| Age | Commit message (Collapse) | Author |
|---|
|
Move a debug message from acpi_pci_sleep_wake() to
acpi_pm_device_sleep_wake() and use the standard dev_*() macros
in there.
Reviewed-by: Matthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Rework the PCI wake-up code so that it's easier to read without
changing the functionality.
Reviewed-by: Matthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
In general a BIOS may goof or we may hotplug in a hotplug controller.
In either case the kernel needs to reserve resources for plugging
in more devices in the future instead of creating a minimal resource
assignment.
We already do this for cardbus bridges I am just adding a variant
for pcie bridges.
v2: Make testing for pcie hotplug bridges based on a flag.
So far we only set the flag for pcie but a header_quirk
could easily be added for the non-standard pci hotplug
bridges.
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
There is a very old quirk for the intel E7502 E7320 and E7525 memory
controller hubs that disables usage of msi interrupts on pcie hotplug
bridges of those devices, and disables changing the affinity of irqs.
Today all we have to do to disable msi on a specific device is to set
dev->no_msi, which is much more straightforward than the previous
logic.
The re-running of this fixup after pci hotplug happens below these
devices is totally bogus. All of the state we change is pure software
state and we don't change the hardware at all. Which means hotplug on
the lower devices doesn't have a chance to change this state. So we
can safely remove the special case from the pciehp driver and the pcie
portdriver.
I suspect the special case was someone's expermental debug code that
slipped in. Certainly it isn't mentioned in commit
6fb8880a61510295aece04a542767161f624dffe aka BKrev:
41966101LJ_ogfOU0m2aE6teZfQnuQ where the code first appears.
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
This patch is required not to lost error records by action invoked on
error recovery, such as slot reset etc.
Following sample (real machine + dummy record injected by aer-inject)
shows that record of 28:00.1 could not be retrieved by recovery of 28:00.0:
- Before:
pcieport-driver 0000:00:02.0: AER: Multiple Uncorrected (Non-Fatal) error received: id=2801
e1000e 0000:28:00.0: PCIE Bus Error: severity=Uncorrected (Non-Fatal), type=Transaction Layer, id=2800(Receiver ID)
e1000e 0000:28:00.0: device [8086:1096] error status/mask=00001000/00100000
e1000e 0000:28:00.0: [12] Poisoned TLP (First)
e1000e 0000:28:00.0: TLP Header: 00000000 00000001 00000002 00000003
e1000e 0000:28:00.0: broadcast error_detected message
e1000e 0000:28:00.0: broadcast slot_reset message
e1000e 0000:28:00.0: setting latency timer to 64
e1000e 0000:28:00.0: restoring config space at offset 0x1 (was 0x100547, writing 0x100147)
e1000e 0000:28:00.0: PME# disabled
e1000e 0000:28:00.0: PME# disabled
e1000e 0000:28:00.1: setting latency timer to 64
e1000e 0000:28:00.1: restoring config space at offset 0x1 (was 0x100547, writing 0x100147)
e1000e 0000:28:00.1: PME# disabled
e1000e 0000:28:00.1: PME# disabled
e1000e 0000:28:00.0: broadcast resume message
e1000e 0000:28:00.0: AER driver successfully recovered
e1000e: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
- After:
pcieport-driver 0000:00:02.0: AER: Multiple Uncorrected (Non-Fatal) error received: id=2801
e1000e 0000:28:00.0: PCIE Bus Error: severity=Uncorrected (Non-Fatal), type=Transaction Layer, id=2800(Receiver ID)
e1000e 0000:28:00.0: device [8086:1096] error status/mask=00001000/00100000
e1000e 0000:28:00.0: [12] Poisoned TLP (First)
e1000e 0000:28:00.0: TLP Header: 00000000 00000001 00000002 00000003
e1000e 0000:28:00.1: PCIE Bus Error: severity=Uncorrected (Non-Fatal), type=Transaction Layer, id=2801(Receiver ID)
e1000e 0000:28:00.1: device [8086:1096] error status/mask=00081000/00100000
e1000e 0000:28:00.1: [12] Poisoned TLP (First)
e1000e 0000:28:00.1: [19] ECRC
e1000e 0000:28:00.1: TLP Header: 00000000 00000001 00000002 00000003
e1000e 0000:28:00.1: Error of this Agent(2801) is reported first
e1000e 0000:28:00.0: broadcast error_detected message
e1000e 0000:28:00.0: broadcast slot_reset message
e1000e 0000:28:00.0: setting latency timer to 64
e1000e 0000:28:00.0: restoring config space at offset 0x1 (was 0x100547, writing 0x100147)
e1000e 0000:28:00.0: PME# disabled
e1000e 0000:28:00.0: PME# disabled
e1000e 0000:28:00.1: setting latency timer to 64
e1000e 0000:28:00.1: restoring config space at offset 0x1 (was 0x100547, writing 0x100147)
e1000e 0000:28:00.1: PME# disabled
e1000e 0000:28:00.1: PME# disabled
e1000e 0000:28:00.0: broadcast resume message
e1000e 0000:28:00.0: AER driver successfully recovered
e1000e: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Use dev_printk like format.
