Age | Commit message (Collapse) | Author |
|
This driver enable the max3110 device, it can be used as
a system console. the IRQ needs be enabled if user want a
better performance. MRST max3110 works in 3.684MHz clock,
which supports 230400 as its maximum rate.
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Adding UART_CAP_EFR and UART_CAP_SLEEP flags will enable sleep mode
and automatic CTS flow control for 16C950 UARTs. It will also avoid
capabilities detection warning like this:
"ttyS0: detected caps 00000700 should be 00000100"
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Signed-off-by: Andy Shevchenko <ext-andriy.shevchenko@nokia.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
as there's no config CONSOLE (never has been as far as I can tell) and
noone has ever missed that piece of code, it should be safe to remove
it making the kernel a tiny bit less complex.
Signed-off-by: Christoph Egger <siccegge@cs.fau.de>
Acked-by: Greg Ungerer <gerg@snapgear.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
drivers/char/n_gsm.c: linux/timer.h is included more than once.
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
* git://git.infradead.org/mtd-2.6: (79 commits)
mtd: Remove obsolete <mtd/compatmac.h> include
mtd: Update copyright notices
jffs2: Update copyright notices
mtd-physmap: add support users can assign the probe type in board files
mtd: remove redwood map driver
mxc_nand: Add v3 (i.MX51) Support
mxc_nand: support 8bit ecc
mxc_nand: fix correct_data function
mxc_nand: add V1_V2 namespace to registers
mxc_nand: factor out a check_int function
mxc_nand: make some internally used functions overwriteable
mxc_nand: rework get_dev_status
mxc_nand: remove 0xe00 offset from registers
mtd: denali: Add multi connected NAND support
mtd: denali: Remove set_ecc_config function
mtd: denali: Remove unuseful code in get_xx_nand_para functions
mtd: denali: Remove device_info_tag structure
mtd: m25p80: add support for the Winbond W25Q32 SPI flash chip
mtd: m25p80: add support for the Intel/Numonyx {16,32,64}0S33B SPI flash chips
mtd: m25p80: add support for the EON EN25P{32, 64} SPI flash chips
...
Fix up trivial conflicts in drivers/mtd/maps/{Kconfig,redwood.c} due to
redwood driver removal.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6: (96 commits)
no need for list_for_each_entry_safe()/resetting with superblock list
Fix sget() race with failing mount
vfs: don't hold s_umount over close_bdev_exclusive() call
sysv: do not mark superblock dirty on remount
sysv: do not mark superblock dirty on mount
btrfs: remove junk sb_dirt change
BFS: clean up the superblock usage
AFFS: wait for sb synchronization when needed
AFFS: clean up dirty flag usage
cifs: truncate fallout
mbcache: fix shrinker function return value
mbcache: Remove unused features
add f_flags to struct statfs(64)
pass a struct path to vfs_statfs
update VFS documentation for method changes.
All filesystems that need invalidate_inode_buffers() are doing that explicitly
convert remaining ->clear_inode() to ->evict_inode()
Make ->drop_inode() just return whether inode needs to be dropped
fs/inode.c:clear_inode() is gone
fs/inode.c:evict() doesn't care about delete vs. non-delete paths now
...
Fix up trivial conflicts in fs/nilfs2/super.c
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (59 commits)
igbvf.txt: Add igbvf Documentation
igb.txt: Add igb documentation
e100/e1000*/igb*/ixgb*: Add missing read memory barrier
ixgbe: fix build error with FCOE_CONFIG without DCB_CONFIG
netxen: protect tx timeout recovery by rtnl lock
isdn: gigaset: use after free
isdn: gigaset: add missing unlock
solos-pci: Fix race condition in tasklet RX handling
pkt_sched: Fix sch_sfq vs tcf_bind_filter oops
net: disable preemption before call smp_processor_id()
tcp: no md5sig option size check bug
iwlwifi: fix locking assertions
iwlwifi: fix TX tracer
isdn: fix information leak
net: Fix napi_gro_frags vs netpoll path
usbnet: remove noisy and hardly useful printk
rtl8180: avoid potential NULL deref in rtl8180_beacon_work
ath9k: Remove myself from the MAINTAINERS list
libertas: scan before assocation if no BSSID was given
libertas: fix association with some APs by using extended rates
...
