Merge tag 'usb-4.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb

Pull USB updates from Greg KH:
 "Here's the big USB and PHY patchset for 4.3-rc1.

  As usual, the majority of the changes are in the USB gadget portion of
  the tree, lots of little changes all over the place for bugs and new
  hardware.  Other than that, the normal mix of new hardware support and
  bugfixes.

  All have been in linux-next with no reported issues"

* tag 'usb-4.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (261 commits)
  USB: qcserial: add HP lt4111 LTE/EV-DO/HSPA+ Gobi 4G Module
  USB: ftdi_sio: Added custom PID for CustomWare products
  USB: usb_wwan: silence read errors on disconnect
  USB: option: silence interrupt errors
  USB: symbolserial: Correct transferred data size
  USB: symbolserial: Use usb_get_serial_port_data
  usb: misc: usbtest: format max packet size for iso transfer
  usb: host: ehci-sys: delete useless bus_to_hcd conversion
  Revert "usb: interface authorization: Declare authorized attribute"
  Revert "usb: interface authorization: Introduces the default interface authorization"
  Revert "usb: interface authorization: Control interface probing and claiming"
  Revert "usb: interface authorization: Introduces the USB interface authorization"
  Revert "usb: interface authorization: SysFS part of USB interface authorization"
  Revert "usb: interface authorization: Documentation part"
  Revert "usb: interface authorization: Use a flag for the default device authorization"
  usb: core: hub: Removed some warnings generated by checkpatch.pl
  USB: host: ohci-at91: merge loops in ohci_hcd_at91_drv_probe
  USB: host: ohci-at91: merge ohci_at91_of_init in ohci_hcd_at91_drv_probe
  USB: host: ohci-at91: depend on OF
  USB: host: ohci-at91: move at91_usbh_data definition in c file
  ...

12 files changed, 221 insertions, 11 deletions

diff --git a/Documentation/ABI/testing/configfs-usb-gadget-loopback b/Documentation/ABI/testing/configfs-usb-gadget-loopback
index 9aae5bf..06beefbc 100644
--- a/Documentation/ABI/testing/configfs-usb-gadget-loopback
+++ b/Documentation/ABI/testing/configfs-usb-gadget-loopback
@@ -5,4 +5,4 @@ Description:
 		The attributes:
 
 		qlen		- depth of loopback queue
-		bulk_buflen	- buffer length
+		buflen		- buffer length
diff --git a/Documentation/ABI/testing/configfs-usb-gadget-sourcesink b/Documentation/ABI/testing/configfs-usb-gadget-sourcesink
index 29477c3..bc7ff73 100644
--- a/Documentation/ABI/testing/configfs-usb-gadget-sourcesink
+++ b/Documentation/ABI/testing/configfs-usb-gadget-sourcesink
@@ -9,4 +9,4 @@ Description:
 		isoc_maxpacket	- 0 - 1023 (fs), 0 - 1024 (hs/ss)
 		isoc_mult	- 0..2 (hs/ss only)
 		isoc_maxburst	- 0..15 (ss only)
-		qlen		- buffer length
+		buflen		- buffer length
diff --git a/Documentation/ABI/testing/sysfs-bus-usb b/Documentation/ABI/testing/sysfs-bus-usb
index e5cc763..864637f 100644
--- a/Documentation/ABI/testing/sysfs-bus-usb
+++ b/Documentation/ABI/testing/sysfs-bus-usb
@@ -114,6 +114,20 @@ Description:
 		enabled for the device. Developer can write y/Y/1 or n/N/0 to
 		the file to enable/disable the feature.
 