Sample (real machine + dummy error injected by aer-inject):
- Before:
+------ PCI-Express Device Error ------+
Error Severity : Corrected
PCIE Bus Error type : Data Link Layer
Bad TLP :
Receiver ID : 2800
VendorID=8086h, DeviceID=1096h, Bus=28h, Device=00h, Function=00h
+------ PCI-Express Device Error ------+
Error Severity : Corrected
PCIE Bus Error type : Data Link Layer
Bad TLP :
Bad DLLP :
Receiver ID : 2801
VendorID=8086h, DeviceID=1096h, Bus=28h, Device=00h, Function=01h
Error of this Agent(2801) is reported first
- After:
pcieport-driver 0000:00:02.0: AER: Multiple Corrected error received: id=2801
e1000e 0000:28:00.0: PCIE Bus Error: severity=Corrected, type=Data Link Layer, id=2800(Receiver ID)
e1000e 0000:28:00.0: device [8086:1096] error status/mask=00000040/00000000
e1000e 0000:28:00.0: [ 6] Bad TLP
e1000e 0000:28:00.1: PCIE Bus Error: severity=Corrected, type=Data Link Layer, id=2801(Receiver ID)
e1000e 0000:28:00.1: device [8086:1096] error status/mask=000000c0/00000000
e1000e 0000:28:00.1: [ 6] Bad TLP
e1000e 0000:28:00.1: [ 7] Bad DLLP
e1000e 0000:28:00.1: Error of this Agent(2801) is reported first
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Compact struct and codes.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Cleanup.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Multiple bits might be set in the Uncorrectable Error Status
register. But aer_print_error_source() only report a error of
the lowest bit set in the error status register.
So print strings for all bits unmasked and set.
And check First Error Pointer to mark the error occured first.
This FEP is not valid when the corresponing bit of the Uncorrectable
Error Status register is not set, or unimplemented or undefined.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
ERR_{,UN}CORRECTABLE_ERROR_MASK are set of error bits which linux know,
set of PCI_ERR_COR_* and PCI_ERR_UNC_* defined in linux/pci_regs.h.
This masks make aerdrv not to report errors of unknown bit, while aerdrv
have ability to report such undefined errors as "Unknown Error Bit %2d".
OTOH aerdrv_errprint does not have any check of setting in mask register.
So it could report masked wrong error by finding bit in status without
knowing that the bit is masked in the mask register.
This patch changes aerdrv to use mask state in mask register propely
instead of defined/hardcoded ERR_{,UN}CORRECTABLE_ERROR_MASK.
This change prevents aerdrv from reporting masked error, and also enable
reporting unknown errors.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Reviewed-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
The static buffer errmsg_buff[] is used only for building error
message in fixed format, and is protected by a spinlock.
This patch removes this buffer and the spinlock.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Reviewed-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
The flag AER_MULTI_ERROR_VALID_FLAG in info->flag does mean that the
root port receives multiple error messages. Error messages can be
posted from different devices, so it does not mean that each reported
device has multiple errors.
If there are multiple error devices and the root port has valid error
source ID, it would be nice to report which device is the error source
reported first.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
In case of multiple errors, struct aer_err_info would be reused among
all reported devices. So the info->status should be initialized before
recycled. Otherwise error of one device might be reported as the error
of another device. Also info->flags has similar problem on reporting
TLP header.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Definitions of MASK macros in aerdrv_errprint.c are tricky and unsafe.
