Merge tag 'v4.1-legacy' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup

Merge "omap legacy boot clean-up for v4.1" from Tony Lindgren:

Drop three omap3 legacy board-*.c files

We want to get omap3 moved over to device tree only based booting.

These three board-*.c files seem to be inactive, so let's attempt
to drop them now rather than later. With these dropped, we have
omap3 device tree conversion status in a known state. Then we know
that we have .dts support for the remaining omap3 board-*.c files,
or it's being worked on.

By dropping these files now, we can simply revert them if really
needed for the next few merge cycles if we run into suprises.
Reverting things later on will not be so easily done.

* tag 'v4.1-legacy' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: OMAP2+: Remove legacy support for omap3 TouchBook
  ARM: OMAP3: Remove legacy support for devkit8000
  ARM: OMAP3: Remove legacy support for EMA-Tech Stalker board

Signed-off-by: Olof Johansson <olof@lixom.net>

5 files changed, 0 insertions, 1504 deletions

diff --git a/arch/arm/mach-omap2/Kconfig b/arch/arm/mach-omap2/Kconfig
index 2b8e477..276a755 100644
--- a/arch/arm/mach-omap2/Kconfig
+++ b/arch/arm/mach-omap2/Kconfig
@@ -175,12 +175,6 @@ config MACH_OMAP3_BEAGLE
 	default y
 	select OMAP_PACKAGE_CBB
 
-config MACH_DEVKIT8000
-	bool "DEVKIT8000 board"
-	depends on ARCH_OMAP3
-	default y
-	select OMAP_PACKAGE_CUS
-
 config MACH_OMAP_LDP
 	bool "OMAP3 LDP board"
 	depends on ARCH_OMAP3
@@ -225,12 +219,6 @@ config MACH_OMAP3_PANDORA
 	select OMAP_PACKAGE_CBB
 	select REGULATOR_FIXED_VOLTAGE if REGULATOR
 
-config MACH_TOUCHBOOK
-	bool "OMAP3 Touch Book"
-	depends on ARCH_OMAP3
-	default y
-	select OMAP_PACKAGE_CBB
-
 config MACH_NOKIA_N810
        bool
 
@@ -260,12 +248,6 @@ config MACH_CM_T35
 config MACH_CM_T3730
        bool
 
-config MACH_SBC3530
-	bool "OMAP3 SBC STALKER board"
-	depends on ARCH_OMAP3
-	default y
-	select OMAP_PACKAGE_CUS
-
 config OMAP3_SDRC_AC_TIMING
 	bool "Enable SDRC AC timing register changes"
 	depends on ARCH_OMAP3
diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile
index b83f18f..ec002bd 100644
--- a/arch/arm/mach-omap2/Makefile
+++ b/arch/arm/mach-omap2/Makefile
@@ -243,7 +243,6 @@ obj-$(CONFIG_SOC_OMAP2420)		+= msdi.o
 # Specific board support
 obj-$(CONFIG_MACH_OMAP_GENERIC)		+= board-generic.o pdata-quirks.o
 obj-$(CONFIG_MACH_OMAP3_BEAGLE)		+= board-omap3beagle.o
-obj-$(CONFIG_MACH_DEVKIT8000)     	+= board-devkit8000.o
 obj-$(CONFIG_MACH_OMAP_LDP)		+= board-ldp.o
 obj-$(CONFIG_MACH_OMAP3530_LV_SOM)      += board-omap3logic.o
 obj-$(CONFIG_MACH_OMAP3_TORPEDO)        += board-omap3logic.o
@@ -254,9 +253,6 @@ obj-$(CONFIG_MACH_NOKIA_RX51)		+= board-rx51.o sdram-nokia.o
 obj-$(CONFIG_MACH_NOKIA_RX51)		+= board-rx51-peripherals.o
 obj-$(CONFIG_MACH_NOKIA_RX51)		+= board-rx51-video.o
 obj-$(CONFIG_MACH_CM_T35)		+= board-cm-t35.o
-obj-$(CONFIG_MACH_TOUCHBOOK)		+= board-omap3touchbook.o
-
-obj-$(CONFIG_MACH_SBC3530)		+= board-omap3stalker.o
 
