Merge tag 'regulator-v3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator

Pull regulator updates from Mark Brown:
 "This release has lots and lots of small cleanups and fixes in the
  regulator subsystem, mainly cleaning up some bad patterns that got
  duplicated in DT code, but otherwise very little of note outside of
  the scope of the relevant drivers:

   - Support for configuration of the initial state for gpio regulators
     with multi-voltage support.
   - Support for calling regulator_set_voltage() on fixed regulators.
   - New drivers for Broadcom BCM590xx, Freescale pfuze200, Samsung
     S2MPA01 & S2MPS11/4, some PWM controlled regulators found on some
     ST boards and TI TPS65218"

* tag 'regulator-v3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (154 commits)
  regulator: aat2870: Use regulator_map_voltage_ascend
  regulator: st-pwm: Convert to get_voltage_sel
  regulator: Add new driver for ST's PWM controlled voltage regulators
  regulator: bcm590xx: Remove **rdev from struct bcm590xx_reg
  regulator: bcm590xx: Make the modalias matches the driver name
  regulator: s5m8767: Convert to use regulator_[enable|disable|is_enabled]_regmap
  regulator: db8500-prcmu: Set 1.8V as a fixed voltage for vsmps2
  regulator: s2mps11: Add missing of_node_put
  regulator: s2mps11: Use of_get_child_by_name
  Documentation: mfd: s2mps11: Document support for S2MPS14
  regulator: s2mps11: Add set_suspend_disable for S2MPS14
  regulator: s2mps11: Add support for S2MPS14 regulators
  regulator: max8660: Fix brace alignment
  regulator: dbx500: use seq_puts() instead of seq_printf()
  regulator: dbx500-prcmu: Silence checkpatch warnings
  regulator: anatop: Remove checking control_reg in [set|get]_voltage_sel
  regulator: max8952: Silence checkpatch warning
  regulator: max8925: Silence checkpatch warning
  regulator: max8660: Silence checkpatch warnings
  regulator: arizona-ldo1: Correct default regulator init_data
  ...

7 files changed, 214 insertions, 9 deletions

diff --git a/Documentation/devicetree/bindings/mfd/s2mpa01.txt b/Documentation/devicetree/bindings/mfd/s2mpa01.txt
new file mode 100644
index 0000000..c13d3d8
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/s2mpa01.txt
@@ -0,0 +1,90 @@
+
+* Samsung S2MPA01 Voltage and Current Regulator
+
+The Samsung S2MPA01 is a multi-function device which includes high
+efficiency buck converters including Dual-Phase buck converter, various LDOs,
+and an RTC. It is interfaced to the host controller using an I2C interface.
+Each sub-block is addressed by the host system using different I2C slave
+addresses.
+
+Required properties:
+- compatible: Should be "samsung,s2mpa01-pmic".
+- reg: Specifies the I2C slave address of the PMIC block. It should be 0x66.
+
+Optional properties:
+- interrupt-parent: Specifies the phandle of the interrupt controller to which
+  the interrupts from s2mpa01 are delivered to.
+- interrupts: An interrupt specifier for the sole interrupt generated by the
+  device.
+
+Optional nodes:
+- regulators: The regulators of s2mpa01 that have to be instantiated should be
+  included in a sub-node named 'regulators'. Regulator nodes and constraints
+  included in this sub-node use the standard regulator bindings which are
+  documented elsewhere.
+
+Properties for BUCK regulator nodes:
+- regulator-ramp-delay: ramp delay in uV/us. May be 6250, 12500
+  (default), 25000, or 50000. May be 0 for disabling the ramp delay on
+  BUCK{1,2,3,4}.
+
+ In the absence of the regulator-ramp-delay property, the default ramp
+ delay will be used.
+
+  NOTE: Some BUCKs share the ramp rate setting i.e. same ramp value will be set
+  for a particular group of BUCKs. So provide same regulator-ramp-delay=<value>.
+
+  The following BUCKs share ramp settings:
+  * 1 and 6
+  * 2 and 4
+  * 8, 9, and 10
+
+The following are the names of the regulators that the s2mpa01 PMIC block
+supports. Note: The 'n' in LDOn and BUCKn represents the LDO or BUCK number
+as per the datasheet of s2mpa01.
+
+	- LDOn
+		  - valid values for n are 1 to 26
+		  - Example: LDO1, LD02, LDO26
+	- BUCKn
+		  - valid values for n are 1 to 10.
+		  - Example: BUCK1, BUCK2, BUCK9
+
+Example:
+
+	s2mpa01_pmic@66 {
+		compatible = "samsung,s2mpa01-pmic";
+		reg = <0x66>;
+
+		regulators {
+			ldo1_reg: LDO1 {
+				regulator-name = "VDD_ALIVE";
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+			};
+
+			ldo2_reg: LDO2 {
+				regulator-name = "VDDQ_MMC2";
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2800000>;
+				regulator-always-on;
+			};
+
+			buck1_reg: BUCK1 {
+				regulator-name = "vdd_mif";
+				regulator-min-microvolt = <950000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			buck2_reg: BUCK2 {
+				regulator-name = "vdd_arm";
+				regulator-min-microvolt = <950000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-ramp-delay = <50000>;
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/mfd/s2mps11.txt b/Documentation/devicetree/bindings/mfd/s2mps11.txt
index 15ee89c3c..f69bec2 100644
--- a/Documentation/devicetree/bindings/mfd/s2mps11.txt
+++ b/Documentation/devicetree/bindings/mfd/s2mps11.txt
@@ -1,5 +1,5 @@
 