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/ide-2.6:
tx493xide: use min_t() macro instead of min()
drivers/ide: Use memdup_user
via82cxxx: fix typo for VT6415 PCIE PATA IDE Host Controller support.
ide-cd: Do not access completed requests in the irq handler
|
|
* 'rs485fix' of git://www.jni.nu/cris:
CRIS: ioctl for getting RS485 information
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: fix build with make 3.82
Revert "Input: appletouch - fix integer overflow issue"
memblock: Fix memblock_is_region_reserved() to return a boolean
powerpc: Trim defconfigs
powerpc: fix i8042 module build error
sound/soc: mpc5200_psc_ac97: Use gpio pins for cold reset
powerpc/5200: add mpc5200_psc_ac97_gpio_reset
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx: (30 commits)
DMAENGINE: at_hdmac: locking fixlet
DMAENGINE: pch_dma: kill another usage of __raw_{read|write}l
dma: dmatest: fix potential sign bug
ioat2: catch and recover from broken vtd configurations v6
DMAENGINE: add runtime slave control to COH 901 318 v3
DMAENGINE: add runtime slave config to DMA40 v3
DMAENGINE: generic slave channel control v3
dmaengine: Driver for Topcliff PCH DMA controller
intel_mid: Add Mrst & Mfld DMA Drivers
drivers/dma: Eliminate a NULL pointer dereference
dma/timb_dma: compile warning on 32 bit
DMAENGINE: ste_dma40: support older silicon
DMAENGINE: ste_dma40: support disabling physical channels
DMAENGINE: ste_dma40: no disabled phy channels on ux500
DMAENGINE: ste_dma40: fix suspend bug
DMAENGINE: ste_dma40: add DB8500 memcpy channels
DMAENGINE: ste_dma40: no flow control on memcpy
DMAENGINE: ste_dma40: arch updates for LCLA and LCPA
DMAENGINE: ste_dma40: allocate LCLA dynamically
DMAENGINE: ste_dma40: no premature stop
...
Fix up trivial conflicts in arch/arm/mach-ux500/devices-db8500.c
|
|
According include/linux/console_struct.h,vc_scr_end is unsigned long.
struct vc_data {
unsigned short vc_num; /* Console number */
unsigned int vc_cols; /* [#] Console size */
unsigned int vc_rows;
unsigned int vc_size_row; /* Bytes per row */
unsigned int vc_scan_lines; /* # of scan lines */
unsigned long vc_origin; /* [!] Start of real screen */
unsigned long vc_scr_end; /* [!] End of real screen */
unsigned long vc_visible_origin; /* [!] Top of visible window */
unsigned int vc_top, vc_bottom; /* Scrolling region */
const struct consw *vc_sw;
unsigned short *vc_screenbuf;
...
}
Signed-off-by: qiaochong <qiaochong@loongson.cn>
Cc: Greg KH <greg@kroah.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
kernel will die on some platform when switch from vga mode to framebuffer
mode. The reason of this bug is that bind_con_driver reset vc->vc_origin
to (unsigned long)vc->vc_screenbuf.
On vgacon vc->vc_origin is not releated to vc->vc_screenbuf,if set
vc->vc_origin to vc->vc_screenbuf,kernel will die on vc_do_resize.
static int vc_do_resize(struct tty_struct *tty, struct tty_struct *real_tty,
struct vc_data *vc, unsigned int cols, unsigned int lines)
{
unsigned long old_origin, new_origin, new_scr_end, rlth, rrem, err = 0;
unsigned int old_cols, old_rows, old_row_size, old_screen_size;
unsigned int new_cols, new_rows, new_row_size, new_screen_size;
unsigned int end, user;
...
end = (old_rows > new_rows) ? old_origin +
(old_row_size * new_rows) :
vc->vc_scr_end;
...
/*
here for a test from vgacon to framebuffer:
old_origin=0x810814a0,end=0xb00b8fa0,vc->vc_origin=0x810814a0
the code bellow will copy memory from 0x810814a0 to 0xb00b8fa0,
this will cover kernel code,kernel died here.
*/
while (old_origin < end) {
scr_memcpyw((unsigned short *) new_origin,
(unsigned short *) old_origin, rlth);
if (rrem)
scr_memsetw((void *)(new_origin + rlth),
vc->vc_video_erase_char, rrem);
old_origin += old_row_size;
new_origin += new_row_size;
}
...
}
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: qiaochong <qiaochong@loongson.cn>
Cc: Greg KH <greg@kroah.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Allow device probing to recognise the Fintek F71808E.
