| Age | Commit message (Collapse) | Author |
|---|
|
With a low enough MSS on the link partner and TSO enabled locally, the
networking stack can periodically send a very large (e.g. 64KB) TCP
message for which the driver will attempt to use more Tx descriptors than
are available by default in the Tx ring. This is due to a workaround in
the code that imposes a limit of only 4 MSS-sized segments per descriptor
which appears to be a carry-over from the older e1000 driver and may be
applicable only to some older PCI or PCIx parts which are not supported in
e1000e. When the driver gets a message that is too large to fit across the
configured number of Tx descriptors, it stops the upper stack from queueing
any more and gets stuck in this state. After a timeout, the upper stack
assumes the adapter is hung and calls the driver to reset it.
Remove the unnecessary limitation of using up to only 4 MSS-sized segments
per Tx descriptor, and put in a hard failure test to catch when attempting
to check for message sizes larger than would fit in the whole Tx ring.
Refactor the remaining logic that limits the size of data per Tx descriptor
from a seemingly arbitrary 8KB to a limit based on the dynamic size of the
Tx packet buffer as described in the hardware specification.
Also, fix the logic in the check for space in the Tx ring for the next
largest possible packet after the current one has been successfully queued
for transmit, and use the appropriate defines for default ring sizes in
e1000_probe instead of magic values.
This issue goes back to the introduction of e1000e in 2.6.24 when it was
split off from e1000.
Reported-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Cc: Stable <stable@vger.kernel.org> [2.6.24+]
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit -
"b852b72 gianfar: fix bug caused by
87c288c6e9aa31720b72e2bc2d665e24e1653c3e"
disables by default (on mac init) the hw vlan tag insertion.
The "features" flags were not updated to reflect this, and
"ethtool -K" shows tx-vlan-offload to be "on" by default.
Cc: Sebastian Poehn <sebastian.poehn@belden.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
I'm slightly concerned by the "only in exceptional circumstances"
comment on __pskb_pull_tail but the structure of an skb just created
by netfront shouldn't hit any of the especially slow cases.
This approach still does slightly more work than the old way, since if
we pull up the entire first frag we now have to shuffle everything
down where before we just received into the right place in the first
place.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Mel Gorman <mgorman@suse.de>
Cc: xen-devel@lists.xensource.com
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Tested-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull drm fixes from Dave Airlie:
"A bunch of scattered fixes ati/intel/nouveau, couple of core ones,
nothing too shocking or different."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm: Add EDID_QUIRK_FORCE_REDUCED_BLANKING for ASUS VW222S
gma500: Consider CRTC initially active.
drm/radeon: fix dig encoder selection on DCE61
drm/radeon: fix double free in radeon_gpu_reset
drm/radeon: force dma32 to fix regression rs4xx,rs6xx,rs740
drm/radeon: rework panel mode setup
drm/radeon/atom: powergating fixes for DCE6
drm/radeon/atom: rework DIG modesetting on DCE3+
drm/radeon: don't disable plls that are in use by other crtcs
drm/radeon: add proper checking of RESOLVE_BOX command for r600-r700
drm/radeon: initialize tracked CS state
drm/radeon: fix reading CB_COLORn_MASK from the CS
drm/nvc0/copy: check PUNITS to determine which copy engines are disabled
i915: Quirk no_lvds on Gigabyte GA-D525TUD ITX motherboard
drm/i915: Use the correct size of the GTT for placing the per-process entries
drm: Check for invalid cursor flags
drm: Initialize object type when using DRM_MODE() macro
drm/i915: fix color order for BGR formats on IVB
drm/i915: fix wrong order of parameters in port checking functions
|
|
Connecting an ASUS VW222S [1] over VGA a garbled screen is shown with
vertical stripes in the top half.
In commit bc42aabc [2]
commit bc42aabc6a01b92b0f961d65671564e0e1cd7592
Author: Adam Jackson <ajax@redhat.com>
Date: Wed May 23 16:26:54 2012 -0400
drm/edid/quirks: ViewSonic VA2026w
Adam Jackson added the quirk `EDID_QUIRK_FORCE_REDUCED_BLANKING` which
is also needed for this ASUS monitor.
All log files and output from `xrandr` is included in the referenced
Bugzilla report #17629.
