diff options
author | Greg Kroah-Hartman <gregkh@linuxfoundation.org> | 2016-01-03 23:15:26 (GMT) |
---|---|---|
committer | Greg Kroah-Hartman <gregkh@linuxfoundation.org> | 2016-01-03 23:15:26 (GMT) |
commit | b40e9dc0b4967b198fefeabab0e2ba673c887ec3 (patch) | |
tree | d50a88c2324d0bd88705d998981cc7dff6e18fe7 | |
parent | daf273350d96241752b00020940c07dc2cff2e0a (diff) | |
parent | 6ff9d2761b8655991f48f113f7edaefea5c92905 (diff) | |
download | linux-b40e9dc0b4967b198fefeabab0e2ba673c887ec3.tar.xz |
Merge tag 'usb-serial-4.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for v4.5-rc1
These updates add support for Moxa UPort 1100-series devices through a
new mxu11x0 driver.
The cp210x driver gains proper support for cp2108 devices by working
around a couple of firmware bugs, and generic wait-until-sent support
(e.g. for tcdrain) is also added.
Included are also some general clean ups.
Signed-off-by: Johan Hovold <johan@kernel.org>
-rw-r--r-- | drivers/usb/serial/Kconfig | 16 | ||||
-rw-r--r-- | drivers/usb/serial/Makefile | 1 | ||||
-rw-r--r-- | drivers/usb/serial/cp210x.c | 186 | ||||
-rw-r--r-- | drivers/usb/serial/io_edgeport.c | 35 | ||||
-rw-r--r-- | drivers/usb/serial/mos7840.c | 2 | ||||
-rw-r--r-- | drivers/usb/serial/mxu11x0.c | 986 |
6 files changed, 1180 insertions, 46 deletions
diff --git a/drivers/usb/serial/Kconfig b/drivers/usb/serial/Kconfig index 56ecb8b..f612dda 100644 --- a/drivers/usb/serial/Kconfig +++ b/drivers/usb/serial/Kconfig @@ -475,6 +475,22 @@ config USB_SERIAL_MOS7840 To compile this driver as a module, choose M here: the module will be called mos7840. If unsure, choose N. +config USB_SERIAL_MXUPORT11 + tristate "USB Moxa UPORT 11x0 Serial Driver" + ---help--- + Say Y here if you want to use a MOXA UPort 11x0 Serial hub. + + This driver supports: + + - UPort 1110 : 1 port RS-232 USB to Serial Hub. + - UPort 1130 : 1 port RS-422/485 USB to Serial Hub. + - UPort 1130I : 1 port RS-422/485 USB to Serial Hub with Isolation. + - UPort 1150 : 1 port RS-232/422/485 USB to Serial Hub. + - UPort 1150I : 1 port RS-232/422/485 USB to Serial Hub with Isolation. + + To compile this driver as a module, choose M here: the + module will be called mxu11x0. + config USB_SERIAL_MXUPORT tristate "USB Moxa UPORT Serial Driver" ---help--- diff --git a/drivers/usb/serial/Makefile b/drivers/usb/serial/Makefile index 349d9df..f3fa5e5 100644 --- a/drivers/usb/serial/Makefile +++ b/drivers/usb/serial/Makefile @@ -38,6 +38,7 @@ obj-$(CONFIG_USB_SERIAL_METRO) += metro-usb.o obj-$(CONFIG_USB_SERIAL_MOS7720) += mos7720.o obj-$(CONFIG_USB_SERIAL_MOS7840) += mos7840.o obj-$(CONFIG_USB_SERIAL_MXUPORT) += mxuport.o +obj-$(CONFIG_USB_SERIAL_MXUPORT11) += mxu11x0.o obj-$(CONFIG_USB_SERIAL_NAVMAN) += navman.o obj-$(CONFIG_USB_SERIAL_OMNINET) += omninet.o obj-$(CONFIG_USB_SERIAL_OPTICON) += opticon.o diff --git a/drivers/usb/serial/cp210x.c b/drivers/usb/serial/cp210x.c index 7d4f51a..8d839d3 100644 --- a/drivers/usb/serial/cp210x.c +++ b/drivers/usb/serial/cp210x.c @@ -38,13 +38,14 @@ static void cp210x_change_speed(struct tty_struct *, struct usb_serial_port *, struct ktermios *); static void cp210x_set_termios(struct tty_struct *, struct usb_serial_port *, struct ktermios*); +static bool cp210x_tx_empty(struct usb_serial_port *port); static int cp210x_tiocmget(struct tty_struct *); static int cp210x_tiocmset(struct tty_struct *, unsigned int, unsigned int); static int cp210x_tiocmset_port(struct usb_serial_port *port, unsigned int, unsigned int); static void cp210x_break_ctl(struct tty_struct *, int); -static int cp210x_startup(struct usb_serial *); -static void cp210x_release(struct usb_serial *); +static int cp210x_port_probe(struct usb_serial_port *); +static int cp210x_port_remove(struct usb_serial_port *); static void cp210x_dtr_rts(struct usb_serial_port *p, int on); static const struct usb_device_id id_table[] = { @@ -196,8 +197,9 @@ static const struct usb_device_id id_table[] = { MODULE_DEVICE_TABLE(usb, id_table); -struct cp210x_serial_private { +struct cp210x_port_private { __u8 bInterfaceNumber; + bool has_swapped_line_ctl; }; static struct usb_serial_driver cp210x_device = { @@ -213,10 +215,11 @@ static struct usb_serial_driver cp210x_device = { .close = cp210x_close, .break_ctl = cp210x_break_ctl, .set_termios = cp210x_set_termios, + .tx_empty = cp210x_tx_empty, .tiocmget = cp210x_tiocmget, .tiocmset = cp210x_tiocmset, - .attach = cp210x_startup, - .release = cp210x_release, + .port_probe = cp210x_port_probe, + .port_remove = cp210x_port_remove, .dtr_rts = cp210x_dtr_rts }; @@ -299,6 +302,25 @@ static struct usb_serial_driver * const serial_drivers[] = { #define CONTROL_WRITE_DTR 0x0100 #define CONTROL_WRITE_RTS 0x0200 +/* CP210X_GET_COMM_STATUS returns these 0x13 bytes */ +struct cp210x_comm_status { + __le32 ulErrors; + __le32 ulHoldReasons; + __le32 ulAmountInInQueue; + __le32 ulAmountInOutQueue; + u8 bEofReceived; + u8 bWaitForImmediate; + u8 bReserved; +} __packed; + +/* + * CP210X_PURGE - 16 bits passed in wValue of USB request. + * SiLabs app note AN571 gives a strange description of the 4 bits: + * bit 0 or bit 2 clears the