Sysfs interface:
* Fan/pwm control is the same as for F71889FG
* Temperature and voltage sensor handling is largely the same as for
the F71889FG
- Has one temperature sensor less (doesn't have temp3)
- Misses one voltage sensor (doesn't have V6, thus in6_input refers to
what in7_input refers for F71889FG)
For the purpose of the sysfs interface fxxxx_in_temp_attr[] is split up
such that it can largely be reused.
Signed-off-by: Giel van Schijndel <me@mortis.eu>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
register_hotcpu_notifier() is designed to make these ifdefs unnecessary.
Cc: Chen Gong <gong.chen@linux.intel.com>
Cc: Rudolf Marek <r.marek@assembler.cz>
Cc: Huaxu Wan <huaxu.wan@intel.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Update coretemp supported CPU TjMax lists and some cleanup work.
Signed-off-by: Chen Gong <gong.chen@linux.intel.com>
Cc: Rudolf Marek <r.marek@assembler.cz>
Cc: Huaxu Wan <huaxu.wan@intel.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
If one coretemp device can't be added, it should allow subsequent adding
operation because every new-added device will create a new sysfs group,
not an additional sensor sys entry.
Signed-off-by: Chen Gong <gong.chen@linux.intel.com>
Cc: Rudolf Marek <r.marek@assembler.cz>
Cc: Huaxu Wan <huaxu.wan@intel.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fix two errors in hotplug. One is for hotplug notifier. The other is
unnecessary driver unregister. Because even none of online cpus supports
coretemp, we can't assume new onlined cpu doesn't support it either. If
related driver is unregistered there we have no chance to use coretemp
from then on.
Signed-off-by: Chen Gong <gong.chen@linux.intel.com>
Cc: Rudolf Marek <r.marek@assembler.cz>
Cc: Huaxu Wan <huaxu.wan@intel.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This driver adds support for the monitoring features of the Summit
Microelectronics SMM665 Six-Channel Active DC Output Controller/Monitor.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This driver will report the heading values in degrees to the sysfs
interface. The values returned are headings . e.g. 245.6
Alan: Cleanups requested now all folded in and a sysfs description to keep
Andrew happy. The sysfs description now resembles hwmon.
Signed-off-by: Kalhan Trisal <kalhan.trisal@intel.com>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add Lenovo Thinkpad T400. I have done the testing on my laptop. The
hdaps module detects the device and the hdapsd daemon is able to [un]park
the disk.
Signed-off-by: Ritesh Raj Sarraf <rrs@debian.org>
Cc: Frank Seidel <frank@f-seidel.de>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The error may happen at any iteration of the for loop, this patch properly
unregisters already registed edd_devices in error path.
[akpm@linux-foundation.org: remove unneeded NULL test]
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The previous change added WARN_ON() in misc_deregister(). So it is not
necessary to WARN_ON() misc_deregister() failure by callers.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
misc_deregister() returns an error only when it attempts to unregister
the device that is not registered. This is the driver's bug.
Most of the drivers don't check the return value of misc_deregister().
(It is not bad thing because most of kernel *_unregister() API always
succeed and do not return value)
So it is better to indicate the error by WARN_ON() in misc_deregister().
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This driver adds support for the BMP085 digital pressure sensor from Bosch
Sensortec. It exposes a sysfs api to userspace where pressure and
temperature measurement results can be read from the pressure0_input and
temp0_input file. The chip is able to calculate the average of up to
eight samples to increase the accuracy. This feature can be controlled by
writing to the oversampling file.
The BMP085 digital pressure sensor can measure ambient air pressure and
temperature. Both values can be obtained from sysfs files. The pressure
is measured by reading from pressure0_input. Valid values range from
30000 to 110000 pascal with a resolution of 1 pascal (=0.01 millibar).
temp0_input holds the current temperature in degree celsius, multiplied by
10. This results in a resolution of a tenth degree celsius. Values range
from -400 to 850.
To increase the accuracy, this chip can calculate the average of 1, 2, 4
or 8 samples. This behavior is controlled through the oversampling sysfs
file. Two to the power of the value written to that file specifies how
many samples will be used. Valid values: 0..3.