 # Platform specific device init code
 
diff --git a/arch/arm/mach-omap2/board-devkit8000.c b/arch/arm/mach-omap2/board-devkit8000.c
deleted file mode 100644
index d8e4f34..0000000
--- a/arch/arm/mach-omap2/board-devkit8000.c
+++ /dev/null
@@ -1,654 +0,0 @@
-/*
- * board-devkit8000.c - TimLL Devkit8000
- *
- * Copyright (C) 2009 Kim Botherway
- * Copyright (C) 2010 Thomas Weber
- *
- * Modified from mach-omap2/board-omap3beagle.c
- *
- * Initial code: Syed Mohammed Khasim
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/delay.h>
-#include <linux/err.h>
-#include <linux/clk.h>
-#include <linux/io.h>
-#include <linux/leds.h>
-#include <linux/gpio.h>
-#include <linux/input.h>
-#include <linux/gpio_keys.h>
-
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/partitions.h>
-#include <linux/mtd/nand.h>
-#include <linux/mmc/host.h>
-#include <linux/usb/phy.h>
-
-#include <linux/regulator/machine.h>
-#include <linux/i2c/twl.h>
-#include "id.h"
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <asm/mach/flash.h>
-
-#include "common.h"
-#include "gpmc.h"
-#include <linux/platform_data/mtd-nand-omap2.h>
-#include <video/omapdss.h>
-#include <video/omap-panel-data.h>
-
-#include <linux/platform_data/spi-omap2-mcspi.h>
-#include <linux/input/matrix_keypad.h>
-#include <linux/spi/spi.h>
-#include <linux/dm9000.h>
-#include <linux/interrupt.h>
-
-#include "sdram-micron-mt46h32m32lf-6.h"
-#include "mux.h"
-#include "hsmmc.h"
-#include "board-flash.h"
-#include "common-board-devices.h"
-
-#define	NAND_CS			0
-
-#define OMAP_DM9000_GPIO_IRQ	25
-#define OMAP3_DEVKIT_TS_GPIO	27
-
-static struct mtd_partition devkit8000_nand_partitions[] = {
-	/* All the partition sizes are listed in terms of NAND block size */
-	{
-		.name		= "X-Loader",
-		.offset		= 0,
-		.size		= 4 * NAND_BLOCK_SIZE,
-		.mask_flags	= MTD_WRITEABLE,	/* force read-only */
-	},
-	{
-		.name		= "U-Boot",
-		.offset		= MTDPART_OFS_APPEND,	/* Offset = 0x80000 */
-		.size		= 15 * NAND_BLOCK_SIZE,
-		.mask_flags	= MTD_WRITEABLE,	/* force read-only */
-	},
-	{
-		.name		= "U-Boot Env",
-		.offset		= MTDPART_OFS_APPEND,	/* Offset = 0x260000 */
-		.size		= 1 * NAND_BLOCK_SIZE,
-	},
-	{
-		.name		= "Kernel",
-		.offset		= MTDPART_OFS_APPEND,	/* Offset = 0x280000 */
-		.size		= 32 * NAND_BLOCK_SIZE,
-	},
-	{
-		.name		= "File System",
-		.offset		= MTDPART_OFS_APPEND,	/* Offset = 0x680000 */
-		.size		= MTDPART_SIZ_FULL,
-	},
-};
-
-static struct omap2_hsmmc_info mmc[] = {
-	{
-		.mmc		= 1,
-		.caps		= MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA,
-		.gpio_wp	= 29,
-		.deferred	= true,
-	},
-	{}	/* Terminator */
-};
-
-static struct regulator_consumer_supply devkit8000_vmmc1_supply[] = {
-	REGULATOR_SUPPLY("vmmc", "omap_hsmmc.0"),
-};
-
-/* ads7846 on SPI */
-static struct regulator_consumer_supply devkit8000_vio_supply[] = {
-	REGULATOR_SUPPLY("vcc", "spi2.0"),
-};
-
-static const struct display_timing devkit8000_lcd_videomode = {
-	.pixelclock	= { 0, 40000000, 0 },
-
-	.hactive = { 0, 800, 0 },
-	.hfront_porch = { 0, 1, 0 },
-	.hback_porch = { 0, 1, 0 },
-	.hsync_len = { 0, 48, 0 },
-
-	.vactive = { 0, 480, 0 },
-	.vfront_porch = { 0, 12, 0 },
-	.vback_porch = { 0, 25, 0 },
-	.vsync_len = { 0, 3, 0 },
-
-	.flags = DISPLAY_FLAGS_HSYNC_LOW | DISPLAY_FLAGS_VSYNC_LOW |
-		DISPLAY_FLAGS_DE_HIGH | DISPLAY_FLAGS_PIXDATA_POSEDGE,
-};
-
-static struct panel_dpi_platform_data devkit8000_lcd_pdata = {
-	.name                   = "lcd",
-	.source                 = "dpi.0",
-
-	.data_lines		= 24,
-
-	.display_timing		= &devkit8000_lcd_videomode,
-
-	.enable_gpio		= -1,	/* filled in code */
-	.backlight_gpio		= -1,
-};
-
-static struct platform_device devkit8000_lcd_device = {
-	.name                   = "panel-dpi",
-	.id                     = 0,
-	.dev.platform_data      = &devkit8000_lcd_pdata,
-};
-
-static struct connector_dvi_platform_data devkit8000_dvi_connector_pdata = {
-	.name                   = "dvi",
-	.source                 = "tfp410.0",
-	.i2c_bus_num            = 1,
-};
-
-static struct platform_device devkit8000_dvi_connector_device = {
-	.name                   = "connector-dvi",
-	.id                     = 0,
-	.dev.platform_data      = &devkit8000_dvi_connector_pdata,
-};
-
-static struct encoder_tfp410_platform_data devkit8000_tfp410_pdata = {
-	.name                   = "tfp410.0",
-	.source                 = "dpi.0",
-	.data_lines             = 24,
-	.power_down_gpio        = -1,	/* filled in code */
-};
-
-static struct platform_device devkit8000_tfp410_device = {
-	.name                   = "tfp410",
-	.id                     = 0,
-	.dev.platform_data      = &devkit8000_tfp410_pdata,
-};
-
-static struct connector_atv_platform_data devkit8000_tv_pdata = {
-	.name = "tv",
-	.source = "venc.0",
-	.connector_type = OMAP_DSS_VENC_TYPE_SVIDEO,
-	.invert_polarity = false,
-};
-
-static struct platform_device devkit8000_tv_connector_device = {
-	.name                   = "connector-analog-tv",
-	.id                     = 0,
-	.dev.platform_data      = &devkit8000_tv_pdata,
-};
-
-static struct omap_dss_board_info devkit8000_dss_data = {
-	.default_display_name = "lcd",
-};
-
-static uint32_t board_keymap[] = {
-	KEY(0, 0, KEY_1),
-	KEY(1, 0, KEY_2),
-	KEY(2, 0, KEY_3),
-	KEY(0, 1, KEY_4),
-	KEY(1, 1, KEY_5),
-	KEY(2, 1, KEY_6),
-	KEY(3, 1, KEY_F5),
-	KEY(0, 2, KEY_7),
-	KEY(1, 2, KEY_8),
-	KEY(2, 2, KEY_9),
-	KEY(3, 2, KEY_F6),
-	KEY(0, 3, KEY_F7),
-	KEY(1, 3, KEY_0),
-	KEY(2, 3, KEY_F8),
-	PERSISTENT_KEY(4, 5),
-	KEY(4, 4, KEY_VOLUMEUP),
-	KEY(5, 5, KEY_VOLUMEDOWN),
-	0
-};
-
-static struct matrix_keymap_data board_map_data = {
-	.keymap			= board_keymap,
-	.keymap_size		= ARRAY_SIZE(board_keymap),
-};
-
-static struct twl4030_keypad_data devkit8000_kp_data = {
-	.keymap_data	= &board_map_data,
-	.rows		= 6,
-	.cols		= 6,
-	.rep		= 1,
-};
-
-static struct gpio_led gpio_leds[];
-
-static int devkit8000_twl_gpio_setup(struct device *dev,
-		unsigned gpio, unsigned ngpio)
-{
-	/* gpio + 0 is "mmc0_cd" (input/IRQ) */
-	mmc[0].gpio_cd = gpio + 0;
-	omap_hsmmc_late_init(mmc);
-
