Merge master.kernel.org:/home/rmk/linux-2.6-mmc

* master.kernel.org:/home/rmk/linux-2.6-mmc:
  [ARM] 3457/1: i.MX: SD/MMC support for i.MX/MX1
  [ARM] 3456/1: AT91RM9200 support for 2.6 (MMC/SD driver)

8 files changed, 2300 insertions, 0 deletions

diff --git a/arch/arm/mach-imx/generic.c b/arch/arm/mach-imx/generic.c
index 37613ad6..9d8331b 100644
--- a/arch/arm/mach-imx/generic.c
+++ b/arch/arm/mach-imx/generic.c
@@ -33,6 +33,7 @@
 #include <asm/arch/imx-regs.h>
 
 #include <asm/mach/map.h>
+#include <asm/arch/mmc.h>
 
 void imx_gpio_mode(int gpio_mode)
 {
@@ -175,13 +176,25 @@ static struct resource imx_mmc_resources[] = {
 	},
 };
 
+static u64 imxmmmc_dmamask = 0xffffffffUL;
+
 static struct platform_device imx_mmc_device = {
 	.name		= "imx-mmc",
 	.id		= 0,
+	.dev		= {
+		.dma_mask = &imxmmmc_dmamask,
+		.coherent_dma_mask = 0xffffffff,
+	},
 	.num_resources	= ARRAY_SIZE(imx_mmc_resources),
 	.resource	= imx_mmc_resources,
 };
 
+void __init imx_set_mmc_info(struct imxmmc_platform_data *info)
+{
+	imx_mmc_device.dev.platform_data = info;
+}
+EXPORT_SYMBOL(imx_set_mmc_info);
+
 static struct resource imx_uart1_resources[] = {
 	[0] = {
 		.start	= 0x00206000,
diff --git a/drivers/mmc/Kconfig b/drivers/mmc/Kconfig
index 7cc162e..003b077 100644
--- a/drivers/mmc/Kconfig
+++ b/drivers/mmc/Kconfig
@@ -91,4 +91,22 @@ config MMC_AU1X
 
 	  If unsure, say N.
 
+config MMC_AT91RM9200
+	tristate "AT91RM9200 SD/MMC Card Interface support"
+	depends on ARCH_AT91RM9200 && MMC
+	help
+	  This selects the AT91RM9200 MCI controller.
+
+	  If unsure, say N.
+
+config MMC_IMX
+	tristate "Motorola i.MX Multimedia Card Interface support"
+	depends on ARCH_IMX && MMC
+	help
+	  This selects the Motorola i.MX Multimedia card Interface.
+	  If you have a i.MX platform with a Multimedia Card slot,
+	  say Y or M here.
+
+	  If unsure, say N.
+
 endmenu
diff --git a/drivers/mmc/Makefile b/drivers/mmc/Makefile
index c7c34aa..d2957e3 100644
--- a/drivers/mmc/Makefile
+++ b/drivers/mmc/Makefile
@@ -17,10 +17,12 @@ obj-$(CONFIG_MMC_BLOCK)		+= mmc_block.o
 #
 obj-$(CONFIG_MMC_ARMMMCI)	+= mmci.o
 obj-$(CONFIG_MMC_PXA)		+= pxamci.o
+obj-$(CONFIG_MMC_IMX)		+= imxmmc.o
 obj-$(CONFIG_MMC_SDHCI)		+= sdhci.o
 obj-$(CONFIG_MMC_WBSD)		+= wbsd.o
 obj-$(CONFIG_MMC_AU1X)		+= au1xmmc.o
 obj-$(CONFIG_MMC_OMAP)		+= omap.o
+obj-$(CONFIG_MMC_AT91RM9200)	+= at91_mci.o
 
 mmc_core-y := mmc.o mmc_queue.o mmc_sysfs.o
 
diff --git a/drivers/mmc/at91_mci.c b/drivers/mmc/at91_mci.c
new file mode 100644
index 0000000..6061c2d
--- /dev/null
+++ b/drivers/mmc/at91_mci.c
@@ -0,0 +1,988 @@
+/*
+ *  linux/drivers/mmc/at91_mci.c - ATMEL AT91RM9200 MCI Driver
+ *
+ *  Copyright (C) 2005 Cougar Creek Computing Devices Ltd, All Rights Reserved
+ *
+ *  Copyright (C) 2006 Malcolm Noyes
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/*
+   This is the AT91RM9200 MCI driver that has been tested with both MMC cards
+   and SD-cards.  Boards that support write protect are now supported.
+   The CCAT91SBC001 board does not support SD cards.
+
+   The three entry points are at91_mci_request, at91_mci_set_ios
+   and at91_mci_get_ro.
+
+   SET IOS
+     This configures the device to put it into the correct mode and clock speed
+     required.
+
+   MCI REQUEST
+     MCI request processes the commands sent in the mmc_request structure. This
+     can consist of a processing command and a stop command in the case of
+     multiple block transfers.
+
+     There are three main types of request, commands, reads and writes.
+
+     Commands are straight forward. The command is submitted to the controller and
+     the request function returns. When the controller generates an interrupt to indicate
+     the command is finished, the response to the command are read and the mmc_request_done
+     function called to end the request.
+
+     Reads and writes work in a similar manner to normal commands but involve the PDC (DMA)
+     controller to manage the transfers.
+
+     A read is done from the controller directly to the scatterlist passed in from the request.
+     Due to a bug in the controller, when a read is completed, all the words are byte
+     swapped in the scatterlist buffers.
+
+     The sequence of read interrupts is: ENDRX, RXBUFF, CMDRDY
+
+     A write is slightly different in that the bytes to write are read from the scatterlist
+     into a dma memory buffer (this is in case the source buffer should be read only). The
+     entire write buffer is then done from this single dma memory buffer.
+
+     The sequence of write interrupts is: ENDTX, TXBUFE, NOTBUSY, CMDRDY
+
+   GET RO
+     Gets the status of the write protect pin, if available.
+*/
+
+#include <linux/config.h>
+#include <linux/module.h>
+#include <linux/moduleparam.h>
+#include <linux/init.h>
+#include <linux/ioport.h>
+#include <linux/platform_device.h>
+#include <linux/interrupt.h>
+#include <linux/blkdev.h>
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/dma-mapping.h>
+#include <linux/clk.h>
+
+#include <linux/mmc/host.h>
+#include <linux/mmc/protocol.h>
+
+#include <asm/io.h>
+#include <asm/irq.h>
+#include <asm/mach/mmc.h>
+#include <asm/arch/board.h>
+#include <asm/arch/gpio.h>
+#include <asm/arch/at91rm9200_mci.h>
+#include <asm/arch/at91rm9200_pdc.h>
+
+#define DRIVER_NAME "at91_mci"
+
+#undef	SUPPORT_4WIRE
+
+#ifdef CONFIG_MMC_DEBUG
+#define DBG(fmt...)	\
+	printk(fmt)
+#else
+#define DBG(fmt...)	do { } while (0)
+#endif
+
+static struct clk *mci_clk;
+
+#define FL_SENT_COMMAND (1 << 0)
+#define FL_SENT_STOP (1 << 1)
+
+
+
+/*
+ * Read from a MCI register.
+ */
+static inline unsigned long at91_mci_read(unsigned int reg)
+{
+	void __iomem *mci_base = (void __iomem *)AT91_VA_BASE_MCI;
+
+	return __raw_readl(mci_base + reg);
+}
+
+/*
+ * Write to a MCI register.
+ */
+static inline void at91_mci_write(unsigned int reg, unsigned long value)
+{
+        void __iomem *mci_base = (void __iomem *)AT91_VA_BASE_MCI;
+
+        __raw_writel(value, mci_base + reg);
+}
+
+/*
+ * Low level type for this driver
+ */
+struct at91mci_host
+{
+	struct mmc_host *mmc;
+	struct mmc_command *cmd;
+	struct mmc_request *request;
+
+	struct at91_mmc_data *board;
+	int present;
+
+	/*
+	 * Flag indicating when the command has been sent. This is used to
+	 * work out whether or not to send the stop
+	 */
+	unsigned int flags;
+	/* flag for current bus settings */
+	u32 bus_mode;
+
+	/* DMA buffer used for transmitting */
+	unsigned int* buffer;
+	dma_addr_t physical_address;
+	unsigned int total_length;
+
+	/* Latest in the scatterlist that has been enabled for transfer, but not freed */
+	int in_use_index;
+
+	/* Latest in the scatterlist that has been enabled for transfer */
+	int transfer_index;
+};
+
+/*
+ * Copy from sg to a dma block - used for transfers
+ */
+static inline void at91mci_sg_to_dma(struct at91mci_host *host, struct mmc_data *data)
+{
+	unsigned int len, i, size;
+	unsigned *dmabuf = host->buffer;
+
+	size = host->total_length;
+	len = data->sg_len;
+
+	/*
+	 * Just loop through all entries. Size might not
+	 * be the entire list though so make sure that
+	 * we do not transfer too much.
+	 */
+	for (i = 0; i < len; i++) {
+		struct scatterlist *sg;
+		int amount;
+		int index;
+		unsigned int *sgbuffer;
+
+		sg = &data->sg[i];
+
+		sgbuffer = kmap_atomic(sg->page, KM_BIO_SRC_IRQ) + sg->offset;
+		amount = min(size, sg->length);
+		size -= amount;
+		amount /= 4;
+
+		for (index = 0; index < amount; index++)
+			*dmabuf++ = swab32(sgbuffer[index]);
+
+		kunmap_atomic(sgbuffer, KM_BIO_SRC_IRQ);
+
+		if (size == 0)
+			break;
+	}
+
+	/*
+	 * Check that we didn't get a request to transfer
+	 * more data than can fit into the SG list.