+What:		/sys/bus/usb/devices/.../power/usb3_hardware_lpm
+Date:		June 2015
+Contact:	Kevin Strasser <kevin.strasser@linux.intel.com>
+Description:
+		If CONFIG_PM is set and a USB 3.0 lpm-capable device is plugged
+		in to a xHCI host which supports link PM, it will check if U1
+		and U2 exit latencies have been set in the BOS descriptor; if
+		the check is is passed and the host supports USB3 hardware LPM,
+		USB3 hardware LPM will be enabled for the device and the USB
+		device directory will contain a file named
+		power/usb3_hardware_lpm. The file holds a string value (enable
+		or disable) indicating whether or not USB3 hardware LPM is
+		enabled for the device.
+
 What:		/sys/bus/usb/devices/.../removable
 Date:		February 2012
 Contact:	Matthew Garrett <mjg@redhat.com>
diff --git a/Documentation/devicetree/bindings/phy/phy-lpc18xx-usb-otg.txt b/Documentation/devicetree/bindings/phy/phy-lpc18xx-usb-otg.txt
new file mode 100644
index 0000000..bd61b46
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/phy-lpc18xx-usb-otg.txt
@@ -0,0 +1,26 @@
+NXP LPC18xx/43xx internal USB OTG PHY binding
+---------------------------------------------
+
+This file contains documentation for the internal USB OTG PHY found
+in NXP LPC18xx and LPC43xx SoCs.
+
+Required properties:
+- compatible	: must be "nxp,lpc1850-usb-otg-phy"
+- clocks	: must be exactly one entry
+See: Documentation/devicetree/bindings/clock/clock-bindings.txt
+- #phy-cells	: must be 0 for this phy
+See: Documentation/devicetree/bindings/phy/phy-bindings.txt
+
+The phy node must be a child of the creg syscon node.
+
+Example:
+creg: syscon@40043000 {
+	compatible = "nxp,lpc1850-creg", "syscon", "simple-mfd";
+	reg = <0x40043000 0x1000>;
+
+	usb0_otg_phy: phy@004 {
+		compatible = "nxp,lpc1850-usb-otg-phy";
+		clocks = <&ccu1 CLK_USB0>;
+		#phy-cells = <0>;
+	};
+};
diff --git a/Documentation/devicetree/bindings/phy/sun4i-usb-phy.txt b/Documentation/devicetree/bindings/phy/sun4i-usb-phy.txt
index 16528b9..0cebf74 100644
--- a/Documentation/devicetree/bindings/phy/sun4i-usb-phy.txt
+++ b/Documentation/devicetree/bindings/phy/sun4i-usb-phy.txt
@@ -7,6 +7,8 @@ Required properties:
   * allwinner,sun5i-a13-usb-phy
   * allwinner,sun6i-a31-usb-phy
   * allwinner,sun7i-a20-usb-phy
+  * allwinner,sun8i-a23-usb-phy
+  * allwinner,sun8i-a33-usb-phy
 - reg : a list of offset + length pairs
 - reg-names :
   * "phy_ctrl"
@@ -17,12 +19,21 @@ Required properties:
 - clock-names :
   * "usb_phy" for sun4i, sun5i or sun7i
   * "usb0_phy", "usb1_phy" and "usb2_phy" for sun6i
+  * "usb0_phy", "usb1_phy" for sun8i
 - resets : a list of phandle + reset specifier pairs
 - reset-names :
   * "usb0_reset"
   * "usb1_reset"
   * "usb2_reset" for sun4i, sun6i or sun7i
 