Please note that this monitor only has a VGA (D-Sub) connector [1].
[1] http://www.asus.com/Display/LCD_Monitors/VW222S/
[2] http://git.kernel.org/?p=linux/kernel/git/torvalds/linux.git;a=commit;h=bc42aabc6a01b92b0f961d65671564e0e1cd7592
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=17629
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Cc: <dri-devel@lists.freedesktop.org>
Cc: Adam Jackson <ajax@redhat.com>
Cc: Ian Pilcher <arequipeno@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
into drm-fixes
Alex writes:
Highlights:
- fix a gart regression on older IGP chips
- more MSAA fixes
- fix a double free in gpu reset code
- modesetting fixes
- trinity dig encoder fix.
* 'drm-fixes-3.6' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: fix dig encoder selection on DCE61
drm/radeon: fix double free in radeon_gpu_reset
drm/radeon: force dma32 to fix regression rs4xx,rs6xx,rs740
drm/radeon: rework panel mode setup
drm/radeon/atom: powergating fixes for DCE6
drm/radeon/atom: rework DIG modesetting on DCE3+
drm/radeon: don't disable plls that are in use by other crtcs
drm/radeon: add proper checking of RESOLVE_BOX command for r600-r700
drm/radeon: initialize tracked CS state
drm/radeon: fix reading CB_COLORn_MASK from the CS
|
|
[this one ideally should make 3.6 - it fixes the very annoying mode setting bug]
This causes the pipe to be forced off prior to initial mode set, which
roughly mirrors the behavior of the i915 driver. It fixes initial mode
setting on my Intel DN2800MT (Cedarview) board. Without it, mode
setting triggers an out-of-range error from the monitor for most modes,
but only on initial configuration (i.e. they can be configured
successfully from userspace after that).
Signed-off-by: Forest Bond <forest.bond@rapidrollout.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Was using the DCE41 code which was wrong. Fixes
blank displays on a number of Trinity systems.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
Against -net.
In the patch "netpoll: re-enable irq in poll_napi()", I tried to
fix the following warning:
[100718.051041] ------------[ cut here ]------------
[100718.051048] WARNING: at kernel/softirq.c:159 local_bh_enable_ip+0x7d/0xb0()
(Not tainted)
[100718.051049] Hardware name: ProLiant BL460c G7
...
[100718.051068] Call Trace:
[100718.051073] [<ffffffff8106b747>] ? warn_slowpath_common+0x87/0xc0
[100718.051075] [<ffffffff8106b79a>] ? warn_slowpath_null+0x1a/0x20
[100718.051077] [<ffffffff810747ed>] ? local_bh_enable_ip+0x7d/0xb0
[100718.051080] [<ffffffff8150041b>] ? _spin_unlock_bh+0x1b/0x20
[100718.051085] [<ffffffffa00ee974>] ? be_process_mcc+0x74/0x230 [be2net]
[100718.051088] [<ffffffffa00ea68c>] ? be_poll_tx_mcc+0x16c/0x290 [be2net]
[100718.051090] [<ffffffff8144fe76>] ? netpoll_poll_dev+0xd6/0x490
[100718.051095] [<ffffffffa01d24a5>] ? bond_poll_controller+0x75/0x80 [bonding]
[100718.051097] [<ffffffff8144fde5>] ? netpoll_poll_dev+0x45/0x490
[100718.051100] [<ffffffff81161b19>] ? ksize+0x19/0x80
[100718.051102] [<ffffffff81450437>] ? netpoll_send_skb_on_dev+0x157/0x240
by reenabling IRQ before calling ->poll, but it seems more
problems are introduced after that patch:
http://ozlabs.org/~akpm/stuff/IMG_20120824_122054.jpg
http://marc.info/?l=linux-netdev&m=134563282530588&w=2
So it is safe to fix be2net driver code directly.
This patch reverts the offending commit and fixes be_poll() by
avoid disabling BH there, this is okay because be_poll()
can be called either by poll_napi() which already disables
IRQ, or by net_rx_action() which already disables BH.
