summaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2010-05-19ixgbe: add support for active DA cablesDon Skidmore
This patch adds support of active DA cables. This is renaming and adding some PHY type enumerations. Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-19ixgbe: dcb, do not tag tc_prio_control framesJohn Fastabend
The network stack indicate packets should not be DCB tagged by setting the priority to TC_PRIO_CONTROL. One usage for this is lldp frames which are not suppossed to be tagged. Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-19ixgbe: fix ixgbe_tx_is_paused logicJohn Fastabend
The TFCS bits show the current XON state. Meaning that the device is paused if these bits are 0. This fixes the logic to work as it was intended. Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-19ixgbe: always enable vlan strip/insert when DCB is enabledYi Zou
when DCB mode is on, we want the HW VLAN stripping to be always enabled. Signed-off-by: Yi Zou <yi.zou@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-19ixgbe: remove some redundant code in setting FCoE FIP filterYi Zou
The ETQS setup for FIP out side the if..else is enough for the ETQS setup for FIP, so remove redundant code. Signed-off-by: Yi Zou <yi.zou@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-19ixgbe: fix wrong offset to fc_frame_header in ixgbe_fcoe_ddpYi Zou
Make sure we point to the right offset of the fc_frame_header when VLAN header exists and HW has VLAN stripping disabled. Signed-off-by: Yi Zou <yi.zou@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-19ixgbe: fix header len when unsplit packet overflows to data bufferShannon Nelson
When in packet split mode, packet type is not recognized, and the packet is larger than the header size, the 82599 overflows the packet into the data area, but doesn't set the HDR_LEN field. We can safely assume the length is the current header size. This fixes an obscure corner case that can be triggered by non-ip packet headers or (more likely) by disabling the L2 packet recognition. Signed-off-by: Shannon Nelson <shannon.nelson@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-18cxgb4: notify upper drivers if the device is already up when they loadDimitris Michailidis
Upper layer drivers aren't notified that a device is ready if their modules load after the device becomes ready. Add the missing notification. Signed-off-by: Dimitris Michailidis <dm@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-18cxgb4: keep interrupts available when the ports are brought downDimitris Michailidis
The PF driver needs to remain alert while its ports are down to service requests or errors from virtual functions or FW so keep interrupts and queues available when the ports are brought down. The change makes open_device_map unnecessary so remove it. Signed-off-by: Dimitris Michailidis <dm@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-18cxgb4: fix initial addition of MAC addressDimitris Michailidis
The call to add the MAC address during link initialization wasn't adding the address to one of the HW tables. Fix. Signed-off-by: Dimitris Michailidis <dm@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-18cnic: Return SPQ credit to bnx2x after ring setup and shutdown.Michael Chan
Everytime the iSCSI ring finishes setup or shutdown, we need to return the SPQ (slow path queue) credit to the bnx2x driver. Without this step, the SPQ will eventually be full causing iSCSI to fail. This can happen after 3 or 4 MTU changes for example. Add code to wait for these slow path commands to complete in the RX ring and return the SPQ credit to bnx2x. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-18cnic: Convert cnic_local_flags to atomic ops.Michael Chan
It is easier to expand the flags for other purposes because it does not require a spin_lock. The next bug fix patch needs a flag in cnic_local_flags. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-18can: Fix SJA1000 command register writes on SMP systemsOliver Hartkopp
The SJA1000 command register is concurrently written in the rx-path to free the receive buffer _and_ in the tx-path to start the transmission. The SJA1000 data sheet, 6.4.4 COMMAND REGISTER (CMR) states: "Between two commands at least one internal clock cycle is needed in order to proceed. The internal clock is half of the external oscillator frequency." On SMP systems the current implementation leads to a write stall in the tx-path, which can be solved by adding some general locking and some time to settle the write_reg() operation for the command register. Thanks to Klaus Hitschler for the original fix and detailed problem description. This patch applies on net-2.6 and (with some offsets) on net-next-2.6 . Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> Acked-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-18ARCNET: Limit com20020 PCI ID matches for SOHARD cardsAndreas Bombe
