summaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2012-06-07net/ethernet: ks8851_mll unregister_netdev() before freeingDan Carpenter
We added another error condition here, but if we were to hit it then we need to unregister_netdev() before doing the free_netdev(). Otherwise we would hit the BUG_ON() in free_netdev(): BUG_ON(dev->reg_state != NETREG_UNREGISTERED); Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Tested-by: Raffaele Recalcati <raffaele.recalcati@bticino.it> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-07can: c_can: Add support for Bosch D_CAN controllerAnilKumar Ch
This patch adds the support for D_CAN controller driver to the existing C_CAN driver. Bosch D_CAN controller is a full-CAN implementation which is compliant to CAN protocol version 2.0 part A and B. Bosch D_CAN user manual can be obtained from: http://www.semiconductors.bosch.de/media/en/pdf/ ipmodules_1/can/d_can_users_manual_111.pdf A new array is added for accessing the d_can registers, according to d_can controller register space. Current D_CAN implementation has following limitations, this is done to avoid large changes to the C_CAN driver. 1. Message objects are limited to 32, 16 for RX and 16 for TX. C_CAN IP supports upto 32 message objects but in case of D_CAN we can configure upto 128 message objects. 2. Using two 16bit reads/writes for accessing the 32bit D_CAN registers. 3. These patches have been tested on little endian machine, there might be some hidden endian-related issues due to the nature of the accesses (32-bit registers accessed as 2 16-bit registers). However, I do not have a big-endian D_CAN implementation to confirm. Signed-off-by: AnilKumar Ch <anilkumar@ti.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2012-06-07can: c_can: Move overlay structure to array with offset as indexAnilKumar Ch
c_can uses overlay structure for accessing c_can module registers. With this kind of implementation it is difficult to add one more ip which is similar to c_can in functionality but different register offsets. This patch changes the overlay structure implementation to an array with register offset as index. This way we can overcome the above limitation. Signed-off-by: AnilKumar Ch <anilkumar@ti.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2012-06-06Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller
2012-06-06Merge branch 'master' of git://gitorious.org/linux-can/linux-can-nextDavid S. Miller
2012-06-06Merge branch 'master' of ↵John W. Linville
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem
2012-06-06net: sierra_net: device IDs for Aircard 320U++Bjørn Mork
Adding device IDs for Aircard 320U and two other devices found in the out-of-tree version of this driver. Cc: linux@sierrawireless.com Cc: Autif Khan <autif.mlist@gmail.com> Cc: Tom Cassidy <tomas.cassidy@gmail.com> Cc: stable@vger.kernel.org Signed-off-by: Bjørn Mork <bjorn@mork.no> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-06mv643xx_eth: Fix compile error for architectures without clk.Andrew Lunn
Commit 452503ebc (ARM: Orion: Eth: Add clk/clkdev support.) broke the building of the driver on architectures which don't have clk support. In particular PPC32 Pegasos which uses this driver. Add #ifdef around the clk API usage. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-06stmmac: fix driver Kconfig when built as moduleGiuseppe CAVALLARO
This patches fixes the driver when built as dynamic module. In fact, the platform part cannot be built and the probe fails (thanks to Bob Liu that reported this bug). v2: as D. Miller suggested, it is not necessary to make the pci and the platform code mutually exclusive. Having both could also help, at built time ,to verify that all the code is validated and compiles fine. v3: removed wrong Reviewed-by from the patch Reported-by: Bob Liu <lliubbo@gmail.com> cc: Rayagond Kokatanur <rayagond@vayavyalabs.com> Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-06stmmac: fix driver's doc when run kernel-doc scriptGiuseppe CAVALLARO
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-06drivers: net: Remove casts to same typeJoe Perches