-	/* TWL4030_GPIO_MAX + 1 == ledB, PMU_STAT (out, active low LED) */
-	gpio_leds[2].gpio = gpio + TWL4030_GPIO_MAX + 1;
-
-	/* TWL4030_GPIO_MAX + 0 is "LCD_PWREN" (out, active high) */
-	devkit8000_lcd_pdata.enable_gpio = gpio + TWL4030_GPIO_MAX + 0;
-
-	/* gpio + 7 is "DVI_PD" (out, active low) */
-	devkit8000_tfp410_pdata.power_down_gpio = gpio + 7;
-
-	return 0;
-}
-
-static struct twl4030_gpio_platform_data devkit8000_gpio_data = {
-	.use_leds	= true,
-	.pulldowns	= BIT(1) | BIT(2) | BIT(6) | BIT(8) | BIT(13)
-				| BIT(15) | BIT(16) | BIT(17),
-	.setup		= devkit8000_twl_gpio_setup,
-};
-
-static struct regulator_consumer_supply devkit8000_vpll1_supplies[] = {
-	REGULATOR_SUPPLY("vdds_dsi", "omapdss"),
-	REGULATOR_SUPPLY("vdds_dsi", "omapdss_dpi.0"),
-	REGULATOR_SUPPLY("vdds_dsi", "omapdss_dsi.0"),
-};
-
-/* VMMC1 for MMC1 pins CMD, CLK, DAT0..DAT3 (20 mA, plus card == max 220 mA) */
-static struct regulator_init_data devkit8000_vmmc1 = {
-	.constraints = {
-		.min_uV			= 1850000,
-		.max_uV			= 3150000,
-		.valid_modes_mask	= REGULATOR_MODE_NORMAL
-					| REGULATOR_MODE_STANDBY,
-		.valid_ops_mask		= REGULATOR_CHANGE_VOLTAGE
-					| REGULATOR_CHANGE_MODE
-					| REGULATOR_CHANGE_STATUS,
-	},
-	.num_consumer_supplies	= ARRAY_SIZE(devkit8000_vmmc1_supply),
-	.consumer_supplies	= devkit8000_vmmc1_supply,
-};
-
-/* VPLL1 for digital video outputs */
-static struct regulator_init_data devkit8000_vpll1 = {
-	.constraints = {
-		.min_uV			= 1800000,
-		.max_uV			= 1800000,
-		.valid_modes_mask	= REGULATOR_MODE_NORMAL
-					| REGULATOR_MODE_STANDBY,
-		.valid_ops_mask		= REGULATOR_CHANGE_MODE
-					| REGULATOR_CHANGE_STATUS,
-	},
-	.num_consumer_supplies	= ARRAY_SIZE(devkit8000_vpll1_supplies),
-	.consumer_supplies	= devkit8000_vpll1_supplies,
-};
-
-/* VAUX4 for ads7846 and nubs */
-static struct regulator_init_data devkit8000_vio = {
-	.constraints = {
-		.min_uV                 = 1800000,
-		.max_uV                 = 1800000,
-		.apply_uV               = true,
-		.valid_modes_mask       = REGULATOR_MODE_NORMAL
-			| REGULATOR_MODE_STANDBY,
-		.valid_ops_mask         = REGULATOR_CHANGE_MODE
-			| REGULATOR_CHANGE_STATUS,
-	},
-	.num_consumer_supplies  = ARRAY_SIZE(devkit8000_vio_supply),
-	.consumer_supplies      = devkit8000_vio_supply,
-};
-
-static struct twl4030_platform_data devkit8000_twldata = {
-	/* platform_data for children goes here */
-	.gpio		= &devkit8000_gpio_data,
-	.vmmc1		= &devkit8000_vmmc1,
-	.vpll1		= &devkit8000_vpll1,
-	.vio		= &devkit8000_vio,
-	.keypad		= &devkit8000_kp_data,
-};
-
-static int __init devkit8000_i2c_init(void)
-{
-	omap3_pmic_get_config(&devkit8000_twldata,
-			  TWL_COMMON_PDATA_USB | TWL_COMMON_PDATA_AUDIO,
-			  TWL_COMMON_REGULATOR_VDAC);
-	omap3_pmic_init("tps65930", &devkit8000_twldata);
-	/* Bus 3 is attached to the DVI port where devices like the pico DLP
-	 * projector don't work reliably with 400kHz */
-	omap_register_i2c_bus(3, 400, NULL, 0);
-	return 0;
-}
-
-static struct gpio_led gpio_leds[] = {
-	{
-		.name			= "led1",
-		.default_trigger	= "heartbeat",
-		.gpio			= 186,
-		.active_low		= true,
-	},
-	{
-		.name			= "led2",
-		.default_trigger	= "mmc0",
-		.gpio			= 163,
-		.active_low		= true,
-	},
-	{
-		.name			= "ledB",
-		.default_trigger	= "none",
-		.gpio			= 153,
-		.active_low             = true,
-	},
-	{
-		.name			= "led3",
-		.default_trigger	= "none",
-		.gpio			= 164,
-		.active_low             = true,
-	},
-};
-
-static struct gpio_led_platform_data gpio_led_info = {
-	.leds		= gpio_leds,
-	.num_leds	= ARRAY_SIZE(gpio_leds),
-};
-
-static struct platform_device leds_gpio = {
-	.name	= "leds-gpio",
-	.id	= -1,
-	.dev	= {
-		.platform_data	= &gpio_led_info,
-	},
-};
-
-static struct gpio_keys_button gpio_buttons[] = {
-	{
-		.code			= BTN_EXTRA,
-		.gpio			= 26,
-		.desc			= "user",
-		.wakeup			= 1,
-	},
-};
-
-static struct gpio_keys_platform_data gpio_key_info = {
-	.buttons	= gpio_buttons,
-	.nbuttons	= ARRAY_SIZE(gpio_buttons),
-};
-
-static struct platform_device keys_gpio = {
-	.name	= "gpio-keys",
-	.id	= -1,
-	.dev	= {
-		.platform_data	= &gpio_key_info,
-	},
-};
-
-#define OMAP_DM9000_BASE	0x2c000000
-
-static struct resource omap_dm9000_resources[] = {
-	[0] = {
-		.start		= OMAP_DM9000_BASE,
-		.end		= (OMAP_DM9000_BASE + 0x4 - 1),
-		.flags		= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start		= (OMAP_DM9000_BASE + 0x400),
-		.end		= (OMAP_DM9000_BASE + 0x400 + 0x4 - 1),
-		.flags		= IORESOURCE_MEM,
-	},
-	[2] = {
-		.flags		= IORESOURCE_IRQ | IRQF_TRIGGER_LOW,
-	},
-};
-
-static struct dm9000_plat_data omap_dm9000_platdata = {
-	.flags = DM9000_PLATF_16BITONLY,
-};
-
-static struct platform_device omap_dm9000_dev = {
-	.name = "dm9000",
-	.id = -1,
-	.num_resources	= ARRAY_SIZE(omap_dm9000_resources),
-	.resource	= omap_dm9000_resources,
-	.dev = {
-		.platform_data = &omap_dm9000_platdata,
-	},
-};
-
-static void __init omap_dm9000_init(void)
-{
-	unsigned char *eth_addr = omap_dm9000_platdata.dev_addr;
-	struct omap_die_id odi;
-	int ret;
-
-	ret = gpio_request_one(OMAP_DM9000_GPIO_IRQ, GPIOF_IN, "dm9000 irq");
-	if (ret < 0) {
-		printk(KERN_ERR "Failed to request GPIO%d for dm9000 IRQ\n",
-			OMAP_DM9000_GPIO_IRQ);
-		return;
-	}
-
-	/* init the mac address using DIE id */
-	omap_get_die_id(&odi);
-
-	eth_addr[0] = 0x02; /* locally administered */
-	eth_addr[1] = odi.id_1 & 0xff;
-	eth_addr[2] = (odi.id_0 & 0xff000000) >> 24;
-	eth_addr[3] = (odi.id_0 & 0x00ff0000) >> 16;
-	eth_addr[4] = (odi.id_0 & 0x0000ff00) >> 8;
-	eth_addr[5] = (odi.id_0 & 0x000000ff);
-}
-
-static struct platform_device *devkit8000_devices[] __initdata = {
-	&leds_gpio,
-	&keys_gpio,
-	&omap_dm9000_dev,
-	&devkit8000_lcd_device,
-	&devkit8000_tfp410_device,
-	&devkit8000_dvi_connector_device,
-	&devkit8000_tv_connector_device,
-};
-
-static struct usbhs_omap_platform_data usbhs_bdata __initdata = {
-	.port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
-};
-
-#ifdef CONFIG_OMAP_MUX
-static struct omap_board_mux board_mux[] __initdata = {
-	/* nCS and IRQ for Devkit8000 ethernet */
-	OMAP3_MUX(GPMC_NCS6, OMAP_MUX_MODE0),