+	 */
+	BUG_ON(size != 0);
+}
+
+/*
+ * Prepare a dma read
+ */
+static void at91mci_pre_dma_read(struct at91mci_host *host)
+{
+	int i;
+	struct scatterlist *sg;
+	struct mmc_command *cmd;
+	struct mmc_data *data;
+
+	DBG("pre dma read\n");
+
+	cmd = host->cmd;
+	if (!cmd) {
+		DBG("no command\n");
+		return;
+	}
+
+	data = cmd->data;
+	if (!data) {
+		DBG("no data\n");
+		return;
+	}
+
+	for (i = 0; i < 2; i++) {
+		/* nothing left to transfer */
+		if (host->transfer_index >= data->sg_len) {
+			DBG("Nothing left to transfer (index = %d)\n", host->transfer_index);
+			break;
+		}
+
+		/* Check to see if this needs filling */
+		if (i == 0) {
+			if (at91_mci_read(AT91_PDC_RCR) != 0) {
+				DBG("Transfer active in current\n");
+				continue;
+			}
+		}
+		else {
+			if (at91_mci_read(AT91_PDC_RNCR) != 0) {
+				DBG("Transfer active in next\n");
+				continue;
+			}
+		}
+
+		/* Setup the next transfer */
+		DBG("Using transfer index %d\n", host->transfer_index);
+
+		sg = &data->sg[host->transfer_index++];
+		DBG("sg = %p\n", sg);
+
+		sg->dma_address = dma_map_page(NULL, sg->page, sg->offset, sg->length, DMA_FROM_DEVICE);
+
+		DBG("dma address = %08X, length = %d\n", sg->dma_address, sg->length);
+
+		if (i == 0) {
+			at91_mci_write(AT91_PDC_RPR, sg->dma_address);
+			at91_mci_write(AT91_PDC_RCR, sg->length / 4);
+		}
+		else {
+			at91_mci_write(AT91_PDC_RNPR, sg->dma_address);
+			at91_mci_write(AT91_PDC_RNCR, sg->length / 4);
+		}
+	}
+
+	DBG("pre dma read done\n");
+}
+
+/*
+ * Handle after a dma read
+ */
+static void at91mci_post_dma_read(struct at91mci_host *host)
+{
+	struct mmc_command *cmd;
+	struct mmc_data *data;
+
+	DBG("post dma read\n");
+
+	cmd = host->cmd;
+	if (!cmd) {
+		DBG("no command\n");
+		return;
+	}
+
+	data = cmd->data;
+	if (!data) {
+		DBG("no data\n");
+		return;
+	}
+
+	while (host->in_use_index < host->transfer_index) {
+		unsigned int *buffer;
+		int index;
+		int len;
+
+		struct scatterlist *sg;
+
+		DBG("finishing index %d\n", host->in_use_index);
+
+		sg = &data->sg[host->in_use_index++];
+
+		DBG("Unmapping page %08X\n", sg->dma_address);
+
+		dma_unmap_page(NULL, sg->dma_address, sg->length, DMA_FROM_DEVICE);
+
+		/* Swap the contents of the buffer */
+		buffer = kmap_atomic(sg->page, KM_BIO_SRC_IRQ) + sg->offset;
+		DBG("buffer = %p, length = %d\n", buffer, sg->length);
+
+		data->bytes_xfered += sg->length;
+
+		len = sg->length / 4;
+
+		for (index = 0; index < len; index++) {
+			buffer[index] = swab32(buffer[index]);
+		}
+		kunmap_atomic(buffer, KM_BIO_SRC_IRQ);
+		flush_dcache_page(sg->page);
+	}
+
+	/* Is there another transfer to trigger? */
+	if (host->transfer_index < data->sg_len)
+		at91mci_pre_dma_read(host);
+	else {
+		at91_mci_write(AT91_MCI_IER, AT91_MCI_RXBUFF);
+		at91_mci_write(AT91_PDC_PTCR, AT91_PDC_RXTDIS | AT91_PDC_TXTDIS);
+	}
+
+	DBG("post dma read done\n");
+}
+
+/*
+ * Handle transmitted data
+ */
+static void at91_mci_handle_transmitted(struct at91mci_host *host)
+{
+	struct mmc_command *cmd;
+	struct mmc_data *data;
+
+	DBG("Handling the transmit\n");
+
+	/* Disable the transfer */
+	at91_mci_write(AT91_PDC_PTCR, AT91_PDC_RXTDIS | AT91_PDC_TXTDIS);
+
+	/* Now wait for cmd ready */
+	at91_mci_write(AT91_MCI_IDR, AT91_MCI_TXBUFE);
+	at91_mci_write(AT91_MCI_IER, AT91_MCI_NOTBUSY);
+
+	cmd = host->cmd;
+	if (!cmd) return;
+
+	data = cmd->data;
+	if (!data) return;
+
+	data->bytes_xfered = host->total_length;
+}
+
+/*
+ * Enable the controller
+ */
+static void at91_mci_enable(void)
+{
+	at91_mci_write(AT91_MCI_CR, AT91_MCI_MCIEN);
+	at91_mci_write(AT91_MCI_IDR, 0xFFFFFFFF);
+	at91_mci_write(AT91_MCI_DTOR, AT91_MCI_DTOMUL_1M | AT91_MCI_DTOCYC);
+	at91_mci_write(AT91_MCI_MR, 0x834A);
+	at91_mci_write(AT91_MCI_SDCR, 0x0);
+}
+
+/*
+ * Disable the controller
+ */
+static void at91_mci_disable(void)
+{
+	at91_mci_write(AT91_MCI_CR, AT91_MCI_MCIDIS | AT91_MCI_SWRST);
+}
+
+/*
+ * Send a command
+ * return the interrupts to enable
+ */
+static unsigned int at91_mci_send_command(struct at91mci_host *host, struct mmc_command *cmd)
+{
+	unsigned int cmdr, mr;
+	unsigned int block_length;
+	struct mmc_data *data = cmd->data;
+
+	unsigned int blocks;
+	unsigned int ier = 0;
+
+	host->cmd = cmd;
+
+	/* Not sure if this is needed */
+#if 0
+	if ((at91_mci_read(AT91_MCI_SR) & AT91_MCI_RTOE) && (cmd->opcode == 1)) {
+		DBG("Clearing timeout\n");
+		at91_mci_write(AT91_MCI_ARGR, 0);
+		at91_mci_write(AT91_MCI_CMDR, AT91_MCI_OPDCMD);
+		while (!(at91_mci_read(AT91_MCI_SR) & AT91_MCI_CMDRDY)) {
+			/* spin */
+			DBG("Clearing: SR = %08X\n", at91_mci_read(AT91_MCI_SR));
+		}
+	}
+#endif
+	cmdr = cmd->opcode;
+
+	if (mmc_resp_type(cmd) == MMC_RSP_NONE)
+		cmdr |= AT91_MCI_RSPTYP_NONE;
+	else {
+		/* if a response is expected then allow maximum response latancy */
+		cmdr |= AT91_MCI_MAXLAT;
+		/* set 136 bit response for R2, 48 bit response otherwise */
+		if (mmc_resp_type(cmd) == MMC_RSP_R2)
+			cmdr |= AT91_MCI_RSPTYP_136;
+		else
+			cmdr |= AT91_MCI_RSPTYP_48;
+	}
+
+	if (data) {
+		block_length = 1 << data->blksz_bits;
+		blocks = data->blocks;
+
+		/* always set data start - also set direction flag for read */
+		if (data->flags & MMC_DATA_READ)
+			cmdr |= (AT91_MCI_TRDIR | AT91_MCI_TRCMD_START);
+		else if (data->flags & MMC_DATA_WRITE)
+			cmdr |= AT91_MCI_TRCMD_START;
+
+		if (data->flags & MMC_DATA_STREAM)
+			cmdr |= AT91_MCI_TRTYP_STREAM;
+		if (data->flags & MMC_DATA_MULTI)
+			cmdr |= AT91_MCI_TRTYP_MULTIPLE;
+	}
+	else {
+		block_length = 0;
+		blocks = 0;
+	}
+
+	if (cmd->opcode == MMC_STOP_TRANSMISSION)
+		cmdr |= AT91_MCI_TRCMD_STOP;
+
+	if (host->bus_mode == MMC_BUSMODE_OPENDRAIN)
+		cmdr |= AT91_MCI_OPDCMD;
+
+	/*
+	 * Set the arguments and send the command
+	 */
+	DBG("Sending command %d as %08X, arg = %08X, blocks = %d, length = %d (MR = %08lX)\n",
+		cmd->opcode, cmdr, cmd->arg, blocks, block_length, at91_mci_read(AT91_MCI_MR));
+
+	if (!data) {
+		at91_mci_write(AT91_PDC_PTCR, AT91_PDC_TXTDIS | AT91_PDC_RXTDIS);
+		at91_mci_write(AT91_PDC_RPR, 0);
+		at91_mci_write(AT91_PDC_RCR, 0);
+		at91_mci_write(AT91_PDC_RNPR, 0);
+		at91_mci_write(AT91_PDC_RNCR, 0);
+		at91_mci_write(AT91_PDC_TPR, 0);
+		at91_mci_write(AT91_PDC_TCR, 0);
+		at91_mci_write(AT91_PDC_TNPR, 0);
+		at91_mci_write(AT91_PDC_TNCR, 0);
+
+		at91_mci_write(AT91_MCI_ARGR, cmd->arg);
+		at91_mci_write(AT91_MCI_CMDR, cmdr);
+		return AT91_MCI_CMDRDY;
+	}
+
+	mr = at91_mci_read(AT91_MCI_MR) & 0x7fff;	/* zero block length and PDC mode */
+	at91_mci_write(AT91_MCI_MR, mr | (block_length << 16) | AT91_MCI_PDCMODE);
+
+	/*
+	 * Disable the PDC controller
+	 */
+	at91_mci_write(AT91_PDC_PTCR, AT91_PDC_RXTDIS | AT91_PDC_TXTDIS);
+
+	if (cmdr & AT91_MCI_TRCMD_START) {
+		data->bytes_xfered = 0;
+		host->transfer_index = 0;
+		host->in_use_index = 0;
+		if (cmdr & AT91_MCI_TRDIR) {
+			/*
+			 * Handle a read
+			 */
+			host->buffer = NULL;
+			host->total_length = 0;
+
+			at91mci_pre_dma_read(host);
+			ier = AT91_MCI_ENDRX /* | AT91_MCI_RXBUFF */;
+		}
+		else {
+			/*
+			 * Handle a write
+			 */
+			host->total_length = block_length * blocks;
+			host->buffer = dma_alloc_coherent(NULL,
+						  host->total_length,
+						  &host->physical_address, GFP_KERNEL);
+
+			at91mci_sg_to_dma(host, data);
+
+			DBG("Transmitting %d bytes\n", host->total_length);
+
+			at91_mci_write(AT91_PDC_TPR, host->physical_address);
+			at91_mci_write(AT91_PDC_TCR, host->total_length / 4);
+			ier = AT91_MCI_TXBUFE;
+		}
+	}
+
+	/*
+	 * Send the command and then enable the PDC - not the other way round as
+	 * the data sheet says
+	 */
+
+	at91_mci_write(AT91_MCI_ARGR, cmd->arg);
+	at91_mci_write(AT91_MCI_CMDR, cmdr);
+
+	if (cmdr & AT91_MCI_TRCMD_START) {
+		if (cmdr & AT91_MCI_TRDIR)
+			at91_mci_write(AT91_PDC_PTCR, AT91_PDC_RXTEN);
+		else
+			at91_mci_write(AT91_PDC_PTCR, AT91_PDC_TXTEN);
+	}
+	return ier;
+}
+
+/*
+ * Wait for a command to complete
+ */
+static void at91mci_process_command(struct at91mci_host *host, struct mmc_command *cmd)
+{
+	unsigned int ier;
+
+	ier = at91_mci_send_command(host, cmd);
+
+	DBG("setting ier to %08X\n", ier);
+
+	/* Stop on errors or the required value */
+	at91_mci_write(AT91_MCI_IER, 0xffff0000 | ier);
+}
+
+/*
+ * Process the next step in the request
+ */
+static void at91mci_process_next(struct at91mci_host *host)
+{
+	if (!(host->flags & FL_SENT_COMMAND)) {
+		host->flags |= FL_SENT_COMMAND;
+		at91mci_process_command(host, host->request->cmd);
+	}
+	else if ((!(host->flags & FL_SENT_STOP)) && host->request->stop) {