Adding casts of objects to the same type is unnecessary and confusing for a human reader. For example, this cast: int y; int *p = (int *)&y; I used the coccinelle script below to find and remove these unnecessary casts. I manually removed the conversions this script produces of casts with __force, __iomem and __user. @@ type T; T *p; @@ - (T *)p + p Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-06wireless: Remove casts to same typeJoe Perches
Adding casts of objects to the same type is unnecessary and confusing for a human reader. For example, this cast: int y; int *p = (int *)&y; I used the coccinelle script below to find and remove these unnecessary casts. I manually removed the conversions this script produces of casts with __force, __iomem and __user. @@ type T; T *p; @@ - (T *)p + p Neatened the mwifiex_deauthenticate_infra function which was doing odd things with array pointers and not using is_zero_ether_addr. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-06ethernet: Remove casts to same typeJoe Perches
Adding casts of objects to the same type is unnecessary and confusing for a human reader. For example, this cast: int y; int *p = (int *)&y; I used the coccinelle script below to find and remove these unnecessary casts. I manually removed the conversions this script produces of casts with __force, __iomem and __user. @@ type T; T *p; @@ - (T *)p + p A function in atl1e_main.c was passed a const pointer when it actually modified elements of the structure. Change the argument to a non-const pointer. A function in stmmac needed a __force to avoid a sparse warning. Added it. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-06be2net: update driver versionSathya Perla
Signed-off-by: Sathya Perla <sathya.perla@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-06be2net: do not use SCRATCHPAD registerSathya Perla
The CUST_SCRATCHPAD_CSR register is used for marking if FW cleanup is needed. This is used in a crash kernel scenario. Do no use this register as it is not available for some functions. Instead, always issue an FLR when a function is probed *except* when VFs are preset (enabled in the previous PF load). Signed-off-by: Sathya Perla <sathya.perla@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-06be2net: remove unnecessary usage of unlikely()Sathya Perla
Signed-off-by: Sathya Perla <sathya.perla@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-06be2net: fix reporting number of actual rx queuesSathya Perla
Signed-off-by: Sathya Perla <sathya.perla@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-06be2net: do not modify PCI MaxReadReq sizeSathya Perla
Setting the PCI MRRS to a value of 4096 (overriding the system decided value) had provided perf improvement in TX. But, IBM has provided feedback that on POWER platforms, this value is set by the system firmware, and drivers modifying this value can cause unpredictable results (like EEH errors.) So, backing off this change. On POWER7 platforms most slots, it seems, do get a MRRS of 4096. This patch reverts the following commit: "be2net: Modified PCI MaxReadReq size to 4096 bytes" commit 5a56eb10babbcd7b3796dc3c28c271260aa3608d. Suggested-by: Brian King <bjking1@us.ibm.com> Signed-off-by: Sathya Perla <sathya.perla@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-06be2net: cleanup be_vid_config()Sathya Perla
- get rid of 2 unused arguments to the routine and some unused code - don't use the term "vlan_tag" in place of "vid" as they are different Signed-off-by: Sathya Perla <sathya.perla@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-06be2net: don't call vid_config() when there's no vlan configSathya Perla
be_vid_config() is called from be_setup() to replay config cmds after a card reset. Skip calling it when no vlans are configured. Signed-off-by: Sathya Perla <sathya.perla@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-06ixgbe: IXGBE_RXD_STAT_VP set even with Rx stripping enabledJohn Fastabend