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Reported-by: Sylvain Munaut <s.munaut@whatever-company.com>
Cc: Sylvain Munaut <s.munaut@whatever-company.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: David Miller <davem@davemloft.net>
Cc: Sathya Perla <sathya.perla@emulex.com>
Cc: Subbu Seetharaman <subbu.seetharaman@emulex.com>
Cc: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: Cong Wang <amwang@redhat.com>
Tested-by: Sylvain Munaut <s.munaut@whatever-company.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
radeon_ring_restore is freeing the memory for the saved
ring data. We need to remember that, otherwise we try to
restore the ring data again on the next try. Additional
to that it shouldn't try the reset infinitely if we have
saved ring data.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
|
|
It seems some of those IGP dislike non dma32 page despite what
documentation says. Fix regression since we allowed non dma32
pages. It seems it only affect some revision of those IGP chips
as we don't know which one just force dma32 for all of them.
https://bugzilla.redhat.com/show_bug.cgi?id=785375
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Adjust the panel mode setup to match the behavior
of the vbios. Rather than checking for specific
bridge chip ids, just check the eDP configuration register.
This saves extra aux transactions and works across
DP bridge chips without requiring additional per chip
id checking.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Power gating is per crtc pair, but the powergating registers
should be called individually. The hw handles power up/down
properly. The pair is powered up if either crtc in the pair
is powered up and the pair is not powered down until both
crtcs in the pair are powered down. This simplifies
programming and should save additional power as the previous
code never actually power gated the crtc pair.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
The ordering is important and the current drm code
wasn't cutting it for modern DIG encoders. We need
to have information about crtc before setting up
the encoders so I've shifted the ordering a bit.
Probably we'll need a full rework akin to danvet's
recent intel patchs. This patch fixes numerous
issues with DP bridge chips and makes link training
much more reliable.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
Some plls are shared for DP.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
|
|
Checking of the second colorbuffer was skipped on r700, because
CB_TARGET_MASK was 0xf. With r600, CB_TARGET_MASK is changed to 0xff,
so we must set the number of samples of the second colorbuffer to 1 in order
to pass the CS checker.
The DRM version is bumped, because RESOLVE_BOX is always rejected without this
fix on r600.
Signed-off-by: Marek Olšák <maraeo@gmail.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This should help catch uninitialized registers and reject commands
because of that.
Signed-off-by: Marek Olšák <maraeo@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Signed-off-by: Marek Olšák <maraeo@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
delay.h header file was included twice.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
git://people.freedesktop.org/~danvet/drm-intel into drm-fixes
Daniel writes:
"Just a few smaller things:
- Fix up a pipe vs. plane confusion from a refactoring, fixes a regression
from 3.1 (Anhua Xu).
- Fix ivb sprite pixel formats (Vijay).
- Fixup ppgtt pde placement for machines where the Bios artifically limits
the availbale gtt space in the name of ... product differentiation
(Chris). This fixes an oops.
- Yet another no_lvds quirk entry."
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
i915: Quirk no_lvds on Gigabyte GA-D525TUD ITX motherboard
drm/i915: Use the correct size of the GTT for placing the per-process entries
drm/i915: fix color order for BGR formats on IVB
drm/i915: fix wrong order of parameters in port checking functions
|
|
git://anongit.freedesktop.org/git/nouveau/linux-2.6 into drm-fixes
Ben says its just a single fix to avoid the wrong pcopy units being used.
* 'drm-nouveau-fixes' of git://anongit.freedesktop.org/git/nouveau/linux-2.6:
drm/nvc0/copy: check PUNITS to determine which copy engines are disabled
|
|
On some Fermi chipsets (NVCE particularly) PCOPY1 doesn't exist. And if
what I've seen on Kepler is true of Fermi too, chipsets of the same type
can have different PCOPY units available.
This should fix a v3.5 regression reported by a number of people effecting
suspend/resume on NVC8/NVCE chipsets.
Cc: stable@vger.kernel.org [3.5]
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
Contiguous Memory Allocator requires each of its regions to be aligned
in such a way that it is possible to change migration type for all
pageblocks holding it and then isolate page of largest possible order from
the buddy allocator (which is MAX_ORDER-1). This patch relaxes alignment
requirements by one order, because MAX_ORDER alignment is not really
needed.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
CC: Michal Nazarewicz <mina86@mina86.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
|
|
For unimplemented ioctls the dasd driver should return -ENOTTY.