-* Samsung S2MPS11 Voltage and Current Regulator
+* Samsung S2MPS11 and S2MPS14 Voltage and Current Regulator
 
 The Samsung S2MPS11 is a multi-function device which includes voltage and
 current regulators, RTC, charger controller and other sub-blocks. It is
@@ -7,7 +7,7 @@ interfaced to the host controller using an I2C interface. Each sub-block is
 addressed by the host system using different I2C slave addresses.
 
 Required properties:
-- compatible: Should be "samsung,s2mps11-pmic".
+- compatible: Should be "samsung,s2mps11-pmic" or "samsung,s2mps14-pmic".
 - reg: Specifies the I2C slave address of the pmic block. It should be 0x66.
 
 Optional properties:
@@ -59,10 +59,14 @@ supports. Note: The 'n' in LDOn and BUCKn represents the LDO or BUCK number
 as per the datasheet of s2mps11.
 
 	- LDOn
-		  - valid values for n are 1 to 38
+		  - valid values for n are:
+			- S2MPS11: 1 to 38
+			- S2MPS14: 1 to 25
 		  - Example: LDO1, LD02, LDO28
 	- BUCKn
-		  - valid values for n are 1 to 10.
+		  - valid values for n are:
+			- S2MPS11: 1 to 10
+			- S2MPS14: 1 to 5
 		  - Example: BUCK1, BUCK2, BUCK9
 
 Example:
diff --git a/Documentation/devicetree/bindings/mfd/tps65910.txt b/Documentation/devicetree/bindings/mfd/tps65910.txt
index b4bd98a..38833e6 100644
--- a/Documentation/devicetree/bindings/mfd/tps65910.txt
+++ b/Documentation/devicetree/bindings/mfd/tps65910.txt
@@ -11,7 +11,7 @@ Required properties:
 - #interrupt-cells: the number of cells to describe an IRQ, this should be 2.
   The first cell is the IRQ number.
   The second cell is the flags, encoded as the trigger masks from
-  Documentation/devicetree/bindings/interrupts.txt
+  Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
 - regulators: This is the list of child nodes that specify the regulator
   initialization data for defined regulators. Not all regulators for the given
   device need to be present. The definition for each of these nodes is defined
diff --git a/Documentation/devicetree/bindings/regulator/gpio-regulator.txt b/Documentation/devicetree/bindings/regulator/gpio-regulator.txt
index 63c6598..e5cac1e 100644
--- a/Documentation/devicetree/bindings/regulator/gpio-regulator.txt
+++ b/Documentation/devicetree/bindings/regulator/gpio-regulator.txt
@@ -8,8 +8,12 @@ Required properties:
 Optional properties:
 - enable-gpio		: GPIO to use to enable/disable the regulator.
 - gpios			: GPIO group used to control voltage.
+- gpios-states		: gpios pin's initial states array. 0: LOW, 1: HIGH.
+			  defualt is LOW if nothing is specified.
 - startup-delay-us	: Startup time in microseconds.
 - enable-active-high	: Polarity of GPIO is active high (default is low).
+- regulator-type	: Specifies what is being regulated, must be either
+			  "voltage" or "current", defaults to current.
 
 Any property defined as part of the core regulator binding defined in
 regulator.txt can also be used.
diff --git a/Documentation/devicetree/bindings/regulator/pfuze100.txt b/Documentation/devicetree/bindings/regulator/pfuze100.txt
index fc989b2..34ef5d1 100644
--- a/Documentation/devicetree/bindings/regulator/pfuze100.txt
+++ b/Documentation/devicetree/bindings/regulator/pfuze100.txt
@@ -1,7 +1,7 @@
 PFUZE100 family of regulators
 
 Required properties:
-- compatible: "fsl,pfuze100"
+- compatible: "fsl,pfuze100" or "fsl,pfuze200"
 - reg: I2C slave address
 
 Required child node:
@@ -10,11 +10,14 @@ Required child node:
   Documentation/devicetree/bindings/regulator/regulator.txt.
 