The hardware bit IXGBE_RXD_STAT_VP appears to be set even when Rx stripping is disabled. This results in passing frames up the stack which do not have the 802.1Q tag stripped but have the tci bits set as if it was. Working around this with a check for the feature flag bit. I would welcome any better ideas or a pointer to exactly which bits in the hardware register need to be cleared to get the IXGBE_RXD_STAT_VP bit to be set per data sheet. Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Acked-by: Alexander Duyck <alexander.h.duyck@intel.com> Tested-by: Marcus Dennis <marcusx.e.dennis@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-06-06ixgbe: fix_features rxvlan is independent of DCB and needs to be setJohn Fastabend
DCB can be used independent of if RX VLAN stripping is enabled or disabled so remove erroneous check. Also enable or disable VLAN stripping when features are applied so hardware and feature flags are in sync. CC: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Tested-by: Marcus Dennis <marcusx.e.dennis@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-06-06e1000e: test for valid check_reset_block function pointerBruce Allan
commit 44abd5c12767a8c567dc4e45fd9aec3b13ca85e0 introduced NULL pointer dereferences when attempting to access the check_reset_block function pointer on 8257x and 80003es2lan non-copper devices. This fix should be applied back through 3.4. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-06-05gianfar_ethtool: coding style and whitespace cleanupsJan Ceuleers
Signed-off-by: Jan Ceuleers <jan.ceuleers@computer.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-05gianfar: Remove superfluous initialisationsJan Ceuleers
Signed-off-by: Jan Ceuleers <jan.ceuleers@computer.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-05gianfar: various coding style and whitespace cleanupsJan Ceuleers
Signed-off-by: Jan Ceuleers <jan.ceuleers@computer.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-05gianfar: comment cleanupJan Ceuleers
Signed-off-by: Jan Ceuleers <jan.ceuleers@computer.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-05gianfar: whitespace cleanup - pointers and multiplicationsJan Ceuleers
Signed-off-by: Jan Ceuleers <jan.ceuleers@computer.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-05iwlwifi: unregister LEDs if mac80211 registration failsJohannes Berg
Otherwise the LEDs stick around and cause issues the next time around since they're still there but not really hooked up. Cc: stable@kernel.org Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-05iwlwifi: fix double free/complete in firmware loadingJohannes Berg
Linus reported that due to mac80211 failing to register the device (due to WoWLAN) his machine crashed etc. as we double-freed the vmalloc() firmware area. His patch to fix it was very similar to this one but I noticed that there's another bug in the area: we complete the completion before starting, so since we're running in a work struct context stop() could be called while in the middle of start() which will almost certainly lead to issues. Make a modification similar to his to avoid the double- free but also move the completion to another spot so it is only done after start() either finished or failed so that stop() can have a consistent state. Reported-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-04iwlwifi: disable WoWLAN if !CONFIG_PM_SLEEPJohannes Berg
If CONFIG_PM_SLEEP is disabled, then iwlwifi doesn't support suspend/resume handlers and thus mac80211 (correctly) refuses advertising WoWLAN. Disable WoWLAN in the driver in this case. Cc: stable@kernel.org Reported-by: Sebastian Kemper <sebastian_ml@gmx.net> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-04bcma: add ext PA workaround for BCM4331 and BCM43431Seth Forshee
MacBook Pro models with BCM4331 wireless have been found to have the ext PA lines disabled after resuming from S3 without external power attach. This causes them to be unable to transmit. Add a workaround to ensure that the ext PA lines are enabled on BCM4331. Also extend all handling of ext PA line muxing to BCM43431 as is done in the Broadcom SDK. BugLink: http://bugs.launchpad.net/bugs/925577 Cc: Arend van Spriel <arend@broadcom.com> Cc: Hauke Mehrtens <hauke@hauke-m.de> Cc: stable@vger.kernel.org Signed-off-by: Seth Forshee <seth.forshee@canonical.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-04rt2x00: use atomic variable for seqnoStanislaw Gruszka