+		host->flags |= FL_SENT_STOP;
+		at91mci_process_command(host, host->request->stop);
+	}
+	else
+		mmc_request_done(host->mmc, host->request);
+}
+
+/*
+ * Handle a command that has been completed
+ */
+static void at91mci_completed_command(struct at91mci_host *host)
+{
+	struct mmc_command *cmd = host->cmd;
+	unsigned int status;
+
+	at91_mci_write(AT91_MCI_IDR, 0xffffffff);
+
+	cmd->resp[0] = at91_mci_read(AT91_MCI_RSPR(0));
+	cmd->resp[1] = at91_mci_read(AT91_MCI_RSPR(1));
+	cmd->resp[2] = at91_mci_read(AT91_MCI_RSPR(2));
+	cmd->resp[3] = at91_mci_read(AT91_MCI_RSPR(3));
+
+	if (host->buffer) {
+		dma_free_coherent(NULL, host->total_length, host->buffer, host->physical_address);
+		host->buffer = NULL;
+	}
+
+	status = at91_mci_read(AT91_MCI_SR);
+
+	DBG("Status = %08X [%08X %08X %08X %08X]\n",
+		 status, cmd->resp[0], cmd->resp[1], cmd->resp[2], cmd->resp[3]);
+
+	if (status & (AT91_MCI_RINDE | AT91_MCI_RDIRE | AT91_MCI_RCRCE |
+			AT91_MCI_RENDE | AT91_MCI_RTOE | AT91_MCI_DCRCE |
+			AT91_MCI_DTOE | AT91_MCI_OVRE | AT91_MCI_UNRE)) {
+		if ((status & AT91_MCI_RCRCE) &&
+			((cmd->opcode == MMC_SEND_OP_COND) || (cmd->opcode == SD_APP_OP_COND))) {
+			cmd->error = MMC_ERR_NONE;
+		}
+		else {
+			if (status & (AT91_MCI_RTOE | AT91_MCI_DTOE))
+				cmd->error = MMC_ERR_TIMEOUT;
+			else if (status & (AT91_MCI_RCRCE | AT91_MCI_DCRCE))
+				cmd->error = MMC_ERR_BADCRC;
+			else if (status & (AT91_MCI_OVRE | AT91_MCI_UNRE))
+				cmd->error = MMC_ERR_FIFO;
+			else
+				cmd->error = MMC_ERR_FAILED;
+
+			DBG("Error detected and set to %d (cmd = %d, retries = %d)\n",
+				 cmd->error, cmd->opcode, cmd->retries);
+		}
+	}
+	else
+		cmd->error = MMC_ERR_NONE;
+
+	at91mci_process_next(host);
+}
+
+/*
+ * Handle an MMC request
+ */
+static void at91_mci_request(struct mmc_host *mmc, struct mmc_request *mrq)
+{
+	struct at91mci_host *host = mmc_priv(mmc);
+	host->request = mrq;
+	host->flags = 0;
+
+	at91mci_process_next(host);
+}
+
+/*
+ * Set the IOS
+ */
+static void at91_mci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
+{
+	int clkdiv;
+	struct at91mci_host *host = mmc_priv(mmc);
+	unsigned long at91_master_clock = clk_get_rate(mci_clk);
+
+	DBG("Clock %uHz, busmode %u, powermode %u, Vdd %u\n",
+		ios->clock, ios->bus_mode, ios->power_mode, ios->vdd);
+
+	if (host)
+		host->bus_mode = ios->bus_mode;
+	else
+		printk("MMC: No host for bus_mode\n");
+
+	if (ios->clock == 0) {
+		/* Disable the MCI controller */
+		at91_mci_write(AT91_MCI_CR, AT91_MCI_MCIDIS);
+		clkdiv = 0;
+	}
+	else {
+		/* Enable the MCI controller */
+		at91_mci_write(AT91_MCI_CR, AT91_MCI_MCIEN);
+
+		if ((at91_master_clock % (ios->clock * 2)) == 0)
+			clkdiv = ((at91_master_clock / ios->clock) / 2) - 1;
+		else
+			clkdiv = (at91_master_clock / ios->clock) / 2;
+
+		DBG("clkdiv = %d. mcck = %ld\n", clkdiv,
+			at91_master_clock / (2 * (clkdiv + 1)));
+	}
+	if (ios->bus_width == MMC_BUS_WIDTH_4 && host->board->wire4) {
+		DBG("MMC: Setting controller bus width to 4\n");
+		at91_mci_write(AT91_MCI_SDCR, at91_mci_read(AT91_MCI_SDCR) | AT91_MCI_SDCBUS);
+	}
+	else {
+		DBG("MMC: Setting controller bus width to 1\n");
+		at91_mci_write(AT91_MCI_SDCR, at91_mci_read(AT91_MCI_SDCR) & ~AT91_MCI_SDCBUS);
+	}
+
+	/* Set the clock divider */
+	at91_mci_write(AT91_MCI_MR, (at91_mci_read(AT91_MCI_MR) & ~AT91_MCI_CLKDIV) | clkdiv);
+
+	/* maybe switch power to the card */
+	if (host && host->board->vcc_pin) {
+		switch (ios->power_mode) {
+			case MMC_POWER_OFF:
+				at91_set_gpio_output(host->board->vcc_pin, 0);
+				break;
+			case MMC_POWER_UP:
+			case MMC_POWER_ON:
+				at91_set_gpio_output(host->board->vcc_pin, 1);
+				break;
+		}
+	}
+}
+
+/*
+ * Handle an interrupt
+ */
+static irqreturn_t at91_mci_irq(int irq, void *devid, struct pt_regs *regs)
+{
+	struct at91mci_host *host = devid;
+	int completed = 0;
+
+	unsigned int int_status;
+
+	if (host == NULL)
+		return IRQ_HANDLED;
+
+	int_status = at91_mci_read(AT91_MCI_SR);
+	DBG("MCI irq: status = %08X, %08lX, %08lX\n", int_status, at91_mci_read(AT91_MCI_IMR),
+		int_status & at91_mci_read(AT91_MCI_IMR));
+
+	if ((int_status & at91_mci_read(AT91_MCI_IMR)) & 0xffff0000)
+		completed = 1;
+
+	int_status &= at91_mci_read(AT91_MCI_IMR);
+
+	if (int_status & AT91_MCI_UNRE)
+		DBG("MMC: Underrun error\n");
+	if (int_status & AT91_MCI_OVRE)
+		DBG("MMC: Overrun error\n");
+	if (int_status & AT91_MCI_DTOE)
+		DBG("MMC: Data timeout\n");
+	if (int_status & AT91_MCI_DCRCE)
+		DBG("MMC: CRC error in data\n");
+	if (int_status & AT91_MCI_RTOE)
+		DBG("MMC: Response timeout\n");
+	if (int_status & AT91_MCI_RENDE)
+		DBG("MMC: Response end bit error\n");
+	if (int_status & AT91_MCI_RCRCE)
+		DBG("MMC: Response CRC error\n");
+	if (int_status & AT91_MCI_RDIRE)
+		DBG("MMC: Response direction error\n");
+	if (int_status & AT91_MCI_RINDE)
+		DBG("MMC: Response index error\n");
+
+	/* Only continue processing if no errors */
+	if (!completed) {
+		if (int_status & AT91_MCI_TXBUFE) {
+			DBG("TX buffer empty\n");
+			at91_mci_handle_transmitted(host);
+		}
+
+		if (int_status & AT91_MCI_RXBUFF) {
+			DBG("RX buffer full\n");
+			at91_mci_write(AT91_MCI_IER, AT91_MCI_CMDRDY);
+		}
+
+		if (int_status & AT91_MCI_ENDTX) {
+			DBG("Transmit has ended\n");
+		}
+
+		if (int_status & AT91_MCI_ENDRX) {
+			DBG("Receive has ended\n");
+			at91mci_post_dma_read(host);
+		}
+
+		if (int_status & AT91_MCI_NOTBUSY) {
+			DBG("Card is ready\n");
+			at91_mci_write(AT91_MCI_IER, AT91_MCI_CMDRDY);
+		}
+
+		if (int_status & AT91_MCI_DTIP) {
+			DBG("Data transfer in progress\n");
+		}
+
+		if (int_status & AT91_MCI_BLKE) {
+			DBG("Block transfer has ended\n");
+		}
+
+		if (int_status & AT91_MCI_TXRDY) {
+			DBG("Ready to transmit\n");
+		}
+
+		if (int_status & AT91_MCI_RXRDY) {
+			DBG("Ready to receive\n");
+		}
+
+		if (int_status & AT91_MCI_CMDRDY) {
+			DBG("Command ready\n");
+			completed = 1;
+		}
+	}
+	at91_mci_write(AT91_MCI_IDR, int_status);
+
+	if (completed) {
+		DBG("Completed command\n");
+		at91_mci_write(AT91_MCI_IDR, 0xffffffff);
+		at91mci_completed_command(host);
+	}
+
+	return IRQ_HANDLED;
+}
+
+static irqreturn_t at91_mmc_det_irq(int irq, void *_host, struct pt_regs *regs)
+{
+	struct at91mci_host *host = _host;
+	int present = !at91_get_gpio_value(irq);
+
+	/*
+	 * we expect this irq on both insert and remove,
+	 * and use a short delay to debounce.
+	 */
+	if (present != host->present) {
+		host->present = present;
+		DBG("%s: card %s\n", mmc_hostname(host->mmc),
+			present ? "insert" : "remove");
+		if (!present) {
+			DBG("****** Resetting SD-card bus width ******\n");
+			at91_mci_write(AT91_MCI_SDCR, 0);
+		}
+		mmc_detect_change(host->mmc, msecs_to_jiffies(100));
+	}
+	return IRQ_HANDLED;
+}
+
+int at91_mci_get_ro(struct mmc_host *mmc)
+{
+	int read_only = 0;
+	struct at91mci_host *host = mmc_priv(mmc);
+
+	if (host->board->wp_pin) {
+		read_only = at91_get_gpio_value(host->board->wp_pin);
+		printk(KERN_WARNING "%s: card is %s\n", mmc_hostname(mmc),
+				(read_only ? "read-only" : "read-write") );
+	}
+	else {
+		printk(KERN_WARNING "%s: host does not support reading read-only "
+				"switch.  Assuming write-enable.\n", mmc_hostname(mmc));
+	}
+	return read_only;
+}
+
+static struct mmc_host_ops at91_mci_ops = {
+	.request	= at91_mci_request,
+	.set_ios	= at91_mci_set_ios,
+	.get_ro		= at91_mci_get_ro,
+};
+
+/*
+ * Probe for the device
+ */
+static int at91_mci_probe(struct platform_device *pdev)
+{
+	struct mmc_host *mmc;
+	struct at91mci_host *host;
+	int ret;
+
+	DBG("Probe MCI devices\n");
+	at91_mci_disable();
+	at91_mci_enable();
+
+	mmc = mmc_alloc_host(sizeof(struct at91mci_host), &pdev->dev);
+	if (!mmc) {
+		DBG("Failed to allocate mmc host\n");
+		return -ENOMEM;
+	}
+
+	mmc->ops = &at91_mci_ops;
+	mmc->f_min = 375000;
+	mmc->f_max = 25000000;
+	mmc->ocr_avail = MMC_VDD_32_33 | MMC_VDD_33_34;
+
+	host = mmc_priv(mmc);
+	host->mmc = mmc;
+	host->buffer = NULL;
+	host->bus_mode = 0;
+	host->board = pdev->dev.platform_data;
+	if (host->board->wire4) {
+#ifdef SUPPORT_4WIRE
+		mmc->caps |= MMC_CAP_4_BIT_DATA;
+#else
+		printk("MMC: 4 wire bus mode not supported by this driver - using 1 wire\n");
+#endif
+	}
+
+	/*
+	 * Get Clock
+	 */
+	mci_clk = clk_get(&pdev->dev, "mci_clk");
+	if (!mci_clk) {
+		printk(KERN_ERR "AT91 MMC: no clock defined.\n");
+		return -ENODEV;
+	}
+	clk_enable(mci_clk);			/* Enable the peripheral clock */
+
+	/*
+	 * Allocate the MCI interrupt
+	 */
+	ret = request_irq(AT91_ID_MCI, at91_mci_irq, SA_SHIRQ, DRIVER_NAME, host);
