Age | Commit message (Collapse) | Author |
|
Based on a patch from Linus Walleij.
Add dmaengine based support for DMA to the MMCI driver, using the
Primecell DMA engine interface. The changes over Linus' driver are:
- rename txsize_threshold to dmasize_threshold, as this reflects the
purpose more.
- use 'mmci_dma_' as the function prefix rather than 'dma_mmci_'.
- clean up requesting of dma channels.
- don't release a single channel twice when it's shared between tx and rx.
- get rid of 'dma_enable' bool - instead check whether the channel is NULL.
- detect incomplete DMA at the end of a transfer. Some DMA controllers
(eg, PL08x) are unable to be configured for scatter DMA and also listen
to all four DMA request signals [BREQ,SREQ,LBREQ,LSREQ] from the MMCI.
They can do one or other but not both. As MMCI uses LBREQ/LSREQ for the
final burst/words, PL08x does not transfer the last few words.
- map and unmap DMA buffers using the DMA engine struct device, not the
MMCI struct device - the DMA engine is doing the DMA transfer, not us.
- avoid double-unmapping of the DMA buffers on MMCI data errors.
- don't check for negative values from the dmaengine tx submission
function - Dan says this must never fail.
- use new dmaengine helper functions rather than using the ugly function
pointers directly.
- allow DMA code to be fully optimized away using dma_inprogress() which
is defined to constant 0 if DMA engine support is disabled.
- request maximum segment size from the DMA engine struct device and
set this appropriately.
- removed checking of buffer alignment - the DMA engine should deal with
its own restrictions on buffer alignment, not the individual DMA engine
users.
- removed setting DMAREQCTL - this confuses some DMA controllers as it
causes LBREQ to be asserted for the last seven transfers, rather than
six SREQ and one LSREQ.
- removed burst setting - the DMA controller should not burst past the
transfer size required to complete the DMA operation.
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
We don't need to store the number of bytes transferred in our host
structure - we can store this directly in data->bytes_xfered.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
We don't need to switch to data available interrupts if there's at
least half a FIFO depth worth of data remaining, as we'll still get
the FIFO half full interrupt. Keep this interrupt masked off until
we have less than half the FIFO depth worth of data remaining.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The sg_miter API provides the required cache maintainence, so we don't
need to do that ourselves. Remove the unnecessary additional cache
maintainence.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The data counter counts the number of bytes transferred on the MMC bus.
When a FIFO overrun occurs, we will not have transferred a FIFOs-worth
of data to memory, and so the data counter will be a FIFOs-worth ahead.
If this occurs on a block boundary, we will report one too many sectors
as successful. Fix this.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
We should not report incomplete blocks on error. Return the number of
bytes successfully transferred, rounded down to the nearest block.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
When we encounter an error, make sure we complete the transaction
otherwise we'll leave the request dangling.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The MMCIDATACNT register contain the number of byte left at error
not the number of words, so loose the << 2 thing. Further if CRC
fails on the first block, we may end up with a negative number
of transferred bytes which is not good, and the formula was in
wrong order.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc:
mmc: bfin_sdh: fix alloc size for private data
mmc: sdhci-s3c: add platform_8bit_width() hook
mmc: jz4740: don't treat NULL clk as an error
mmc: mmci: don't read command response when invalid
mmc: ushc: Remove duplicate include of usb.h
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (43 commits)
bnx2: Eliminate AER error messages on systems not supporting it
cnic: Fix big endian bug
xfrm6: Don't forget to propagate peer into ipsec route.
tg3: Use new VLAN code
bonding: update documentation - alternate configuration.
TCP: fix a bug that triggers large number of TCP RST by mistake
MAINTAINERS: remove Reinette Chatre as iwlwifi maintainer
rt2x00: add device id for windy31 usb device
mac80211: fix a crash in ieee80211_beacon_get_tim on change_interface
ipv6: Revert 'administrative down' address handling changes.
textsearch: doc - fix spelling in lib/textsearch.c.
USB NET KL5KUSB101: Fix mem leak in error path of kaweth_download_firmware()
pch_gbe: don't use flush_scheduled_work()
bnx2: Always set ETH_FLAG_TXVLAN
net: clear heap allocation for ethtool_get_regs()
ipv6: Always clone offlink routes.
dcbnl: make get_app handling symmetric for IEEE and CEE DCBx
tcp: fix bug in listening_get_next()
inetpeer: Use correct AVL tree base pointer in inet_getpeer().