+Optional properties:
+- usb0_id_det-gpios : gpio phandle for reading the otg id pin value
+- usb0_vbus_det-gpios : gpio phandle for detecting the presence of usb0 vbus
+- usb0_vbus_power-supply: power-supply phandle for usb0 vbus presence detect
+- usb0_vbus-supply : regulator phandle for controller usb0 vbus
+- usb1_vbus-supply : regulator phandle for controller usb1 vbus
+- usb2_vbus-supply : regulator phandle for controller usb2 vbus
+
 Example:
 	usbphy: phy@0x01c13400 {
 		#phy-cells = <1>;
@@ -32,6 +43,13 @@ Example:
 		reg-names = "phy_ctrl", "pmu1", "pmu2";
 		clocks = <&usb_clk 8>;
 		clock-names = "usb_phy";
-		resets = <&usb_clk 1>, <&usb_clk 2>;
-		reset-names = "usb1_reset", "usb2_reset";
+		resets = <&usb_clk 0>, <&usb_clk 1>, <&usb_clk 2>;
+		reset-names = "usb0_reset", "usb1_reset", "usb2_reset";
+		pinctrl-names = "default";
+		pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>;
+		usb0_id_det-gpios = <&pio 7 19 GPIO_ACTIVE_HIGH>; /* PH19 */
+		usb0_vbus_det-gpios = <&pio 7 22 GPIO_ACTIVE_HIGH>; /* PH22 */
+		usb0_vbus-supply = <&reg_usb0_vbus>;
+		usb1_vbus-supply = <&reg_usb1_vbus>;
+		usb2_vbus-supply = <&reg_usb2_vbus>;
 	};
diff --git a/Documentation/devicetree/bindings/usb/allwinner,sun4i-a10-musb.txt b/Documentation/devicetree/bindings/usb/allwinner,sun4i-a10-musb.txt
new file mode 100644
index 0000000..862cd7c
--- /dev/null
+++ b/Documentation/devicetree/bindings/usb/allwinner,sun4i-a10-musb.txt
@@ -0,0 +1,29 @@
+Allwinner sun4i A10 musb DRC/OTG controller
+-------------------------------------------
+
+Required properties:
+ - compatible      : "allwinner,sun4i-a10-musb", "allwinner,sun6i-a31-musb"
+                     or "allwinner,sun8i-a33-musb"
+ - reg             : mmio address range of the musb controller
+ - clocks          : clock specifier for the musb controller ahb gate clock
+ - reset           : reset specifier for the ahb reset (A31 and newer only)
+ - interrupts      : interrupt to which the musb controller is connected
+ - interrupt-names : must be "mc"
+ - phys            : phy specifier for the otg phy
+ - phy-names       : must be "usb"
+ - dr_mode         : Dual-Role mode must be "host" or "otg"
+ - extcon          : extcon specifier for the otg phy
+
+Example:
+
+	usb_otg: usb@01c13000 {
+		compatible = "allwinner,sun4i-a10-musb";
+		reg = <0x01c13000 0x0400>;
+		clocks = <&ahb_gates 0>;
+		interrupts = <38>;
+		interrupt-names = "mc";
+		phys = <&usbphy 0>;
+		phy-names = "usb";
+		extcon = <&usbphy 0>;
+		status = "disabled";
+	};
diff --git a/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt b/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt
index 553e2fa..d71ef07 100644
--- a/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt
+++ b/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt
@@ -30,6 +30,21 @@ Optional properties:
   argument that indicate usb controller index
 - disable-over-current: (FSL only) disable over current detect
 - external-vbus-divider: (FSL only) enables off-chip resistor divider for Vbus
+- itc-setting: interrupt threshold control register control, the setting
+  should be aligned with ITC bits at register USBCMD.
+- ahb-burst-config: it is vendor dependent, the required value should be
+  aligned with AHBBRST at SBUSCFG, the range is from 0x0 to 0x7. This
+  property is used to change AHB burst configuration, check the chipidea
+  spec for meaning of each value. If this property is not existed, it
+  will use the reset value.
+- tx-burst-size-dword: it is vendor dependent, the tx burst size in dword
+  (4 bytes), This register represents the maximum length of a the burst
+  in 32-bit words while moving data from system memory to the USB
+  bus, changing this value takes effect only the SBUSCFG.AHBBRST is 0.
+- rx-burst-size-dword: it is vendor dependent, the rx burst size in dword
+  (4 bytes), This register represents the maximum length of a the burst
+  in 32-bit words while moving data from the USB bus to system memory,
+  changing this value takes effect only the SBUSCFG.AHBBRST is 0.
 