+	if (ret) {
+		DBG("Failed to request MCI interrupt\n");
+		return ret;
+	}
+
+	platform_set_drvdata(pdev, mmc);
+
+	/*
+	 * Add host to MMC layer
+	 */
+	if (host->board->det_pin)
+		host->present = !at91_get_gpio_value(host->board->det_pin);
+	else
+		host->present = -1;
+
+	mmc_add_host(mmc);
+
+	/*
+	 * monitor card insertion/removal if we can
+	 */
+	if (host->board->det_pin) {
+		ret = request_irq(host->board->det_pin, at91_mmc_det_irq,
+				SA_SAMPLE_RANDOM, DRIVER_NAME, host);
+		if (ret)
+			DBG("couldn't allocate MMC detect irq\n");
+	}
+
+	DBG(KERN_INFO "Added MCI driver\n");
+
+	return 0;
+}
+
+/*
+ * Remove a device
+ */
+static int at91_mci_remove(struct platform_device *pdev)
+{
+	struct mmc_host *mmc = platform_get_drvdata(pdev);
+	struct at91mci_host *host;
+
+	if (!mmc)
+		return -1;
+
+	host = mmc_priv(mmc);
+
+	if (host->present != -1) {
+		free_irq(host->board->det_pin, host);
+		cancel_delayed_work(&host->mmc->detect);
+	}
+
+	mmc_remove_host(mmc);
+	at91_mci_disable();
+	free_irq(AT91_ID_MCI, host);
+	mmc_free_host(mmc);
+
+	clk_disable(mci_clk);				/* Disable the peripheral clock */
+	clk_put(mci_clk);
+
+	platform_set_drvdata(pdev, NULL);
+
+	DBG("Removed\n");
+
+	return 0;
+}
+
+#ifdef CONFIG_PM
+static int at91_mci_suspend(struct platform_device *pdev, pm_message_t state)
+{
+	struct mmc_host *mmc = platform_get_drvdata(pdev);
+	int ret = 0;
+
+	if (mmc)
+		ret = mmc_suspend_host(mmc, state);
+
+	return ret;
+}
+
+static int at91_mci_resume(struct platform_device *pdev)
+{
+	struct mmc_host *mmc = platform_get_drvdata(pdev);
+	int ret = 0;
+
+	if (mmc)
+		ret = mmc_resume_host(mmc);
+
+	return ret;
+}
+#else
+#define at91_mci_suspend	NULL
+#define at91_mci_resume		NULL
+#endif
+
+static struct platform_driver at91_mci_driver = {
+	.probe		= at91_mci_probe,
+	.remove		= at91_mci_remove,
+	.suspend	= at91_mci_suspend,
+	.resume		= at91_mci_resume,
+	.driver		= {
+		.name	= DRIVER_NAME,
+		.owner	= THIS_MODULE,
+	},
+};
+
+static int __init at91_mci_init(void)
+{
+	return platform_driver_register(&at91_mci_driver);
+}
+
+static void __exit at91_mci_exit(void)
+{
+	platform_driver_unregister(&at91_mci_driver);
+}
+
+module_init(at91_mci_init);
+module_exit(at91_mci_exit);
+
+MODULE_DESCRIPTION("AT91 Multimedia Card Interface driver");
+MODULE_AUTHOR("Nick Randell");
+MODULE_LICENSE("GPL");
diff --git a/drivers/mmc/imxmmc.c b/drivers/mmc/imxmmc.c
new file mode 100644
index 0000000..ffb7f55
--- /dev/null
+++ b/drivers/mmc/imxmmc.c
@@ -0,0 +1,1096 @@
+/*
+ *  linux/drivers/mmc/imxmmc.c - Motorola i.MX MMCI driver
+ *
+ *  Copyright (C) 2004 Sascha Hauer, Pengutronix <sascha@saschahauer.de>
+ *  Copyright (C) 2006 Pavel Pisa, PiKRON <ppisa@pikron.com>
+ *
+ *  derived from pxamci.c by Russell King
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ *  2005-04-17 Pavel Pisa <pisa@cmp.felk.cvut.cz>
+ *             Changed to conform redesigned i.MX scatter gather DMA interface
+ *
+ *  2005-11-04 Pavel Pisa <pisa@cmp.felk.cvut.cz>
+ *             Updated for 2.6.14 kernel
+ *
+ *  2005-12-13 Jay Monkman <jtm@smoothsmoothie.com>
+ *             Found and corrected problems in the write path
+ *
+ *  2005-12-30 Pavel Pisa <pisa@cmp.felk.cvut.cz>
+ *             The event handling rewritten right way in softirq.
+ *             Added many ugly hacks and delays to overcome SDHC
+ *             deficiencies
+ *
+ */
+#include <linux/config.h>
+
+#ifdef CONFIG_MMC_DEBUG
+#define DEBUG
+#else
+#undef  DEBUG
+#endif
+
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/ioport.h>
+#include <linux/platform_device.h>
+#include <linux/interrupt.h>
+#include <linux/blkdev.h>
+#include <linux/dma-mapping.h>
+#include <linux/mmc/host.h>
+#include <linux/mmc/card.h>
+#include <linux/mmc/protocol.h>
+#include <linux/delay.h>
+
+#include <asm/dma.h>
+#include <asm/io.h>
+#include <asm/irq.h>
+#include <asm/sizes.h>
+#include <asm/arch/mmc.h>
+#include <asm/arch/imx-dma.h>
+
+#include "imxmmc.h"
+
+#define DRIVER_NAME "imx-mmc"
+
+#define IMXMCI_INT_MASK_DEFAULT (INT_MASK_BUF_READY | INT_MASK_DATA_TRAN | \
+	              INT_MASK_WRITE_OP_DONE | INT_MASK_END_CMD_RES | \
+		      INT_MASK_AUTO_CARD_DETECT | INT_MASK_DAT0_EN | INT_MASK_SDIO)
+
+struct imxmci_host {
+	struct mmc_host		*mmc;
+	spinlock_t		lock;
+	struct resource		*res;
+	int			irq;
+	imx_dmach_t		dma;
+	unsigned int		clkrt;
+	unsigned int		cmdat;
+	volatile unsigned int	imask;
+	unsigned int		power_mode;
+	unsigned int		present;
+	struct imxmmc_platform_data *pdata;
+
+	struct mmc_request	*req;
+	struct mmc_command	*cmd;
+	struct mmc_data		*data;
+
+	struct timer_list	timer;
+	struct tasklet_struct	tasklet;
+	unsigned int		status_reg;
+	unsigned long		pending_events;
+	/* Next to fields are there for CPU driven transfers to overcome SDHC deficiencies */
+	u16			*data_ptr;
+	unsigned int		data_cnt;
+	atomic_t		stuck_timeout;
+
+	unsigned int		dma_nents;
+	unsigned int		dma_size;
+	unsigned int		dma_dir;
+	int			dma_allocated;
+
+	unsigned char		actual_bus_width;
+};
+
+#define IMXMCI_PEND_IRQ_b	0
+#define IMXMCI_PEND_DMA_END_b	1
+#define IMXMCI_PEND_DMA_ERR_b	2
+#define IMXMCI_PEND_WAIT_RESP_b	3
+#define IMXMCI_PEND_DMA_DATA_b	4
+#define IMXMCI_PEND_CPU_DATA_b	5
+#define IMXMCI_PEND_CARD_XCHG_b	6
+#define IMXMCI_PEND_SET_INIT_b	7
+
+#define IMXMCI_PEND_IRQ_m	(1 << IMXMCI_PEND_IRQ_b)
+#define IMXMCI_PEND_DMA_END_m	(1 << IMXMCI_PEND_DMA_END_b)
+#define IMXMCI_PEND_DMA_ERR_m	(1 << IMXMCI_PEND_DMA_ERR_b)
+#define IMXMCI_PEND_WAIT_RESP_m	(1 << IMXMCI_PEND_WAIT_RESP_b)
+#define IMXMCI_PEND_DMA_DATA_m	(1 << IMXMCI_PEND_DMA_DATA_b)
+#define IMXMCI_PEND_CPU_DATA_m	(1 << IMXMCI_PEND_CPU_DATA_b)
+#define IMXMCI_PEND_CARD_XCHG_m	(1 << IMXMCI_PEND_CARD_XCHG_b)
+#define IMXMCI_PEND_SET_INIT_m	(1 << IMXMCI_PEND_SET_INIT_b)
+
+static void imxmci_stop_clock(struct imxmci_host *host)
+{
+	int i = 0;
+	MMC_STR_STP_CLK &= ~STR_STP_CLK_START_CLK;
+	while(i < 0x1000) {
+	        if(!(i & 0x7f))
+			MMC_STR_STP_CLK |= STR_STP_CLK_STOP_CLK;
+
+		if(!(MMC_STATUS & STATUS_CARD_BUS_CLK_RUN)) {
+			/* Check twice before cut */
+			if(!(MMC_STATUS & STATUS_CARD_BUS_CLK_RUN))
+				return;
+		}
+
+		i++;
+	}
+	dev_dbg(mmc_dev(host->mmc), "imxmci_stop_clock blocked, no luck\n");
+}
+
+static void imxmci_start_clock(struct imxmci_host *host)
+{
+	int i = 0;
+	MMC_STR_STP_CLK &= ~STR_STP_CLK_STOP_CLK;
+	while(i < 0x1000) {
+	        if(!(i & 0x7f))
+			MMC_STR_STP_CLK |= STR_STP_CLK_START_CLK;
+
+		if(MMC_STATUS & STATUS_CARD_BUS_CLK_RUN) {
+			/* Check twice before cut */
+			if(MMC_STATUS & STATUS_CARD_BUS_CLK_RUN)
+				return;
+		}
+
+		i++;
+	}
+	dev_dbg(mmc_dev(host->mmc), "imxmci_start_clock blocked, no luck\n");
+}
+
+static void imxmci_softreset(void)
+{
+	/* reset sequence */
+	MMC_STR_STP_CLK = 0x8;
+	MMC_STR_STP_CLK = 0xD;
+	MMC_STR_STP_CLK = 0x5;
+	MMC_STR_STP_CLK = 0x5;
+	MMC_STR_STP_CLK = 0x5;
+	MMC_STR_STP_CLK = 0x5;
+	MMC_STR_STP_CLK = 0x5;
+	MMC_STR_STP_CLK = 0x5;
+	MMC_STR_STP_CLK = 0x5;
+	MMC_STR_STP_CLK = 0x5;
+
+	MMC_RES_TO = 0xff;
+	MMC_BLK_LEN = 512;
+	MMC_NOB = 1;
+}
+
+static int imxmci_busy_wait_for_status(struct imxmci_host *host,
+			unsigned int *pstat, unsigned int stat_mask,
+			int timeout, const char *where)
+{
+	int loops=0;
+	while(!(*pstat & stat_mask)) {
+		loops+=2;
+		if(loops >= timeout) {
+			dev_dbg(mmc_dev(host->mmc), "busy wait timeout in %s, STATUS = 0x%x (0x%x)\n",
+				where, *pstat, stat_mask);
+			return -1;
+		}
+		udelay(2);
+		*pstat |= MMC_STATUS;
+	}
+	if(!loops)
+		return 0;
+
+	dev_info(mmc_dev(host->mmc), "busy wait for %d usec in %s, STATUS = 0x%x (0x%x)\n",
+		loops, where, *pstat, stat_mask);
+	return loops;
+}
+
+static void imxmci_setup_data(struct imxmci_host *host, struct mmc_data *data)
+{
+	unsigned int nob = data->blocks;
+	unsigned int blksz = 1 << data->blksz_bits;
+	unsigned int datasz = nob * blksz;
+	int i;
+
+	if (data->flags & MMC_DATA_STREAM)
+		nob = 0xffff;
+
+	host->data = data;
+	data->bytes_xfered = 0;
+
+	MMC_NOB = nob;
+	MMC_BLK_LEN = blksz;
+
+	/*
+	 * DMA cannot be used for small block sizes, we have to use CPU driven transfers otherwise.
+	 * We are in big troubles for non-512 byte transfers according to note in the paragraph
+	 * 20.6.7 of User Manual anyway, but we need to be able to transfer SCR at least.
+	 * The situation is even more complex in reality. The SDHC in not able to handle wll
+	 * partial FIFO fills and reads. The length has to be rounded up to burst size multiple.
+	 * This is required for SCR read at least.