-	OMAP3_MUX(ETK_D11, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLUP),
-
-	/* McSPI 2*/
-	OMAP3_MUX(MCSPI2_CLK, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(MCSPI2_SIMO, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(MCSPI2_SOMI, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(MCSPI2_CS0, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(MCSPI2_CS1, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-
-	/* PENDOWN GPIO */
-	OMAP3_MUX(ETK_D13, OMAP_MUX_MODE4 | OMAP_PIN_INPUT),
-
-	/* mUSB */
-	OMAP3_MUX(HSUSB0_CLK, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(HSUSB0_STP, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(HSUSB0_DIR, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(HSUSB0_NXT, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(HSUSB0_DATA0, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(HSUSB0_DATA1, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(HSUSB0_DATA2, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(HSUSB0_DATA3, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(HSUSB0_DATA4, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(HSUSB0_DATA5, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(HSUSB0_DATA6, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(HSUSB0_DATA7, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-
-	/* USB 1 */
-	OMAP3_MUX(ETK_CTL, OMAP_MUX_MODE3 | OMAP_PIN_INPUT),
-	OMAP3_MUX(ETK_CLK, OMAP_MUX_MODE3 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(ETK_D8, OMAP_MUX_MODE3 | OMAP_PIN_INPUT),
-	OMAP3_MUX(ETK_D9, OMAP_MUX_MODE3 | OMAP_PIN_INPUT),
-	OMAP3_MUX(ETK_D0, OMAP_MUX_MODE3 | OMAP_PIN_INPUT),
-	OMAP3_MUX(ETK_D1, OMAP_MUX_MODE3 | OMAP_PIN_INPUT),
-	OMAP3_MUX(ETK_D2, OMAP_MUX_MODE3 | OMAP_PIN_INPUT),
-	OMAP3_MUX(ETK_D3, OMAP_MUX_MODE3 | OMAP_PIN_INPUT),
-	OMAP3_MUX(ETK_D4, OMAP_MUX_MODE3 | OMAP_PIN_INPUT),
-	OMAP3_MUX(ETK_D5, OMAP_MUX_MODE3 | OMAP_PIN_INPUT),
-	OMAP3_MUX(ETK_D6, OMAP_MUX_MODE3 | OMAP_PIN_INPUT),
-	OMAP3_MUX(ETK_D7, OMAP_MUX_MODE3 | OMAP_PIN_INPUT),
-
-	/* MMC 1 */
-	OMAP3_MUX(SDMMC1_CLK, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(SDMMC1_CMD, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(SDMMC1_DAT0, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(SDMMC1_DAT1, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(SDMMC1_DAT2, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(SDMMC1_DAT3, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(SDMMC1_DAT4, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(SDMMC1_DAT5, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(SDMMC1_DAT6, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(SDMMC1_DAT7, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-
-	/* McBSP 2 */
-	OMAP3_MUX(MCBSP2_FSX, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(MCBSP2_CLKX, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(MCBSP2_DR, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(MCBSP2_DX, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-
-	/* I2C 1 */
-	OMAP3_MUX(I2C1_SCL, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(I2C1_SDA, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-
-	/* I2C 2 */
-	OMAP3_MUX(I2C2_SCL, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(I2C2_SDA, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-
-	/* I2C 3 */
-	OMAP3_MUX(I2C3_SCL, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(I2C3_SDA, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-
-	/* I2C 4 */
-	OMAP3_MUX(I2C4_SCL, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(I2C4_SDA, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-
-	/* serial ports */
-	OMAP3_MUX(MCBSP3_CLKX, OMAP_MUX_MODE1 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(MCBSP3_FSX, OMAP_MUX_MODE1 | OMAP_PIN_INPUT),
-	OMAP3_MUX(UART1_TX, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(UART1_RX, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-
-	/* DSS */
-	OMAP3_MUX(DSS_PCLK, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_HSYNC, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_VSYNC, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_ACBIAS, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA0, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA1, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA2, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA3, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA4, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA5, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA6, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA7, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA8, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA9, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA10, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA11, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA12, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA13, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA14, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA15, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA16, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA17, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA18, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA19, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA20, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA21, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA22, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA23, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-
-	/* expansion port */
-	/* McSPI 1 */
-	OMAP3_MUX(MCSPI1_CLK, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(MCSPI1_SIMO, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(MCSPI1_SOMI, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(MCSPI1_CS0, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLDOWN),
-	OMAP3_MUX(MCSPI1_CS3, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLDOWN),
-
-	/* HDQ */
-	OMAP3_MUX(HDQ_SIO, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-
-	/* McSPI4 */
-	OMAP3_MUX(MCBSP1_CLKR, OMAP_MUX_MODE1 | OMAP_PIN_INPUT),