For example, AER_AGENT_TRANSMITTER_MASK(_sev, _stat) does work like:
static inline func(int _sev, int _stat)
{
if (_sev == AER_CORRECTABLE)
return (_stat & (PCI_ERR_COR_REP_ROLL|PCI_ERR_COR_REP_TIMER));
else
return (_stat & PCI_ERR_COR_REP_ROLL);
}
In case of else path here, for uncorrectable errors, testing bits in
_stat by PCI_ERR_COR_* does not make sense because _stat should have only
PCI_ERR_UNC_* bits originated in uncorrectable error status register.
But at this time this is safe because uncorrectable error using bit
position same to PCI_ERR_COR_REP_ROLL(= bit position 8) is not defined.
Likewise, AER_AGENT_COMPLETER_MASK is always PCI_ERR_UNC_COMP_ABORT but
it works because bit 15 of correctable error status is not defined.
It means that these MASK macros will turn to be wrong once if new error
is defined. (In fact, bit 15 of correctable is now defined in PCIe 2.1)
This patch changes these MASK macros to be more strict, not to return
PCI_ERR_COR_* bits for uncorrectable error status and vise versa.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Reviewed-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Add workaround macro to reduce the number of checkpatch warning:
WARNING: printk() should include KERN_ facility level
Before:
total: 0 errors, 10 warnings, 247 lines checked
After:
total: 0 errors, 1 warnings, 243 lines checked
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Before:
drivers/pci/pcie/aer/aer_inject.c
total: 4 errors, 4 warnings, 473 lines checked
drivers/pci/pcie/aer/aerdrv.c
total: 5 errors, 2 warnings, 333 lines checked
drivers/pci/pcie/aer/aerdrv.h
total: 1 errors, 0 warnings, 139 lines checked
drivers/pci/pcie/aer/aerdrv_core.c
total: 4 errors, 3 warnings, 872 lines checked
drivers/pci/pcie/aer/aerdrv_errprint.c
total: 12 errors, 11 warnings, 248 lines checked
After:
drivers/pci/pcie/aer/aer_inject.c
total: 0 errors, 0 warnings, 466 lines checked
drivers/pci/pcie/aer/aerdrv.c
total: 0 errors, 0 warnings, 335 lines checked
drivers/pci/pcie/aer/aerdrv.h
total: 0 errors, 0 warnings, 139 lines checked
drivers/pci/pcie/aer/aerdrv_core.c
total: 0 errors, 0 warnings, 869 lines checked
drivers/pci/pcie/aer/aerdrv_errprint.c
total: 0 errors, 10 warnings, 247 lines checked
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Reviewed-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Add ids module parameter which allows specifying initial IDs for the
pci-stub driver. When built into the kernel, pci-stub is linked
before any real pci drivers and by setting up IDs from initialization
it can prevent built-in drivers from attaching to specific devices.
While at it, make pci_stub_probe() print out about devices it grabbed
to weed out "but my controller isn't being probed" bug reports.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Separate out pci_add_dynid() from store_new_id() and export it so that
in-kernel code can add PCI IDs dynamically. As the function will be
available regardless of HOTPLUG, put it and pull pci_free_dynids()
outside of CONFIG_HOTPLUG.
This will be used by pci-stub to initialize initial IDs via module
param.
While at it, remove bogus get_driver() failure check.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Reviewed-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Add support for PCI-E 5.0 GT/s in max_bus_speed and cur_bus_speed.
Reviewed-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Fix typo in PCI-E link speed.
Reviewed-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
The L0s state can be managed separately for each direction (upstream
direction and downstream direction) of the link. But in the current
implementation, those are mixed up. With this patch, L0s for each
direction are managed separately.
To maintain three states (upstream direction L0s, downstream L0s and
L1), 'aspm_support', 'aspm_enabled', 'aspm_capable', 'aspm_disable'
and 'aspm_default' fields in struct pcie_link_state are changed to
3-bit from 2-bit. The 'latency' field is separated to two 'latency_up'
and 'latency_dw' fields to maintain exit latencies for each direction
of the link. For L0, 'latency_up.l0' and 'latency_dw.l0' are used to
configure upstream direction L0s and downstream direction L0s
respectively. For L1, larger value of 'latency_up.l1' and
'latency_dw.l1' is considered as L1 exit latency.
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
In the current implementation, ASPM L0s/L1 is disabled for all links
in the hierarchy if one of the link doesn't meet latency requirement.
But we can partially enable ASPM L0s/L1 on sub-tree in the hierarchy.
This patch allows partial L0s/L1 enablement in the hierarchy. And it
also reduce the calculation cost of ASPM configuration very much.