+	 */
+	if (datasz < 64) {
+		host->dma_size = datasz;
+		if (data->flags & MMC_DATA_READ) {
+			host->dma_dir = DMA_FROM_DEVICE;
+
+			/* Hack to enable read SCR */
+			if(datasz < 16) {
+				MMC_NOB = 1;
+				MMC_BLK_LEN = 16;
+			}
+		} else {
+			host->dma_dir = DMA_TO_DEVICE;
+		}
+
+		/* Convert back to virtual address */
+		host->data_ptr = (u16*)(page_address(data->sg->page) + data->sg->offset);
+		host->data_cnt = 0;
+
+		clear_bit(IMXMCI_PEND_DMA_DATA_b, &host->pending_events);
+		set_bit(IMXMCI_PEND_CPU_DATA_b, &host->pending_events);
+
+		return;
+	}
+
+	if (data->flags & MMC_DATA_READ) {
+		host->dma_dir = DMA_FROM_DEVICE;
+		host->dma_nents = dma_map_sg(mmc_dev(host->mmc), data->sg,
+						data->sg_len,  host->dma_dir);
+
+		imx_dma_setup_sg(host->dma, data->sg, data->sg_len, datasz,
+			host->res->start + MMC_BUFFER_ACCESS_OFS, DMA_MODE_READ);
+
+		/*imx_dma_setup_mem2dev_ccr(host->dma, DMA_MODE_READ, IMX_DMA_WIDTH_16, CCR_REN);*/
+		CCR(host->dma) = CCR_DMOD_LINEAR | CCR_DSIZ_32 | CCR_SMOD_FIFO | CCR_SSIZ_16 | CCR_REN;
+	} else {
+		host->dma_dir = DMA_TO_DEVICE;
+
+		host->dma_nents = dma_map_sg(mmc_dev(host->mmc), data->sg,
+						data->sg_len,  host->dma_dir);
+
+		imx_dma_setup_sg(host->dma, data->sg, data->sg_len, datasz,
+			host->res->start + MMC_BUFFER_ACCESS_OFS, DMA_MODE_WRITE);
+
+		/*imx_dma_setup_mem2dev_ccr(host->dma, DMA_MODE_WRITE, IMX_DMA_WIDTH_16, CCR_REN);*/
+		CCR(host->dma) = CCR_SMOD_LINEAR | CCR_SSIZ_32 | CCR_DMOD_FIFO | CCR_DSIZ_16 | CCR_REN;
+	}
+
+#if 1	/* This code is there only for consistency checking and can be disabled in future */
+	host->dma_size = 0;
+	for(i=0; i<host->dma_nents; i++)
+		host->dma_size+=data->sg[i].length;
+
+	if (datasz > host->dma_size) {
+		dev_err(mmc_dev(host->mmc), "imxmci_setup_data datasz 0x%x > 0x%x dm_size\n",
+		       datasz, host->dma_size);
+	}
+#endif
+
+	host->dma_size = datasz;
+
+	wmb();
+
+	if(host->actual_bus_width == MMC_BUS_WIDTH_4)
+		BLR(host->dma) = 0;	/* burst 64 byte read / 64 bytes write */
+	else
+		BLR(host->dma) = 16;	/* burst 16 byte read / 16 bytes write */
+
+	RSSR(host->dma) = DMA_REQ_SDHC;
+
+	set_bit(IMXMCI_PEND_DMA_DATA_b, &host->pending_events);
+	clear_bit(IMXMCI_PEND_CPU_DATA_b, &host->pending_events);
+
+	/* start DMA engine for read, write is delayed after initial response */
+	if (host->dma_dir == DMA_FROM_DEVICE) {
+		imx_dma_enable(host->dma);
+	}
+}
+
+static void imxmci_start_cmd(struct imxmci_host *host, struct mmc_command *cmd, unsigned int cmdat)
+{
+	unsigned long flags;
+	u32 imask;
+
+	WARN_ON(host->cmd != NULL);
+	host->cmd = cmd;
+
+	if (cmd->flags & MMC_RSP_BUSY)
+		cmdat |= CMD_DAT_CONT_BUSY;
+
+	switch (mmc_resp_type(cmd)) {
+	case MMC_RSP_R1: /* short CRC, OPCODE */
+	case MMC_RSP_R1B:/* short CRC, OPCODE, BUSY */
+		cmdat |= CMD_DAT_CONT_RESPONSE_FORMAT_R1;
+		break;
+	case MMC_RSP_R2: /* long 136 bit + CRC */
+		cmdat |= CMD_DAT_CONT_RESPONSE_FORMAT_R2;
+		break;
+	case MMC_RSP_R3: /* short */
+		cmdat |= CMD_DAT_CONT_RESPONSE_FORMAT_R3;
+		break;
+	case MMC_RSP_R6: /* short CRC */
+		cmdat |= CMD_DAT_CONT_RESPONSE_FORMAT_R6;
+		break;
+	default:
+		break;
+	}
+
+	if ( test_and_clear_bit(IMXMCI_PEND_SET_INIT_b, &host->pending_events) )
+		cmdat |= CMD_DAT_CONT_INIT; /* This command needs init */
+
+	if ( host->actual_bus_width == MMC_BUS_WIDTH_4 )
+		cmdat |= CMD_DAT_CONT_BUS_WIDTH_4;
+
+	MMC_CMD = cmd->opcode;
+	MMC_ARGH = cmd->arg >> 16;
+	MMC_ARGL = cmd->arg & 0xffff;
+	MMC_CMD_DAT_CONT = cmdat;
+
+	atomic_set(&host->stuck_timeout, 0);
+	set_bit(IMXMCI_PEND_WAIT_RESP_b, &host->pending_events);
+
+
+	imask = IMXMCI_INT_MASK_DEFAULT;
+	imask &= ~INT_MASK_END_CMD_RES;
+	if ( cmdat & CMD_DAT_CONT_DATA_ENABLE ) {
+		/*imask &= ~INT_MASK_BUF_READY;*/
+		imask &= ~INT_MASK_DATA_TRAN;
+		if ( cmdat & CMD_DAT_CONT_WRITE )
+			imask &= ~INT_MASK_WRITE_OP_DONE;
+		if(test_bit(IMXMCI_PEND_CPU_DATA_b, &host->pending_events))
+			imask &= ~INT_MASK_BUF_READY;
+	}
+
+	spin_lock_irqsave(&host->lock, flags);
+	host->imask = imask;
+	MMC_INT_MASK = host->imask;
+	spin_unlock_irqrestore(&host->lock, flags);
+
+	dev_dbg(mmc_dev(host->mmc), "CMD%02d (0x%02x) mask set to 0x%04x\n",
+		cmd->opcode, cmd->opcode, imask);
+
+	imxmci_start_clock(host);
+}
+
+static void imxmci_finish_request(struct imxmci_host *host, struct mmc_request *req)
+{
+	unsigned long flags;
+
+	spin_lock_irqsave(&host->lock, flags);
+
+	host->pending_events &= ~(IMXMCI_PEND_WAIT_RESP_m | IMXMCI_PEND_DMA_END_m |
+			IMXMCI_PEND_DMA_DATA_m | IMXMCI_PEND_CPU_DATA_m);
+
+	host->imask = IMXMCI_INT_MASK_DEFAULT;
+	MMC_INT_MASK = host->imask;
+
+	spin_unlock_irqrestore(&host->lock, flags);
+
+	host->req = NULL;
+	host->cmd = NULL;
+	host->data = NULL;
+	mmc_request_done(host->mmc, req);
+}
+
+static int imxmci_finish_data(struct imxmci_host *host, unsigned int stat)
+{
+	struct mmc_data *data = host->data;
+	int data_error;
+
+	if(test_and_clear_bit(IMXMCI_PEND_DMA_DATA_b, &host->pending_events)){
+		imx_dma_disable(host->dma);
+		dma_unmap_sg(mmc_dev(host->mmc), data->sg, host->dma_nents,
+			     host->dma_dir);
+	}
+
+	if ( stat & STATUS_ERR_MASK ) {
+		dev_dbg(mmc_dev(host->mmc), "request failed. status: 0x%08x\n",stat);
+		if(stat & (STATUS_CRC_READ_ERR | STATUS_CRC_WRITE_ERR))
+			data->error = MMC_ERR_BADCRC;
+		else if(stat & STATUS_TIME_OUT_READ)
+			data->error = MMC_ERR_TIMEOUT;
+		else
+			data->error = MMC_ERR_FAILED;
+	} else {
+		data->bytes_xfered = host->dma_size;
+	}
+
+	data_error = data->error;
+
+	host->data = NULL;
+
+	return data_error;
+}
+
+static int imxmci_cmd_done(struct imxmci_host *host, unsigned int stat)
+{
+	struct mmc_command *cmd = host->cmd;
+	int i;
+	u32 a,b,c;
+	struct mmc_data *data = host->data;
+
+	if (!cmd)
+		return 0;
+
+	host->cmd = NULL;
+
+	if (stat & STATUS_TIME_OUT_RESP) {
+		dev_dbg(mmc_dev(host->mmc), "CMD TIMEOUT\n");
+		cmd->error = MMC_ERR_TIMEOUT;
+	} else if (stat & STATUS_RESP_CRC_ERR && cmd->flags & MMC_RSP_CRC) {
+		dev_dbg(mmc_dev(host->mmc), "cmd crc error\n");
+		cmd->error = MMC_ERR_BADCRC;
+	}
+
+	if(cmd->flags & MMC_RSP_PRESENT) {
+		if(cmd->flags & MMC_RSP_136) {
+			for (i = 0; i < 4; i++) {
+				u32 a = MMC_RES_FIFO & 0xffff;
+				u32 b = MMC_RES_FIFO & 0xffff;
+				cmd->resp[i] = a<<16 | b;
+			}
+		} else {
+			a = MMC_RES_FIFO & 0xffff;
+			b = MMC_RES_FIFO & 0xffff;
+			c = MMC_RES_FIFO & 0xffff;
+			cmd->resp[0] = a<<24 | b<<8 | c>>8;
+		}
+	}
+
+	dev_dbg(mmc_dev(host->mmc), "RESP 0x%08x, 0x%08x, 0x%08x, 0x%08x, error %d\n",
+		cmd->resp[0], cmd->resp[1], cmd->resp[2], cmd->resp[3], cmd->error);
+
+	if (data && (cmd->error == MMC_ERR_NONE) && !(stat & STATUS_ERR_MASK)) {
+		if (host->req->data->flags & MMC_DATA_WRITE) {
+
+			/* Wait for FIFO to be empty before starting DMA write */
+
+			stat = MMC_STATUS;
+			if(imxmci_busy_wait_for_status(host, &stat,
+				STATUS_APPL_BUFF_FE,
+				40, "imxmci_cmd_done DMA WR") < 0) {
+				cmd->error = MMC_ERR_FIFO;
+				imxmci_finish_data(host, stat);
+				if(host->req)
+					imxmci_finish_request(host, host->req);
+				dev_warn(mmc_dev(host->mmc), "STATUS = 0x%04x\n",
+				       stat);
+				return 0;
+			}
+
+			if(test_bit(IMXMCI_PEND_DMA_DATA_b, &host->pending_events)) {
+				imx_dma_enable(host->dma);
+			}
+		}
+	} else {
+		struct mmc_request *req;
+		imxmci_stop_clock(host);
+		req = host->req;
+
+		if(data)
+			imxmci_finish_data(host, stat);
+
+		if( req ) {
+			imxmci_finish_request(host, req);
+		} else {
+			dev_warn(mmc_dev(host->mmc), "imxmci_cmd_done: no request to finish\n");
+		}
+	}
+
+	return 1;
+}
+
+static int imxmci_data_done(struct imxmci_host *host, unsigned int stat)
+{
+	struct mmc_data *data = host->data;
+	int data_error;
+
+	if (!data)
+		return 0;
+
+	data_error = imxmci_finish_data(host, stat);
+
+	if (host->req->stop && (data_error == MMC_ERR_NONE)) {
+		imxmci_stop_clock(host);
+		imxmci_start_cmd(host, host->req->stop, 0);