   The valid names for regulators are:
+  --PFUZE100
   sw1ab,sw1c,sw2,sw3a,sw3b,sw4,swbst,vsnvs,vrefddr,vgen1~vgen6
+  --PFUZE200
+  sw1ab,sw2,sw3a,sw3b,swbst,vsnvs,vrefddr,vgen1~vgen6
 
 Each regulator is defined using the standard binding for regulators.
 
-Example:
+Example 1: PFUZE100
 
 	pmic: pfuze100@08 {
 		compatible = "fsl,pfuze100";
@@ -113,3 +116,92 @@ Example:
 			};
 		};
 	};
+
+
+Example 2: PFUZE200
+
+	pmic: pfuze200@08 {
+		compatible = "fsl,pfuze200";
+		reg = <0x08>;
+
+		regulators {
+			sw1a_reg: sw1ab {
+				regulator-min-microvolt = <300000>;
+				regulator-max-microvolt = <1875000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <6250>;
+			};
+
+			sw2_reg: sw2 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			sw3a_reg: sw3a {
+				regulator-min-microvolt = <400000>;
+				regulator-max-microvolt = <1975000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			sw3b_reg: sw3b {
+				regulator-min-microvolt = <400000>;
+				regulator-max-microvolt = <1975000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			swbst_reg: swbst {
+				regulator-min-microvolt = <5000000>;
+				regulator-max-microvolt = <5150000>;
+			};
+
+			snvs_reg: vsnvs {
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			vref_reg: vrefddr {
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			vgen1_reg: vgen1 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1550000>;
+			};
+
+			vgen2_reg: vgen2 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1550000>;
+			};
+
+			vgen3_reg: vgen3 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			vgen4_reg: vgen4 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen5_reg: vgen5 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen6_reg: vgen6 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/regulator/s5m8767-regulator.txt b/Documentation/devicetree/bindings/regulator/s5m8767-regulator.txt
index fc6b38f..d290988 100644
--- a/Documentation/devicetree/bindings/regulator/s5m8767-regulator.txt
+++ b/Documentation/devicetree/bindings/regulator/s5m8767-regulator.txt
@@ -69,13 +69,16 @@ sub-node should be of the format as listed below.
 		};
 	};
 The above regulator entries are defined in regulator bindings documentation
-except op_mode description.
+except these properties:
 	- op_mode: describes the different operating modes of the LDO's with
 		power mode change in SOC. The different possible values are,
 		0 - always off mode
 		1 - on in normal mode
 		2 - low power mode
 		3 - suspend mode
+	- s5m8767,pmic-ext-control-gpios: (optional) GPIO specifier for one
+		GPIO controlling this regulator (enable/disable); This is
+		valid only for buck9.
 
 The following are the names of the regulators that the s5m8767 pmic block
 supports. Note: The 'n' in LDOn and BUCKn represents the LDO or BUCK number
@@ -148,5 +151,13 @@ Example:
 				regulator-always-on;
 				regulator-boot-on;
 			};
+
+			vemmc_reg: BUCK9 {
+				regulator-name = "VMEM_VDD_2.8V";
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2800000>;
+				op_mode = <3>; /* Standby Mode */
+				s5m8767,pmic-ext-control-gpios = <&gpk0 2 0>;
+			};
 		};
 	};
diff --git a/Documentation/devicetree/bindings/regulator/ti-abb-regulator.txt b/Documentation/devicetree/bindings/regulator/ti-abb-regulator.txt
index 2e57a33..c58db75 100644
--- a/Documentation/devicetree/bindings/regulator/ti-abb-regulator.txt
+++ b/Documentation/devicetree/bindings/regulator/ti-abb-regulator.txt
@@ -4,10 +4,14 @@ Required Properties:
 - compatible: Should be one of:
   - "ti,abb-v1" for older SoCs like OMAP3
   - "ti,abb-v2" for newer SoCs like OMAP4, OMAP5
+  - "ti,abb-v3" for a generic definition where setup and control registers are
+     provided (example: DRA7)
 - reg: Address and length of the register set for the device. It contains
   the information of registers in the same order as described by reg-names
 - reg-names: Should contain the reg names
-  - "base-address"	- contains base address of ABB module
+  - "base-address"	- contains base address of ABB module (ti,abb-v1,ti,abb-v2)
+  - "control-address"	- contains control register address of ABB module (ti,abb-v3)
+  - "setup-address"	- contains setup register address of ABB module (ti,abb-v3)
   - "int-address"	- contains address of interrupt register for ABB module
   (also see Optional properties)
 - #address-cell: should be 0