[akpm@linux-foundation.org: fix typo]
[shubhrajyoti@ti.com: optimize the wait time for the pressure sensor, definition of long is arch dependent so make it u32]
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Christoph Mair <christoph.mair@gmail.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Cc: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fix i386 PAE compile warning:
drivers/misc/hpilo.c: In function `ilo_ccb_setup':
drivers/misc/hpilo.c:274: warning: cast to pointer from integer of different size
dma_addr_t is 64 on i386 PAE which causes a size mismatch.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Acked-by: David Altobelli <david.altobelli@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add support for ROHM BH1780GLI Ambient light sensor.
BH1780 supports I2C interface. Driver supports read/update of power state
and read of lux value (through SYSFS). Writing value 3 to power_state
enables the sensor and current lux value could be read.
Currently this driver follows the same sysfs convention as supported by
drivers/misc/isl29003.c.
Signed-off-by: Hemanth V <hemanthv@ti.com>
Reviewed-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
On some SoC chips, HW resources may be in use during any particular idle
period. As a consequence, the cpuidle states that the SoC is safe to
enter can change from idle period to idle period. In addition, the
latency and threshold of each cpuidle state can vary, depending on the
operating condition when the CPU becomes idle, e.g. the current cpu
frequency, the current state of the HW blocks, etc.
cpuidle core and the menu governor, in the current form, are geared
towards cpuidle states that are static, i.e. the availabiltiy of the
states, their latencies, their thresholds are non-changing during run
time. cpuidle does not provide any hook that cpuidle drivers can use to
adjust those values on the fly for the current idle period before the menu
governor selects the target cpuidle state.
This patch extends cpuidle core and the menu governor to handle states
that are dynamic. There are three additions in the patch and the patch
maintains backwards-compatibility with existing cpuidle drivers.
1) add prepare() to struct cpuidle_device. A cpuidle driver can hook
into the callback and cpuidle will call prepare() before calling the
governor's select function. The callback gives the cpuidle driver a
chance to update the dynamic information of the cpuidle states for the
current idle period, e.g. state availability, latencies, thresholds,
power values, etc.
2) add CPUIDLE_FLAG_IGNORE as one of the state flags. In the prepare()
function, a cpuidle driver can set/clear the flag to indicate to the
menu governor whether a cpuidle state should be ignored, i.e. not
available, during the current idle period.
3) add power_specified bit to struct cpuidle_device. The menu governor
currently assumes that the cpuidle states are arranged in the order of
increasing latency, threshold, and power savings. This is true or can
be made true for static states. Once the state parameters are dynamic,
the latencies, thresholds, and power savings for the cpuidle states can
increase or decrease by different amounts from idle period to idle
period. So the assumption of increasing latency, threshold, and power
savings from Cn to C(n+1) can no longer be guaranteed.
It can be straightforward to calculate the power consumption of each
available state and to specify it in power_usage for the idle period.
Using the power_usage fields, the menu governor then selects the state
that has the lowest power consumption and that still satisfies all other
critieria. The power_specified bit defaults to 0. For existing cpuidle
drivers, cpuidle detects that power_specified is 0 and fills in a dummy
set of power_usage values.
Signed-off-by: Ai Li <aili@codeaurora.org>
Cc: Len Brown <len.brown@intel.com>
Acked-by: Arjan van de Ven <arjan@linux.intel.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Venkatesh Pallipadi <venki@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
drivers/base/node.c: In function 'node_read_meminfo':
drivers/base/node.c:139: warning: the frame size of 848 bytes is
larger than 512 bytes
Fix it by splitting the sprintf() into three parts. It has no functional
change.
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fix a build failure "error: void value not ignored as it ought to be"
by removing an assignment of a void return value. The functionality of
the code is not changed.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Acked-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
After the commit that changed ipmi_si detecting sequence from SMBIOS/ACPI
to ACPI/SMBIOS,
| commit 754d453185275951d39792865927ec494fa1ebd8
| Author: Matthew Garrett <mjg@redhat.com>
| Date: Wed May 26 14:43:47 2010 -0700
|
| ipmi: change device discovery order
|
| The ipmi spec provides an ordering for si discovery. Change the driver to
| match, with the exception of preferring smbios to SPMI as HPs (at least)
| contain accurate information in the former but not the latter.
ipmi_si can not be initialized.
[ 138.799739] calling init_ipmi_devintf+0x0/0x109 @ 1
[ 138.805050] ipmi device interface
[ 138.818131] initcall init_ipmi_devintf+0x0/0x109 returned 0 after 12797 usecs
[ 138.822998] calling init_ipmi_si+0x0/0xa90 @ 1
[ 138.840276] IPMI System Interface driver.
