arm64: dts: apq8016-sbc: Add HDMI display support

The APQ8016-sbc provides a HDMI output. The APQ8016 display block only
provides a MIPI DSI output. So, the board has a ADV7533 DSI to HDMI
encoder chip that sits between the DSI PHY output and the HDMI
connector.

Add the ADV7533 DT node under its I2C control bus, and tie the DSI
output port to the ADV7533's input port.

Cc: Andy Gross <andy.gross@linaro.org>
Cc: Rob Herring <robh@kernel.org>
Cc: devicetree@vger.kernel.org

Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>

2 files changed, 130 insertions, 0 deletions

diff --git a/arch/arm64/boot/dts/qcom/apq8016-sbc-soc-pins.dtsi b/arch/arm64/boot/dts/qcom/apq8016-sbc-soc-pins.dtsi
index ee828a8..e1e6c6b 100644
--- a/arch/arm64/boot/dts/qcom/apq8016-sbc-soc-pins.dtsi
+++ b/arch/arm64/boot/dts/qcom/apq8016-sbc-soc-pins.dtsi
@@ -24,4 +24,52 @@
 			bias-pull-up;
 		};
 	};
+
+	adv7533_int_active: adv533_int_active {
+		pinmux {
+			function = "gpio";
+			pins = "gpio31";
+		};
+		pinconf {
+			pins = "gpio31";
+			drive-strength = <16>;
+			bias-disable;
+		};
+	};
+
+	adv7533_int_suspend: adv7533_int_suspend {
+		pinmux {
+			function = "gpio";
+			pins = "gpio31";
+		};
+		pinconf {
+			pins = "gpio31";
+			drive-strength = <2>;
+			bias-disable;
+		};
+	};
+
+	adv7533_switch_active: adv7533_switch_active {
+		pinmux {
+			function = "gpio";
+			pins = "gpio32";
+		};
+		pinconf {
+			pins = "gpio32";
+			drive-strength = <16>;
+			bias-disable;
+		};
+	};
+
+	adv7533_switch_suspend: adv7533_switch_suspend {
+		pinmux {
+			function = "gpio";
+			pins = "gpio32";
+		};
+		pinconf {
+			pins = "gpio32";
+			drive-strength = <2>;
+			bias-disable;
+		};
+	};
 };
diff --git a/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi b/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi
index 18639bc..bb062b5 100644
--- a/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi
+++ b/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi
@@ -63,6 +63,47 @@
 		/* On High speed expansion */
 			label = "HS-I2C2";
 			status = "okay";
+
+			adv_bridge: bridge@39 {
+				status = "okay";
+
+				compatible = "adi,adv7533";
+				reg = <0x39>;
+
+				interrupt-parent = <&msmgpio>;
+				interrupts = <31 2>;
+
+				adi,dsi-lanes = <4>;
+
+				pd-gpios = <&msmgpio 32 0>;
+
+				avdd-supply = <&pm8916_l6>;
+				v1p2-supply = <&pm8916_l6>;
+				v3p3-supply = <&pm8916_l17>;
+
+				pinctrl-names = "default","sleep";
+				pinctrl-0 = <&adv7533_int_active &adv7533_switch_active>;
+				pinctrl-1 = <&adv7533_int_suspend &adv7533_switch_suspend>;
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+						adv7533_in: endpoint {
+							remote-endpoint = <&dsi0_out>;
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+						adv7533_out: endpoint {
+							remote-endpoint = <&hdmi_con>;
+						};
+					};
+				};
+			};
 		};
 
 		i2c@78ba000 {
@@ -180,6 +221,36 @@
 		lpass@07708000 {
 			status = "okay";
 		};
+
+		mdss@1a00000 {
+			status = "okay";
+
+			mdp@1a01000 {
+				status = "okay";
+			};
+
+			dsi@1a98000 {
+				status = "okay";
+
+				vdda-supply = <&pm8916_l2>;
+				vddio-supply = <&pm8916_l6>;
+
+				ports {
+					port@1 {
+						endpoint {
+							remote-endpoint = <&adv7533_in>;
+							data-lanes = <0 1 2 3>;
+						};
+					};
+				};
+			};
+
+			dsi-phy@1a98300 {
+				status = "okay";
+
+				vddio-supply = <&pm8916_l6>;
+			};
+		};
 	};
 
 	usb2513 {
@@ -194,6 +265,17 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&usb_id_default>;
 	};
+
+	hdmi-out {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con: endpoint {
+				remote-endpoint = <&adv7533_out>;
+			};
+		};
+	};
 };
 
 &smd_rpm_regulators {