Remove spinlock as atomic_t can be used instead. Note we use only 16 lower bits, upper bits are changed but we impilcilty cast to u16. This fix possible deadlock on IBSS mode reproted by lockdep: ================================= [ INFO: inconsistent lock state ] 3.4.0-wl+ #4 Not tainted --------------------------------- inconsistent {IN-SOFTIRQ-W} -> {SOFTIRQ-ON-W} usage. kworker/u:2/30374 [HC0[0]:SC0[0]:HE1:SE1] takes: (&(&intf->seqlock)->rlock){+.?...}, at: [<f9979a20>] rt2x00queue_create_tx_descriptor+0x380/0x490 [rt2x00lib] {IN-SOFTIRQ-W} state was registered at: [<c04978ab>] __lock_acquire+0x47b/0x1050 [<c0498504>] lock_acquire+0x84/0xf0 [<c0835733>] _raw_spin_lock+0x33/0x40 [<f9979a20>] rt2x00queue_create_tx_descriptor+0x380/0x490 [rt2x00lib] [<f9979f2a>] rt2x00queue_write_tx_frame+0x1a/0x300 [rt2x00lib] [<f997834f>] rt2x00mac_tx+0x7f/0x380 [rt2x00lib] [<f98fe363>] __ieee80211_tx+0x1b3/0x300 [mac80211] [<f98ffdf5>] ieee80211_tx+0x105/0x130 [mac80211] [<f99000dd>] ieee80211_xmit+0xad/0x100 [mac80211] [<f9900519>] ieee80211_subif_start_xmit+0x2d9/0x930 [mac80211] [<c0782e87>] dev_hard_start_xmit+0x307/0x660 [<c079bb71>] sch_direct_xmit+0xa1/0x1e0 [<c0784bb3>] dev_queue_xmit+0x183/0x730 [<c078c27a>] neigh_resolve_output+0xfa/0x1e0 [<c07b436a>] ip_finish_output+0x24a/0x460 [<c07b4897>] ip_output+0xb7/0x100 [<c07b2d60>] ip_local_out+0x20/0x60 [<c07e01ff>] igmpv3_sendpack+0x4f/0x60 [<c07e108f>] igmp_ifc_timer_expire+0x29f/0x330 [<c04520fc>] run_timer_softirq+0x15c/0x2f0 [<c0449e3e>] __do_softirq+0xae/0x1e0 irq event stamp: 18380437 hardirqs last enabled at (18380437): [<c0526027>] __slab_alloc.clone.3+0x67/0x5f0 hardirqs last disabled at (18380436): [<c0525ff3>] __slab_alloc.clone.3+0x33/0x5f0 softirqs last enabled at (18377616): [<c0449eb3>] __do_softirq+0x123/0x1e0 softirqs last disabled at (18377611): [<c041278d>] do_softirq+0x9d/0xe0 other info that might help us debug this: Possible unsafe locking scenario: CPU0 ---- lock(&(&intf->seqlock)->rlock); <Interrupt> lock(&(&intf->seqlock)->rlock); *** DEADLOCK *** 4 locks held by kworker/u:2/30374: #0: (wiphy_name(local->hw.wiphy)){++++.+}, at: [<c045cf99>] process_one_work+0x109/0x3f0 #1: ((&sdata->work)){+.+.+.}, at: [<c045cf99>] process_one_work+0x109/0x3f0 #2: (&ifibss->mtx){+.+.+.}, at: [<f98f005b>] ieee80211_ibss_work+0x1b/0x470 [mac80211] #3: (&intf->beacon_skb_mutex){+.+...}, at: [<f997a644>] rt2x00queue_update_beacon+0x24/0x50 [rt2x00lib] stack backtrace: Pid: 30374, comm: kworker/u:2 Not tainted 3.4.0-wl+ #4 Call Trace: [<c04962a6>] print_usage_bug+0x1f6/0x220 [<c0496a12>] mark_lock+0x2c2/0x300 [<c0495ff0>] ? check_usage_forwards+0xc0/0xc0 [<c04978ec>] __lock_acquire+0x4bc/0x1050 [<c0527890>] ? __kmalloc_track_caller+0x1c0/0x1d0 [<c0777fb6>] ? copy_skb_header+0x26/0x90 [<c0498504>] lock_acquire+0x84/0xf0 [<f9979a20>] ? rt2x00queue_create_tx_descriptor+0x380/0x490 [rt2x00lib] [<c0835733>] _raw_spin_lock+0x33/0x40 [<f9979a20>] ? rt2x00queue_create_tx_descriptor+0x380/0x490 [rt2x00lib] [<f9979a20>] rt2x00queue_create_tx_descriptor+0x380/0x490 [rt2x00lib] [<f997a5cf>] rt2x00queue_update_beacon_locked+0x5f/0xb0 [rt2x00lib] [<f997a64d>] rt2x00queue_update_beacon+0x2d/0x50 [rt2x00lib] [<f9977e3a>] rt2x00mac_bss_info_changed+0x1ca/0x200 [rt2x00lib] [<f9977c70>] ? rt2x00mac_remove_interface+0x70/0x70 [rt2x00lib] [<f98e4dd0>] ieee80211_bss_info_change_notify+0xe0/0x1d0 [mac80211] [<f98ef7b8>] __ieee80211_sta_join_ibss+0x3b8/0x610 [mac80211] [<c0496ab4>] ? mark_held_locks+0x64/0xc0 [<c0440012>] ? virt_efi_query_capsule_caps+0x12/0x50 [<f98efb09>] ieee80211_sta_join_ibss+0xf9/0x140 [mac80211] [<f98f0456>] ieee80211_ibss_work+0x416/0x470 [mac80211] [<c0496d8b>] ? trace_hardirqs_on+0xb/0x10 [<c077683b>] ? skb_dequeue+0x4b/0x70 [<f98f207f>] ieee80211_iface_work+0x13f/0x230 [mac80211] [<c045cf99>] ? process_one_work+0x109/0x3f0 [<c045d015>] process_one_work+0x185/0x3f0 [<c045cf99>] ? process_one_work+0x109/0x3f0 [<f98f1f40>] ? ieee80211_teardown_sdata+0xa0/0xa0 [mac80211] [<c045ed86>] worker_thread+0x116/0x270 [<c045ec70>] ? manage_workers+0x1e0/0x1e0 [<c0462f64>] kthread+0x84/0x90 [<c0462ee0>] ? __init_kthread_worker+0x60/0x60 [<c083d382>] kernel_thread_helper+0x6/0x10 Cc: stable@vger.kernel.org Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Helmut Schaa <helmut.schaa@googlemail.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-04brcmfmac: Fix likely misuse of | for &Joe Perches