transmit queue and 1 or 3 receive. + * writing 1 to all, however, purges cp2108 well enough to avoid the hang. + */ +#define PURGE_ALL 0x000f + /* * cp210x_get_config * Reads from the CP210x configuration registers @@ -310,7 +332,7 @@ static int cp210x_get_config(struct usb_serial_port *port, u8 request, unsigned int *data, int size) { struct usb_serial *serial = port->serial; - struct cp210x_serial_private *spriv = usb_get_serial_data(serial); + struct cp210x_port_private *port_priv = usb_get_serial_port_data(port); __le32 *buf; int result, i, length; @@ -324,7 +346,7 @@ static int cp210x_get_config(struct usb_serial_port *port, u8 request, /* Issue the request, attempting to read 'size' bytes */ result = usb_control_msg(serial->dev, usb_rcvctrlpipe(serial->dev, 0), request, REQTYPE_INTERFACE_TO_HOST, 0x0000, - spriv->bInterfaceNumber, buf, size, + port_priv->bInterfaceNumber, buf, size, USB_CTRL_GET_TIMEOUT); /* Convert data into an array of integers */ @@ -355,7 +377,7 @@ static int cp210x_set_config(struct usb_serial_port *port, u8 request, unsigned int *data, int size) { struct usb_serial *serial = port->serial; - struct cp210x_serial_private *spriv = usb_get_serial_data(serial); + struct cp210x_port_private *port_priv = usb_get_serial_port_data(port); __le32 *buf; int result, i, length; @@ -374,13 +396,13 @@ static int cp210x_set_config(struct usb_serial_port *port, u8 request, result = usb_control_msg(serial->dev, usb_sndctrlpipe(serial->dev, 0), request, REQTYPE_HOST_TO_INTERFACE, 0x0000, - spriv->bInterfaceNumber, buf, size, + port_priv->bInterfaceNumber, buf, size, USB_CTRL_SET_TIMEOUT); } else { result = usb_control_msg(serial->dev, usb_sndctrlpipe(serial->dev, 0), request, REQTYPE_HOST_TO_INTERFACE, data[0], - spriv->bInterfaceNumber, NULL, 0, + port_priv->bInterfaceNumber, NULL, 0, USB_CTRL_SET_TIMEOUT); } @@ -410,6 +432,60 @@ static inline int cp210x_set_config_single(struct usb_serial_port *port, } /* + * Detect CP2108 GET_LINE_CTL bug and activate workaround. + * Write a known good value 0x800, read it back. + * If it comes back swapped the bug is detected. + * Preserve the original register value. + */ +static int cp210x_detect_swapped_line_ctl(struct usb_serial_port *port) +{ + struct cp210x_port_private *port_priv = usb_get_serial_port_data(port); + unsigned int line_ctl_save; + unsigned int line_ctl_test; + int err; + + err = cp210x_get_config(port, CP210X_GET_LINE_CTL, &line_ctl_save, 2); + if (err) + return err; + + line_ctl_test = 0x800; + err = cp210x_set_config(port, CP210X_SET_LINE_CTL, &line_ctl_test, 2); + if (err) + return err; + + err = cp210x_get_config(port, CP210X_GET_LINE_CTL, &line_ctl_test, 2); + if (err) + return err; + + if (line_ctl_test == 8) { + port_priv->has_swapped_line_ctl = true; + line_ctl_save = swab16((u16)line_ctl_save); + } + + return cp210x_set_config(port, CP210X_SET_LINE_CTL, &line_ctl_save, 2); +} + +/* + * Must always be called instead of cp210x_get_config(CP210X_GET_LINE_CTL) + * to workaround cp2108 bug and get correct value. + */ +static int cp210x_get_line_ctl(struct usb_serial_port *port, unsigned int *ctl) +{ + struct cp210x_port_private *port_priv = usb_get_serial_port_data(port); + int err; + + err = cp210x_get_config(port, CP210X_GET_LINE_CTL, ctl, 2); + if (err) + return err; + + /* Workaround swapped bytes in 16-bit value from CP210X_GET_LINE_CTL */ + if (port_priv->has_swapped_line_ctl) + *ctl = swab16((u16)(*ctl)); + + return 0; +} + +/* * cp210x_quantise_baudrate * Quantises the baud rate as per AN205 Table 1 */ @@ -474,11 +550,63 @@ static int cp210x_open(struct tty_struct *tty, struct usb_serial_port *port) static void cp210x_close(struct usb_serial_port *port) { + unsigned int purge_ctl; + usb_serial_generic_close(port); + + /* Clear both queues; cp2108 needs this to avoid an occasional hang */ + purge_ctl = PURGE_ALL; + cp210x_set_config(port, CP210X_PURGE, &purge_ctl, 2); + cp210x_set_config_single(port, CP210X_IFC_ENABLE, UART_DISABLE); } /* + * Read how many bytes are waiting in the TX queue. + */ +static int cp210x_get_tx_queue_byte_count(struct usb_serial_port *port, + u32 *count) +{ + struct usb_serial *serial = port->serial; + struct cp210x_port_private *port_priv = usb_get_serial_port_data(port); + struct cp210x_comm_status *sts; + int result; + + sts = kmalloc(sizeof(*sts), GFP_KERNEL); + if (!sts) + return -ENOMEM; + + result = usb_control_msg(serial->dev, usb_rcvctrlpipe(serial->dev, 0), + CP210X_GET_COMM_STATUS, REQTYPE_INTERFACE_TO_HOST, + 0, port_priv->bInterfaceNumber, sts, sizeof(*sts), + USB_CTRL_GET_TIMEOUT); + if (result == sizeof(*sts)) { + *count = le32_to_cpu(sts->ulAmountInOutQueue); + result = 0; + } else { + dev_err(&port->dev, "failed to get comm status: %d\n", result); + if (result >= 0) + result = -EPROTO; + } + + kfree(sts); + + return result; +} + +static bool cp210x_tx_empty(struct usb_serial_port *port) +{ + int err; + u32 count; + + err = cp210x_get_tx_queue_byte_count(port, &count); + if (err) + return true; + + return !count; +} + +/* * cp210x_get_termios * Reads the baud rate, data bits, parity, stop bits and flow control mode * from the