The SH SOHARD ARCNET cards are implemented using generic PLX Technology PCI<->IOBus bridges. Subvendor and subdevice IDs were not specified, causing the driver to attach to any such bridge and likely crash the system by attempting to initialize an unrelated device. Fix by specifying subvendor and subdevice according to the values found in the PCI-ID Repository at http://pci-ids.ucw.cz/ . Cc: stable@kernel.org Signed-off-by: Andreas Bombe <aeb@debian.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-18cleanup: remove pppoe_ioctl() declaration.Rami Rosen
Hi, - This patch removes pppoe_ioctl() declaration in drivers/net/pppoe.c as it is unneeded. Regards, Rami Rosen Signed-off-by: Rami Rosen <ramirose@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-18drivers/net: Use kcalloc or kzallocJulia Lawall
Use kcalloc or kzalloc rather than the combination of kmalloc and memset. The semantic patch that makes this change is as follows: (http://coccinelle.lip6.fr/) // <smpl> @@ expression x,y,flags; statement S; type T; @@ x = - kmalloc + kcalloc ( - y * sizeof(T), + y, sizeof(T), flags); if (x == NULL) S -memset(x, 0, y * sizeof(T)); @@ expression x,size,flags; statement S; @@ -x = kmalloc(size,flags); +x = kzalloc(size,flags); if (x == NULL) S -memset(x, 0, size); // </smpl> Signed-off-by: Julia Lawall <julia@diku.dk> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-18drivers/net/vmxnet3: Use kzallocJulia Lawall
Use kzalloc rather than the combination of kmalloc and memset. The semantic patch that makes this change is as follows: (http://coccinelle.lip6.fr/) // <smpl> @@ expression x,size,flags; statement S; @@ -x = kmalloc(size,flags); +x = kzalloc(size,flags); if (x == NULL) S -memset(x, 0, size); // </smpl> Signed-off-by: Julia Lawall <julia@diku.dk> Signed-off-by: Bhavesh Davda <bhavesh@vmware.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-18drivers/net: Use kzallocJulia Lawall
Use kzalloc rather than the combination of kmalloc and memset. The semantic patch that makes this change is as follows: (http://coccinelle.lip6.fr/) // <smpl> @@ expression x,size,flags; statement S; @@ -x = kmalloc(size,flags); +x = kzalloc(size,flags); if (x == NULL) S -memset(x, 0, size); // </smpl> Signed-off-by: Julia Lawall <julia@diku.dk> Acked-by: Lennert Buytenhek <buytenh@wantstofly.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-18net: Add ndo_{set|get}_vf_port support for enic dynamic vnicsScott Feldman
Add enic ndo_{set|get}_vf_port ops to support setting/getting port-profile for enic dynamic devices. Enic dynamic devices are just like normal enic eth devices except dynamic enics require an extra configuration step to assign a port-profile identifier to the interface before the interface is useable. Once a port-profile is assigned, link comes up on the interface and is ready for I/O. The port-profile is used to configure the network port assigned to the interface. The network port configuration includes VLAN membership, QoS policies, and port security settings typical of a data center network. A dynamic enic initially has a zero-mac address. Before a port-profile is assigned, a valid non-zero unicast mac address should be assign to the dynamic enic interface. Signed-off-by: Scott Feldman <scofeldm@cisco.com> Signed-off-by: Roopa Prabhu <roprabhu@cisco.com>
2010-05-18drivers/net: remove useless semicolonsJoe Perches
switch and while statements don't need semicolons at end of statement [ Fixup minor conflicts with recent wimax merge... -DaveM ] Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-18qeth: support the new OSA CHPID types OSX and OSMUrsula Braun
The qeth driver is enabled to support the new OSA CHPID types OSX and OSM. Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com> Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-18drivers/s390/net: Drop memory allocation castJulia Lawall
Drop cast on the result of kmalloc and similar functions. The semantic patch that makes this change is as follows: (http://coccinelle.lip6.fr/) // <smpl> @@ type T; @@ - (T *) (\(kmalloc\|kzalloc\|kcalloc\|kmem_cache_alloc\|kmem_cache_zalloc\| kmem_cache_alloc_node\|kmalloc_node\|kzalloc_node\)(...)) // </smpl> Signed-off-by: Julia Lawall <julia@diku.dk> Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-18pegasus: fix USB device ID for ETX-US2Tadashi Abe