[ 138.846137] ipmi_si: probing via ACPI
[ 138.849225] ipmi_si 00:09: [io 0x0ca2] regsize 1 spacing 1 irq 0
[ 138.864438] ipmi_si: Adding ACPI-specified kcs state machine
[ 138.870893] ipmi_si: probing via SMBIOS
[ 138.880945] ipmi_si: Adding SMBIOS-specified kcs state machineipmi_si: duplicate interface
[ 138.896511] ipmi_si: probing via SPMI
[ 138.899861] ipmi_si: Adding SPMI-specified kcs state machineipmi_si: duplicate interface
[ 138.917095] ipmi_si: Trying ACPI-specified kcs state machine at i/o address 0xca2, slave address 0x0, irq 0
[ 138.928658] ipmi_si: Interface detection failed
[ 138.953411] initcall init_ipmi_si+0x0/0xa90 returned 0 after 110847 usecs
in smbios has
DMI/SMBIOS
Handle 0x00C5, DMI type 38, 18 bytes
IPMI Device Information
Interface Type: KCS (Keyboard Control Style)
Specification Version: 2.0
I2C Slave Address: 0x00
NV Storage Device: Not Present
Base Address: 0x0000000000000CA2 (I/O)
Register Spacing: 32-bit Boundaries
in DSDT has
Device (BMC)
{
Name (_HID, EisaId ("IPI0001"))
Method (_STA, 0, NotSerialized)
{
If (LEqual (OSN, Zero))
{
Return (Zero)
}
Return (0x0F)
}
Name (_STR, Unicode ("IPMI_KCS"))
Name (_UID, Zero)
Name (_CRS, ResourceTemplate ()
{
IO (Decode16,
0x0CA2, // Range Minimum
0x0CA2, // Range Maximum
0x00, // Alignment
0x01, // Length
)
IO (Decode16,
0x0CA6, // Range Minimum
0x0CA6, // Range Maximum
0x00, // Alignment
0x01, // Length
)
})
Method (_IFT, 0, NotSerialized)
{
Return (One)
}
Method (_SRV, 0, NotSerialized)
{
Return (0x0200)
}
}
so the reg spacing should be 4 instead of 1.
Try to calculate regspacing for this kind of system.
Observed on a Sun Fire X4800. Other OSes work and pass certification.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-by: Matthew Garrett <mjg@redhat.com>
Cc: Len Brown <len.brown@intel.com>
Cc: Myron Stowe <myron.stowe@hp.com>
Cc: Corey Minyard <minyard@acm.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
drm: fix fallouts from slow-work -> wq conversion
workqueue: workqueue_cpu_callback() should be cpu_notifier instead of hotcpu_notifier
workqueue: add missing __percpu markup in kernel/workqueue.c
|
|
... and let iput_final() do the actual eviction or retention
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Replace inode_setattr with opencoded variants of it in all callers. This
moves the remaining call to vmtruncate into the filesystem methods where it
can be replaced with the proper truncate sequence.
In a few cases it was obvious that we would never end up calling vmtruncate
so it was left out in the opencoded variant:
spufs: explicitly checks for ATTR_SIZE earlier
btrfs,hugetlbfs,logfs,dlmfs: explicitly clears ATTR_SIZE earlier
ufs: contains an opencoded simple_seattr + truncate that sets the filesize just above
In addition to that ncpfs called inode_setattr with handcrafted iattrs,
which allowed to trim down the opencoded variant.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Add ioctl to CRIS serial driver to get RS485 data from user-space.
Signed-off-by: Claudio Scordino <claudio@evidence.eu.com>
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
|
|
Commit 991ea75c (drm: use workqueue instead of slow-work), which made
drm to use wq instead of slow-work, didn't account for the return
value difference between delayed_slow_work_enqueue() and
queue_delayed_work(). The former returns 0 on success and -errno on
failures while the latter never fails and only uses the return value
to indicate whether the work was already pending or not.
This misconversion triggered spurious error messages. Remove the now
unnecessary return value check and error message.
Markus: caught another incorrect conversion in drm_kms_helper_poll_enable()
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Tested-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Cc: David Airlie <airlied@linux.ie>
Cc: dri-devel@lists.freedesktop.org
|
|
This fixes a warning ("comparison of distinct pointer types lacks a
cast") introduced by the commit
040f6b4f14adb2ca5babb84e9fb2ebc6661e0be2 ("tx493xide: use ->pio_mode
value to determine pair device speed").