+	} else {
+		struct mmc_request *req;
+		req = host->req;
+		if( req ) {
+			imxmci_finish_request(host, req);
+		} else {
+			dev_warn(mmc_dev(host->mmc), "imxmci_data_done: no request to finish\n");
+		}
+	}
+
+	return 1;
+}
+
+static int imxmci_cpu_driven_data(struct imxmci_host *host, unsigned int *pstat)
+{
+	int i;
+	int burst_len;
+	int flush_len;
+	int trans_done = 0;
+	unsigned int stat = *pstat;
+
+	if(host->actual_bus_width == MMC_BUS_WIDTH_4)
+		burst_len = 16;
+	else
+		burst_len = 64;
+
+	/* This is unfortunately required */
+	dev_dbg(mmc_dev(host->mmc), "imxmci_cpu_driven_data running STATUS = 0x%x\n",
+		stat);
+
+	if(host->dma_dir == DMA_FROM_DEVICE) {
+		imxmci_busy_wait_for_status(host, &stat,
+				STATUS_APPL_BUFF_FF | STATUS_DATA_TRANS_DONE,
+				20, "imxmci_cpu_driven_data read");
+
+		while((stat & (STATUS_APPL_BUFF_FF |  STATUS_DATA_TRANS_DONE)) &&
+		      (host->data_cnt < host->dma_size)) {
+			if(burst_len >= host->dma_size - host->data_cnt) {
+				flush_len = burst_len;
+				burst_len = host->dma_size - host->data_cnt;
+				flush_len -= burst_len;
+				host->data_cnt = host->dma_size;
+				trans_done = 1;
+			} else {
+				flush_len = 0;
+				host->data_cnt += burst_len;
+			}
+
+			for(i = burst_len; i>=2 ; i-=2) {
+				*(host->data_ptr++) = MMC_BUFFER_ACCESS;
+				udelay(20);	/* required for clocks < 8MHz*/
+			}
+
+			if(i == 1)
+				*(u8*)(host->data_ptr) = MMC_BUFFER_ACCESS;
+
+			stat = MMC_STATUS;
+
+			/* Flush extra bytes from FIFO */
+			while(flush_len >= 2){
+				flush_len -= 2;
+				i = MMC_BUFFER_ACCESS;
+				stat = MMC_STATUS;
+				stat &= ~STATUS_CRC_READ_ERR; /* Stupid but required there */
+			}
+
+			dev_dbg(mmc_dev(host->mmc), "imxmci_cpu_driven_data read burst %d STATUS = 0x%x\n",
+				burst_len, stat);
+		}
+	} else {
+		imxmci_busy_wait_for_status(host, &stat,
+				STATUS_APPL_BUFF_FE,
+				20, "imxmci_cpu_driven_data write");
+
+		while((stat & STATUS_APPL_BUFF_FE) &&
+		      (host->data_cnt < host->dma_size)) {
+			if(burst_len >= host->dma_size - host->data_cnt) {
+				burst_len = host->dma_size - host->data_cnt;
+				host->data_cnt = host->dma_size;
+				trans_done = 1;
+			} else {
+				host->data_cnt += burst_len;
+			}
+
+			for(i = burst_len; i>0 ; i-=2)
+				MMC_BUFFER_ACCESS = *(host->data_ptr++);
+
+			stat = MMC_STATUS;
+
+			dev_dbg(mmc_dev(host->mmc), "imxmci_cpu_driven_data write burst %d STATUS = 0x%x\n",
+				burst_len, stat);
+		}
+	}
+
+	*pstat = stat;
+
+	return trans_done;
+}
+
+static void imxmci_dma_irq(int dma, void *devid, struct pt_regs *regs)
+{
+	struct imxmci_host *host = devid;
+	uint32_t stat = MMC_STATUS;
+
+	atomic_set(&host->stuck_timeout, 0);
+	host->status_reg = stat;
+	set_bit(IMXMCI_PEND_DMA_END_b, &host->pending_events);
+	tasklet_schedule(&host->tasklet);
+}
+
+static irqreturn_t imxmci_irq(int irq, void *devid, struct pt_regs *regs)
+{
+	struct imxmci_host *host = devid;
+	uint32_t stat = MMC_STATUS;
+	int handled = 1;
+
+	MMC_INT_MASK = host->imask | INT_MASK_SDIO | INT_MASK_AUTO_CARD_DETECT;
+
+	atomic_set(&host->stuck_timeout, 0);
+	host->status_reg = stat;
+	set_bit(IMXMCI_PEND_IRQ_b, &host->pending_events);
+	tasklet_schedule(&host->tasklet);
+
+	return IRQ_RETVAL(handled);;
+}
+
+static void imxmci_tasklet_fnc(unsigned long data)
+{
+	struct imxmci_host *host = (struct imxmci_host *)data;
+	u32 stat;
+	unsigned int data_dir_mask = 0;	/* STATUS_WR_CRC_ERROR_CODE_MASK */
+	int timeout = 0;
+
+	if(atomic_read(&host->stuck_timeout) > 4) {
+		char *what;
+		timeout = 1;
+		stat = MMC_STATUS;
+		host->status_reg = stat;
+		if (test_bit(IMXMCI_PEND_WAIT_RESP_b, &host->pending_events))
+			if (test_bit(IMXMCI_PEND_DMA_DATA_b, &host->pending_events))
+				what = "RESP+DMA";
+			else
+				what = "RESP";
+		else
+			if (test_bit(IMXMCI_PEND_DMA_DATA_b, &host->pending_events))
+				if(test_bit(IMXMCI_PEND_DMA_END_b, &host->pending_events))
+					what = "DATA";
+				else
+					what = "DMA";
+			else
+				what = "???";
+
+		dev_err(mmc_dev(host->mmc), "%s TIMEOUT, hardware stucked STATUS = 0x%04x IMASK = 0x%04x\n",
+		       what, stat, MMC_INT_MASK);
+		dev_err(mmc_dev(host->mmc), "CMD_DAT_CONT = 0x%04x, MMC_BLK_LEN = 0x%04x, MMC_NOB = 0x%04x, DMA_CCR = 0x%08x\n",
+		       MMC_CMD_DAT_CONT, MMC_BLK_LEN, MMC_NOB, CCR(host->dma));
+		dev_err(mmc_dev(host->mmc), "CMD%d, bus %d-bit, dma_size = 0x%x\n",
+		       host->cmd?host->cmd->opcode:0, 1<<host->actual_bus_width, host->dma_size);
+	}
+
+	if(!host->present || timeout)
+		host->status_reg = STATUS_TIME_OUT_RESP | STATUS_TIME_OUT_READ |
+				    STATUS_CRC_READ_ERR | STATUS_CRC_WRITE_ERR;
+
+	if(test_bit(IMXMCI_PEND_IRQ_b, &host->pending_events) || timeout) {
+		clear_bit(IMXMCI_PEND_IRQ_b, &host->pending_events);
+
+		stat = MMC_STATUS;
+		/*
+		 * This is not required in theory, but there is chance to miss some flag
+		 * which clears automatically by mask write, FreeScale original code keeps
+		 * stat from IRQ time so do I
+		 */
+		stat |= host->status_reg;
+
+		if(test_bit(IMXMCI_PEND_WAIT_RESP_b, &host->pending_events)) {
+			imxmci_busy_wait_for_status(host, &stat,
+					STATUS_END_CMD_RESP | STATUS_ERR_MASK,
+					20, "imxmci_tasklet_fnc resp (ERRATUM #4)");
+		}
+
+		if(stat & (STATUS_END_CMD_RESP | STATUS_ERR_MASK)) {
+			if(test_and_clear_bit(IMXMCI_PEND_WAIT_RESP_b, &host->pending_events))
+				imxmci_cmd_done(host, stat);
+			if(host->data && (stat & STATUS_ERR_MASK))
+				imxmci_data_done(host, stat);
+		}
+
+		if(test_bit(IMXMCI_PEND_CPU_DATA_b, &host->pending_events)) {
+			stat |= MMC_STATUS;
+			if(imxmci_cpu_driven_data(host, &stat)){
+				if(test_and_clear_bit(IMXMCI_PEND_WAIT_RESP_b, &host->pending_events))
+					imxmci_cmd_done(host, stat);
+				atomic_clear_mask(IMXMCI_PEND_IRQ_m|IMXMCI_PEND_CPU_DATA_m,
+							&host->pending_events);
+				imxmci_data_done(host, stat);
+			}
+		}
+	}
+
+	if(test_bit(IMXMCI_PEND_DMA_END_b, &host->pending_events) &&
+	   !test_bit(IMXMCI_PEND_WAIT_RESP_b, &host->pending_events)) {
+
+		stat = MMC_STATUS;
+		/* Same as above */
+		stat |= host->status_reg;
+
+		if(host->dma_dir == DMA_TO_DEVICE) {
+			data_dir_mask = STATUS_WRITE_OP_DONE;
+		} else {
+			data_dir_mask = STATUS_DATA_TRANS_DONE;
+		}
+
+		imxmci_busy_wait_for_status(host, &stat,
+				data_dir_mask,
+				50, "imxmci_tasklet_fnc data");
+
+		if(stat & data_dir_mask) {
+			clear_bit(IMXMCI_PEND_DMA_END_b, &host->pending_events);
+			imxmci_data_done(host, stat);
+		}
+	}
+
+	if(test_and_clear_bit(IMXMCI_PEND_CARD_XCHG_b, &host->pending_events)) {
+
+		if(host->cmd)
+			imxmci_cmd_done(host, STATUS_TIME_OUT_RESP);
+
+		if(host->data)
+			imxmci_data_done(host, STATUS_TIME_OUT_READ |
+					 STATUS_CRC_READ_ERR | STATUS_CRC_WRITE_ERR);
+
+		if(host->req)
+			imxmci_finish_request(host, host->req);
+
+		mmc_detect_change(host->mmc, msecs_to_jiffies(100));
+
+	}
+}
+
+static void imxmci_request(struct mmc_host *mmc, struct mmc_request *req)
+{
+	struct imxmci_host *host = mmc_priv(mmc);
+	unsigned int cmdat;
+
+	WARN_ON(host->req != NULL);
+
+	host->req = req;
+
+	cmdat = 0;
+
+	if (req->data) {
+		imxmci_setup_data(host, req->data);
+
+		cmdat |= CMD_DAT_CONT_DATA_ENABLE;
+
+		if (req->data->flags & MMC_DATA_WRITE)
+			cmdat |= CMD_DAT_CONT_WRITE;
+
+		if (req->data->flags & MMC_DATA_STREAM) {
+			cmdat |= CMD_DAT_CONT_STREAM_BLOCK;
+		}
+	}
+
+	imxmci_start_cmd(host, req->cmd, cmdat);
+}
+
+#define CLK_RATE 19200000
+
+static void imxmci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
+{
+	struct imxmci_host *host = mmc_priv(mmc);
+	int prescaler;
+
+	dev_dbg(mmc_dev(host->mmc), "clock %u power %u vdd %u width %u\n",
+		ios->clock, ios->power_mode, ios->vdd,
+		(ios->bus_width==MMC_BUS_WIDTH_4)?4:1);
+
+	if( ios->bus_width==MMC_BUS_WIDTH_4 ) {
+		host->actual_bus_width = MMC_BUS_WIDTH_4;
+		imx_gpio_mode(PB11_PF_SD_DAT3);
+	}else{
+		host->actual_bus_width = MMC_BUS_WIDTH_1;