USB device ID definition for I-O Data ETX-US2 is wrong. Correct ID is 0x093a. Here's snippet from /proc/bus/usb/devices; T: Bus=01 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 2 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=ff(vend.) Sub=ff Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=04bb ProdID=093a Rev= 1.01 S: Manufacturer=I-O DATA DEVICE,INC. S: Product=I-O DATA ETX2-US2 S: SerialNumber=A26427 C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=224mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=00 Driver=pegasus E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=83(I) Atr=03(Int.) MxPS= 8 Ivl=125us This patch enables pegasus driver to work fine with ETX-US2. Signed-off-by: Tadashi Abe <tabe@mvista.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-18can: sja1000 platform data fixesWolfgang Grandegger
The member "clock" of struct "sja1000_platform_data" is documented as "CAN bus oscillator frequency in Hz" but it's actually used as the CAN clock frequency, which is half of it. To avoid further confusion, this patch fixes it by renaming the member to "osc_freq". That way, also non mainline users will notice the change. The platform code for the relevant boards is updated accordingly. Furthermore, pre-defined values are now used for the members "ocr" and "cdr". Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-18Merge branch 'for-davem' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6
2010-05-18dm9000: fix "BUG: spinlock recursion"Baruch Siach
dm9000_set_rx_csum and dm9000_hash_table are called from atomic context (in dm9000_init_dm9000), and from non-atomic context (via ethtool_ops and net_device_ops respectively). This causes a spinlock recursion BUG. Fix this by renaming these functions to *_unlocked for the atomic context, and make the original functions locking wrappers for use in the non-atomic context. Signed-off-by: Baruch Siach <baruch@tkos.co.il> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-18drivers/net/usb: Use kmemdupJulia Lawall
Use kmemdup when some other buffer is immediately copied into the allocated region. A simplified version of the semantic patch that makes this change is as follows: (http://coccinelle.lip6.fr/) // <smpl> @@ expression from,to,size,flag; statement S; @@ - to = \(kmalloc\|kzalloc\)(size,flag); + to = kmemdup(from,size,flag); if (to==NULL || ...) S - memcpy(to, from, size); // </smpl> Signed-off-by: Julia Lawall <julia@diku.dk> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-18drivers/net/usb: Use kmemdupJulia Lawall
Use kmemdup when some other buffer is immediately copied into the allocated region. A simplified version of the semantic patch that makes this change is as follows: (http://coccinelle.lip6.fr/) // <smpl> @@ expression from,to,size,flag; statement S; @@ - to = \(kmalloc\|kzalloc\)(size,flag); + to = kmemdup(from,size,flag); if (to==NULL || ...) S - memcpy(to, from, size); // </smpl> Signed-off-by: Julia Lawall <julia@diku.dk> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-18drivers/net/usb: Use kmemdupJulia Lawall
Use kmemdup when some other buffer is immediately copied into the allocated region. A simplified version of the semantic patch that makes this change is as follows: (http://coccinelle.lip6.fr/) // <smpl> @@ expression from,to,size,flag; statement S; @@ - to = \(kmalloc\|kzalloc\)(size,flag); + to = kmemdup(from,size,flag); if (to==NULL || ...) S - memcpy(to, from, size); // </smpl> Signed-off-by: Julia Lawall <julia@diku.dk> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-18fsl_pq_mdio: Fix mdiobus allocation handlingAnton Vorontsov
The driver could return success code even if mdiobus_alloc() failed. This patch fixes the issue. Signed-off-by: Anton Vorontsov <avorontsov@mvista.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-18atm: select FW_LOADER in Kconfig for solos-pciNathan Williams
solos-pci uses request_firmware() for firmware upgrades Signed-off-by: Nathan Williams <nathan@traverse.com.au> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-18r6040: fix link checking with switchesFlorian Fainelli
The current link checking logic only works for one port, which is not correct for swiches were multiple ports can have different link status. As a result we would only check for link status on port 1 of the switch. Move the calls to mii_check_media in r6040_timer which will be polling a single PHY chip correctly and assume link is up for switches. Signed-off-by: Florian Fainelli <florian@openwrt.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-18gianfar: Remove legacy PM callbacksAnton Vorontsov
These callbacks were needed because dev_pm_ops support for OF platform devices was in the powerpc tree, and the patch that added dev_pm_ops for gianfar driver was in the netdev tree. Now that netdev and powerpc trees have merged into Linus' tree, we can remove the legacy hooks. Signed-off-by: Anton Vorontsov <avorontsov@mvista.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-18bnx2x: avoid TX timeout when stopping deviceStanislaw Gruszka
When stop device call netif_carrier_off() just after disabling TX queue to avoid possibility of netdev watchdog warning and ->ndo_tx_timeout() invocation. Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-18bnx2: Use netif_carrier_off() to prevent timeout.Michael Chan
