diff options
author | Linus Torvalds <torvalds@linux-foundation.org> | 2013-02-26 17:31:09 (GMT) |
---|---|---|
committer | Linus Torvalds <torvalds@linux-foundation.org> | 2013-02-26 17:31:09 (GMT) |
commit | ed5dc2372dba46e0ecd08791b1a0399d313e5cff (patch) | |
tree | 571319985b59a2963fb7580c24ee2aa1696359e2 /Documentation | |
parent | 0512c04a2b5d29a33d96d315e1d14c55f5148aa7 (diff) | |
parent | 0e786102949d7461859c6ce9f39c2c8d28e42db3 (diff) | |
download | linux-ed5dc2372dba46e0ecd08791b1a0399d313e5cff.tar.xz |
Merge tag 'mmc-updates-for-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC update from Chris Ball:
"MMC highlights for 3.9:
Core:
- Support for packed commands in eMMC 4.5. (This requires a host
capability to be turned on. It increases write throughput by 20%+,
but may also increase average write latency; more testing needed.)
- Add DT bindings for capability flags.
- Add mmc_of_parse() for shared DT parsing between drivers.
Drivers:
- android-goldfish: New MMC driver for the Android Goldfish emulator.
- mvsdio: Add DT bindings, pinctrl, use slot-gpio for card detection.
- omap_hsmmc: Fix boot hangs with RPMB partitions.
- sdhci-bcm2835: New driver for controller used by Raspberry Pi.
- sdhci-esdhc-imx: Add 8-bit data, auto CMD23 support, use slot-gpio.
- sh_mmcif: Add support for eMMC DDR, bundled MMCIF IRQs.
- tmio_mmc: Add DT bindings, support for vccq regulator"
* tag 'mmc-updates-for-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (92 commits)
mmc: tegra: assume CONFIG_OF, remove platform data
mmc: add DT bindings for more MMC capability flags
mmc: tmio: add support for the VccQ regulator
mmc: tmio: remove unused and deprecated symbols
mmc: sh_mobile_sdhi: use managed resource allocations
mmc: sh_mobile_sdhi: remove unused .pdata field
mmc: tmio-mmc: parse device-tree bindings
mmc: tmio-mmc: define device-tree bindings
mmc: sh_mmcif: use mmc_of_parse() to parse standard MMC DT bindings
mmc: (cosmetic) remove "extern" from function declarations
mmc: provide a standard MMC device-tree binding parser centrally
mmc: detailed definition of CD and WP MMC line polarities in DT
mmc: sdhi, tmio: only check flags in tmio-mmc driver proper
mmc: sdhci: Fix parameter of sdhci_do_start_signal_voltage_switch()
mmc: sdhci: check voltage range only on regulators aware of voltage value
mmc: bcm2835: set SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK
mmc: support packed write command for eMMC4.5 devices
mmc: add packed command feature of eMMC4.5
mmc: rtsx: remove driving adjustment
mmc: use regulator_can_change_voltage() instead of regulator_count_voltages
...
Diffstat (limited to 'Documentation')
5 files changed, 93 insertions, 8 deletions
diff --git a/Documentation/devicetree/bindings/mmc/brcm,bcm2835-sdhci.txt b/Documentation/devicetree/bindings/mmc/brcm,bcm2835-sdhci.txt new file mode 100644 index 0000000..59476fb --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/brcm,bcm2835-sdhci.txt @@ -0,0 +1,18 @@ +Broadcom BCM2835 SDHCI controller + +This file documents differences between the core properties described +by mmc.txt and the properties that represent the BCM2835 controller. + +Required properties: +- compatible : Should be "brcm,bcm2835-sdhci". +- clocks : The clock feeding the SDHCI controller. + +Example: + +sdhci: sdhci { + compatible = "brcm,bcm2835-sdhci"; + reg = <0x7e300000 0x100>; + interrupts = <2 30>; + clocks = <&clk_mmc>; + bus-width = <4>; +}; diff --git a/Documentation/devicetree/bindings/mmc/mmc.txt b/Documentation/devicetree/bindings/mmc/mmc.txt index a591c67..85aada2 100644 --- a/Documentation/devicetree/bindings/mmc/mmc.txt +++ b/Documentation/devicetree/bindings/mmc/mmc.txt @@ -6,23 +6,45 @@ Interpreted by the OF core: - reg: Registers location and length. - interrupts: Interrupts used by the MMC controller. -Required properties: -- bus-width: Number of data lines, can be <1>, <4>, or <8> - Card detection: -If no property below is supplied, standard SDHCI card detect is used. +If no property below is supplied, host native card detect is used. Only one of the properties in this section should be supplied: - broken-cd: There is no card detection available; polling must be used. - cd-gpios: Specify GPIOs for card detection, see gpio binding - non-removable: non-removable slot (like eMMC); assume always present. Optional properties: +- bus-width: Number of data lines, can be <1>, <4>, or <8>. The default + will be <1> if the property is absent. - wp-gpios: Specify GPIOs for write protection, see gpio binding -- cd-inverted: when present, polarity on the cd gpio line is inverted -- wp-inverted: when present, polarity on the wp gpio line is inverted +- cd-inverted: when present, polarity on the CD line is inverted. See the note + below for the case, when a GPIO is used for the CD line +- wp-inverted: when present, polarity on the WP line is inverted. See the note + below for the case, when a GPIO is used for the WP line - max-frequency: maximum operating clock frequency - no-1-8-v: when present, denotes that 1.8v card voltage is not supported on this system, even if the controller claims it is. +- cap-sd-highspeed: SD high-speed timing is supported +- cap-mmc-highspeed: MMC high-speed timing is supported +- cap-power-off-card: powering off the card is safe +- cap-sdio-irq: enable SDIO IRQ signalling on this interface + +*NOTE* on CD and WP polarity. To use common for all SD/MMC host controllers line +polarity properties, we have to fix the meaning of the "normal" and "inverted" +line levels. We choose to follow the SDHCI standard, which specifies both those +lines as "active low." Therefore, using the "cd-inverted" property means, that +the CD line is active high, i.e. it is high, when a card is inserted. Similar +logic applies to the "wp-inverted" property. + +CD and WP lines can be implemented on the hardware in one of two ways: as GPIOs, +specified in cd-gpios and wp-gpios properties, or as dedicated pins. Polarity of +dedicated pins can be specified, using *-inverted properties. GPIO polarity can +also be specified using the OF_GPIO_ACTIVE_LOW flag. This creates an ambiguity +in the latter case. We choose to use the XOR logic for GPIO CD and WP lines. +This means, the two properties are "superimposed," for example leaving the +OF_GPIO_ACTIVE_LOW flag clear and specifying the respective *-inverted +property results in a double-inversion and actually means the "normal" line +polarity is in effect. Optional SDIO properties: - keep-power-in-suspend: Preserves card power during a suspend/resume cycle diff --git a/Documentation/devicetree/bindings/mmc/orion-sdio.txt b/Documentation/devicetree/bindings/mmc/orion-sdio.txt new file mode 100644 index 0000000..84f0ebd --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/orion-sdio.txt @@ -0,0 +1,17 @@ +* Marvell orion-sdio controller + +This file documents differences between the core properties in mmc.txt +and the properties used by the orion-sdio driver. + +- compatible: Should be "marvell,orion-sdio" +- clocks: reference to the clock of the SDIO interface + +Example: + + mvsdio@d00d4000 { + compatible = "marvell,orion-sdio"; + reg = <0xd00d4000 0x200>; + interrupts = <54>; + clocks = <&gateclk 17>; + status = "disabled"; + }; diff --git a/Documentation/devicetree/bindings/mmc/synopsis-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/synopsis-dw-mshc.txt index 06cd32d08..726fd21 100644 --- a/Documentation/devicetree/bindings/mmc/synopsis-dw-mshc.txt +++ b/Documentation/devicetree/bindings/mmc/synopsis-dw-mshc.txt @@ -26,8 +26,16 @@ Required Properties: * bus-width: as documented in mmc core bindings. * wp-gpios: specifies the write protect gpio line. The format of the - gpio specifier depends on the gpio controller. If the write-protect - line is not available, this property is optional. + gpio specifier depends on the gpio controller. If a GPIO is not used + for write-protect, this property is optional. + + * disable-wp: If the wp-gpios property isn't present then (by default) + we'd assume that the write protect is hooked up directly to the + controller's special purpose write protect line (accessible via + the WRTPRT register). However, it's possible that we simply don't + want write protect. In that case specify 'disable-wp'. + NOTE: This property is not required for slots known to always + connect to eMMC or SDIO cards. Optional properties: diff --git a/Documentation/devicetree/bindings/mmc/tmio_mmc.txt b/Documentation/devicetree/bindings/mmc/tmio_mmc.txt new file mode 100644 index 0000000..df204e1 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/tmio_mmc.txt @@ -0,0 +1,20 @@ +* Toshiba Mobile IO SD/MMC controller + +The tmio-mmc driver doesn't probe its devices actively, instead its binding to +devices is managed by either MFD drivers or by the sh_mobile_sdhi platform +driver. Those drivers supply the tmio-mmc driver with platform data, that either +describe hardware capabilities, known to them, or are obtained by them from +their own platform data or from their DT information. In the latter case all +compulsory and any optional properties, common to all SD/MMC drivers, as +described in mmc.txt, can be used. Additionally the following tmio_mmc-specific +optional bindings can be used. + +Optional properties: +- toshiba,mmc-wrprotect-disable: write-protect detection is unavailable + +When used with Renesas SDHI hardware, the following compatibility strings +configure various model-specific properties: + +"renesas,sh7372-sdhi": (default) compatible with SH7372 +"renesas,r8a7740-sdhi": compatible with R8A7740: certain MMC/SD commands have to + wait for the interface to become idle. |