Using | with a constant is always true. Likely this should have be &. Signed-off-by: Joe Perches <joe@perches.com> Acked-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-04mac80211_hwsim: advertise interface combinationsJohannes Berg
Enforcing interface combinations broke uses of hwsim with multiple virtual interfaces. Advertise that all combinations are possible to fix this. Reported-by: Nirav Shah <nirav.j2.shah@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-04iwlwifi: fix TX power antenna accessJohannes Berg
Since my commit iwlwifi: use valid TX/RX antenna from hw_params the config values are pure overrides, not the real values for all hardware. Therefore, the EEPROM TX power reading code checks the wrong values, it should check the hw_params values. Cc: stable@kernel.org [3.4] Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-04mwifiex: support NL80211_HIDDEN_SSID_ZERO_LEN for uAPAvinash Patil
mwifiex uAP supports NL80211_HIDDEN_SSID_ZERO_LEN type of hidden SSID only. NL80211_HIDDEN_SSID_ZERO_CONTENTS is not supported. Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Kiran Divekar <dkiran@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-04mwifiex: invalidate bss config before setting channel for uAPAvinash Patil
Mark bss_config parameters as invalid before setting AP channel. This prevents from setting invalid parameters while setting AP channel to FW. Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Kiran Divekar <dkiran@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-04stmmac: remove two useless initialisationsGiuseppe CAVALLARO
This patch removes two useless initialisations in the stmmac_rx and stmmac_tx functions. In the former, the count variable was reset twice and in the stmmac_tx we only need to increment the dirty pointer w/o setting the entry variable. v2: review the subject and comment that was not clear in my first version. Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-04net/hyperv: Use wait_event on outstanding sends during device removalHaiyang Zhang
Change the busy-waiting/udelay to wait_event on outstanding sends. Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com> Reviewed-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-04net: icplus: fix interrupt maskGiuseppe CAVALLARO
This patch fixes the interrupt mask for IC101 A/G devices and now enables the link/speed/duplex interrupts. This is done by setting the "INTR pin used" bit and cleaning all the other bits in the Register 17. Reported-by: Stuart Menefy <stuart.menefy@st.com> Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-04Merge branch 'master' of git://gitorious.org/linux-can/linux-canDavid S. Miller
2012-06-04net/ethernet: ks8851_mll mac address configuration support addedRaffaele Recalcati
Signed-off-by: Raffaele Recalcati <raffaele.recalcati@bticino.it> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-03can: cc770: Fix likely misuse of | for &Joe Perches
Using | with a constant is always true. Likely this should have be &. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2012-06-03can: c_can: fix race condition in c_can_open()AnilKumar Ch
Fix the issue of C_CAN interrupts getting disabled forever when canconfig utility is used multiple times. According to NAPI usage we disable all the hardware interrupts in ISR and re-enable them in poll(). Current implementation calls napi_enable() after hardware interrupts are enabled. If we get any interrupts between these two steps then we do not process those interrupts because napi is not enabled. Mostly these interrupts come because of STATUS is not 0x7 or ERROR interrupts. If napi_enable() happens before HW interrupts enabled then c_can_poll() function will be called eventual re-enabling. This patch moves the napi_enable() call before interrupts enabled. Cc: stable@kernel.org # 2.6.39+ Signed-off-by: AnilKumar Ch <anilkumar@ti.com> Acked-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2012-06-03can: c_can: fix an interrupt thrash issue with c_can driverAnilKumar Ch