Reported-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Acked-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Fixes for AT91 related to:
- move to sparse IRQ: some drivers were forgotten
- a DTS typo
- the delay for removal of old at91_mci driver
* tag 'at91-fixes' of git://github.com/at91linux/linux-at91:
ARM: at91/feature-removal-schedule: delay at91_mci removal
ARM: at91/dts: remove partial parameter in at91sam9g25ek.dts
ARM: at91/clock: fix PLLA overclock warning
ARM: at91: fix rtc-at91sam9 irq issue due to sparse irq support
ARM: at91: fix system timer irq issue due to sparse irq support
|
|
This patch (as1603) adds a NOGET quirk for the Eaton Ellipse MAX UPS
device. (The USB IDs were already present in hid-ids.h, apparently
under a different name.)
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Laurent Bigonville <l.bigonville@edpnet.be>
CC: <stable@vger.kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull a hwmon fix from Guenter Roeck:
"Fix sensor readings for Asus M5A78L in asus_atk0110 driver."
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (asus_atk0110) Add quirk for Asus M5A78L
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc fixes from Arnd Bergmann:
"Bug fixes for various ARM platforms. About half of these are for OMAP
and submitted before but did not make it into v3.6-rc2."
* tag 'fixes-3.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (39 commits)
ARM: ux500: don't select LEDS_GPIO for snowball
ARM: imx: build i.MX6 functions only when needed
ARM: imx: select CPU_FREQ_TABLE when needed
ARM: imx: fix ksz9021rn_phy_fixup
ARM: imx: build pm-imx5 code only when PM is enabled
ARM: omap: allow building omap44xx without SMP
ARM: dts: imx51-babbage: fix esdhc cd/wp properties
ARM: imx6: spin the cpu until hardware takes it down
ARM: ux500: Ensure probing of Audio devices when Device Tree is enabled
ARM: ux500: Fix merge error, no matching driver name for 'snd_soc_u8500'
ARM i.MX6q: Add virtual 1/3.5 dividers in the LDB clock path
ARM: Kirkwood: fix Makefile.boot
ARM: Kirkwood: Fix iconnect leds
ARM: Orion: Set eth packet size csum offload limit
ARM: mv78xx0: fix win_cfg_base prototype
ARM: OMAP: dmtimers: Fix locking issue in omap_dm_timer_request*()
ARM: mmp: fix potential NULL dereference
ARM: OMAP4: Register the OPP table only for 4430 device
cpufreq: OMAP: Handle missing frequency table on SMP systems
ARM: OMAP4: sleep: Save the complete used register stack frame
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull three xen bug-fixes from Konrad Rzeszutek Wilk:
- Revert the kexec fix which caused on non-kexec shutdowns a race.
- Reuse existing P2M leafs - instead of requiring to allocate a large
area of bootup virtual address estate.
- Fix a one-off error when adding PFNs for balloon pages.
* tag 'stable/for-linus-3.6-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/setup: Fix one-off error when adding for-balloon PFNs to the P2M.
xen/p2m: Reuse existing P2M leafs if they are filled with 1:1 PFNs or INVALID.
Revert "xen PVonHVM: move shared_info to MMIO before kexec"
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
Pull powerpc fixes from Benjamin Herrenschmidt:
"I meant to sent that earlier but got swamped with other things, so
here are some powerpc fixes for 3.6. A few regression fixes and some
bug fixes that I deemed should still make it.
There's a FSL update from Kumar with a bunch of defconfig updates
along with a few embedded fixes.
I also reverted my g5_defconfig update that I merged earlier as it was
completely busted, not too sure what happened there, I'll do a new one
later."