+		imx_gpio_mode(GPIO_PORTB | GPIO_IN | GPIO_PUEN | 11);
+	}
+
+	if ( host->power_mode != ios->power_mode ) {
+		switch (ios->power_mode) {
+		case MMC_POWER_OFF:
+        		break;
+		case MMC_POWER_UP:
+			set_bit(IMXMCI_PEND_SET_INIT_b, &host->pending_events);
+        		break;
+		case MMC_POWER_ON:
+        		break;
+		}
+		host->power_mode = ios->power_mode;
+	}
+
+	if ( ios->clock ) {
+		unsigned int clk;
+
+		/* The prescaler is 5 for PERCLK2 equal to 96MHz
+		 * then 96MHz / 5 = 19.2 MHz
+		 */
+		clk=imx_get_perclk2();
+		prescaler=(clk+(CLK_RATE*7)/8)/CLK_RATE;
+		switch(prescaler) {
+		case 0:
+		case 1:	prescaler = 0;
+			break;
+		case 2:	prescaler = 1;
+			break;
+		case 3:	prescaler = 2;
+			break;
+		case 4:	prescaler = 4;
+			break;
+		default:
+		case 5:	prescaler = 5;
+			break;
+		}
+
+		dev_dbg(mmc_dev(host->mmc), "PERCLK2 %d MHz -> prescaler %d\n",
+			clk, prescaler);
+
+		for(clk=0; clk<8; clk++) {
+			int x;
+			x = CLK_RATE / (1<<clk);
+			if( x <= ios->clock)
+				break;
+		}
+
+		MMC_STR_STP_CLK |= STR_STP_CLK_ENABLE; /* enable controller */
+
+		imxmci_stop_clock(host);
+		MMC_CLK_RATE = (prescaler<<3) | clk;
+		imxmci_start_clock(host);
+
+		dev_dbg(mmc_dev(host->mmc), "MMC_CLK_RATE: 0x%08x\n", MMC_CLK_RATE);
+	} else {
+		imxmci_stop_clock(host);
+	}
+}
+
+static struct mmc_host_ops imxmci_ops = {
+	.request	= imxmci_request,
+	.set_ios	= imxmci_set_ios,
+};
+
+static struct resource *platform_device_resource(struct platform_device *dev, unsigned int mask, int nr)
+{
+	int i;
+
+	for (i = 0; i < dev->num_resources; i++)
+		if (dev->resource[i].flags == mask && nr-- == 0)
+			return &dev->resource[i];
+	return NULL;
+}
+
+static int platform_device_irq(struct platform_device *dev, int nr)
+{
+	int i;
+
+	for (i = 0; i < dev->num_resources; i++)
+		if (dev->resource[i].flags == IORESOURCE_IRQ && nr-- == 0)
+			return dev->resource[i].start;
+	return NO_IRQ;
+}
+
+static void imxmci_check_status(unsigned long data)
+{
+	struct imxmci_host *host = (struct imxmci_host *)data;
+
+	if( host->pdata->card_present() != host->present ) {
+		host->present ^= 1;
+		dev_info(mmc_dev(host->mmc), "card %s\n",
+		      host->present ? "inserted" : "removed");
+
+		set_bit(IMXMCI_PEND_CARD_XCHG_b, &host->pending_events);
+		tasklet_schedule(&host->tasklet);
+	}
+
+	if(test_bit(IMXMCI_PEND_WAIT_RESP_b, &host->pending_events) ||
+	   test_bit(IMXMCI_PEND_DMA_DATA_b, &host->pending_events)) {
+		atomic_inc(&host->stuck_timeout);
+		if(atomic_read(&host->stuck_timeout) > 4)
+			tasklet_schedule(&host->tasklet);
+	} else {
+		atomic_set(&host->stuck_timeout, 0);
+
+	}
+
+	mod_timer(&host->timer, jiffies + (HZ>>1));
+}
+
+static int imxmci_probe(struct platform_device *pdev)
+{
+	struct mmc_host *mmc;
+	struct imxmci_host *host = NULL;
+	struct resource *r;
+	int ret = 0, irq;
+
+	printk(KERN_INFO "i.MX mmc driver\n");
+
+	r = platform_device_resource(pdev, IORESOURCE_MEM, 0);
+	irq = platform_device_irq(pdev, 0);
+	if (!r || irq == NO_IRQ)
+		return -ENXIO;
+
+	r = request_mem_region(r->start, 0x100, "IMXMCI");
+	if (!r)
+		return -EBUSY;
+
+	mmc = mmc_alloc_host(sizeof(struct imxmci_host), &pdev->dev);
+	if (!mmc) {
+		ret = -ENOMEM;
+		goto out;
+	}
+
+	mmc->ops = &imxmci_ops;
+	mmc->f_min = 150000;
+	mmc->f_max = CLK_RATE/2;
+	mmc->ocr_avail = MMC_VDD_32_33;
+	mmc->caps |= MMC_CAP_4_BIT_DATA;
+
+	/* MMC core transfer sizes tunable parameters */
+	mmc->max_hw_segs = 64;
+	mmc->max_phys_segs = 64;
+	mmc->max_sectors = 64;		/* default 1 << (PAGE_CACHE_SHIFT - 9) */
+	mmc->max_seg_size = 64*512;	/* default PAGE_CACHE_SIZE */
+
+	host = mmc_priv(mmc);
+	host->mmc = mmc;
+	host->dma_allocated = 0;
+	host->pdata = pdev->dev.platform_data;
+
+	spin_lock_init(&host->lock);
+	host->res = r;
+	host->irq = irq;
+
+	imx_gpio_mode(PB8_PF_SD_DAT0);
+	imx_gpio_mode(PB9_PF_SD_DAT1);
+	imx_gpio_mode(PB10_PF_SD_DAT2);
+	/* Configured as GPIO with pull-up to ensure right MCC card mode */
+	/* Switched to PB11_PF_SD_DAT3 if 4 bit bus is configured */
+	imx_gpio_mode(GPIO_PORTB | GPIO_IN | GPIO_PUEN | 11);
+	/* imx_gpio_mode(PB11_PF_SD_DAT3); */
+	imx_gpio_mode(PB12_PF_SD_CLK);
+	imx_gpio_mode(PB13_PF_SD_CMD);
+
+	imxmci_softreset();
+
+	if ( MMC_REV_NO != 0x390 ) {
+		dev_err(mmc_dev(host->mmc), "wrong rev.no. 0x%08x. aborting.\n",
+		        MMC_REV_NO);
+		goto out;
+	}
+
+	MMC_READ_TO = 0x2db4; /* recommended in data sheet */
+
+	host->imask = IMXMCI_INT_MASK_DEFAULT;
+	MMC_INT_MASK = host->imask;
+
+
+	if(imx_dma_request_by_prio(&host->dma, DRIVER_NAME, DMA_PRIO_LOW)<0){
+		dev_err(mmc_dev(host->mmc), "imx_dma_request_by_prio failed\n");
+		ret = -EBUSY;
+		goto out;
+	}
+	host->dma_allocated=1;
+	imx_dma_setup_handlers(host->dma, imxmci_dma_irq, NULL, host);
+
+	tasklet_init(&host->tasklet, imxmci_tasklet_fnc, (unsigned long)host);
+	host->status_reg=0;
+	host->pending_events=0;
+
+	ret = request_irq(host->irq, imxmci_irq, 0, DRIVER_NAME, host);
+	if (ret)
+		goto out;
+
+	host->present = host->pdata->card_present();
+	init_timer(&host->timer);
+	host->timer.data = (unsigned long)host;
+	host->timer.function = imxmci_check_status;
+	add_timer(&host->timer);
+	mod_timer(&host->timer, jiffies + (HZ>>1));
+
+	platform_set_drvdata(pdev, mmc);
+
+	mmc_add_host(mmc);
+
+	return 0;
+
+out:
+	if (host) {
+		if(host->dma_allocated){
+			imx_dma_free(host->dma);
+			host->dma_allocated=0;
+		}
+	}
+	if (mmc)
+		mmc_free_host(mmc);
+	release_resource(r);
+	return ret;
+}
+
+static int imxmci_remove(struct platform_device *pdev)
+{
+	struct mmc_host *mmc = platform_get_drvdata(pdev);
+
+	platform_set_drvdata(pdev, NULL);
+
+	if (mmc) {
+		struct imxmci_host *host = mmc_priv(mmc);
+
+		tasklet_disable(&host->tasklet);
+
+		del_timer_sync(&host->timer);
+		mmc_remove_host(mmc);
+
+		free_irq(host->irq, host);
+		if(host->dma_allocated){
+			imx_dma_free(host->dma);
+			host->dma_allocated=0;
+		}
+
+		tasklet_kill(&host->tasklet);
+
+		release_resource(host->res);
+
+		mmc_free_host(mmc);
+	}
+	return 0;
+}
+
+#ifdef CONFIG_PM
+static int imxmci_suspend(struct platform_device *dev, pm_message_t state)
+{
+	struct mmc_host *mmc = platform_get_drvdata(dev);
+	int ret = 0;
+
+	if (mmc)
+		ret = mmc_suspend_host(mmc, state);
+
+	return ret;
+}
+
+static int imxmci_resume(struct platform_device *dev)
+{
+	struct mmc_host *mmc = platform_get_drvdata(dev);
+	struct imxmci_host *host;
+	int ret = 0;
+
+	if (mmc) {
+		host = mmc_priv(mmc);
+		if(host)
+			set_bit(IMXMCI_PEND_SET_INIT_b, &host->pending_events);
+		ret = mmc_resume_host(mmc);
+	}
+
+	return ret;
+}
+#else
+#define imxmci_suspend  NULL
+#define imxmci_resume   NULL
+#endif /* CONFIG_PM */
+
+static struct platform_driver imxmci_driver = {
+	.probe		= imxmci_probe,
+	.remove		= imxmci_remove,
+	.suspend	= imxmci_suspend,
+	.resume		= imxmci_resume,
+	.driver		= {
+		.name		= DRIVER_NAME,
+	}
+};
+
+static int __init imxmci_init(void)
+{
+	return platform_driver_register(&imxmci_driver);
+}
+
+static void __exit imxmci_exit(void)
+{
+	platform_driver_unregister(&imxmci_driver);
+}
+
+module_init(imxmci_init);
+module_exit(imxmci_exit);
+
+MODULE_DESCRIPTION("i.MX Multimedia Card Interface Driver");
+MODULE_AUTHOR("Sascha Hauer, Pengutronix");
+MODULE_LICENSE("GPL");
diff --git a/drivers/mmc/imxmmc.h b/drivers/mmc/imxmmc.h
new file mode 100644
index 0000000..e5339e3
--- /dev/null
+++ b/drivers/mmc/imxmmc.h
@@ -0,0 +1,67 @@
+
+# define __REG16(x)	(*((volatile u16 *)IO_ADDRESS(x)))
+
+#define MMC_STR_STP_CLK  __REG16(IMX_MMC_BASE + 0x00)
+#define MMC_STATUS       __REG16(IMX_MMC_BASE + 0x04)
+#define MMC_CLK_RATE     __REG16(IMX_MMC_BASE + 0x08)
+#define MMC_CMD_DAT_CONT __REG16(IMX_MMC_BASE + 0x0C)
+#define MMC_RES_TO       __REG16(IMX_MMC_BASE + 0x10)
+#define MMC_READ_TO      __REG16(IMX_MMC_BASE + 0x14)
+#define MMC_BLK_LEN      __REG16(IMX_MMC_BASE + 0x18)
+#define MMC_NOB          __REG16(IMX_MMC_BASE + 0x1C)