GRO: fix merging a paged skb after non-paged skbs
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/staging
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/staging:
hwmon: (lis3) turn down the no IRQ message
hwmon: (asus_atk0110) Override interface detection on Sabertooth X58
hwmon: (applesmc) Properly initialize lockdep attributes
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6
* 'pm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6:
PM / Runtime: Don't enable interrupts while running in_interrupt
|
|
On PPC for example, AER is not supported and we see unnecessary AER
error message without this patch:
bnx2 0003:01:00.1: pci_cleanup_aer_uncorrect_error_status failed 0xfffffffb
Reported-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The chip's page tables did not set up properly on big endian machines,
causing EEH errors on PPC machines.
Reported-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch pivots the tg3 driver to the new VLAN infrastructure.
All references to vlgrp have been removed. The driver still attempts to
disable VLAN tag stripping if CONFIG_VLAN_8021Q or
CONFIG_VLAN_8021Q_MODULE is not defined.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: wacom - pass touch resolution to clients through input_absinfo
Input: wacom - add 2 Bamboo Pen and touch models
Input: sysrq - ensure sysrq_enabled and __sysrq_enabled are consistent
Input: sparse-keymap - fix KEY_VSW handling in sparse_keymap_setup
Input: tegra-kbc - add tegra keyboard driver
Input: gpio_keys - switch to using request_any_context_irq
Input: serio - allow registered drivers to get status flag
Input: ct82710c - return proper error code for ct82c710_open
Input: bu21013_ts - added regulator support
Input: bu21013_ts - remove duplicate resolution parameters
Input: tnetv107x-ts - don't treat NULL clk as an error
Input: tnetv107x-keypad - don't treat NULL clk as an error
Fix up trivial conflicts in drivers/input/keyboard/Makefile due to
additions of tc3589x/Tegra drivers
|
|
The bfin_sdh driver allocates the wrong size for the private data
in the mmc_host. The first parameter of mmc_alloc_host should be
the size of the local driver struct rather than the common mmc_host.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: <stable@kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
We have 8-bit width support but is not a v3 controller.
So we need platform_8bit_width() to support 8-bit buswidth.
Also we need MMC_CAP_8_BIT_DATA, so we add it in platdata.
This gets 8-bit support working again on s3c, after we previously
disabled 8-bit by default on non-v3 controllers.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
clk_get() returns a struct clk cookie to the driver and some platforms
may return NULL if they only support a single clock. clk_get() has only
failed if it returns a ERR_PTR() encoded pointer.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Don't read the command response from the registers when either the
command timed out (because there was no response from the card) or
the checksum on the response was invalid.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Including usb.h once is enough in drivers/mmc/host/ushc.c
This removes the duplicate.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Also remove fake ABS_RX/ABS_RY "axes" that were used to report physical
dimensions now that we have better way.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
The -rt patches change the console_semaphore to console_mutex. As a
result, a quite large chunk of the patches changes all
acquire/release_console_sem() to acquire/release_console_mutex()
This commit makes things use more neutral function names which dont make
implications about the underlying lock.
The only real change is the return value of console_trylock which is
inverted from try_acquire_console_sem()
This patch also paves the way to switching console_sem from a semaphore to
a mutex.
[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: make console_trylock return 1 on success, per Geert]
Signed-off-by: Torben Hohn <torbenh@gmx.de>
Cc: Thomas Gleixner <tglx@tglx.de>
Cc: Greg KH <gregkh@suse.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
setup_irq() was called before clockevents_register_device() which is
needed by the irq handler. Bug was reproducible by restarting the
kernel using kexec (reliable crash).
Signed-off-by: Nikolaus Voss <n.voss@weinmann.de>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Both pps_parport and pps_gen_parport are written in a way that they
can't share a port with any other driver. This can result in locking up
the process that loads modules or even the whole kernel if the modules
are compiled in. Use PARPORT_FLAG_EXCL to indicate this.