 Example:
 
@@ -41,4 +56,9 @@ Example:
 		phys = <&usb_phy0>;
 		phy-names = "usb-phy";
 		vbus-supply = <&reg_usb0_vbus>;
+		gadget-itc-setting = <0x4>; /* 4 micro-frames */
+		 /* Incremental burst of unspecified length */
+		ahb-burst-config = <0x0>;
+		tx-burst-size-dword = <0x10>; /* 64 bytes */
+		rx-burst-size-dword = <0x10>;
 	};
diff --git a/Documentation/devicetree/bindings/usb/generic.txt b/Documentation/devicetree/bindings/usb/generic.txt
index 477d5bb..bba8257 100644
--- a/Documentation/devicetree/bindings/usb/generic.txt
+++ b/Documentation/devicetree/bindings/usb/generic.txt
@@ -11,6 +11,19 @@ Optional properties:
 			"peripheral" and "otg". In case this attribute isn't
 			passed via DT, USB DRD controllers should default to
 			OTG.
+ - otg-rev: tells usb driver the release number of the OTG and EH supplement
+			with which the device and its descriptors are compliant,
+			in binary-coded decimal (i.e. 2.0 is 0200H). This
+			property is used if any real OTG features(HNP/SRP/ADP)
+			is enabled, if ADP is required, otg-rev should be
+			0x0200 or above.
+ - hnp-disable: tells OTG controllers we want to disable OTG HNP, normally HNP
+			is the basic function of real OTG except you want it
+			to be a srp-capable only B device.
+ - srp-disable: tells OTG controllers we want to disable OTG SRP, SRP is
+			optional for OTG device.
+ - adp-disable: tells OTG controllers we want to disable OTG ADP, ADP is
+			optional for OTG device.
 
 This is an attribute to a USB controller such as:
 
@@ -21,4 +34,6 @@ dwc3@4a030000 {
 	usb-phy = <&usb2_phy>, <&usb3,phy>;
 	maximum-speed = "super-speed";
 	dr_mode = "otg";
+	otg-rev = <0x0200>;
+	adp-disable;
 };
diff --git a/Documentation/devicetree/bindings/usb/msm-hsusb.txt b/Documentation/devicetree/bindings/usb/msm-hsusb.txt
index bd8d9e7..8654a3e 100644
--- a/Documentation/devicetree/bindings/usb/msm-hsusb.txt
+++ b/Documentation/devicetree/bindings/usb/msm-hsusb.txt
@@ -52,6 +52,10 @@ Required properties:
 Optional properties:
 - dr_mode:      One of "host", "peripheral" or "otg". Defaults to "otg"
 
+- switch-gpio:  A phandle + gpio-specifier pair. Some boards are using Dual
+                SPDT USB Switch, witch is cotrolled by GPIO to de/multiplex
+                D+/D- USB lines between connectors.
+
 - qcom,phy-init-sequence: PHY configuration sequence values. This is related to Device
                 Mode Eye Diagram test. Start address at which these values will be
                 written is ULPI_EXT_VENDOR_SPECIFIC. Value of -1 is reserved as
diff --git a/Documentation/devicetree/bindings/usb/qcom,usb-8x16-phy.txt b/Documentation/devicetree/bindings/usb/qcom,usb-8x16-phy.txt
new file mode 100644
index 0000000..2cb2168
--- /dev/null
+++ b/Documentation/devicetree/bindings/usb/qcom,usb-8x16-phy.txt
@@ -0,0 +1,76 @@
+Qualcomm's APQ8016/MSM8916 USB transceiver controller
+
+- compatible:
+    Usage: required
+    Value type: <string>
+    Definition: Should contain "qcom,usb-8x16-phy".
+
+- reg:
+    Usage: required
+    Value type: <prop-encoded-array>
+    Definition: USB PHY base address and length of the register map
+
+- clocks:
+    Usage: required
+    Value type: <prop-encoded-array>
+    Definition: See clock-bindings.txt section "consumers". List of
+                two clock specifiers for interface and core controller
+                clocks.
+
+- clock-names:
+    Usage: required
+    Value type: <string>
+    Definition: Must contain "iface" and "core" strings.
+
+- vddcx-supply:
+    Usage: required
+    Value type: <phandle>
+    Definition: phandle to the regulator VDCCX supply node.
+
+- v1p8-supply:
+    Usage: required
+    Value type: <phandle>
+    Definition: phandle to the regulator 1.8V supply node.
+
+- v3p3-supply:
+    Usage: required
+    Value type: <phandle>
+    Definition: phandle to the regulator 3.3V supply node.
+
+- resets:
+    Usage: required
+    Value type: <prop-encoded-array>
+    Definition: See reset.txt section "consumers". PHY reset specifier.
+
+- reset-names:
+    Usage: required
+    Value type: <string>
+    Definition: Must contain "phy" string.
+
+- switch-gpio:
+    Usage: optional
+    Value type: <prop-encoded-array>
+    Definition: Some boards are using Dual SPDT USB Switch, witch is
+                controlled by GPIO to de/multiplex D+/D- USB lines
+                between connectors.
+
+Example:
+	usb_phy: phy@78d9000 {
+		compatible = "qcom,usb-8x16-phy";
+		reg = <0x78d9000 0x400>;
+
+		vddcx-supply = <&pm8916_s1_corner>;
+		v1p8-supply = <&pm8916_l7>;
+		v3p3-supply = <&pm8916_l13>;
+
+		clocks = <&gcc GCC_USB_HS_AHB_CLK>,
+			     <&gcc GCC_USB_HS_SYSTEM_CLK>;
+		clock-names = "iface", "core";
+
+		resets = <&gcc GCC_USB2A_PHY_BCR>;
+		reset-names = "phy";
+
+		// D+/D- lines: 1 - Routed to HUB, 0 - Device connector
+		switch-gpio = <&pm8916_gpios 4 GPIO_ACTIVE_HIGH>;
+	};
+
diff --git a/Documentation/usb/gadget-testing.txt b/Documentation/usb/gadget-testing.txt
index 5926780..b24d3ef 100644
--- a/Documentation/usb/gadget-testing.txt
+++ b/Documentation/usb/gadget-testing.txt
@@ -237,9 +237,7 @@ Testing the LOOPBACK function
 -----------------------------
 
