interrupted bo pinning, used to work around CS coherency issues on
i830/i845 (kernel also has a w/a newly in 3.8, but pinning is more efficient if
possible)."
|
|
Pull x86 platform driver bugfixes from Matthew Garrett.
* 'for_linus' of git://cavan.codon.org.uk/platform-drivers-x86:
asus-laptop: Fix potential invalid pointer dereference
Update MAINTAINERS entry
asus-laptop: Do not call HWRS on init
sony-laptop: fix SNC buffer calls when SN06 returns Integers
samsung-laptop: Add quirk for broken acpi_video backlight on N250P
acer-wmi: add Aspire 5741G touchpad toggle key
acer-wmi: change to emit touchpad on off key
acer-wmi: fix obj is NULL but dereferenced
MAINTAINERS: change the mail address of acer-wmi/msi-laptop maintainer
|
|
This partially reverts
commit 6c085a728cf000ac1865d66f8c9b52935558b328
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Mon Aug 20 11:40:46 2012 +0200
drm/i915: Track unbound pages
Closer inspection of that patch revealed a bunch of unrelated changes
in the shrinker:
- The shrinker count is now in pages instead of objects.
- For counting the shrinkable objects the old code only looked at the
inactive list, the new code looks at all bounds objects (including
pinned ones). That is obviously in addition to the new unbound list.
- The shrinker cound is no longer scaled with
sysctl_vfs_cache_pressure. Note though that with the default tuning
value of vfs_cache_pressue = 100 this doesn't affect the shrinker
behaviour.
- When actually shrinking objects, the old code first dropped
purgeable objects, then normal (inactive) objects. Only then did it,
in a last-ditch effort idle the gpu and evict everything. The new
code omits the intermediate step of evicting normal inactive
objects.
Safe for the first change, which seems benign, and the shrinker count
scaling, which is a bit a different story, the endresult of all these
changes is that the shrinker is _much_ more likely to fall back to the
last-ditch resort of idling the gpu and evicting everything. The old
code could only do that if something else evicted lots of objects
meanwhile (since without any other changes the nr_to_scan will be
smaller than the object count).
Reverting the vfs_cache_pressure behaviour itself is a bit bogus: Only
dentry/inode object caches should scale their shrinker counts with
vfs_cache_pressure. Originally I've had that change reverted, too. But
Chris Wilson insisted that it's too bogus and shouldn't again see the
light of day.
Hence revert all these other changes and restore the old shrinker
behaviour, with the minor adjustment that we now first scan the
unbound list, then the inactive list for each object category
(purgeable or normal).
A similar patch has been tested by a few people affected by the gen4/5
hangs which started to appear in 3.7, which some people bisected to
the "drm/i915: Track unbound pages" commit. But just disabling the
unbound logic alone didn't change things at all.
Note that this patch doesn't fix the referenced bugs, it only hides
the underlying bug(s) well enough to restore pre-3.7 behaviour. The
key to achieve that is to massively reduce the likelyhood of going
into a full gpu stall and evicting everything.
v2: Reword commit message a bit, taking Chris Wilson's comment into
account.
v3: On Chris Wilson's insistency, do not reinstate the rather bogus
vfs_cache_pressure change.
Tested-by: Greg KH <gregkh@linuxfoundation.org>
Tested-by: Dave Kleikamp <dave.kleikamp@oracle.com>
References: https://bugs.freedesktop.org/show_bug.cgi?id=55984
References: https://bugs.freedesktop.org/show_bug.cgi?id=57122
References: https://bugs.freedesktop.org/show_bug.cgi?id=56916
References: https://bugs.freedesktop.org/show_bug.cgi?id=57136
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 patches from Martin Schwidefsky:
"Add the finit_module system call, fix the irq statistics in
/proc/stat, fix a s390dbf lockdep problem, a patch revert for a
problem that is not 100% understood yet, and a few patches to
fix warnings."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/pci: define read*_relaxed functions
s390/topology: export cpu_topology
s390/pm: export pm_power_off
s390/pci: define isa_dma_bridge_buggy
s390/3215: partially revert tty close handling fix
s390/irq: count cpu restart events
s390/irq: remove split irq fields from /proc/stat
s390/irq: enable irq sum accounting for /proc/stat again
s390/syscalls: wire up finit_module syscall
s390/pci: remove dead code
s390/smp: fix section mismatch for smp_add_present_cpu()
s390/debug: Fix s390dbf lockdep problem in debug_(un)register_view()
|
|
max8998_set_voltage_buck_time_sel
Use DIV_ROUND_UP to prevent truncation by integer division issue.
This ensures we return enough delay time.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
|
|
Fix:
vexpress.c: In function ‘vexpress_hwmon_name_show’:
vexpress.c:34:2: error: implicit declaration of function
‘of_get_property’ [-Werror=implicit-function-declaration]
vexpress.c:34:27: warning: initialization makes pointer from integer
without a cast [enabled by default]
vexpress.c: In function ‘vexpress_hwmon_label_show’:
vexpress.c:43:22: warning: initialization makes pointer from integer
without a cast [enabled by default]
Seen if CONFIG_OF_DEVICE is not defined. of_get_property is declared in
of.h which is only included by of_device.h if CONFIG_OF_DEVICE is defined.
of.h needs to be included directly.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp
Pull EDAC fixes from Borislav Petkov:
"Two error path fixes causing a crash and a Kconfig fix for an issue
which spilled all EDAC suboptions into the 'Device Drivers' menu."
* tag 'edac_fixes_for_3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
EDAC: Cleanup device deregistering path
EDAC: Fix EDAC Kconfig menu
EDAC: Fix kernel panic on module unloading
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem
|
|
This fixes an original bug in the sprite code that miscomputed the
source offset into a linear YUV packed framebuffer, that was magnified
into an oops with
commit 5a35e99e8162d6820013a56ad15ea8bf937af5a6
Author: Damien Lespiau <damien.lespiau@intel.com>
Date: Fri Oct 26 18:20:12 2012 +0100
drm/i915: adjust sprite base address
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.com>
Cc: Damien Lespiau <damien.lespiau@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