device, corrects any unsupported values, and configures the @@ -519,7 +647,7 @@ static void cp210x_get_termios_port(struct usb_serial_port *port, cflag = *cflagp; - cp210x_get_config(port, CP210X_GET_LINE_CTL, &bits, 2); + cp210x_get_line_ctl(port, &bits); cflag &= ~CSIZE; switch (bits & BITS_DATA_MASK) { case BITS_DATA_5: @@ -687,7 +815,7 @@ static void cp210x_set_termios(struct tty_struct *tty, /* If the number of data bits is to be updated */ if ((cflag & CSIZE) != (old_cflag & CSIZE)) { - cp210x_get_config(port, CP210X_GET_LINE_CTL, &bits, 2); + cp210x_get_line_ctl(port, &bits); bits &= ~BITS_DATA_MASK; switch (cflag & CSIZE) { case CS5: @@ -721,7 +849,7 @@ static void cp210x_set_termios(struct tty_struct *tty, if ((cflag & (PARENB|PARODD|CMSPAR)) != (old_cflag & (PARENB|PARODD|CMSPAR))) { - cp210x_get_config(port, CP210X_GET_LINE_CTL, &bits, 2); + cp210x_get_line_ctl(port, &bits); bits &= ~BITS_PARITY_MASK; if (cflag & PARENB) { if (cflag & CMSPAR) { @@ -747,7 +875,7 @@ static void cp210x_set_termios(struct tty_struct *tty, } if ((cflag & CSTOPB) != (old_cflag & CSTOPB)) { - cp210x_get_config(port, CP210X_GET_LINE_CTL, &bits, 2); + cp210x_get_line_ctl(port, &bits); bits &= ~BITS_STOP_MASK; if (cflag & CSTOPB) { bits |= BITS_STOP_2; @@ -862,29 +990,39 @@ static void cp210x_break_ctl(struct tty_struct *tty, int break_state) cp210x_set_config(port, CP210X_SET_BREAK, &state, 2); } -static int cp210x_startup(struct usb_serial *serial) +static int cp210x_port_probe(struct usb_serial_port *port) { + struct usb_serial *serial = port->serial; struct usb_host_interface *cur_altsetting; - struct cp210x_serial_private *spriv; + struct cp210x_port_private *port_priv; + int ret; - spriv = kzalloc(sizeof(*spriv), GFP_KERNEL); - if (!spriv) + port_priv = kzalloc(sizeof(*port_priv), GFP_KERNEL); + if (!port_priv) return -ENOMEM; cur_altsetting = serial->interface->cur_altsetting; - spriv->bInterfaceNumber = cur_altsetting->desc.bInterfaceNumber; + port_priv->bInterfaceNumber = cur_altsetting->desc.bInterfaceNumber; + + usb_set_serial_port_data(port, port_priv); - usb_set_serial_data(serial, spriv); + ret = cp210x_detect_swapped_line_ctl(port); + if (ret) { + kfree(port_priv); + return ret; + } return 0; } -static void cp210x_release(struct usb_serial *serial) +static int cp210x_port_remove(struct usb_serial_port *port) { - struct cp210x_serial_private *spriv; + struct cp210x_port_private *port_priv; + + port_priv = usb_get_serial_port_data(port); + kfree(port_priv); - spriv = usb_get_serial_data(serial); - kfree(spriv); + return 0; } module_usb_serial_driver(serial_drivers, id_table); diff --git a/drivers/usb/serial/io_edgeport.c b/drivers/usb/serial/io_edgeport.c index c086697..f49327d 100644 --- a/drivers/usb/serial/io_edgeport.c +++ b/drivers/usb/serial/io_edgeport.c @@ -1046,9 +1046,8 @@ static void edge_close(struct usb_serial_port *port) edge_port->closePending = true; - if ((!edge_serial->is_epic) || - ((edge_serial->is_epic) && - (edge_serial->epic_descriptor.Supports.IOSPChase))) { + if (!edge_serial->is_epic || + edge_serial->epic_descriptor.Supports.IOSPChase) { /* flush and chase */ edge_port->chaseResponsePending = true; @@ -1061,9 +1060,8 @@ static void edge_close(struct usb_serial_port *port) edge_port->chaseResponsePending = false; } - if ((!edge_serial->is_epic) || - ((edge_serial->is_epic) && - (edge_serial->epic_descriptor.Supports.IOSPClose))) { + if (!edge_serial->is_epic || + edge_serial->epic_descriptor.Supports.IOSPClose) { /* close the port */ dev_dbg(&port->dev, "%s - Sending IOSP_CMD_CLOSE_PORT\n", __func__); send_iosp_ext_cmd(edge_port, IOSP_CMD_CLOSE_PORT, 0); @@ -1612,9 +1610,8 @@ static void edge_break(struct tty_struct *tty, int break_state) struct edgeport_serial *edge_serial = usb_get_serial_data(port->serial); int status; - if ((!edge_serial->is_epic) || - ((edge_serial->is_epic) && - (edge_serial->epic_descriptor.Supports.IOSPChase))) { + if (!edge_serial->is_epic || + edge_serial->epic_descriptor.Supports.IOSPChase) { /* flush and chase */ edge_port->chaseResponsePending = true; @@ -1628,9 +1625,8 @@ static void edge_break(struct tty_struct *tty, int break_state) } } - if ((!edge_serial->is_epic) || - ((edge_serial->is_epic) && - (edge_serial->epic_descriptor.Supports.IOSPSetClrBreak))) { + if (!edge_serial->is_epic || + edge_serial->epic_descriptor.Supports.IOSPSetClrBreak) { if (break_state == -1) { dev_dbg(&port->dev, "%s - Sending IOSP_CMD_SET_BREAK\n", __func__); status = send_iosp_ext_cmd(edge_port, @@ -2465,9 +2461,8 @@ static void change_port_settings(struct tty_struct *tty, unsigned char stop_char = STOP_CHAR(tty); unsigned char start_char = START_CHAR(tty); - if ((!edge_serial->is_epic) || - ((edge_serial->is_epic) && - (edge_serial->epic_descriptor.Supports.IOSPSetXChar))) { + if (!edge_serial->is_epic || + edge_serial->epic_descriptor.Supports.IOSPSetXChar) { send_iosp_ext_cmd(edge_port, IOSP_CMD_SET_XON_CHAR, start_char); send_iosp_ext_cmd(edge_port, @@ -2494,13 +2489,11 @@ static void change_port_settings(struct tty_struct *tty, } /* Set flow control to the configured value */ - if ((!edge_serial->is_epic) || - ((edge_serial->is_epic) && - (edge_serial->epic_descriptor.Supports.IOSPSetRxFlow))) + if (!edge_serial->is_epic || + edge_serial->epic_descriptor.Supports.IOSPSetRxFlow) send_iosp_ext_cmd(edge_port, IOSP_CMD_SET_RX_FLOW, rxFlow); - if ((!edge_serial->is_epic) || - ((edge_serial->is_epic) && - (edge_serial->epic_descriptor.Supports.IOSPSetTxFlow))) + if (!edge_serial->is_epic || + edge_serial->epic_descriptor.Supports.IOSPSetTxFlow) send_iosp_ext_cmd(edge_port, IOSP_CMD_SET_TX_FLOW, txFlow); diff --git a/drivers/usb/serial/mos7840.c b/drivers/usb/serial/mos7840.c index 8ac9b55..2c69bfc 100644 --- a/drivers/usb/serial/mos7840.c +++ b/drivers/usb/serial/mos7840.c @@ -635,7 +635,7 @@ static void mos7840_interrupt_callback(struct urb *urb) * Byte 4 IIR Port 4 (port.number is 3) * Byte 5 FIFO status for both */ - if (length && length > 5) { + if (length > 5) { dev_dbg(&urb->dev->dev, "%s", "Wrong data !!!\n"); return; } diff --git a/drivers/usb/serial/mxu11x0.c b/drivers/usb/serial/mxu11x0.c new file mode 100644 index 0000000..e3c3f57c --- /dev/null +++ b/drivers/usb/serial/mxu11x0.c @@ -0,0 +1,986 @@ +/* + * USB Moxa UPORT 11x0 Serial Driver + * + * Copyright (C) 2007 MOXA Technologies Co., Ltd. + * Copyright (C) 2015 Mathieu Othacehe <m.othacehe@gmail.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * + * Supports the following Moxa USB to serial converters: + * UPort 1110, 1 port RS-232 USB to Serial Hub. + * UPort 1130, 1 port RS-422/485 USB to Serial Hub. + * UPort 1130I, 1 port RS-422/485 USB to Serial Hub with isolation + * protection. + * UPort 1150, 1 port RS-232/422/485 USB to Serial Hub. + * UPort 1150I, 1 port RS-232/422/485 USB to Serial Hub with isolation + * protection. + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/firmware.h> +#include <linux/jiffies.h> +#include <linux/serial.h> +#include <linux/serial_reg.h> +#include <linux/slab.h> +#include <linux/spinlock.h> +#include <linux/mutex.h> +#include <linux/tty.h> +#include <linux/tty_driver.h> +#include <linux/tty_flip.h> +#include <linux/uaccess.h> +#include <linux/usb.h> +#include <linux/usb/serial.h> + +/* Vendor and product ids */ +#define MXU1_VENDOR_ID 0x110a +#define MXU1_1110_PRODUCT_ID 0x1110 +#define MXU1_1130_PRODUCT_ID 0x1130 +#define MXU1_1150_PRODUCT_ID 0x1150 +#define MXU1_1151_PRODUCT_ID 0x1151 +#define MXU1_1131_PRODUCT_ID 0x1131 + +/* Commands */ +#define MXU1_GET_VERSION 0x01 +#define MXU1_GET_PORT_STATUS 0x02 +#define MXU1_GET_PORT_DEV_INFO 0x03 +#define MXU1_GET_CONFIG 0x04 +#define MXU1_SET_CONFIG 0x05 +#define MXU1_OPEN_PORT 0x06 +#define MXU1_CLOSE_PORT 0x07 +#define MXU1_START_PORT 0x08 +#define MXU1_STOP_PORT 0x09 +#define MXU1_TEST_PORT 0x0A +#define MXU1_PURGE_PORT 0x0B +#define MXU1_RESET_EXT_DEVICE 0x0C +#define MXU1_GET_OUTQUEUE 0x0D +#define MXU1_WRITE_DATA 0x80 +#define MXU1_READ_DATA 0x81 +#define MXU1_REQ_TYPE_CLASS 0x82 + +/* Module identifiers */ +#define MXU1_I2C_PORT 0x01 +#define MXU1_IEEE1284_PORT 0x02 +#define MXU1_UART1_PORT 0x03 +#define MXU1_UART2_PORT 0x04 +#define MXU1_RAM_PORT 0x05 + +/* Modem status */ +#define MXU1_MSR_DELTA_CTS 0x01 +#define MXU1_MSR_DELTA_DSR 0x02 +#define MXU1_MSR_DELTA_RI 0x04 +#define MXU1_MSR_DELTA_CD 0x08 +#define MXU1_MSR_CTS 0x10 +#define MXU1_MSR_DSR 0x20 +#define MXU1_MSR_RI 0x40 +#define MXU1_MSR_CD 0x80 +#define MXU1_MSR_DELTA_MASK 0x0F +#define MXU1_MSR_MASK 0xF0 + +/* Line status */ +#define MXU1_LSR_OVERRUN_ERROR 0x01 +#define MXU1_LSR_PARITY_ERROR 0x02 +#define MXU1_LSR_FRAMING_ERROR 0x04 +#define MXU1_LSR_BREAK 0x08 +#define MXU1_LSR_ERROR 0x0F +#define MXU1_LSR_RX_FULL 0x10 +#define MXU1_LSR_TX_EMPTY 0x20 + +/* Modem control */ +#define MXU1_MCR_LOOP 0x04 +#define MXU1_MCR_DTR 0x10 +#define MXU1_MCR_RTS 0x20 + +/* Mask settings */ +#define MXU1_UART_ENABLE_RTS_IN 0x0001 +#define MXU1_UART_DISABLE_RTS 0x0002 +#define MXU1_UART_ENABLE_PARITY_CHECKING 0x0008 +#define MXU1_UART_ENABLE_DSR_OUT 0x0010 +#define MXU1_UART_ENABLE_CTS_OUT 0x0020 +#define MXU1_UART_ENABLE_X_OUT 0x0040 +#define MXU1_UART_ENABLE_XA_OUT 0x0080 +#define MXU1_UART_ENABLE_X_IN 0x0100 +#define MXU1_UART_ENABLE_DTR_IN 0x0800 +#define MXU1_UART_DISABLE_DTR 0x1000 +#define MXU1_UART_ENABLE_MS_INTS 0x2000 +#define MXU1_UART_ENABLE_AUTO_START_DMA 0x4000 +#define MXU1_UART_SEND_BREAK_SIGNAL 0x8000 + +/* Parity */ +#define MXU1_UART_NO_PARITY 0x00 +#define MXU1_UART_ODD_PARITY 0x01 +#define MXU1_UART_EVEN_PARITY 0x02 +#define MXU1_UART_MARK_PARITY 0x03 +#define MXU1_UART_SPACE_PARITY 0x04 + +/* Stop bits */ +#define MXU1_UART_1_STOP_BITS 0x00 +#define MXU1_UART_1_5_STOP_BITS 0x01 +#define MXU1_UART_2_STOP_BITS 0x02 + +/* Bits per character */ +#define MXU1_UART_5_DATA_BITS 0x00 +#define MXU1_UART_6_DATA_BITS 0x01 +#define MXU1_UART_7_DATA_BITS 0x02 +#define MXU1_UART_8_DATA_BITS 0x03 + +/* Operation modes */ +#define MXU1_UART_232 0x00 +#define MXU1_UART_485_RECEIVER_DISABLED 0x01 +#define MXU1_UART_485_RECEIVER_ENABLED 0x02 + +/* Pipe transfer mode and timeout */ +#define MXU1_PIPE_MODE_CONTINUOUS 0x01 +#define MXU1_PIPE_MODE_MASK 0x03 +#define MXU1_PIPE_TIMEOUT_MASK 0x7C +#define MXU1_PIPE_TIMEOUT_ENABLE 0x80 + +/* Config