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
Revert "powerpc: Update g5_defconfig"
powerpc/perf: Use pmc_overflow() to detect rolled back events
powerpc: Fix VMX in interrupt check in POWER7 copy loops
powerpc: POWER7 copy_to_user/copy_from_user patch applied twice
powerpc: Fix personality handling in ppc64_personality()
powerpc/dma-iommu: Fix IOMMU window check
powerpc: Remove unnecessary ifdefs
powerpc/kgdb: Restore current_thread_info properly
powerpc/kgdb: Bail out of KGDB when we've been triggered
powerpc/kgdb: Do not set kgdb_single_step on ppc
powerpc/mpic_msgr: Add missing includes
powerpc: Fix null pointer deref in perf hardware breakpoints
powerpc: Fixup whitespace in xmon
powerpc: Fix xmon dl command for new printk implementation
powerpc/fsl: fix "Failed to mount /dev: No such device" errors
powerpc/fsl: update defconfigs
booke/wdt: some ioctls do not return values properly
powerpc/p4080ds: dts - add usb controller version info and port0
powerpc/85xx: mpc85xx_defconfig - add VIA PATA support for MPC85xxCDS
powerpc/fsl-pci: Only scan PCI bus if configured as a host
|
|
Pull MIPS fixes from Ralf Baechle:
"Random fixes across the MIPS tree. The two hotspots are several bugs
in the module loader and the ath79 SOC support; also noteworthy is the
restructuring of the code to synchronize CPU timers across CPUs on
startup; the old code recently ceased to work due to unrelated
changes.
All except one of these patches have sat for a significant time in
linux-next for testing."
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: pci-ar724x: avoid data bus error due to a missing PCIe module
MIPS: Malta: Delete duplicate PCI fixup.
MIPS: ath79: don't hardcode the unavailability of the DSP ASE
MIPS: Synchronize MIPS count one CPU at a time
MIPS: BCM63xx: Fix SPI message control register handling for BCM6338/6348.
MIPS: Module: Deal with malformed HI16/LO16 relocation sequences.
MIPS: Fix race condition in module relocation code.
MIPS: Fix memory leak in error path of HI16/LO16 relocation handling.
MIPS: MTX-1: Add udelay to mtx1_pci_idsel
MIPS: ath79: select HAVE_CLK
MIPS: ath79: Use correct IRQ number for the OHCI controller on AR7240
MIPS: ath79: Fix number of GPIO lines for AR724[12]
MIPS: Octeon: Fix broken interrupt controller code.
|
|
Pull block-related fixes from Jens Axboe:
- Improvements to the buffered and direct write IO plugging from
Fengguang.
- Abstract out the mapping of a bio in a request, and use that to
provide a blk_bio_map_sg() helper. Useful for mapping just a bio
instead of a full request.
- Regression fix from Hugh, fixing up a patch that went into the
previous release cycle (and marked stable, too) attempting to prevent
a loop in __getblk_slow().
- Updates to discard requests, fixing up the sizing and how we align
them. Also a change to disallow merging of discard requests, since
that doesn't really work properly yet.
- A few drbd fixes.
- Documentation updates.
* 'for-linus' of git://git.kernel.dk/linux-block:
block: replace __getblk_slow misfix by grow_dev_page fix
drbd: Write all pages of the bitmap after an online resize
drbd: Finish requests that completed while IO was frozen
drbd: fix drbd wire compatibility for empty flushes
Documentation: update tunable options in block/cfq-iosched.txt
Documentation: update tunable options in block/cfq-iosched.txt
Documentation: update missing index files in block/00-INDEX
block: move down direct IO plugging
block: remove plugging at buffered write time
block: disable discard request merge temporarily
bio: Fix potential memory leak in bio_find_or_create_slab()
block: Don't use static to define "void *p" in show_partition_start()
block: Add blk_bio_map_sg() helper
block: Introduce __blk_segment_map_sg() helper
fs/block-dev.c:fix performance regression in O_DIRECT writes to md block devices
block: split discard into aligned requests
block: reorganize rounding of max_discard_sectors
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
Pull libata fixes from Jeff Garzik:
- libata-acpi regression fix
- additional or corrected drive quirks for ata_blacklist
- Kconfig text tweaking
- new PCI IDs
- pata_atiixp: quirk for MSI motherboard
- export ahci_dev_classify for an ahci_platform driver
* tag 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata: Add a space to " 2GB ATA Flash Disk" DMA blacklist entry
[libata] new quirk, lift bridge limits for Buffalo DriveStation Quattro
[libata] Kconfig: Elaborate that SFF is meant for legacy and PATA stuff
[libata] acpi: call ata_acpi_gtm during ata port init time
ata_piix: Add Device IDs for Intel Lynx Point-LP PCH
ahci: Add Device IDs for Intel Lynx Point-LP PCH
pata_atiixp: override cable detection on MSI E350DM-E33
ahci: un-staticize ahci_dev_classify
|
|
commit d70e551c8e1ecb6f20422f8db6bfe6a0049edcb8, Add " 2GB ATA Flash
Disk"/"ADMA428M" to DMA blacklist, should have added a space before 2GB.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Ben Hutchings says:
====================
Simple fix for a braino. Please also queue this for the 3.4 and 3.5
stable series.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Marc Kleine-Budde says:
====================
here are two fixes for the v3.6 release cycle. Alexey Khoroshilov submitted a
fix for a memory leak in the softing driver (in softing_load_fw()) in case a
krealloc() fails. Sven Schmitt fixed the misuse of the IRQF_SHARED flag in the
irq resouce of the sja1000 platform driver, now the correct flag is used. There
are no mainline users of this feature which need to be converted.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
John W. Linville says:
====================
This batch of fixes is intended for 3.6...