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use memdup_user when user data is immediately copied into the
allocated region.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression from,to,size,flag;
position p;
identifier l1,l2;
@@
- to = \(kmalloc@p\|kzalloc@p\)(size,flag);
+ to = memdup_user(from,size);
if (
- to==NULL
+ IS_ERR(to)
|| ...) {
<+... when != goto l1;
- -ENOMEM
+ PTR_ERR(to)
...+>
}
- if (copy_from_user(to, from, size) != 0) {
- <+... when != goto l2;
- -EFAULT
- ...+>
- }
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Without this fix, init of the via82cxxx driver causes a oops with a
stack resembling the one below, and the boot blocks between init of
USB devices and launch of init (was easy to bisect by booting with
init=/bin/sh).
Pid: 279, comm: work_for_cpu Not tainted 2.6.34.1-00003-ga42ea77 #2
Call Trace:
[<ffffffff81045691>] ? warn_slowpath_common+0x76/0x8c
[<ffffffff810456f9>] ? warn_slowpath_fmt+0x40/0x45
[<ffffffff812eb5a1>] ? printk+0x40/0x47
[<ffffffff8108e1fd>] ? enable_irq+0x3e/0x64
[<ffffffffa0003900>] ? ide_probe_port+0x55c/0x589 [ide_core]
[<ffffffffa0003f22>] ? ide_host_register+0x273/0x628 [ide_core]
[<ffffffffa00083e3>] ? ide_pci_init_two+0x4da/0x5c5 [ide_core]
[<ffffffff8106117e>] ? up+0xe/0x36
[<ffffffff81045d7e>] ? release_console_sem+0x17e/0x1ae
[<ffffffff812d945b>] ? klist_iter_exit+0x14/0x1e
[<ffffffff8120ed23>] ? bus_find_device+0x75/0x83
[<ffffffffa0022832>] ? via_init_one+0x269/0x28a [via82cxxx]
[<ffffffffa00223a2>] ? init_chipset_via82cxxx+0x0/0x1ea [via82cxxx]
[<ffffffff81059f25>] ? do_work_for_cpu+0x0/0x1b
[<ffffffff81190c65>] ? local_pci_probe+0x12/0x16
[<ffffffff81059f30>] ? do_work_for_cpu+0xb/0x1b
[<ffffffff8105d0dd>] ? kthread+0x75/0x7d
[<ffffffff810097e4>] ? kernel_thread_helper+0x4/0x10
[<ffffffff8105d068>] ? kthread+0x0/0x7d
[<ffffffff810097e0>] ? kernel_thread_helper+0x0/0x10
---[ end trace 89c8cb70379b5bda ]---
The typo was introduced in a354ae8747d0687093ce244e76b15b6174d2f098,
and affects 2.6.33-rc4 and later.
Signed-off-by: Yann Dirson <ydirson@altern.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ide_cd_error_cmd() can complete an erroneous request with leftover
buffers. Signal this with its return value so that the request is not
accessed after its completion in the irq handler and we oops.
Cc: <stable@kernel.org> # 32.x 33.x 34.x
Signed-off-by: Borislav Petkov <bp@alien8.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 04b4b88cca0ebe3813b4b6f014fb6a0db380b137.
While the original problem only caused a slight disturbance on the
edge of the touchpad, the commit above to "fix" it completely breaks
operation on some other models such as mine.
We'll sort this out separately, revert the patch for now.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Based on patches from Sonny Rao and Milton Miller...
Combined the patches to fix up clean_tx_irq and clean_rx_irq.
The PowerPC architecture does not require loads to independent bytes
to be ordered without adding an explicit barrier.
In ixgbe_clean_rx_irq we load the status bit then load the packet data.
With packet split disabled if these loads go out of order we get a
stale packet, but we will notice the bad sequence numbers and drop it.
The problem occurs with packet split enabled where the TCP/IP header
and data are in different descriptors. If the reads go out of order
we may have data that doesn't match the TCP/IP header. Since we use
hardware checksumming this bad data is never verified and it makes it
all the way to the application.
This bug was found during stress testing and adding this barrier has
been shown to fix it. The bug can manifest as a data integrity issue
(bad payload data) or as a BUG in skb_pull().