+#define MMC_REV_NO       __REG16(IMX_MMC_BASE + 0x20)
+#define MMC_INT_MASK     __REG16(IMX_MMC_BASE + 0x24)
+#define MMC_CMD          __REG16(IMX_MMC_BASE + 0x28)
+#define MMC_ARGH         __REG16(IMX_MMC_BASE + 0x2C)
+#define MMC_ARGL         __REG16(IMX_MMC_BASE + 0x30)
+#define MMC_RES_FIFO     __REG16(IMX_MMC_BASE + 0x34)
+#define MMC_BUFFER_ACCESS __REG16(IMX_MMC_BASE + 0x38)
+#define MMC_BUFFER_ACCESS_OFS 0x38
+
+
+#define STR_STP_CLK_ENDIAN              (1<<5)
+#define STR_STP_CLK_RESET               (1<<3)
+#define STR_STP_CLK_ENABLE              (1<<2)
+#define STR_STP_CLK_START_CLK           (1<<1)
+#define STR_STP_CLK_STOP_CLK            (1<<0)
+#define STATUS_CARD_PRESENCE            (1<<15)
+#define STATUS_SDIO_INT_ACTIVE          (1<<14)
+#define STATUS_END_CMD_RESP             (1<<13)
+#define STATUS_WRITE_OP_DONE            (1<<12)
+#define STATUS_DATA_TRANS_DONE          (1<<11)
+#define STATUS_WR_CRC_ERROR_CODE_MASK   (3<<10)
+#define STATUS_CARD_BUS_CLK_RUN         (1<<8)
+#define STATUS_APPL_BUFF_FF             (1<<7)
+#define STATUS_APPL_BUFF_FE             (1<<6)
+#define STATUS_RESP_CRC_ERR             (1<<5)
+#define STATUS_CRC_READ_ERR             (1<<3)
+#define STATUS_CRC_WRITE_ERR            (1<<2)
+#define STATUS_TIME_OUT_RESP            (1<<1)
+#define STATUS_TIME_OUT_READ            (1<<0)
+#define STATUS_ERR_MASK                 0x2f
+#define CLK_RATE_PRESCALER(x)           ((x) & 0x7)
+#define CLK_RATE_CLK_RATE(x)            (((x) & 0x7) << 3)
+#define CMD_DAT_CONT_CMD_RESP_LONG_OFF  (1<<12)
+#define CMD_DAT_CONT_STOP_READWAIT      (1<<11)
+#define CMD_DAT_CONT_START_READWAIT     (1<<10)
+#define CMD_DAT_CONT_BUS_WIDTH_1        (0<<8)
+#define CMD_DAT_CONT_BUS_WIDTH_4        (2<<8)
+#define CMD_DAT_CONT_INIT               (1<<7)
+#define CMD_DAT_CONT_BUSY               (1<<6)
+#define CMD_DAT_CONT_STREAM_BLOCK       (1<<5)
+#define CMD_DAT_CONT_WRITE              (1<<4)
+#define CMD_DAT_CONT_DATA_ENABLE        (1<<3)
+#define CMD_DAT_CONT_RESPONSE_FORMAT_R1 (1)
+#define CMD_DAT_CONT_RESPONSE_FORMAT_R2 (2)
+#define CMD_DAT_CONT_RESPONSE_FORMAT_R3 (3)
+#define CMD_DAT_CONT_RESPONSE_FORMAT_R4 (4)
+#define CMD_DAT_CONT_RESPONSE_FORMAT_R5 (5)
+#define CMD_DAT_CONT_RESPONSE_FORMAT_R6 (6)
+#define INT_MASK_AUTO_CARD_DETECT       (1<<6)
+#define INT_MASK_DAT0_EN                (1<<5)
+#define INT_MASK_SDIO                   (1<<4)
+#define INT_MASK_BUF_READY              (1<<3)
+#define INT_MASK_END_CMD_RES            (1<<2)
+#define INT_MASK_WRITE_OP_DONE          (1<<1)
+#define INT_MASK_DATA_TRAN              (1<<0)
+#define INT_ALL                         (0x7f)
diff --git a/include/asm-arm/arch-at91rm9200/at91rm9200_mci.h b/include/asm-arm/arch-at91rm9200/at91rm9200_mci.h
new file mode 100644
index 0000000..f28636d
--- /dev/null
+++ b/include/asm-arm/arch-at91rm9200/at91rm9200_mci.h
@@ -0,0 +1,104 @@
+/*
+ * include/asm-arm/arch-at91rm9200/at91rm9200_mci.h
+ *
+ * Copyright (C) 2005 Ivan Kokshaysky
+ * Copyright (C) SAN People
+ *
+ * MultiMedia Card Interface (MCI) registers.
+ * Based on AT91RM9200 datasheet revision E.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#ifndef AT91RM9200_MCI_H
+#define AT91RM9200_MCI_H
+
+#define AT91_MCI_CR		0x00		/* Control Register */
+#define		AT91_MCI_MCIEN		(1 <<  0)	/* Multi-Media Interface Enable */
+#define		AT91_MCI_MCIDIS		(1 <<  1)	/* Multi-Media Interface Disable */
+#define		AT91_MCI_PWSEN		(1 <<  2)	/* Power Save Mode Enable */
+#define		AT91_MCI_PWSDIS		(1 <<  3)	/* Power Save Mode Disable */
+#define		AT91_MCI_SWRST		(1 <<  7)	/* Software Reset */
+
+#define AT91_MCI_MR		0x04		/* Mode Register */
+#define		AT91_MCI_CLKDIV		(0xff  <<  0)	/* Clock Divider */
+#define		AT91_MCI_PWSDIV		(3     <<  8)	/* Power Saving Divider */
+#define		AT91_MCI_PDCPADV	(1     << 14)	/* PDC Padding Value */
+#define		AT91_MCI_PDCMODE	(1     << 15)	/* PDC-orientated Mode */
+#define		AT91_MCI_BLKLEN 	(0xfff << 18)	/* Data Block Length */
+
+#define AT91_MCI_DTOR		0x08		/* Data Timeout Register */
+#define		AT91_MCI_DTOCYC		(0xf << 0)	/* Data Timeout Cycle Number */
+#define		AT91_MCI_DTOMUL		(7   << 4)	/* Data Timeout Multiplier */
+#define		AT91_MCI_DTOMUL_1		(0 <<  4)
+#define		AT91_MCI_DTOMUL_16		(1 <<  4)
+#define		AT91_MCI_DTOMUL_128		(2 <<  4)
+#define		AT91_MCI_DTOMUL_256		(3 <<  4)
+#define		AT91_MCI_DTOMUL_1K		(4 <<  4)
+#define		AT91_MCI_DTOMUL_4K		(5 <<  4)
+#define		AT91_MCI_DTOMUL_64K		(6 <<  4)
+#define		AT91_MCI_DTOMUL_1M		(7 <<  4)
+
+#define AT91_MCI_SDCR		0x0c		/* SD Card Register */
+#define		AT91_MCI_SDCSEL		(0xf << 0)	/* SD Card Selector */
+#define		AT91_MCI_SDCBUS		(1   << 7)	/* 1-bit or 4-bit bus */
+
+#define AT91_MCI_ARGR		0x10		/* Argument Register */
+
+#define AT91_MCI_CMDR		0x14		/* Command Register */
+#define		AT91_MCI_CMDNB		(0x3f << 0)	/* Command Number */
+#define		AT91_MCI_RSPTYP		(3    << 6)	/* Response Type */
+#define			AT91_MCI_RSPTYP_NONE	(0 <<  6)
+#define			AT91_MCI_RSPTYP_48	(1 <<  6)
+#define			AT91_MCI_RSPTYP_136	(2 <<  6)
+#define		AT91_MCI_SPCMD		(7    << 8)	/* Special Command */
+#define			AT91_MCI_SPCMD_NONE	(0 <<  8)
+#define			AT91_MCI_SPCMD_INIT	(1 <<  8)
+#define			AT91_MCI_SPCMD_SYNC	(2 <<  8)
+#define			AT91_MCI_SPCMD_ICMD	(4 <<  8)
+#define			AT91_MCI_SPCMD_IRESP	(5 <<  8)
+#define		AT91_MCI_OPDCMD		(1 << 11)	/* Open Drain Command */
+#define		AT91_MCI_MAXLAT		(1 << 12)	/* Max Latency for Command to Response */
+#define		AT91_MCI_TRCMD		(3 << 16)	/* Transfer Command */
+#define			AT91_MCI_TRCMD_NONE	(0 << 16)
+#define			AT91_MCI_TRCMD_START	(1 << 16)
+#define			AT91_MCI_TRCMD_STOP	(2 << 16)
+#define		AT91_MCI_TRDIR		(1 << 18)	/* Transfer Direction */
+#define		AT91_MCI_TRTYP		(3 << 19)	/* Transfer Type */
+#define			AT91_MCI_TRTYP_BLOCK	(0 << 19)
+#define			AT91_MCI_TRTYP_MULTIPLE	(1 << 19)
+#define			AT91_MCI_TRTYP_STREAM	(2 << 19)
+
+#define AT91_MCI_RSPR(n)	(0x20 + ((n) * 4))	/* Response Registers 0-3 */
+#define AT91_MCR_RDR		0x30		/* Receive Data Register */
+#define AT91_MCR_TDR		0x34		/* Transmit Data Register */
+
+#define AT91_MCI_SR		0x40		/* Status Register */
+#define		AT91_MCI_CMDRDY		(1 <<  0)	/* Command Ready */
+#define		AT91_MCI_RXRDY		(1 <<  1) 	/* Receiver Ready */
+#define		AT91_MCI_TXRDY		(1 <<  2)	/* Transmit Ready */
+#define		AT91_MCI_BLKE		(1 <<  3)	/* Data Block Ended */
+#define		AT91_MCI_DTIP		(1 <<  4)	/* Data Transfer in Progress */
+#define		AT91_MCI_NOTBUSY	(1 <<  5)	/* Data Not Busy */
+#define		AT91_MCI_ENDRX		(1 <<  6)	/* End of RX Buffer */
+#define		AT91_MCI_ENDTX		(1 <<  7)	/* End fo TX Buffer */
+#define		AT91_MCI_RXBUFF		(1 << 14)	/* RX Buffer Full */
+#define		AT91_MCI_TXBUFE		(1 << 15)	/* TX Buffer Empty */
+#define		AT91_MCI_RINDE		(1 << 16)  	/* Response Index Error */
+#define		AT91_MCI_RDIRE		(1 << 17)	/* Response Direction Error */
+#define		AT91_MCI_RCRCE		(1 << 18)   	/* Response CRC Error */
+#define		AT91_MCI_RENDE		(1 << 19)	/* Response End Bit Error */
+#define		AT91_MCI_RTOE		(1 << 20)	/* Reponse Time-out Error */
+#define		AT91_MCI_DCRCE		(1 << 21)	/* Data CRC Error */
+#define		AT91_MCI_DTOE		(1 << 22)	/* Data Time-out Error */
+#define		AT91_MCI_OVRE		(1 << 30)	/* Overrun */
+#define		AT91_MCI_UNRE		(1 << 31)	/* Underrun */
+
+#define AT91_MCI_IER		0x44		/* Interrupt Enable Register */
+#define AT91_MCI_IDR		0x48		/* Interrupt Disable Register */
+#define AT91_MCI_IMR		0x4c		/* Interrupt Mask Register */
+
+#endif
diff --git a/include/asm-arm/arch-imx/mmc.h b/include/asm-arm/arch-imx/mmc.h
new file mode 100644
index 0000000..1937151
--- /dev/null
+++ b/include/asm-arm/arch-imx/mmc.h
@@ -0,0 +1,12 @@
+#ifndef ASMARM_ARCH_MMC_H
+#define ASMARM_ARCH_MMC_H
+
+#include <linux/mmc/protocol.h>
+
+struct imxmmc_platform_data {
+	int (*card_present)(void);
+};
+
+extern void imx_set_mmc_info(struct imxmmc_platform_data *info);
+
+#endif