In the previous implementation, all links were enabled with the same
state. With this patch, enabled state for each link is determined
simply as follows (the 'requested' is from policy_to_aspm_state()).
enabled = requested & (link->aspm_capable & link->aspm_disable)
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Introduce 'aspm_capable' field to maintain the capable ASPM setting of
the link. By the 'aspm_capable', we don't need to recheck latency
every time ASPM policy is changed.
Each bit in 'aspm_capable' is associated to ASPM state (L0S/L1). The
bit is set if the associated ASPM state is supported by the link and
it satisfies the latency requirement (i.e. exit latency < endpoint
acceptable latency). The 'aspm_capable' is updated when
- an endpoint device is added (boot time or hot-plug time)
- an endpoint device is removed (hot-unplug time)
- PCI power state is changed.
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Introduce 'aspm_disable' flag to manage disabled ASPM state more
robust way.
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Fix possible NULL dereference in pcie_aspm_exit_link_state(). This
patch also cleanup some code.
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Remove the following check in __pcie_aspm_config_link() because it
nerver be true.
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
We must not clear bits in 'aspm_enabled' using 'aspm_support', or
'aspm_enabled' and 'aspm_default' might be different from the actual
state. In addtion, 'aspm_default' should be intialized even if
'aspm_support' is 0.
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
This patch adds the most recent additions to the list of 82576 device IDs
to the list of devices needing the SR-IOV quirk.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Fix some warnings reported in linux-next + also cleanup some
comment errors noticed by Pekka Paalanen.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Background:
Graphic devices are accessed through ranges in I/O or memory space. While most
modern devices allow relocation of such ranges, some "Legacy" VGA devices
implemented on PCI will typically have the same "hard-decoded" addresses as
they did on ISA. For more details see "PCI Bus Binding to IEEE Std 1275-1994
Standard for Boot (Initialization Configuration) Firmware Revision 2.1"
Section 7, Legacy Devices.
The Resource Access Control (RAC) module inside the X server currently does
the task of arbitration when more than one legacy device co-exists on the same
machine. But the problem happens when these devices are trying to be accessed
by different userspace clients (e.g. two server in parallel). Their address
assignments conflict. Therefore an arbitration scheme _outside_ of the X
server is needed to control the sharing of these resources. This document
introduces the operation of the VGA arbiter implemented for Linux kernel.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Tiago Vignatti <tiago.vignatti@nokia.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Cleanups (nearly based on checkpatch).
Before: total: 11 errors, 2 warnings, 0 checks, 842 lines checked
After: total: 0 errors, 0 warnings, 0 checks, 842 lines checked
v2: fix it's/its mistakes in comment
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Cleanup based on the prototype from Matthew Milcox.
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Cleanup based on the prototype from Matthew Milcox.
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Cleanup based on the prototype from Matthew Milcox.
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Move it from the middle of the function to the end.
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Unify msi_free_irqs() and msix_free_all_irqs(), and rename it to a
common void function free_msi_irqs().
And relocate the common function to where the prototype is located now.
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
use list_first_entry() instead of list_entry().
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
The msi_list never have MSI-X's msi_desc while MSI is enabled,
and also it never have MSI's msi_desc while MSI-X is enabled.
This patch remove check for MSI-X entry from the pci_disable_msi(),
referring that pci_disable_msix() does not have any check for MSI
entry.
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
We already print it out for pci bridges, so also print it out for pci devices.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
http://bugzilla.kernel.org/show_bug.cgi?id=12542 reports that with the
quirk not applied on resume, msi stops working after resuming and mcp78s
ahci fails due to IRQ mis-delivery. Apply it on resume too.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Peer Chen <pchen@nvidia.com>
Cc: Tj <linux@tjworld.net>
Reported-by: Nicolas Derive <kalon33@ubuntu.com>
Cc: Greg KH <greg@kroah.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Shut off the long standing
linux/drivers/pci/search.c:144: warning: 'pci_find_device' is deprecated (declared at linux/drivers/pci/search.c:136)
linux/drivers/pci/search.c:144: warning: 'pci_find_device' is deprecated (declared at linux/drivers/pci/search.c:136)
warnings that appear on every build when CONFIG_PCI_LEGACY is enabled.
gcc warns for the use in EXPORT_SYMBOL
I moved these to a separate file and disabled the warning in the Makefile for that file.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
One more form factor for Compaq Evo D510, which needs the same quirk
as the other form factors. Apparently there's no hardware monitoring
chip on that one, but SPD EEPROMs, so it's still worth unhiding the
SMBus.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Nuzhna Pomoshch <nuzhna_pomoshch@yahoo.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Some devices allow an individual function to be reset without affecting
other functions in the same device: that's what pci_reset_function does.