-	OMAP3_MUX(MCBSP1_DX, OMAP_MUX_MODE1 | OMAP_PIN_INPUT),
-	OMAP3_MUX(MCBSP1_DR, OMAP_MUX_MODE1 | OMAP_PIN_INPUT),
-	OMAP3_MUX(MCBSP1_FSX, OMAP_MUX_MODE1 | OMAP_PIN_INPUT_PULLUP),
-
-	/* MMC 2 */
-	OMAP3_MUX(SDMMC2_DAT4, OMAP_MUX_MODE1 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(SDMMC2_DAT5, OMAP_MUX_MODE1 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(SDMMC2_DAT6, OMAP_MUX_MODE1 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(SDMMC2_DAT7, OMAP_MUX_MODE1 | OMAP_PIN_INPUT),
-
-	/* I2C3 */
-	OMAP3_MUX(I2C3_SCL, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(I2C3_SDA, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-
-	OMAP3_MUX(MCBSP1_CLKX, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(MCBSP_CLKS, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(MCBSP1_FSR, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT),
-
-	OMAP3_MUX(GPMC_NCS7, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(GPMC_NCS3, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT),
-
-	/* TPS IRQ */
-	OMAP3_MUX(SYS_NIRQ, OMAP_MUX_MODE0 | OMAP_WAKEUP_EN | \
-			OMAP_PIN_INPUT_PULLUP),
-
-	{ .reg_offset = OMAP_MUX_TERMINATOR },
-};
-#endif
-
-static void __init devkit8000_init(void)
-{
-	omap3_mux_init(board_mux, OMAP_PACKAGE_CUS);
-	omap_serial_init();
-	omap_sdrc_init(mt46h32m32lf6_sdrc_params,
-				  mt46h32m32lf6_sdrc_params);
-
-	omap_dm9000_init();
-
-	omap_hsmmc_init(mmc);
-	devkit8000_i2c_init();
-	omap_dm9000_resources[2].start = gpio_to_irq(OMAP_DM9000_GPIO_IRQ);
-	platform_add_devices(devkit8000_devices,
-			ARRAY_SIZE(devkit8000_devices));
-
-	omap_display_init(&devkit8000_dss_data);
-
-	omap_ads7846_init(2, OMAP3_DEVKIT_TS_GPIO, 0, NULL);
-
-	usb_bind_phy("musb-hdrc.0.auto", 0, "twl4030_usb");
-	usb_musb_init(NULL);
-	usbhs_init(&usbhs_bdata);
-	board_nand_init(devkit8000_nand_partitions,
-			ARRAY_SIZE(devkit8000_nand_partitions), NAND_CS,
-			NAND_BUSWIDTH_16, NULL);
-	omap_twl4030_audio_init("omap3beagle", NULL);
-
-	/* Ensure SDRC pins are mux'd for self-refresh */
-	omap_mux_init_signal("sdrc_cke0", OMAP_PIN_OUTPUT);
-	omap_mux_init_signal("sdrc_cke1", OMAP_PIN_OUTPUT);
-}
-
-MACHINE_START(DEVKIT8000, "OMAP3 Devkit8000")
-	.atag_offset	= 0x100,
-	.reserve	= omap_reserve,
-	.map_io		= omap3_map_io,
-	.init_early	= omap35xx_init_early,
-	.init_irq	= omap3_init_irq,
-	.init_machine	= devkit8000_init,
-	.init_late	= omap35xx_init_late,
-	.init_time	= omap3_secure_sync32k_timer_init,
-	.restart	= omap3xxx_restart,
-MACHINE_END
diff --git a/arch/arm/mach-omap2/board-omap3stalker.c b/arch/arm/mach-omap2/board-omap3stalker.c
deleted file mode 100644
index 6311f4b..0000000
--- a/arch/arm/mach-omap2/board-omap3stalker.c
+++ /dev/null
@@ -1,433 +0,0 @@
-/*
- * linux/arch/arm/mach-omap2/board-omap3evm.c
- *
- * Copyright (C) 2008 Guangzhou EMA-Tech
- *
- * Modified from mach-omap2/board-omap3evm.c
- *
- * Initial code: Syed Mohammed Khasim
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/delay.h>
-#include <linux/err.h>
-#include <linux/clk.h>
-#include <linux/io.h>
-#include <linux/leds.h>
-#include <linux/gpio.h>
-#include <linux/input.h>
-#include <linux/gpio_keys.h>
-
-#include <linux/regulator/fixed.h>
-#include <linux/regulator/machine.h>
-#include <linux/i2c/twl.h>
-#include <linux/mmc/host.h>
-#include <linux/input/matrix_keypad.h>
-#include <linux/spi/spi.h>
-#include <linux/interrupt.h>
-#include <linux/smsc911x.h>
-#include <linux/platform_data/at24.h>
-#include <linux/usb/phy.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <asm/mach/flash.h>
-
-#include "common.h"
-#include "gpmc.h"
-#include <linux/platform_data/mtd-nand-omap2.h>
-#include <video/omapdss.h>
-#include <video/omap-panel-data.h>
-
-#include <linux/platform_data/spi-omap2-mcspi.h>
-
-#include "sdram-micron-mt46h32m32lf-6.h"
-#include "mux.h"
-#include "hsmmc.h"
-#include "common-board-devices.h"
-
-#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
-#include "gpmc-smsc911x.h"
-
-#define OMAP3STALKER_ETHR_START	0x2c000000
-#define OMAP3STALKER_ETHR_SIZE	1024
-#define OMAP3STALKER_ETHR_GPIO_IRQ	19
-#define OMAP3STALKER_SMC911X_CS	5
-
-static struct omap_smsc911x_platform_data smsc911x_cfg = {
-	.cs             = OMAP3STALKER_SMC911X_CS,
-	.gpio_irq       = OMAP3STALKER_ETHR_GPIO_IRQ,
-	.gpio_reset     = -EINVAL,
-	.flags		= (SMSC911X_USE_32BIT | SMSC911X_SAVE_MAC_ADDRESS),
-};
-
-static inline void __init omap3stalker_init_eth(void)
-{
-	omap_mux_init_gpio(19, OMAP_PIN_INPUT_PULLUP);
-	gpmc_smsc911x_init(&smsc911x_cfg);
-}
-
-#else
-static inline void __init omap3stalker_init_eth(void)
-{
-	return;
-}
-#endif
-
-/*
- * OMAP3 DSS control signals
- */
-
-#define DSS_ENABLE_GPIO	199
-#define LCD_PANEL_BKLIGHT_GPIO	210
-#define ENABLE_VPLL2_DEV_GRP	0xE0
-
-static void __init omap3_stalker_display_init(void)
-{
-	return;
-}
-static struct connector_dvi_platform_data omap3stalker_dvi_connector_pdata = {
-	.name                   = "dvi",
-	.source                 = "tfp410.0",
-	.i2c_bus_num            = -1,
-};
-
-static struct platform_device omap3stalker_dvi_connector_device = {
-	.name                   = "connector-dvi",
-	.id                     = 0,
-	.dev.platform_data      = &omap3stalker_dvi_connector_pdata,
-};
-
-static struct encoder_tfp410_platform_data omap3stalker_tfp410_pdata = {
-	.name                   = "tfp410.0",
-	.source                 = "dpi.0",
-	.data_lines             = 24,
-	.power_down_gpio        = DSS_ENABLE_GPIO,
-};
-
-static struct platform_device omap3stalker_tfp410_device = {
-	.name                   = "tfp410",
-	.id                     = 0,
-	.dev.platform_data      = &omap3stalker_tfp410_pdata,
-};
-
-static struct connector_atv_platform_data omap3stalker_tv_pdata = {
-	.name = "tv",
-	.source = "venc.0",
-	.connector_type = OMAP_DSS_VENC_TYPE_COMPOSITE,
-	.invert_polarity = false,
-};
-
-static struct platform_device omap3stalker_tv_connector_device = {
-	.name                   = "connector-analog-tv",
-	.id                     = 0,
-	.dev.platform_data      = &omap3stalker_tv_pdata,
-};
-
-static struct omap_dss_board_info omap3_stalker_dss_data = {