Based on original patch from Stanislaw Gruszka <sgruszka@redhat.com>. Using netif_carrier_off() is better than updating all the ->trans_start on all the tx queues. netif_carrier_off() needs to be called after bnx2_disable_int_sync() to guarantee no race conditions with the serdes timers that can modify the carrier state. If the chip or phy is reset, carrier will turn back on when we get the link interrupt. If there is no reset, we need to turn carrier back on in bnx2_netif_start(). Again, the phy_lock prevents race conditions with the serdes timers. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-18bnx2: Update 5709 MIPS firmware and version to 2.0.15.Michael Chan
New firmware fixes a performance regression on small packets. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-18bnx2: Fix register printouts during NETEV_WATCHDOG.Eddie Wai
Dump the correct MCP registers and add EMAC_RX_STATUS register during NETDEV_WATCHDOG for debugging. Signed-off-by: Eddie Wai <waie@broadcom.com> Signed-off-by: Benjamin Li <benli@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-18qlcnic: mark device state failAmit Kumar Salecha
Device state need to be mark as FAILED, if fail to start firmware. Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-18qlcnic: remove unused registerAmit Kumar Salecha
Removing register defines which are not used by Qlgoic CNA device. Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-18qlcnic: fix internal loopback testSucheta Chakraborty
Reset/set DEV_UP bit during allocation and deallocation of resources. Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com> Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-18qlcnic: module param for firmware load optionAmit Kumar Salecha
By default fw is loaded from flash, user can change this priority using load_fw_file module param. Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-18qlcnic: fix rx bytes statisticsSucheta Chakraborty
Added lrobytes to it. Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com> Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-18qlcnic: change adapter name displaySucheta Chakraborty
Append mac address to adapter name. Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com> Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-18qlcnic: fix memory leaksAnirban Chakraborty
Fixes memory leak in error path when memory allocation for adapter data structures fails. Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com> Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-18netdev: bfin_mac: check for mii_bus platform dataSonic Zhang
If the platform data for the mii_bus is missing, gracefully error out rather than deference NULL pointers. Signed-off-by: Sonic Zhang <sonic.zhang@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-18netdev: bfin_mac: handle timeouts with the MDIO registers gracefullyMike Frysinger
Have the low level MDIO functions pass back up timeout information so we don't waste time polling them multiple times when there is a problem, and so we don't let higher layers think the device is available when it isn't. Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-18netdev: bfin_mac: use promiscuous flag for promiscuous modeSonic Zhang
Rather than using the Receive All Frames (RAF) bit to enable promiscuous mode, use the Promiscuous (PR) bit. This lowers overhead at runtime as we let the hardware process the packets that should actually be checked. Signed-off-by: Sonic Zhang <sonic.zhang@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-18netdev: bfin_mac: add support for wake-on-lan magic packetsMichael Hennerich
Note that WOL works only in PM Suspend Standby Mode (Sleep Mode). Signed-off-by: Michael Hennerich <michael.hennerich@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-18netdev: bfin_mac: clear RXCKS if hardware generated checksum is not enabledSonic Zhang
Otherwise we might be get a setting mismatch from a previous module or bootloader and what the driver currently expects. Signed-off-by: Sonic Zhang <sonic.zhang@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-18netdev: bfin_mac: deduce Ethernet FCS from hardware IP payload checksumSonic Zhang
IP checksum is based on 16-bit one's complement algorithm, so to deduce a value from checksum is equal to add its complement. Unfortunately, the Blackfin on-chip MAC checksum logic only works when the IP packet has a header length of 20 bytes. This is true for most IPv4 packets, but not for IPv6 packets or IPv4 packets which use header options. So only use the hardware checksum when appropriate. Signed-off-by: Sonic Zhang <sonic.zhang@analog.com> Signed-off-by: Jon Kowal <jon.kowal@dspecialists.de> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v0.10.2 at 2024-08-05 05:54:11 (GMT)