Signed-off-by: Alexander Gordeev <lasaine@lvk.cs.msu.su>
Cc: Alexander Gordeev <lasaine@lvk.cs.msu.su>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Rodolfo Giometti <giometti@linux.it>
Reported-by: Ingo Molnar <mingo@elte.hu>
Cc: Alexander Gordeev <lasaine@lvk.cs.msu.su>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
parport_unregister_device() should never be used when interrupts are
enabled in hardware and irq handler is registered so there is no need to
disable interrupts when using waitlist_lock. But there is no way to
explain this subtle semantics to lockdep analyzer.
So disable interrupts here too to simplify things. The price is
negligible.
Signed-off-by: Alexander Gordeev <lasaine@lvk.cs.msu.su>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Latest kernel has many changes in IRQ subsystem and its interfaces, like
adding "irq_eoi" for struct irq_chip, this patch is a follow up change
for that.
Also remove the unnecessary cast for a "void *".
Signed-off-by: Feng Tang <feng.tang@intel.com>
Cc: Alek Du <alek.du@intel.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Return PTR_ERR(led_dat->pwm) instead of 0 if pwm_request failed
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Luotao Fu <l.fu@pengutronix.de>
Cc: Reviewed-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
* 'fixes' of master.kernel.org:/home/rmk/linux-2.6-arm:
ALSA: AACI: fix timeout duration
ALSA: AACI: fix timeout condition checking
ARM: 6636/1: ep93xx: default multiplexed gpio ports to gpio mode
ARM: 6637/1: Make the argument to virt_to_phys() "const volatile"
ARM: twd: ensure timer reload is reprogrammed on entry to periodic mode
ARM: 6635/2: Configure reference clock for Versatile Express timers
ARM: versatile: name configuration options after actual board names
ARM: realview: name configuration options after actual board names
ARM: realview,vexpress: fix section mismatch warning for pen_release
ARM: 6632/3: mmci: stop using the blockend interrupts
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lethal/fbdev-2.6
* 'fbdev-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/fbdev-2.6:
mailmap: Add an entry for Axel Lin.
video: fix some comments in drivers/video/console/vgacon.c
drivers/video/bf537-lq035.c: Add missing IS_ERR test
video: pxa168fb: remove a redundant pxa168fb_check_var call
video: da8xx-fb: fix fb_probe error path
video: pxa3xx-gcu: Return -EFAULT when copy_from_user() fails
video: nuc900fb: properly free resources in nuc900fb_remove
video: nuc900fb: fix compile error
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6
* 'sh-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
sh: Fix build of sh7750 base boards
sh: update INTC to clear IRQ sense valid flag
sh: Fix sh build failure when CONFIG_SFC=m
sh: fix MSIOF0 SPI on ecovec: it conflicts with VOU
sh: support XZ-compressed kernel.
sh: Fix up breakage from asm-generic/pgtable.h changes.
|
|
GPL V2 should be GPL v2
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
busy_loop() returns negative error code, thus change err variable
from u32 to int to properly propagate correct error code.
Also remove unneeded initialization for err and i variables.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch adds the device id for the windy31 USB device to the rt73usb
driver.
Thanks to Ralf Flaxa for reporting this and providing testing and a
sample device.
Reported-by: Ralf Flaxa <rf@suse.de>
Tested-by: Ralf Flaxa <rf@suse.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch (as1445) fixes a bug in the runtime PM core left over from
the addition of the no_callbacks flag. If this flag is set then it is
possible for rpm_suspend() to be called in_interrupt, so when
releasing spinlocks it's important not to re-enable interrupts.
To avoid an unnecessary save-and-restore of the interrupt flag, the
patch also inlines a pm_request_idle() call.
This fixes Bugzilla #27482.
(The offending code was added in 2.6.37, so it's not necessary to apply
this to any earlier stable kernels.)
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: tim blechmann <tim@klingt.org>
CC: <stable@kernel.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
Turn down the no IRQ message - on some platforms that's a normal state of
affairs.
Signed-off-by: Kalhan Trisal <kalhan.trisal@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
We will leak the storage allocated by request_firmware() if the size of
the firmware is greater than KAWETH_FIRMWARE_BUF_SIZE.
This removes the leak by calling release_firmware() before we return
-ENOSPC.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Directly cancel adapter->reset_task instead of using to-be-deprecated
flush_scheduled_work().