For devices that have this support, expose reset attribite in sysfs.
This is useful e.g. for virtualization, where a qemu userspace
process wants to reset the device when the guest is reset,
to emulate machine reboot as closely as possible.
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
We cannot simply call acpi_get_pci_dev() on any random ACPI handle
and hope that it works, because a PCI root bridge may not have
an associated struct pci_dev.
This is allowed per the PCI specification, and is referred to as a
non-materialized bridge.
So, depending on the type of PCI bridge that the handle points to,
use the appropriate interface to return the struct pci_bus correctly.
Reviewed-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
We can simplify ACPI drivers if we can tell whether a handle is an
ACPI PCI root or not.
Reviewed-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
yenta needs this for example.
Acked-by: Matthew Wilcox <willy@linux.intel.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Instead of open-coding pci_find_parent_resource and request_resource,
just call pci_claim_resource.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
This was #define'd as 0 on all platforms, so let's get rid of it.
This change makes pci_scan_slot() slightly easier to read.
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Tony Luck <tony.luck@intel.com>
Cc: David Howells <dhowells@redhat.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Acked-by: Russell King <linux@arm.linux.org.uk>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Kyle McMartin <kyle@mcmartin.ca>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Andy Whitcroft reported an oops in aoe triggered by use of an
incorrectly initialised request_queue object:
[ 2645.959090] kobject '<NULL>' (ffff880059ca22c0): tried to add
an uninitialized object, something is seriously wrong.
[ 2645.959104] Pid: 6, comm: events/0 Not tainted 2.6.31-5-generic #24-Ubuntu
[ 2645.959107] Call Trace:
[ 2645.959139] [<ffffffff8126ca2f>] kobject_add+0x5f/0x70
[ 2645.959151] [<ffffffff8125b4ab>] blk_register_queue+0x8b/0xf0
[ 2645.959155] [<ffffffff8126043f>] add_disk+0x8f/0x160
[ 2645.959161] [<ffffffffa01673c4>] aoeblk_gdalloc+0x164/0x1c0 [aoe]
The request queue of an aoe device is not used but can be allocated in
code that does not sleep.
Bruno bisected this regression down to
cd43e26f071524647e660706b784ebcbefbd2e44
block: Expose stacked device queues in sysfs
"This seems to generate /sys/block/$device/queue and its contents for
everyone who is using queues, not just for those queues that have a
non-NULL queue->request_fn."
Addresses http://bugs.launchpad.net/bugs/410198
Addresses http://bugzilla.kernel.org/show_bug.cgi?id=13942
Note that embedding a queue inside another object has always been
an illegal construct, since the queues are reference counted and
must persist until the last reference is dropped. So aoe was
always buggy in this respect (Jens).
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Cc: Andy Whitcroft <apw@canonical.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Bruno Premont <bonbons@linux-vserver.org>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
Reinette Chatre reports a frozen system (with blinking keyboard LEDs)
when switching from graphics mode to the text console, or when
suspending (which does the same thing). With netconsole, the oops
turned out to be
BUG: unable to handle kernel NULL pointer dereference at 0000000000000084
IP: [<ffffffffa03ecaab>] i915_driver_irq_handler+0x26b/0xd20 [i915]
and it's due to the i915_gem.c code doing drm_irq_uninstall() after
having done i915_gem_idle(). And the i915_gem_idle() path will do
i915_gem_idle() ->
i915_gem_cleanup_ringbuffer() ->
i915_gem_cleanup_hws() ->
dev_priv->hw_status_page = NULL;
but if an i915 interrupt comes in after this stage, it may want to
access that hw_status_page, and gets the above NULL pointer dereference.
And since the NULL pointer dereference happens from within an interrupt,
and with the screen still in graphics mode, the common end result is
simply a silently hung machine.
Fix it by simply uninstalling the irq handler before idling rather than
after. Fixes
http://bugzilla.kernel.org/show_bug.cgi?id=13819
Reported-and-tested-by: Reinette Chatre <reinette.chatre@intel.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
