| Age | Commit message (Collapse) | Author |
|---|
|
The GPIO register caching is the result of wrong assumptions and incomplete
knowledge about the GPIO registers and their functionality.
Today, we know that it is not needed.
It is also limited to a single register and therefore incomplete (newer chips
are using multiple registers).
Instead of extending the caching, get rid of it, because it has no real
benefits and just bloats/complicates the code.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
em28xx-input.c to em28xx.h
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
descriptions
- add definition for GPIO register 0x09 (reading/input)
- extend the information the chip variants that support GPIO registers 0x08/0x09
- rename EM28XX_R08_GPIO to EM2820_R08_GPIO_CTRL
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
em276x/7x/8x, em2874/174/84
The em25xx/em276x/7x/8x provides 4 GPIO register sets,
each of them consisting of separate read and a write registers.
The same registers are also used by the em2874/174/84.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Remove the silly redefines of pr_err/info/debug.
This improves readability and it also gets rid of a bunch of warnings when
compiling this driver for older kernels using the compatibility media_build
system.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The r820t_imr() calibration function of the Rafael Micro R820T tuner
generates this error at every tune attempt:
r820t 0-001a: No valid PLL values for 2252021 kHz!
The function was inspired by the original Realtek driver for rtl2832 devices
with the r820t tuner; anyway, in the original code the XTAL frequency of
the tuner was expressed in KHz, while in the kernel driver it is expressed
in Hz; so the calibration failed because of an out-of-range initial value.
The final result of the computation is then passed to the r820t_set_mux()
and r820t_set_pll() functions, but the conversion from KHz to Hz is already
correctly implemented.
Signed-off-by: Gianluca Gennari <gennarone@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The memcpy in shadow_store() could exceed buffer limits when r > 0.
Signed-off-by: Gianluca Gennari <gennarone@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
fe->tuner_priv and fe->ops.tuner_ops are initialized twice in r820t_attach().
Remove the redundant initializations and also move fe->ops.tuner_ops
initialization outside of the mutex lock (as in the xc4000 tuner code for example).
Signed-off-by: Gianluca Gennari <gennarone@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Remove all links of the subdev's media entity after internal_ops
'unregistered' call and right before unregistering the entity from
a media device.
It is assumed here that an unregistered (orphan) media entity cannot
have links to other entities registered to a media device.
It is also assumed the media links should be created/removed with
the media graph's mutex held.
The above implies that the caller of v4l2_device_unregister_subdev()
must not hold the graph's mutex.
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This function allows to remove all media entity's links to other
entities, leaving no references to a media entity's links array
at its remote entities.
Currently, when a driver of some entity is removed it will free its
media entities links[] array, leaving dangling pointers at other
entities that are part of same media graph. This is troublesome when
drivers of a media device entities are in separate kernel modules,
removing only some modules will leave others in an incorrect state.
This function is intended to be used when an entity is being
unregistered from a media device.
With an assumption that normally the media links should be created
between media entities registered to a media device, with the graph
mutex held.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
media_entity_cleanup() frees the links array which will be accessed by
media_entity_remove_links() called by v4l2_device_unregister_subdev().
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
media_entity_cleanup() frees the links array which will be accessed by
media_entity_remove_links() called by v4l2_device_unregister_subdev().
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
"Series of fixes for 3.10. There are some usual driver fixes (mostly
on s5p/exynos playform drivers), plus some fixes at V4L2 core"
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (40 commits)
[media] soc_camera: error dev remove and v4l2 call
[media] sh_veu: fix the buffer size calculation
[media] sh_veu: keep power supply until the m2m context is released
[media] sh_veu: invoke v4l2_m2m_job_finish() even if a job has been aborted
[media] v4l2-ioctl: don't print the clips list
[media] v4l2-ctrls: V4L2_CTRL_CLASS_FM_RX controls are also valid radio controls
[media] cx88: fix NULL pointer dereference
[media] DocBook/media/v4l: update version number
[media] exynos4-is: Remove "sysreg" clock handling
[media] exynos4-is: Fix reported colorspace at FIMC-IS-ISP subdev
[media] exynos4-is: Ensure fimc-is clocks are not enabled until properly configured
[media] exynos4-is: Prevent NULL pointer dereference when firmware isn't loaded
[media] s5p-mfc: Add NULL check for allocated buffer
[media] s5p-mfc: added missing end-of-lines in debug messages
[media] s5p-mfc: v4l2 controls setup routine moved to initialization code
[media] s5p-mfc: separate encoder parameters for h264 and mpeg4
[media] s5p-mfc: Remove special clock usage in driver
[media] s5p-mfc: Remove unused s5p_mfc_get_decoded_status_v6() function
[media] v4l2: mem2mem: save irq flags correctly
[media] coda: v4l2-compliance fix: add VIDIOC_CREATE_BUFS support
...
|
|
Pull clock framework fixes from Mike Turquette:
"Half of the fixes here are for Exynos5, fixing regressions in CPUfreq
due to the common clock framework conversion as well as one fix which
allows the platform to properly reboot again.