-	.default_display_name = "dvi",
-};
-
-static struct regulator_consumer_supply omap3stalker_vmmc1_supply[] = {
-	REGULATOR_SUPPLY("vmmc", "omap_hsmmc.0"),
-};
-
-static struct regulator_consumer_supply omap3stalker_vsim_supply[] = {
-	REGULATOR_SUPPLY("vmmc_aux", "omap_hsmmc.0"),
-};
-
-/* VMMC1 for MMC1 pins CMD, CLK, DAT0..DAT3 (20 mA, plus card == max 220 mA) */
-static struct regulator_init_data omap3stalker_vmmc1 = {
-	.constraints		= {
-		.min_uV			= 1850000,
-		.max_uV			= 3150000,
-		.valid_modes_mask	= REGULATOR_MODE_NORMAL
-		| REGULATOR_MODE_STANDBY,
-		.valid_ops_mask		= REGULATOR_CHANGE_VOLTAGE
-		| REGULATOR_CHANGE_MODE | REGULATOR_CHANGE_STATUS,
-	},
-	.num_consumer_supplies	= ARRAY_SIZE(omap3stalker_vmmc1_supply),
-	.consumer_supplies	= omap3stalker_vmmc1_supply,
-};
-
-/* VSIM for MMC1 pins DAT4..DAT7 (2 mA, plus card == max 50 mA) */
-static struct regulator_init_data omap3stalker_vsim = {
-	.constraints		= {
-		.min_uV			= 1800000,
-		.max_uV			= 3000000,
-		.valid_modes_mask	= REGULATOR_MODE_NORMAL
-		| REGULATOR_MODE_STANDBY,
-		.valid_ops_mask		= REGULATOR_CHANGE_VOLTAGE
-		| REGULATOR_CHANGE_MODE | REGULATOR_CHANGE_STATUS,
-	},
-	.num_consumer_supplies	= ARRAY_SIZE(omap3stalker_vsim_supply),
-	.consumer_supplies	= omap3stalker_vsim_supply,
-};
-
-static struct omap2_hsmmc_info mmc[] = {
-	{
-		.mmc		= 1,
-		.caps		= MMC_CAP_4_BIT_DATA,
-		.gpio_cd	= -EINVAL,
-		.gpio_wp	= 23,
-		.deferred	= true,
-	 },
-	{}			/* Terminator */
-};
-
-static struct gpio_keys_button gpio_buttons[] = {
-	{
-	 .code		= BTN_EXTRA,
-	 .gpio		= 18,
-	 .desc		= "user",
-	 .wakeup	= 1,
-	 },
-};
-
-static struct gpio_keys_platform_data gpio_key_info = {
-	.buttons	= gpio_buttons,
-	.nbuttons	= ARRAY_SIZE(gpio_buttons),
-};
-
-static struct platform_device keys_gpio = {
-	.name		= "gpio-keys",
-	.id		= -1,
-	.dev		= {
-		.platform_data	= &gpio_key_info,
-	},
-};
-
-static struct gpio_led gpio_leds[] = {
-	{
-	 .name			= "stalker:D8:usr0",
-	 .default_trigger	= "default-on",
-	 .gpio			= 126,
-	 },
-	{
-	 .name			= "stalker:D9:usr1",
-	 .default_trigger	= "default-on",
-	 .gpio			= 127,
-	 },
-	{
-	 .name			= "stalker:D3:mmc0",
-	 .gpio			= -EINVAL,	/* gets replaced */
-	 .active_low		= true,
-	 .default_trigger	= "mmc0",
-	 },
-	{
-	 .name			= "stalker:D4:heartbeat",
-	 .gpio			= -EINVAL,	/* gets replaced */
-	 .active_low		= true,
-	 .default_trigger	= "heartbeat",
-	 },
-};
-
-static struct gpio_led_platform_data gpio_led_info = {
-	.leds		= gpio_leds,
-	.num_leds	= ARRAY_SIZE(gpio_leds),
-};
-
-static struct platform_device leds_gpio = {
-	.name	= "leds-gpio",
-	.id	= -1,
-	.dev	= {
-		.platform_data	= &gpio_led_info,
-	},
-};
-
-static int
-omap3stalker_twl_gpio_setup(struct device *dev,
-			    unsigned gpio, unsigned ngpio)
-{
-	/* gpio + 0 is "mmc0_cd" (input/IRQ) */
-	mmc[0].gpio_cd = gpio + 0;
-	omap_hsmmc_late_init(mmc);
-
-	/*
-	 * Most GPIOs are for USB OTG.  Some are mostly sent to
-	 * the P2 connector; notably LEDA for the LCD backlight.
-	 */
-
-	/* TWL4030_GPIO_MAX + 0 == ledA, LCD Backlight control */
-	gpio_request_one(gpio + TWL4030_GPIO_MAX, GPIOF_OUT_INIT_LOW,
-			 "EN_LCD_BKL");
-
-	/* gpio + 7 == DVI Enable */
-	gpio_request_one(gpio + 7, GPIOF_OUT_INIT_LOW, "EN_DVI");
-
-	/* TWL4030_GPIO_MAX + 1 == ledB (out, mmc0) */
-	gpio_leds[2].gpio = gpio + TWL4030_GPIO_MAX + 1;
-	/* GPIO + 13 == ledsync (out, heartbeat) */
-	gpio_leds[3].gpio = gpio + 13;
-
-	platform_device_register(&leds_gpio);
-	return 0;
-}
-
-static struct twl4030_gpio_platform_data omap3stalker_gpio_data = {
-	.use_leds	= true,
-	.setup		= omap3stalker_twl_gpio_setup,
-};
-
-static uint32_t board_keymap[] = {
-	KEY(0, 0, KEY_LEFT),
-	KEY(0, 1, KEY_DOWN),
-	KEY(0, 2, KEY_ENTER),
-	KEY(0, 3, KEY_M),
-
-	KEY(1, 0, KEY_RIGHT),
-	KEY(1, 1, KEY_UP),
-	KEY(1, 2, KEY_I),
-	KEY(1, 3, KEY_N),
-
-	KEY(2, 0, KEY_A),
-	KEY(2, 1, KEY_E),
-	KEY(2, 2, KEY_J),
-	KEY(2, 3, KEY_O),
-
-	KEY(3, 0, KEY_B),
-	KEY(3, 1, KEY_F),
-	KEY(3, 2, KEY_K),
-	KEY(3, 3, KEY_P)
-};
-
-static struct matrix_keymap_data board_map_data = {
-	.keymap		= board_keymap,
-	.keymap_size	= ARRAY_SIZE(board_keymap),
-};
-
-static struct twl4030_keypad_data omap3stalker_kp_data = {
-	.keymap_data	= &board_map_data,
-	.rows		= 4,
-	.cols		= 4,
-	.rep		= 1,
-};
-
-static struct twl4030_platform_data omap3stalker_twldata = {
-	/* platform_data for children goes here */
-	.keypad		= &omap3stalker_kp_data,
-	.gpio		= &omap3stalker_gpio_data,
-	.vmmc1		= &omap3stalker_vmmc1,
-	.vsim		= &omap3stalker_vsim,
-};
-
-static struct at24_platform_data fram_info = {
-	.byte_len	= (64 * 1024) / 8,
-	.page_size	= 8192,
-	.flags		= AT24_FLAG_ADDR16 | AT24_FLAG_IRUGO,
-};
-
-static struct i2c_board_info __initdata omap3stalker_i2c_boardinfo3[] = {
-	{
-	 I2C_BOARD_INFO("24c64", 0x50),
-	 .flags		= I2C_CLIENT_WAKE,
-	 .platform_data	= &fram_info,
-	 },
-};
-
-static int __init omap3_stalker_i2c_init(void)
-{
-	omap3_pmic_get_config(&omap3stalker_twldata,
-			TWL_COMMON_PDATA_USB | TWL_COMMON_PDATA_MADC |
-			TWL_COMMON_PDATA_AUDIO,
-			TWL_COMMON_REGULATOR_VDAC | TWL_COMMON_REGULATOR_VPLL2);
-
-	omap3stalker_twldata.vdac->constraints.apply_uV = true;
-	omap3stalker_twldata.vpll2->constraints.apply_uV = true;
-	omap3stalker_twldata.vpll2->constraints.name = "VDVI";
-
-	omap3_pmic_init("twl4030", &omap3stalker_twldata);
-	omap_register_i2c_bus(2, 400, NULL, 0);
-	omap_register_i2c_bus(3, 400, omap3stalker_i2c_boardinfo3,
-			      ARRAY_SIZE(omap3stalker_i2c_boardinfo3));
-	return 0;
-}
-
-#define OMAP3_STALKER_TS_GPIO	175
-
-static struct usbhs_phy_data phy_data[] __initdata = {
-	{
-		.port = 2,
-		.reset_gpio = 21,
-		.vcc_gpio = -EINVAL,
-	},
-};
-
-static struct platform_device *omap3_stalker_devices[] __initdata = {
-	&keys_gpio,
-	&omap3stalker_tfp410_device,
-	&omap3stalker_dvi_connector_device,
-	&omap3stalker_tv_connector_device,
-};
-
-static struct usbhs_omap_platform_data usbhs_bdata __initdata = {
-	.port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
-};
-
-#ifdef CONFIG_OMAP_MUX
-static struct omap_board_mux board_mux[] __initdata = {