This was a nasty bug to hunt down, if people agree with the fix I think
it's a candidate for stable.
Previously Submitted to e1000-devel only for ixgbe
http://marc.info/?l=e1000-devel&m=126593062701537&w=3
We've now seen this problem hit with other device drivers (e1000e mostly)
So I'm resubmitting with fixes for other Intel Device Drivers with
similar issues.
CC: Milton Miller <miltonm@bga.com>
CC: Anton Blanchard <anton@samba.org>
CC: Sonny Rao <sonnyrao@us.ibm.com>
CC: stable <stable@kernel.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Building ixgbe without DCB_CONFIG and FCOE_CONFIG will cause
a build error. This resolves the build error by wrapping
the fcoe.up in CONFIG_IXGBE_DCB ifdefs.
Also frames were being priority VLAN tagged even without DCB
enabled. This fixes this so that 8021Q priority tags are
only added with DCB actually enabled.
Reported-by: divya <dipraksh@linux.vnet.ibm.com>
Reported-by: Jon Mason <jon.mason@exar.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
arch/tile: check kmalloc() result
arch/tile: catch up on various minor cleanups.
arch/tile: avoid erroneous error return for PTRACE_POKEUSR.
tile: set ARCH_KMALLOC_MINALIGN
tile: remove homegrown L1_CACHE_ALIGN macro
arch/tile: Miscellaneous cleanup changes.
arch/tile: Split the icache flush code off to a generic <arch> header.
arch/tile: Fix bug in support for atomic64_xx() ops.
arch/tile: Shrink the tile-opcode files considerably.
arch/tile: Add driver to enable access to the user dynamic network.
arch/tile: Enable more sophisticated IRQ model for 32-bit chips.
Move list types from <linux/list.h> to <linux/types.h>.
Add wait4() back to the set of <asm-generic/unistd.h> syscalls.
Revert adding some arch-specific signal syscalls to <linux/syscalls.h>.
arch/tile: Do not use GFP_KERNEL for dma_alloc_coherent(). Feedback from fujita.tomonori@lab.ntt.co.jp.
arch/tile: core support for Tilera 32-bit chips.
Fix up the "generic" unistd.h ABI to be more useful.
|
|
* 'for-linus' of git://github.com/schandinat/linux-2.6:
drivers/video/via/via-gpio.c: fix warning
viafb: Depends on X86
fbdev: section cleanup in viafb driver
viafb: fix accel_flags check_var bug
viafb: probe cleanups
viafb: remove ioctls which break the framebuffer interface
viafb: update fix before calculating depth
viafb: PLL value cleanup
viafb: simplify lcd size "detection"
viafb: fix PCI table
viafb: add lcd scaling support for some IGPs
viafb: improve lcd code readability
viafb: remove duplicated scaling code
MAINTAINERS: update viafb entry
|
|
* 'for-linus' of git://gitorious.org/linux-omap-dss2/linux: (64 commits)
OMAP: DSS2: OMAPFB: add support for FBIO_WAITFORVSYNC
OMAP: DSS2: Replace strncmp() with sysfs_streq() in overlay_manager_store()
OMAP: DSS2: Fix error path in omap_dsi_update()
OMAP: DSS2: TDO35S: fix video signaling
OMAP: DSS2: OMAPFB: Fix invalid bpp for PAL and NTSC modes
OMAP: DSS2: OMAPFB: Fix probe error path
OMAP3EVM: Replace vdvi regulator supply with vdds_dsi
OMAP: DSS2: Remove extra return statement
OMAP: DSS2: adjust YUV overlay width to be even
OMAP: DSS2: OMAPFB: Fix sysfs mirror input check
OMAP: DSS2: OMAPFB: Remove redundant color register range check
OMAP: DSS2: OMAPFB: Remove redundant rotate range check
OMAP: DSS2: OMAPFB: Check fb2display() return value
OMAP: DSS2: Taal: Optimize enable_te, rotate, mirror when value unchanged
OMAP: DSS2: DSI: detect unsupported update requests
OMAP: DSS2: DSI: increase FIFO low threshold
OMAP: DSS2: DSI: Add error IRQ mask for DSI complexIO
OMAP: DSS2: DSI: Remove BTA after set_max_rx_packet_size
OMAP: DSS2: change manual update scaling setup
OMAP: DSS2: DSI: use BTA to end the frame transfer
...
|