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
TSO does not work if the VLAN tag is in the packet (non-accelerated).
We may be able to remove this restriction in future firmware.
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now vgacon_scrollback_startup() uses slab, not bootmem,
the comment above it is obsolete, so does __init_refok.
Signed-off-by: WANG Cong <amwang@redhat.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
lcd_device_register may return ERR_PTR, so a check is added for this value
before the dereference. All of the other changes reorganize the error
handling code in this function to avoid duplicating all of it in the added
case.
In the original code, in one case, the global variable fb_buffer was set to
NULL in error code that appears after this variable is initialized. This
is done now in all error handling code that has this property.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
identifier f;
@@
f(...) { ... return ERR_PTR(...); }
@@
identifier r.f, fld;
expression x;
statement S1,S2;
@@
x = f(...)
... when != IS_ERR(x)
(
if (IS_ERR(x) ||...) S1 else S2
|
*x->fld
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Current implementation calls pxa168fb_check_var twice in pxa168fb_probe.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Current implementation puts CONFIG_CPU_FREQ at wrong place, CONFIG_CPU_FREQ
is for lcd_da8xx_cpufreq_deregister not for unregister_framebuffer.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
* 'for-38-rc3' of git://codeaurora.org/quic/kernel/davidb/linux-msm:
drivers: mmc: msm: remove clock disable in probe
mmc: msm: fix dma usage not to use internal APIs
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon/kms: add new radeon_info ioctl query for clock crystal freq
drm/i915: Prevent uninitialised reads during error state capture
drm/i915: Use consistent mappings for OpRegion between ACPI and i915
drm/i915: Handle the no-interrupts case for UMS by polling
drm/i915: Disable high-precision vblank timestamping for UMS
drm/i915: Increase the amount of defense before computing vblank timestamps
drm/i915,agp/intel: Do not clear stolen entries
drm/radeon/kms: simplify atom adjust pll setup
drm/radeon/kms: match r6xx/r7xx/evergreen asic_reset with previous asics
drm/radeon/kms: make the mac rv630 quirk generic
drm/radeon/kms: fix a spelling error in an error message
drm/radeon/kms: Initialize pageflip spinlocks.
drm/i915: Recognise non-VGA display devices
drm/i915: Fix use of invalid array size for ring->sync_seqno
drm/i915/ringbuffer: Fix use of stale HEAD position whilst polling for space
drm/i915: Don't kick-off hangcheck after a DRI interrupt
drm/i915: Add dependency on CONFIG_TMPFS
drm/i915: Initialise ring vfuncs for old DRI paths
drm/i915: make the blitter report buffer modifications to the FBC unit
drm/i915: set more FBC chicken bits
|
|
git://git.pengutronix.de/git/mkl/linux-2.6
|
|
ssh://master.kernel.org/pub/scm/linux/kernel/git/ickle/drm-intel into drm-fixes
* 'drm-intel-fixes-2' of ssh://master.kernel.org/pub/scm/linux/kernel/git/ickle/drm-intel: (30 commits)
drm/i915: Prevent uninitialised reads during error state capture
drm/i915: Use consistent mappings for OpRegion between ACPI and i915
drm/i915: Handle the no-interrupts case for UMS by polling
drm/i915: Disable high-precision vblank timestamping for UMS
drm/i915: Increase the amount of defense before computing vblank timestamps
drm/i915,agp/intel: Do not clear stolen entries
Remove MAYBE_BUILD_BUG_ON
BUILD_BUG_ON: make it handle more cases
module: fix missing semicolons in MODULE macro usage
param: add null statement to compiled-in module params
module: fix linker error for MODULE_VERSION when !MODULE and CONFIG_SYSFS=n
module: show version information for built-in modules in sysfs
selinux: return -ENOMEM when memory allocation fails
tpm: fix panic caused by "tpm: Autodetect itpm devices"
TPM: Long default timeout fix
trusted keys: Fix a memory leak in trusted_update().
keys: add trusted and encrypted maintainers
encrypted-keys: rename encrypted_defined files to encrypted
trusted-keys: rename trusted_defined files to trusted
drm/i915: Recognise non-VGA display devices
...
|
|
Needed for timer queries in the 3D driver.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@gmail.com>
|