This patch fixes an interrupt thrash issue with c_can driver. In c_can_isr() function interrupts are disabled and enabled only in c_can_poll() function. c_can_isr() & c_can_poll() both read the irqstatus flag. However, irqstatus is always read as 0 in c_can_poll() because all C_CAN interrupts are disabled in c_can_isr(). This causes all interrupts to be re-enabled in c_can_poll() which in turn causes another interrupt since the event is not really handled. This keeps happening causing a flood of interrupts. To fix this, read the irqstatus register in isr and use the same cached value in the poll function. Cc: stable@kernel.org # 2.6.39+ Signed-off-by: AnilKumar Ch <anilkumar@ti.com> Acked-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2012-06-03can: c_can: fix "BUG! echo_skb is occupied!" during transmitAnilKumar Ch
This patch fixes an issue with transmit routine, which causes "can_put_echo_skb: BUG! echo_skb is occupied!" message when using "cansequence -p" on D_CAN controller. In c_can driver, while transmitting packets tx_echo flag holds the no of can frames put for transmission into the hardware. As the comment above c_can_do_tx() indicates, if we find any packet which is not transmitted then we should stop looking for more. In the current implementation this is not taken care of causing the said message. Also, fix the condition used to find if the packet is transmitted or not. Current code skips the first tx message object and ends up checking one extra invalid object. While at it, fix the comment on top of c_can_do_tx() to use the terminology "packet" instead of "package" since it is more standard. Cc: stable@kernel.org # 2.6.39+ Signed-off-by: AnilKumar Ch <anilkumar@ti.com> Acked-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2012-06-03Merge tag 'dm-3.5-changes-1' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm Pull device-mapper updates from Alasdair G Kergon: "Improve multipath's retrying mechanism in some defined circumstances and provide a simple reserve/release mechanism for userspace tools to access thin provisioning metadata while the pool is in use." * tag 'dm-3.5-changes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm: dm thin: provide userspace access to pool metadata dm thin: use slab mempools dm mpath: allow ioctls to trigger pg init dm mpath: delay retry of bypassed pg dm mpath: reduce size of struct multipath
2012-06-02dm thin: provide userspace access to pool metadataJoe Thornber
This patch implements two new messages that can be sent to the thin pool target allowing it to take a snapshot of the _metadata_. This, read-only snapshot can be accessed by userland, concurrently with the live target. Only one metadata snapshot can be held at a time. The pool's status line will give the block location for the current msnap. Since version 0.1.5 of the userland thin provisioning tools, the thin_dump program displays the msnap as follows: thin_dump -m <msnap root> <metadata dev> Available here: https://github.com/jthornber/thin-provisioning-tools Now that userland can access the metadata we can do various things that have traditionally been kernel side tasks: i) Incremental backups. By using metadata snapshots we can work out what blocks have changed over time. Combined with data snapshots we can ensure the data doesn't change while we back it up. A short proof of concept script can be found here: https://github.com/jthornber/thinp-test-suite/blob/master/incremental_backup_example.rb ii) Migration of thin devices from one pool to another. iii) Merging snapshots back into an external origin. iv) Asyncronous replication. Signed-off-by: Joe Thornber <ejt@redhat.com> Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2012-06-02dm thin: use slab mempoolsMike Snitzer
Use dedicated caches prefixed with a "dm_" name rather than relying on kmalloc mempools backed by generic slab caches so the memory usage of thin provisioning (and any leaks) can be accounted for independently. Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Alasdair G Kergon <agk@redhat.com>