Johannes Berg gives us a pair of iwlwifi fixes. One corrects some
improperly defined ifdefs that lead to crashes and BUG_ONs. The other
prevents attempts to read SRAM for devices that aren't actually started.
Julia Lawall provides an ipw2100 fix to properly set the return code
from a function call before testing it! :-)
Thomas Huehn corrects the improper use of a constant related to a power
setting in ath5k.
Thomas Pedersen offers a mac80211 fix to properly handle destination
addresses of unicast frames passing though a mesh gate.
Vladimir Zapolskiy provides a brcmsmac fix to properly mark the
interface state when the device goes down.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds "#ifndef __<header>_H" for protecting header from double
inclusion.
Signed-off-by: Rayagond Kokatanur <rayagond@vayavyalabs.com>
Hacked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem
|
|
This board is incorrectly detected as having an LVDS connector,
resulting in the VGA output (the only available output on the board)
showing the console only in the top-left 1024x768 pixels, and an extra
LVDS connector appearing in X.
It's a desktop Mini-ITX board using an Atom D525 CPU with an NM10
chipset.
I've had this board for about a year, but this is the first time I
noticed the issue because I've been running it headless for most of its
life.
Signed-off-by: Calvin Walton <calvin.walton@kepstin.ca>
|
|
The current layout is to place the per-process tables at the end of the
GTT. However, this is currently using a hardcoded maximum size for the GTT
and not taking in account limitations imposed by the BIOS. Use the value
for the total number of entries allocated in the table as provided by
the configuration registers.
Reported-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Matthew Garret <mjg@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
The sja1000 platform driver wrongly assumes that a shared IRQ is indicated
with the IRQF_SHARED flag in irq resource flags. This patch changes the
driver to handle the correct flag IORESOURCE_IRQ_SHAREABLE instead.
There are no mainline users of the platform driver which wrongly make use
of IRQF_SHARED.
Signed-off-by: Sven Schmitt <sven.schmitt@volkswagen.de>
Acked-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Do not leak memory by updating pointer with potentially NULL realloc return value.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Pull crypto fixes from Herbert Xu:
"This push fixes a build error on 32-bit archs in the hifn driver as
well as a potential deadlock in the caam driver."
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: caam - fix possible deadlock condition
crypto: hifn_795x - fix 64bit division and undefined __divdi3 on 32bit archs
|
|
Pull IDE power management bugfix from David S. Miller.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/ide:
ide: fix generic_ide_suspend/resume Oops
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
Pull HID fix from Jiri Kosina:
"Fix for one particular device not being properly claimed by
hid-multitouch driver"
* 'upstream-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: Remove QUANTA from special drivers list
|
|
ETHTOOL_GRXCLSRULE returns filters for a TCP/IPv4 or UDP/IPv4 4-tuple
with source and destination swapped.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
Signed-off-by: Jakob Bornecrantz <jakob@vmware.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
If we try to print to the console device while its decoding is disabled,
the system will hang.
Reported-and-tested-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Olof Johansson <olof@lixom.net>
|
|
git://git.linaro.org/people/shawnguo/linux-2.6 into fixes
* 'imx/fixes-for-3.6' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: dts: imx51-babbage: fix esdhc cd/wp properties
ARM: imx6: spin the cpu until hardware takes it down
ARM i.MX6q: Add virtual 1/3.5 dividers in the LDB clock path
Also updates to Linux 3.6-rc2
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