One core framework fix patches up a memory leak, another fixes a build
error for the SPEAr platform and finally a Tegra-specific fix allows
PCIe to initialize properly on that platform again"
* tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mturquette/linux:
ARM: tegra30: clocks: Fix pciex clock registration
clk: exynos5250: Add CLK_IGNORE_UNUSED flag for pmu clock
clk: spear: fix build error for spear3xx
clk: samsung: Fix pll36xx_recalc_rate to handle kdiv properly
clk: exynos5250: Add sclk_mpll to the parent list of mout_cpu clock
clk: exynos5250: Update cpufreq related clocks for EXYNOS5250
clk: remove notifier from list before freeing it
|
|
Error handling of usb_submit_urb() is not as all others in imon_probe().
It just unlocks mutexes and returns nonzero leaving all already
allocated resources unfreed.
The patch makes sure all the resources are deallocated.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
use module_pci_driver instead of init/exit, make code clean
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
use module_pci_driver instead of init/exit, make code clean.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
use module_pci_driver instead of init/exit, make code clean.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
use module_pci_driver instead of init/exit, make code clean.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
use module_pci_driver instead of init/exit, make code clean.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
use module_pci_driver instead of init/exit, make code clean.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
As USB/PCI/MEDIA_SUPPORT dependencies can be tristate, we can't
simply make the bool menu to be dependent on it. Everything below
the menu should also depend on it, otherwise, we risk to allow
building them with 'y', while only 'm' would be supported.
So, add an IF just before everything below, in order to avoid
such risks.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The sensor is powered by three supplies. Use the bulk regulator API to
enable and disable them instead of performing the operations manually.
This fixes a warning caused by ignoring the return value of
regulator_enable().
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Add OF support for the mt9p031 sensor driver.
Alongside this patch sorts the header inclusion alphabetically.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
drivers/media/i2c/ths8200.c: In function ‘ths8200_g_register’:
drivers/media/i2c/ths8200.c:121:21: warning: unused variable ‘client’ [-Wunused-variable]
drivers/media/i2c/ths8200.c: In function ‘ths8200_s_register’:
drivers/media/i2c/ths8200.c:132:21: warning: unused variable ‘client’ [-Wunused-variable]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Prabhakar Lad <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Fix uninitialized fields and a missing TRY_FMT implementation in saa6752hs.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
- map overlay format values to the supported ranges
- set colorspace
- zero priv field
- fix cliplist handling
- fix field handling
- initialize ovbuf values
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This is a global field, not a per-filehandle field.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
These fields are global, not per-filehandle.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This is global data, not per-filehandle data.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This information is already available in vfl_type in video_device.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This cleans up the saa712x setup code and there are no functional changes.
Signed-off-by: Ismael Luceno <ismael.luceno@corp.bluecherry.net>
[hans.verkuil@cisco.com: add clarification that this is cleanup only]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The full datasheets are available from TI website:-
http://www.ti.com/product/ths8200
Note: This patch adds support only for progressive format
as of now.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mats Randgaard <mats.randgaard@cisco.com>
Signed-off-by: Martin Bugge <martin.bugge@cisco.com>
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
- do exact matching for special formats like PAL-M
- drop autodetect support: it's non-standard, and it is bogus as well since there
is no way to get back the detected standard since neither g_std nor querystd are
implemented.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Improve the querystd comment.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Currently, if the norm set is V4L2_STD_ALL, then autodetect the current
standard and use that. This is non-standard behavior, and in fact it hasn't
worked for a very long time: before s_std is called in this driver, the
v4l2 core will mask it with the tvnorms field. So even if the application
passes V4L2_STD_ALL, the zoran driver will always see a subset of that.
Since nobody ever complained about this we just remove this non-standard
functionality.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
AND the standard mask with the detected standards.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Return V4L2_STD_UNKNOWN if no signal is detected.
Otherwise AND the standard mask with the detected standards.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Return V4L2_STD_UNKNOWN if no signal is detected.
Otherwise AND the standard mask with the detected standards.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Return V4L2_STD_UNKNOWN if no signal is detected.
Otherwise AND the standard mask with the detected standards.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Return V4L2_STD_UNKNOWN if no signal is detected.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Return V4L2_STD_UNKNOWN if no signal is detected.
Otherwise AND the standard mask with the detected standards.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Return V4L2_STD_UNKNOWN if no signal is detected.
Otherwise AND the standard mask with the detected standards.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Return V4L2_STD_UNKNOWN if no signal is detected.
Otherwise AND the standard mask with the detected standards.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
If no signal is detected, return V4L2_STD_UNKNOWN. Otherwise AND the standard
with the detected standards.
Note that the v4l2 core initializes the std with tvnorms before calling the
querystd ioctl.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Scott Jiang <scott.jiang.linux@gmail.com>
Acked-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The use of current_norm to keep track of the current standard has been
deprecated for quite some time. Now that all drivers that were using it
have been converted to use g_std we can drop it from the core.
It was a bad idea to introduce this at the time: since it is a per-device
node field it didn't work for drivers that create multiple nodes, all sharing
the same tuner (e.g. video and vbi nodes, or a raw video node and a compressed
video node). In addition it was very surprising behavior that g_std was
implemented in the core. Often drivers implemented both g_std and current_norm,
because they didn't understand how it should be used.
Since the benefits were very limited (if they were there at all), it is better
to just drop it and require that drivers just implement g_std.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Since this driver provides a g_std op the current_norm field isn't used
anyway, so just drop it.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Since this driver properly implements g_std, the current_norm field is
actually unused anyway.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
current_norm use is deprecated because it is per-devicenode and if you
have more device nodes all dependent on the same video source, then this
no longer works. Just implement g_std instead.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