struct */ +struct mxu1_uart_config { + __be16 wBaudRate; + __be16 wFlags; + u8 bDataBits; + u8 bParity; + u8 bStopBits; + char cXon; + char cXoff; + u8 bUartMode; +} __packed; + +/* Purge modes */ +#define MXU1_PURGE_OUTPUT 0x00 +#define MXU1_PURGE_INPUT 0x80 + +/* Read/Write data */ +#define MXU1_RW_DATA_ADDR_SFR 0x10 +#define MXU1_RW_DATA_ADDR_IDATA 0x20 +#define MXU1_RW_DATA_ADDR_XDATA 0x30 +#define MXU1_RW_DATA_ADDR_CODE 0x40 +#define MXU1_RW_DATA_ADDR_GPIO 0x50 +#define MXU1_RW_DATA_ADDR_I2C 0x60 +#define MXU1_RW_DATA_ADDR_FLASH 0x70 +#define MXU1_RW_DATA_ADDR_DSP 0x80 + +#define MXU1_RW_DATA_UNSPECIFIED 0x00 +#define MXU1_RW_DATA_BYTE 0x01 +#define MXU1_RW_DATA_WORD 0x02 +#define MXU1_RW_DATA_DOUBLE_WORD 0x04 + +struct mxu1_write_data_bytes { + u8 bAddrType; + u8 bDataType; + u8 bDataCounter; + __be16 wBaseAddrHi; + __be16 wBaseAddrLo; + u8 bData[0]; +} __packed; + +/* Interrupt codes */ +#define MXU1_CODE_HARDWARE_ERROR 0xFF +#define MXU1_CODE_DATA_ERROR 0x03 +#define MXU1_CODE_MODEM_STATUS 0x04 + +static inline int mxu1_get_func_from_code(unsigned char code) +{ + return code & 0x0f; +} + +/* Download firmware max packet size */ +#define MXU1_DOWNLOAD_MAX_PACKET_SIZE 64 + +/* Firmware image header */ +struct mxu1_firmware_header { + __le16 wLength; + u8 bCheckSum; +} __packed; + +#define MXU1_UART_BASE_ADDR 0xFFA0 +#define MXU1_UART_OFFSET_MCR 0x0004 + +#define MXU1_BAUD_BASE 923077 + +#define MXU1_TRANSFER_TIMEOUT 2 +#define MXU1_DOWNLOAD_TIMEOUT 1000 +#define MXU1_DEFAULT_CLOSING_WAIT 4000 /* in .01 secs */ + +struct mxu1_port { + u8 msr; + u8 mcr; + u8 uart_mode; + spinlock_t spinlock; /* Protects msr */ + struct mutex mutex; /* Protects mcr */ + bool send_break; +}; + +struct mxu1_device { + u16 mxd_model; +}; + +static const struct usb_device_id mxu1_idtable[] = { + { USB_DEVICE(MXU1_VENDOR_ID, MXU1_1110_PRODUCT_ID) }, + { USB_DEVICE(MXU1_VENDOR_ID, MXU1_1130_PRODUCT_ID) }, + { USB_DEVICE(MXU1_VENDOR_ID, MXU1_1150_PRODUCT_ID) }, + { USB_DEVICE(MXU1_VENDOR_ID, MXU1_1151_PRODUCT_ID) }, + { USB_DEVICE(MXU1_VENDOR_ID, MXU1_1131_PRODUCT_ID) }, + { } +}; + +MODULE_DEVICE_TABLE(usb, mxu1_idtable); + +/* Write the given buffer out to the control pipe. */ +static int mxu1_send_ctrl_data_urb(struct usb_serial *serial, + u8 request, + u16 value, u16 index, + void *data, size_t size) +{ + int status; + + status = usb_control_msg(serial->dev, + usb_sndctrlpipe(serial->dev, 0), + request, + (USB_DIR_OUT | USB_TYPE_VENDOR | + USB_RECIP_DEVICE), value, index, + data, size, + USB_CTRL_SET_TIMEOUT); + if (status < 0) { + dev_err(&serial->interface->dev, + "%s - usb_control_msg failed: %d\n", + __func__, status); + return status; + } + + if (status != size) { + dev_err(&serial->interface->dev, + "%s - short write (%d / %zd)\n", + __func__, status, size); + return -EIO; + } + + return 0; +} + +/* Send a vendor request without any data */ +static int mxu1_send_ctrl_urb(struct usb_serial *serial, + u8 request, u16 value, u16 index) +{ + return mxu1_send_ctrl_data_urb(serial, request, value, index, + NULL, 0); +} + +static int mxu1_download_firmware(struct usb_serial *serial, + const struct firmware *fw_p) +{ + int status = 0; + int buffer_size; + int pos; + int len; + int done; + u8 cs = 0; + u8 *buffer; + struct usb_device *dev = serial->dev; + struct mxu1_firmware_header *header; + unsigned int pipe; + + pipe = usb_sndbulkpipe(dev, serial->port[0]->bulk_out_endpointAddress); + + buffer_size = fw_p->size + sizeof(*header); + buffer = kmalloc(buffer_size, GFP_KERNEL); + if (!buffer) + return -ENOMEM; + + memcpy(buffer, fw_p->data, fw_p->size); + memset(buffer + fw_p->size, 0xff, buffer_size - fw_p->size); + + for (pos = sizeof(*header); pos < buffer_size; pos++) + cs = (u8)(cs + buffer[pos]); + + header = (struct mxu1_firmware_header *)buffer; + header->wLength = cpu_to_le16(buffer_size - sizeof(*header)); + header->bCheckSum = cs; + + dev_dbg(&dev->dev, "%s - downloading firmware\n", __func__); + + for (pos = 0; pos < buffer_size; pos += done) { + len = min(buffer_size - pos, MXU1_DOWNLOAD_MAX_PACKET_SIZE); + + status = usb_bulk_msg(dev, pipe, buffer + pos, len, &done, + MXU1_DOWNLOAD_TIMEOUT); + if (status) + break; + } + + kfree(buffer); + + if (status) { + dev_err(&dev->dev, "failed to download firmware: %d\n", status); + return status; + } + + msleep_interruptible(100); + usb_reset_device(dev); + + dev_dbg(&dev->dev, "%s - download successful\n", __func__); + + return 0; +} + +static int mxu1_port_probe(struct usb_serial_port *port) +{ + struct mxu1_port *mxport; + struct mxu1_device *mxdev; + + if (!port->interrupt_in_urb) { + dev_err(&port->dev, "no interrupt urb\n"); + return -ENODEV; + } + + mxport = kzalloc(sizeof(struct mxu1_port), GFP_KERNEL); + if (!mxport) + return -ENOMEM; + + spin_lock_init(&mxport->spinlock); + mutex_init(&mxport->mutex); + + mxdev = usb_get_serial_data(port->serial); + + switch (mxdev->mxd_model) { + case MXU1_1110_PRODUCT_ID: + case MXU1_1150_PRODUCT_ID: + case MXU1_1151_PRODUCT_ID: + mxport->uart_mode = MXU1_UART_232; + break; + case MXU1_1130_PRODUCT_ID: + case MXU1_1131_PRODUCT_ID: + mxport->uart_mode = MXU1_UART_485_RECEIVER_DISABLED; + break; + } + + usb_set_serial_port_data(port, mxport); + + port->port.closing_wait = + msecs_to_jiffies(MXU1_DEFAULT_CLOSING_WAIT * 10); + port->port.drain_delay = 1; + + return 0; +} + +static int mxu1_startup(struct usb_serial *serial) +{ + struct mxu1_device *mxdev; + struct usb_device *dev = serial->dev; + struct usb_host_interface *cur_altsetting; + char fw_name[32]; + const struct firmware *fw_p = NULL; + int err; + + dev_dbg(&serial->interface->dev, "%s - product 0x%04X, num configurations %d, configuration value %d\n", + __func__, le16_to_cpu(dev->descriptor.idProduct), + dev->descriptor.bNumConfigurations, + dev->actconfig->desc.bConfigurationValue); + + /* create device structure */ + mxdev = kzalloc(sizeof(struct mxu1_device), GFP_KERNEL); + if (!mxdev) + return -ENOMEM; + + usb_set_serial_data(serial, mxdev); + + mxdev->mxd_model = le16_to_cpu(dev->descriptor.idProduct); + + cur_altsetting = serial->interface->cur_altsetting; + + /* if we have only 1 configuration, download firmware */ + if (cur_altsetting->desc.bNumEndpoints == 1) { + + snprintf(fw_name, + sizeof(fw_name), + "moxa/moxa-%04x.fw", + mxdev->mxd_model); + + err = request_firmware(&fw_p, fw_name, &serial->interface->dev); + if (err) { + dev_err(&serial->interface->dev, "failed to request firmware: %d\n", + err); + goto err_free_mxdev; + } + + err = mxu1_download_firmware(serial, fw_p); + if (err) + goto err_release_firmware; + + /* device is being reset */ + err = -ENODEV; + goto err_release_firmware; + } + + return 0; + +err_release_firmware: + release_firmware(fw_p); +err_free_mxdev: + kfree(mxdev); + + return err; +} + +static int mxu1_write_byte(struct usb_serial_port *port, u32 addr, + u8 mask, u8 byte) +{ + int status; + size_t size; + struct mxu1_write_data_bytes *data; + + dev_dbg(&port->dev, "%s - addr 0x%08X, mask 0x%02X, byte 0x%02X\n", + __func__, addr, mask, byte); + + size = sizeof(struct mxu1_write_data_bytes) + 2; + data = kzalloc(size, GFP_KERNEL); + if (!data) + return -ENOMEM; + + data->bAddrType = MXU1_RW_DATA_ADDR_XDATA; + data->bDataType = MXU1_RW_DATA_BYTE; + data->bDataCounter = 1; + data->wBaseAddrHi = cpu_to_be16(addr >> 16); + data->wBaseAddrLo = cpu_to_be16(addr); + data->bData[0] = mask; + data->bData[1] = byte; + + status = mxu1_send_ctrl_data_urb(port->serial, MXU1_WRITE_DATA, 0, + MXU1_RAM_PORT, data, size); + if (status < 0) + dev_err(&port->dev, "%s - failed: %d\n", __func__, status); + + kfree(data); + + return status; +} + +static int mxu1_set_mcr(struct usb_serial_port *port, unsigned int mcr) +{ + int status; + + status = mxu1_write_byte(port, + MXU1_UART_BASE_ADDR + MXU1_UART_OFFSET_MCR, + MXU1_MCR_RTS | MXU1_MCR_DTR | MXU1_MCR_LOOP, + mcr); + return status; +} + +static void mxu1_set_termios(struct tty_struct *tty, + struct usb_serial_port *port, + struct ktermios *old_termios) +{ + struct mxu1_port *mxport = usb_get_serial_port_data(port); + struct mxu1_uart_config *config; + tcflag_t cflag, iflag; + speed_t baud; + int status; + unsigned int mcr; + + cflag = tty->termios.c_cflag; + iflag = tty->termios.c_iflag; + + if (old_termios && + !tty_termios_hw_change(&tty->termios, old_termios) && + tty->termios.c_iflag == old_termios->c_iflag) { + dev_dbg(&port->dev, "%s - nothing to change\n", __func__); + return; + } + + dev_dbg(&port->dev, + "%s - cflag 0x%08x, iflag 0x%08x\n", __func__, cflag, iflag); + + if (old_termios) { + dev_dbg(&port->dev, "%s - old cflag 0x%08x, old iflag 0x%08x\n", + __func__, + old_termios->c_cflag, + old_termios->c_iflag); + } + + config = kzalloc(sizeof(*config), GFP_KERNEL); + if (!config) + return; + + /* these flags must be set */ + config->wFlags |= MXU1_UART_ENABLE_MS_INTS; + config->wFlags |= MXU1_UART_ENABLE_AUTO_START_DMA; + if (mxport->send_break) + config->wFlags |= MXU1_UART_SEND_BREAK_SIGNAL; + config->bUartMode = mxport->uart_mode; + + switch (C_CSIZE(tty)) { + case CS5: + config->bDataBits = MXU1_UART_5_DATA_BITS; + break; + case CS6: + config->bDataBits = MXU1_UART_6_DATA_BITS; + break; + case CS7: + config->bDataBits = MXU1_UART_7_DATA_BITS; + break; + default: + case CS8: + config->bDataBits = MXU1_UART_8_DATA_BITS; + break; + } + + if (C_PARENB(tty)) { + config->wFlags |= MXU1_UART_ENABLE_PARITY_CHECKING; + if (C_CMSPAR(tty)) { + if (C_PARODD(tty)) + config->bParity = MXU1_UART_MARK_PARITY; + else + config->bParity = MXU1_UART_SPACE_PARITY; + } else { + if (C_PARODD(tty)) + config->bParity = MXU1_UART_ODD_PARITY; + else + config->bParity = MXU1_UART_EVEN_PARITY; + } + } else { + config->bParity = MXU1_UART_NO_PARITY; + } + + if (C_CSTOPB(tty)) + config->bStopBits = MXU1_UART_2_STOP_BITS; + else + config->bStopBits = MXU1_UART_1_STOP_BITS; + + if (C_CRTSCTS(tty)) { + /* RTS flow control must be off to drop RTS for baud rate B0 */ + if (C_BAUD(tty) != B0) + config->wFlags |= MXU1_UART_ENABLE_RTS_IN; + config->wFlags |= MXU1_UART_ENABLE_CTS_OUT; + } + + if (I_IXOFF(tty) || I_IXON(tty)) { + config->cXon = START_CHAR(tty); + config->cXoff = STOP_CHAR(tty); + + if (I_IXOFF(tty)) + config->wFlags |= MXU1_UART_ENABLE_X_IN; + + if (I_IXON(tty)) + config->wFlags |= MXU1_UART_ENABLE_X_OUT; + } + + baud = tty_get_baud_rate(tty); + if (!baud) + baud = 9600; + config->wBaudRate = MXU1_BAUD_BASE / baud; + + dev_dbg(&port->dev, "%s - BaudRate=%d, wBaudRate=%d, wFlags=0x%04X, bDataBits=%d, bParity=%d, bStopBits=%d, cXon=%d, cXoff=%d, bUartMode=%d\n", + __func__, baud, config->wBaudRate, config->wFlags, + config->bDataBits, config->bParity, config->bStopBits, + config->cXon, config->cXoff, config->bUartMode); + + cpu_to_be16s(&config->wBaudRate); + cpu_to_be16s(&config->wFlags); + + status = mxu1_send_ctrl_data_urb(port->serial, MXU1_SET_CONFIG, 0, + MXU1_UART1_PORT, config, + sizeof(*config)); + if (status) + dev_err(&port->dev, "cannot set config: %d\n", status); + + mutex_lock(&mxport->mutex); + mcr = mxport->mcr; + + if (C_BAUD(tty) == B0) + mcr &= ~(MXU1_MCR_DTR | MXU1_MCR_RTS); + else if (old_termios && (old_termios->c_cflag & CBAUD) == B0) + mcr |= MXU1_MCR_DTR | MXU1_MCR_RTS; + + status = mxu1_set_mcr(port, mcr); + if (status) + dev_err(&port->dev, "cannot set modem control: %d\n", status); + else + mxport->mcr = mcr; + + mutex_unlock(&mxport->mutex); + + kfree(config); +} + +static int mxu1_get_serial_info(struct usb_serial_port *port, + struct serial_struct __user *ret_arg) +{ + struct serial_struct ret_serial; + unsigned cwait; + + if (!ret_arg) + return -EFAULT; + + cwait = port->port.closing_wait; + if (cwait != ASYNC_CLOSING_WAIT_NONE) + cwait = jiffies_to_msecs(cwait) / 10; + + memset(&ret_serial, 0, sizeof(ret_serial)); + + ret_serial.type = PORT_16550A; + ret_serial.line = port->minor; + ret_serial.port = 0; + ret_serial.xmit_fifo_size = port->bulk_out_size; + ret_serial.baud_base = MXU1_BAUD_BASE; + ret_serial.close_delay = 5*HZ; + ret_serial.closing_wait = cwait; + + if (copy_to_user(ret_arg, &ret_serial, sizeof(*ret_arg))) + return -EFAULT; + + return 0; +} + + +static int mxu1_set_serial_info(struct usb_serial_port *port, + struct serial_struct __user *new_arg) +{ + struct serial_struct new_serial; + unsigned cwait; + + if (copy_from_user(&new_serial, new_arg, sizeof(new_serial))) + return -EFAULT; + + cwait = new_serial.closing_wait; + if (cwait != ASYNC_CLOSING_WAIT_NONE) + cwait = msecs_to_jiffies(10 * new_serial.closing_wait); + + port->port.closing_wait = cwait; + + return 0; +} + +static int mxu1_ioctl(struct tty_struct *tty, + unsigned int cmd, unsigned long arg) +{ + struct usb_serial_port *port = tty->driver_data; + + switch (cmd) { + case TIOCGSERIAL: + return mxu1_get_serial_info(port, + (struct serial_struct __user *)arg); + case TIOCSSERIAL: + return mxu1_set_serial_info(port, + (struct serial_struct __user *)arg); + } + + return -ENOIOCTLCMD; +} + +static int mxu1_tiocmget(struct tty_struct *tty) +{ + struct usb_serial_port *port = tty->driver_data; + struct mxu1_port *mxport = usb_get_serial_port_data(port); + unsigned int result; + unsigned int msr; + unsigned int mcr; + unsigned long flags; + + mutex_lock(&mxport->mutex); + spin_lock_irqsave(&mxport->spinlock, flags); + + msr = mxport->msr; + mcr = mxport->mcr; + + spin_unlock_irqrestore(&mxport->spinlock, flags); + mutex_unlock(&mxport->mutex); + + result = ((mcr & MXU1_MCR_DTR) ? TIOCM_DTR : 0) | + ((mcr & MXU1_MCR_RTS) ? TIOCM_RTS : 0) | + ((mcr & MXU1_MCR_LOOP) ? TIOCM_LOOP : 0) | + ((msr & MXU1_MSR_CTS) ? TIOCM_CTS : 0) | + ((msr & MXU1_MSR_CD) ? TIOCM_CAR : 0) | + ((msr & MXU1_MSR_RI) ? TIOCM_RI : 0) | + ((msr & MXU1_MSR_DSR) ? TIOCM_DSR : 0); + + dev_dbg(&port->dev, "%s - 0x%04X\n", __func__, result); + + return result; +} + +static int mxu1_tiocmset(struct tty_struct *tty, + unsigned int set, unsigned int clear) +{ + struct usb_serial_port *port = tty->driver_data; + struct mxu1_port *mxport = usb_get_serial_port_data(port); + int err; + unsigned int mcr; + + mutex_lock(&mxport->mutex); + mcr = mxport->mcr; + + if (set & TIOCM_RTS) + mcr |= MXU1_MCR_RTS; + if (set & TIOCM_DTR) + mcr |= MXU1_MCR_DTR; + if (set & TIOCM_LOOP) + mcr |= MXU1_MCR_LOOP; + + if (clear & TIOCM_RTS) + mcr &= ~MXU1_MCR_RTS; + if (clear & TIOCM_DTR) + mcr &= ~MXU1_MCR_DTR; + if (clear & TIOCM_LOOP) + mcr &= ~MXU1_MCR_LOOP; + + err = mxu1_set_mcr(port, mcr); + if (!err) + mxport->mcr = mcr; + + mutex_unlock(&mxport->mutex); + + return err; +} + +static void mxu1_break(struct tty_struct *tty, int break_state) +{ + struct usb_serial_port *port = tty->driver_data; + struct mxu1_port *mxport = usb_get_serial_port_data(port); + + if (break_state == -1) + mxport->send_break = true; + else + mxport->send_break = false; + + mxu1_set_termios(tty, port, NULL); +} + +static int mxu1_open(struct tty_struct *tty, struct usb_serial_port *port) +{ + struct mxu1_port *mxport = usb_get_serial_port_data(port); + struct usb_serial *serial = port->serial; + int status; + u16 open_settings; + + open_settings = (MXU1_PIPE_MODE_CONTINUOUS | + MXU1_PIPE_TIMEOUT_ENABLE | + (MXU1_TRANSFER_TIMEOUT << 2)); + + mxport->msr = 0; + + status = usb_submit_urb(port->interrupt_in_urb, GFP_KERNEL); + if (status) { + dev_err(&port->dev, "failed to submit interrupt urb: %d\n", + status); + return status; + } + + if (tty) + mxu1_set_termios(tty, port, NULL); + + status = mxu1_send_ctrl_urb(serial, MXU1_OPEN_PORT, + open_settings, MXU1_UART1_PORT); + if (status) { + dev_err(&port->dev, "cannot send open command: %d\n", status); + goto unlink_int_urb; + } + + status = mxu1_send_ctrl_urb(serial, MXU1_START_PORT, + 0, MXU1_UART1_PORT); + if (status) { + dev_err(&port->dev, "cannot send start command: %d\n", status); + goto unlink_int_urb; + } + + status = mxu1_send_ctrl_urb(serial, MXU1_PURGE_PORT, + MXU1_PURGE_INPUT, MXU1_UART1_PORT); + if (status) { + dev_err(&port->dev, "cannot clear input buffers: %d\n", + status); + + goto unlink_int_urb; + } + + status = mxu1_send_ctrl_urb(serial, MXU1_PURGE_PORT, + MXU1_PURGE_OUTPUT, MXU1_UART1_PORT); + if (status) { + dev_err(&port->dev, "cannot clear output buffers: %d\n", + status); + + goto unlink_int_urb; + } + + /* + * reset the data toggle on the bulk endpoints to work around bug in + * host controllers where things get out of sync some times + */ + usb_clear_halt(serial->dev, port->write_urb->pipe); + usb_clear_halt(serial->dev, port->read_urb->pipe); + + if (tty) + mxu1_set_termios(tty, port, NULL); + + status = mxu1_send_ctrl_urb(serial, MXU1_OPEN_PORT, + open_settings, MXU1_UART1_PORT); + if (status) { + dev_err(&port->dev, "cannot send open command: %d\n", status); + goto unlink_int_urb; + } + + status = mxu1_send_ctrl_urb(serial, MXU1_START_PORT, + 0, MXU1_UART1_PORT); + if (status) { + dev_err(&port->dev, "cannot send start command: %d\n", status); + goto unlink_int_urb; + } + + status = usb_serial_generic_open(tty, port); + if (status) + goto unlink_int_urb; + + return 0; + +unlink_int_urb: + usb_kill_urb(port->interrupt_in_urb); + + return status; +} + +static void mxu1_close(struct usb_serial_port *port) +{ + int status; + + usb_serial_generic_close(port); + usb_kill_urb(port->interrupt_in_urb); + + status = mxu1_send_ctrl_urb(port->serial, MXU1_CLOSE_PORT, + 0, MXU1_UART1_PORT); + if (status) { + dev_err(&port->dev, "failed to send close port command: %d\n", + status); + } +} + +static void mxu1_handle_new_msr(struct usb_serial_port *port, u8 msr) +{ + struct mxu1_port *mxport = usb_get_serial_port_data(port); + struct async_icount *icount; + unsigned long flags; + + dev_dbg(&port->dev, "%s - msr 0x%02X\n", __func__, msr); + + spin_lock_irqsave(&mxport->spinlock, flags); + mxport->msr = msr & MXU1_MSR_MASK; + spin_unlock_irqrestore(&mxport->spinlock, flags); + + if (msr & MXU1_MSR_DELTA_MASK) { + icount = &port->icount; + if (msr & MXU1_MSR_DELTA_CTS) + icount->cts++; + if (msr & MXU1_MSR_DELTA_DSR) + icount->dsr++; + if (msr & MXU1_MSR_DELTA_CD) + icount->dcd++; + if (msr & MXU1_MSR_DELTA_RI) + icount->rng++; + + wake_up_interruptible(&port->port.delta_msr_wait); + } +} + +static void mxu1_interrupt_callback(struct urb *urb) +{ + struct usb_serial_port *port = urb->context; + unsigned char *data = urb->transfer_buffer; + int length = urb->actual_length; + int function; + int status; + u8 msr; + + switch (urb->status) { + case 0: + break; + case -ECONNRESET: + case -ENOENT: + case -ESHUTDOWN: + dev_dbg(&port->dev, "%s - urb shutting down: %d\n", + __func__, urb->status); + return; + default: + dev_dbg(&port->dev, "%s - nonzero urb status: %d\n", + __func__, urb->status); + goto exit; + } + + if (length != 2) { + dev_dbg(&port->dev, "%s - bad packet size: %d\n", + __func__, length); + goto exit; + } + + if (data[0] == MXU1_CODE_HARDWARE_ERROR) { + dev_err(&port->dev, "hardware error: %d\n", data[1]); + goto exit; + } + + function = mxu1_get_func_from_code(data[0]); + + dev_dbg(&port->dev, "%s - function %d, data 0x%02X\n", + __func__, function, data[1]); + + switch (function) { + case MXU1_CODE_DATA_ERROR: + dev_dbg(&port->dev, "%s - DATA ERROR, data 0x%02X\n", + __func__, data[1]); + break; + + case MXU1_CODE_MODEM_STATUS: + msr = data[1]; + mxu1_handle_new_msr(port, msr); + break; + + default: + dev_err(&port->dev, "unknown interrupt code: 0x%02X\n", + data[1]); + break; + } + +exit: + status = usb_submit_urb(urb, GFP_ATOMIC); + if (status) { + dev_err(&port->dev, "resubmit interrupt urb failed: %d\n", + status); + } +} + +static struct usb_serial_driver mxu11x0_device = { + .driver = { + .owner = THIS_MODULE, + .name = "mxu11x0", + }, + .description = "MOXA UPort 11x0", + .id_table = mxu1_idtable, + .num_ports = 1, + .port_probe = mxu1_port_probe, + .attach = mxu1_startup, + .open = mxu1_open, + .close = mxu1_close, + .ioctl = mxu1_ioctl, + .set_termios = mxu1_set_termios, + .tiocmget = mxu1_tiocmget, + .tiocmset = mxu1_tiocmset, + .tiocmiwait = usb_serial_generic_tiocmiwait, + .get_icount = usb_serial_generic_get_icount, + .break_ctl = mxu1_break, + .read_int_callback = mxu1_interrupt_callback, +}; + +static struct usb_serial_driver *const serial_drivers[] = { + &mxu11x0_device, NULL +}; + +module_usb_serial_driver(serial_drivers, mxu1_idtable); + +MODULE_AUTHOR("Mathieu Othacehe <m.othacehe@gmail.com>"); +MODULE_DESCRIPTION("MOXA UPort 11x0 USB to Serial Hub Driver"); +MODULE_LICENSE("GPL"); +MODULE_FIRMWARE("moxa/moxa-1110.fw"); +MODULE_FIRMWARE("moxa/moxa-1130.fw"); +MODULE_FIRMWARE("moxa/moxa-1131.fw"); +MODULE_FIRMWARE("moxa/moxa-1150.fw"); +MODULE_FIRMWARE("moxa/moxa-1151.fw"); |