-	OMAP3_MUX(SYS_NIRQ, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP |
-		  OMAP_PIN_OFF_INPUT_PULLUP | OMAP_PIN_OFF_WAKEUPENABLE),
-	OMAP3_MUX(MCSPI1_CS1, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLUP |
-		  OMAP_PIN_OFF_INPUT_PULLUP | OMAP_PIN_OFF_WAKEUPENABLE),
-	{.reg_offset = OMAP_MUX_TERMINATOR},
-};
-#endif
-
-static struct regulator_consumer_supply dummy_supplies[] = {
-	REGULATOR_SUPPLY("vddvario", "smsc911x.0"),
-	REGULATOR_SUPPLY("vdd33a", "smsc911x.0"),
-};
-
-static void __init omap3_stalker_init(void)
-{
-	regulator_register_fixed(0, dummy_supplies, ARRAY_SIZE(dummy_supplies));
-	omap3_mux_init(board_mux, OMAP_PACKAGE_CUS);
-
-	omap_mux_init_gpio(23, OMAP_PIN_INPUT);
-	omap_hsmmc_init(mmc);
-
-	omap3_stalker_i2c_init();
-
-	platform_add_devices(omap3_stalker_devices,
-			     ARRAY_SIZE(omap3_stalker_devices));
-
-	omap_display_init(&omap3_stalker_dss_data);
-
-	omap_serial_init();
-	omap_sdrc_init(mt46h32m32lf6_sdrc_params, NULL);
-	usb_bind_phy("musb-hdrc.0.auto", 0, "twl4030_usb");
-	usb_musb_init(NULL);
-
-	usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data));
-	usbhs_init(&usbhs_bdata);
-	omap_ads7846_init(1, OMAP3_STALKER_TS_GPIO, 310, NULL);
-
-	omap_mux_init_gpio(21, OMAP_PIN_OUTPUT);
-	omap_mux_init_gpio(18, OMAP_PIN_INPUT_PULLUP);
-
-	omap3stalker_init_eth();
-	omap3_stalker_display_init();
-/* Ensure SDRC pins are mux'd for self-refresh */
-	omap_mux_init_signal("sdr_cke0", OMAP_PIN_OUTPUT);
-	omap_mux_init_signal("sdr_cke1", OMAP_PIN_OUTPUT);
-}
-
-MACHINE_START(SBC3530, "OMAP3 STALKER")
-	/* Maintainer: Jason Lam -lzg@ema-tech.com */
-	.atag_offset		= 0x100,
-	.map_io			= omap3_map_io,
-	.init_early		= omap35xx_init_early,
-	.init_irq		= omap3_init_irq,
-	.init_machine		= omap3_stalker_init,
-	.init_late		= omap35xx_init_late,
-	.init_time		= omap3_secure_sync32k_timer_init,
-	.restart		= omap3xxx_restart,
-MACHINE_END
diff --git a/arch/arm/mach-omap2/board-omap3touchbook.c b/arch/arm/mach-omap2/board-omap3touchbook.c
deleted file mode 100644
index a01993e..0000000
--- a/arch/arm/mach-omap2/board-omap3touchbook.c
+++ /dev/null
@@ -1,395 +0,0 @@
-/*
- * linux/arch/arm/mach-omap2/board-omap3touchbook.c
- *
- * Copyright (C) 2009 Always Innovating
- *
- * Modified from mach-omap2/board-omap3beagleboard.c
- *
- * Initial code: Grégoire Gentil, Tim Yamin
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/delay.h>
-#include <linux/err.h>
-#include <linux/clk.h>
-#include <linux/io.h>
-#include <linux/leds.h>
-#include <linux/gpio.h>
-#include <linux/input.h>
-#include <linux/gpio_keys.h>
-
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/partitions.h>
-#include <linux/mtd/nand.h>
-#include <linux/mmc/host.h>
-#include <linux/usb/phy.h>
-
-#include <linux/platform_data/spi-omap2-mcspi.h>
-#include <linux/spi/spi.h>
-
-#include <linux/spi/ads7846.h>
-
-#include <linux/regulator/machine.h>
-#include <linux/i2c/twl.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <asm/mach/flash.h>
-#include <asm/system_info.h>
-
-#include "common.h"
-#include "gpmc.h"
-#include <linux/platform_data/mtd-nand-omap2.h>
-
-#include "mux.h"
-#include "hsmmc.h"
-#include "board-flash.h"
-#include "common-board-devices.h"
-
-#include <asm/setup.h>
-
-#define OMAP3_AC_GPIO		136
-#define OMAP3_TS_GPIO		162
-#define TB_BL_PWM_TIMER		9
-#define TB_KILL_POWER_GPIO	168
-
-#define	NAND_CS			0
-
-static unsigned long touchbook_revision;
-
-static struct mtd_partition omap3touchbook_nand_partitions[] = {
-	/* All the partition sizes are listed in terms of NAND block size */
-	{
-		.name		= "X-Loader",
-		.offset		= 0,
-		.size		= 4 * NAND_BLOCK_SIZE,
-		.mask_flags	= MTD_WRITEABLE,	/* force read-only */
-	},
-	{
-		.name		= "U-Boot",
-		.offset		= MTDPART_OFS_APPEND,	/* Offset = 0x80000 */
-		.size		= 15 * NAND_BLOCK_SIZE,
-		.mask_flags	= MTD_WRITEABLE,	/* force read-only */
-	},
-	{
-		.name		= "U-Boot Env",
-		.offset		= MTDPART_OFS_APPEND,	/* Offset = 0x260000 */
-		.size		= 1 * NAND_BLOCK_SIZE,
-	},
-	{
-		.name		= "Kernel",
-		.offset		= MTDPART_OFS_APPEND,	/* Offset = 0x280000 */
-		.size		= 32 * NAND_BLOCK_SIZE,
-	},
-	{
-		.name		= "File System",
-		.offset		= MTDPART_OFS_APPEND,	/* Offset = 0x680000 */
-		.size		= MTDPART_SIZ_FULL,
-	},
-};
-
-#include "sdram-micron-mt46h32m32lf-6.h"
-
-static struct omap2_hsmmc_info mmc[] = {
-	{
-		.mmc		= 1,
-		.caps		= MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA,
-		.gpio_wp	= 29,
-		.deferred	= true,
-	},
-	{}	/* Terminator */
-};
-
-static struct regulator_consumer_supply touchbook_vmmc1_supply[] = {
-	REGULATOR_SUPPLY("vmmc", "omap_hsmmc.0"),
-};
-
-static struct regulator_consumer_supply touchbook_vsim_supply[] = {
-	REGULATOR_SUPPLY("vmmc_aux", "omap_hsmmc.0"),
-};
-
-static struct gpio_led gpio_leds[];
-
-static int touchbook_twl_gpio_setup(struct device *dev,
-		unsigned gpio, unsigned ngpio)
-{
-	/* gpio + 0 is "mmc0_cd" (input/IRQ) */
-	mmc[0].gpio_cd = gpio + 0;
-	omap_hsmmc_late_init(mmc);
-
-	/* REVISIT: need ehci-omap hooks for external VBUS
-	 * power switch and overcurrent detect
-	 */
-	gpio_request_one(gpio + 1, GPIOF_IN, "EHCI_nOC");
-
-	/* TWL4030_GPIO_MAX + 0 == ledA, EHCI nEN_USB_PWR (out, active low) */
-	gpio_request_one(gpio + TWL4030_GPIO_MAX, GPIOF_OUT_INIT_LOW,
-			 "nEN_USB_PWR");
-
-	/* TWL4030_GPIO_MAX + 1 == ledB, PMU_STAT (out, active low LED) */
-	gpio_leds[2].gpio = gpio + TWL4030_GPIO_MAX + 1;
-
-	return 0;
-}
-
-static struct twl4030_gpio_platform_data touchbook_gpio_data = {
-	.use_leds	= true,
-	.pullups	= BIT(1),
-	.pulldowns	= BIT(2) | BIT(6) | BIT(7) | BIT(8) | BIT(13)
-				| BIT(15) | BIT(16) | BIT(17),
-	.setup		= touchbook_twl_gpio_setup,
-};
-
-static struct regulator_consumer_supply touchbook_vdac_supply[] = {
-{
-	.supply		= "vdac",
-},
-};
-
-static struct regulator_consumer_supply touchbook_vdvi_supply[] = {
-{
-	.supply		= "vdvi",
-},
-};
-
-/* VMMC1 for MMC1 pins CMD, CLK, DAT0..DAT3 (20 mA, plus card == max 220 mA) */
-static struct regulator_init_data touchbook_vmmc1 = {
-	.constraints = {
-		.min_uV			= 1850000,