 device: run the gadget
-host: test-usb
-
-http://www.linux-usb.org/usbtest/testusb.c
+host: test-usb (tools/usb/testusb.c)
 
 8. MASS STORAGE function
 ========================
@@ -586,9 +584,8 @@ Testing the SOURCESINK function
 -------------------------------
 
 device: run the gadget
-host: test-usb
+host: test-usb (tools/usb/testusb.c)
 
-http://www.linux-usb.org/usbtest/testusb.c
 
 16. UAC1 function
 =================
diff --git a/Documentation/usb/power-management.txt b/Documentation/usb/power-management.txt
index b5f8391..4a15c90 100644
--- a/Documentation/usb/power-management.txt
+++ b/Documentation/usb/power-management.txt
@@ -521,10 +521,10 @@ enabling hardware LPM, the host can automatically put the device into
 lower power state(L1 for usb2.0 devices, or U1/U2 for usb3.0 devices),
 which state device can enter and resume very quickly.
 
-The user interface for controlling USB2 hardware LPM is located in the
+The user interface for controlling hardware LPM is located in the
 power/ subdirectory of each USB device's sysfs directory, that is, in
 /sys/bus/usb/devices/.../power/ where "..." is the device's ID. The
-relevant attribute files is usb2_hardware_lpm.
+relevant attribute files are usb2_hardware_lpm and usb3_hardware_lpm.
 
 	power/usb2_hardware_lpm
 
@@ -537,6 +537,17 @@ relevant attribute files is usb2_hardware_lpm.
 		can write y/Y/1 or n/N/0 to the file to	enable/disable
 		USB2 hardware LPM manually. This is for	test purpose mainly.
 
+	power/usb3_hardware_lpm
+
+		When a USB 3.0 lpm-capable device is plugged in to a
+		xHCI host which supports link PM, it will check if U1
+		and U2 exit latencies have been set in the BOS
+		descriptor; if the check is is passed and the host
+		supports USB3 hardware LPM, USB3 hardware LPM will be
+		enabled for the device and this file will be created.
+		The file holds a string value (enable or disable)
+		indicating whether or not USB3 hardware LPM is
+		enabled for the device.
 
 	USB Port Power Control
 	----------------------