-		.max_uV			= 3150000,
-		.valid_modes_mask	= REGULATOR_MODE_NORMAL
-					| REGULATOR_MODE_STANDBY,
-		.valid_ops_mask		= REGULATOR_CHANGE_VOLTAGE
-					| REGULATOR_CHANGE_MODE
-					| REGULATOR_CHANGE_STATUS,
-	},
-	.num_consumer_supplies	= ARRAY_SIZE(touchbook_vmmc1_supply),
-	.consumer_supplies	= touchbook_vmmc1_supply,
-};
-
-/* VSIM for MMC1 pins DAT4..DAT7 (2 mA, plus card == max 50 mA) */
-static struct regulator_init_data touchbook_vsim = {
-	.constraints = {
-		.min_uV			= 1800000,
-		.max_uV			= 3000000,
-		.valid_modes_mask	= REGULATOR_MODE_NORMAL
-					| REGULATOR_MODE_STANDBY,
-		.valid_ops_mask		= REGULATOR_CHANGE_VOLTAGE
-					| REGULATOR_CHANGE_MODE
-					| REGULATOR_CHANGE_STATUS,
-	},
-	.num_consumer_supplies	= ARRAY_SIZE(touchbook_vsim_supply),
-	.consumer_supplies	= touchbook_vsim_supply,
-};
-
-static struct twl4030_platform_data touchbook_twldata = {
-	/* platform_data for children goes here */
-	.gpio		= &touchbook_gpio_data,
-	.vmmc1		= &touchbook_vmmc1,
-	.vsim		= &touchbook_vsim,
-};
-
-static struct i2c_board_info __initdata touchBook_i2c_boardinfo[] = {
-	{
-		I2C_BOARD_INFO("bq27200", 0x55),
-	},
-};
-
-static int __init omap3_touchbook_i2c_init(void)
-{
-	/* Standard TouchBook bus */
-	omap3_pmic_get_config(&touchbook_twldata,
-			TWL_COMMON_PDATA_USB | TWL_COMMON_PDATA_AUDIO,
-			TWL_COMMON_REGULATOR_VDAC | TWL_COMMON_REGULATOR_VPLL2);
-
-	touchbook_twldata.vdac->num_consumer_supplies =
-					ARRAY_SIZE(touchbook_vdac_supply);
-	touchbook_twldata.vdac->consumer_supplies = touchbook_vdac_supply;
-
-	touchbook_twldata.vpll2->constraints.name = "VDVI";
-	touchbook_twldata.vpll2->num_consumer_supplies =
-					ARRAY_SIZE(touchbook_vdvi_supply);
-	touchbook_twldata.vpll2->consumer_supplies = touchbook_vdvi_supply;
-
-	omap3_pmic_init("twl4030", &touchbook_twldata);
-	/* Additional TouchBook bus */
-	omap_register_i2c_bus(3, 100, touchBook_i2c_boardinfo,
-			ARRAY_SIZE(touchBook_i2c_boardinfo));
-
-	return 0;
-}
-
-static struct ads7846_platform_data ads7846_pdata = {
-	.x_min			= 100,
-	.y_min			= 265,
-	.x_max			= 3950,
-	.y_max			= 3750,
-	.x_plate_ohms		= 40,
-	.pressure_max		= 255,
-	.debounce_max		= 10,
-	.debounce_tol		= 5,
-	.debounce_rep		= 1,
-	.gpio_pendown		= OMAP3_TS_GPIO,
-	.keep_vref_on		= 1,
-};
-
-static struct gpio_led gpio_leds[] = {
-	{
-		.name			= "touchbook::usr0",
-		.default_trigger	= "heartbeat",
-		.gpio			= 150,
-	},
-	{
-		.name			= "touchbook::usr1",
-		.default_trigger	= "mmc0",
-		.gpio			= 149,
-	},
-	{
-		.name			= "touchbook::pmu_stat",
-		.gpio			= -EINVAL,	/* gets replaced */
-		.active_low		= true,
-	},
-};
-
-static struct gpio_led_platform_data gpio_led_info = {
-	.leds		= gpio_leds,
-	.num_leds	= ARRAY_SIZE(gpio_leds),
-};
-
-static struct platform_device leds_gpio = {
-	.name	= "leds-gpio",
-	.id	= -1,
-	.dev	= {
-		.platform_data	= &gpio_led_info,
-	},
-};
-
-static struct gpio_keys_button gpio_buttons[] = {
-	{
-		.code			= BTN_EXTRA,
-		.gpio			= 7,
-		.desc			= "user",
-		.wakeup			= 1,
-	},
-	{
-		.code			= KEY_POWER,
-		.gpio			= 183,
-		.desc			= "power",
-		.wakeup			= 1,
-	},
-};
-
-static struct gpio_keys_platform_data gpio_key_info = {
-	.buttons	= gpio_buttons,
-	.nbuttons	= ARRAY_SIZE(gpio_buttons),
-};
-
-static struct platform_device keys_gpio = {
-	.name	= "gpio-keys",
-	.id	= -1,
-	.dev	= {
-		.platform_data	= &gpio_key_info,
-	},
-};
-
-#ifdef CONFIG_OMAP_MUX
-static struct omap_board_mux board_mux[] __initdata = {
-	{ .reg_offset = OMAP_MUX_TERMINATOR },
-};
-#endif
-
-static struct usbhs_phy_data phy_data[] __initdata = {
-	{
-		.port = 2,
-		.reset_gpio = 147,
-		.vcc_gpio = -EINVAL,
-	},
-};
-
-static struct platform_device *omap3_touchbook_devices[] __initdata = {
-	&leds_gpio,
-	&keys_gpio,
-};
-
-static struct usbhs_omap_platform_data usbhs_bdata __initdata = {
-	.port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
-	.port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
-};
-
-static void omap3_touchbook_poweroff(void)
-{
-	int pwr_off = TB_KILL_POWER_GPIO;
-
-	if (gpio_request_one(pwr_off, GPIOF_OUT_INIT_LOW, "DVI reset") < 0)
-		printk(KERN_ERR "Unable to get kill power GPIO\n");
-}
-
-static int __init early_touchbook_revision(char *p)
-{
-	if (!p)
-		return 0;
-
-	return kstrtoul(p, 10, &touchbook_revision);
-}
-early_param("tbr", early_touchbook_revision);
-
-static void __init omap3_touchbook_init(void)
-{
-	omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
-
-	pm_power_off = omap3_touchbook_poweroff;
-
-	if (system_rev >= 0x20 && system_rev <= 0x34301000) {
-		omap_mux_init_gpio(23, OMAP_PIN_INPUT);
-		mmc[0].gpio_wp = 23;
-	} else {
-		omap_mux_init_gpio(29, OMAP_PIN_INPUT);
-	}
-	omap_hsmmc_init(mmc);
-
-	omap3_touchbook_i2c_init();
-	platform_add_devices(omap3_touchbook_devices,
-			ARRAY_SIZE(omap3_touchbook_devices));
-	omap_serial_init();
-	omap_sdrc_init(mt46h32m32lf6_sdrc_params,
-				  mt46h32m32lf6_sdrc_params);
-
-	omap_mux_init_gpio(170, OMAP_PIN_INPUT);
-	/* REVISIT leave DVI powered down until it's needed ... */
-	gpio_request_one(176, GPIOF_OUT_INIT_HIGH, "DVI_nPD");
-
-	/* Touchscreen and accelerometer */
-	omap_ads7846_init(4, OMAP3_TS_GPIO, 310, &ads7846_pdata);
-	usb_bind_phy("musb-hdrc.0.auto", 0, "twl4030_usb");
-	usb_musb_init(NULL);
-
-	usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data));
-	usbhs_init(&usbhs_bdata);
-	board_nand_init(omap3touchbook_nand_partitions,
-			ARRAY_SIZE(omap3touchbook_nand_partitions), NAND_CS,
-			NAND_BUSWIDTH_16, NULL);
-
-	/* Ensure SDRC pins are mux'd for self-refresh */
-	omap_mux_init_signal("sdrc_cke0", OMAP_PIN_OUTPUT);
-	omap_mux_init_signal("sdrc_cke1", OMAP_PIN_OUTPUT);
-}
-
-MACHINE_START(TOUCHBOOK, "OMAP3 touchbook Board")
-	/* Maintainer: Gregoire Gentil - http://www.alwaysinnovating.com */
-	.atag_offset	= 0x100,
-	.reserve	= omap_reserve,
-	.map_io		= omap3_map_io,
-	.init_early	= omap3430_init_early,
-	.init_irq	= omap3_init_irq,
-	.init_machine	= omap3_touchbook_init,
-	.init_late	= omap3430_init_late,
-	.init_time	= omap3_secure_sync32k_timer_init,
-	.restart	= omap3xxx_restart,
-MACHINE_END