Merge tag 'kvm-arm-for-4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into kvm-next

KVM/ARM changes for Linux v4.5

- Complete rewrite of the arm64 world switch in C, hopefully
  paving the way for more sharing with the 32bit code, better
  maintainability and easier integration of new features.
  Also smaller and slightly faster in some cases...
- Support for 16bit VM identifiers
- Various cleanups

5 files changed, 16 insertions, 19 deletions

diff --git a/Documentation/arm/keystone/Overview.txt b/Documentation/arm/keystone/Overview.txt
index f17bc4c..400c0c2 100644
--- a/Documentation/arm/keystone/Overview.txt
+++ b/Documentation/arm/keystone/Overview.txt
@@ -49,24 +49,6 @@ specified through DTS. Following are the DTS used:-
 The device tree documentation for the keystone machines are located at
         Documentation/devicetree/bindings/arm/keystone/keystone.txt
 
-Known issues & workaround
--------------------------
-
-Some of the device drivers used on keystone are re-used from that from
-DaVinci and other TI SoCs. These device drivers may use clock APIs directly.
-Some of the keystone specific drivers such as netcp uses run time power
-management API instead to enable clock. As this API has limitations on
-keystone, following workaround is needed to boot Linux.
-
-   Add 'clk_ignore_unused' to the bootargs env variable in u-boot. Otherwise
-   clock frameworks will try to disable clocks that are unused and disable
-   the hardware. This is because netcp related power domain and clock
-   domains are enabled in u-boot as run time power management API currently
-   doesn't enable clocks for netcp due to a limitation. This workaround is
-   expected to be removed in the future when proper API support becomes
-   available. Until then, this work around is needed.
-
-
 Document Author
 ---------------
 Murali Karicheri <m-karicheri2@ti.com>
diff --git a/Documentation/block/null_blk.txt b/Documentation/block/null_blk.txt
index 2f6c6ff..d8880ca 100644
--- a/Documentation/block/null_blk.txt
+++ b/Documentation/block/null_blk.txt
@@ -70,3 +70,6 @@ use_per_node_hctx=[0/1]: Default: 0
      parameter.
   1: The multi-queue block layer is instantiated with a hardware dispatch
      queue for each CPU node in the system.
+
+use_lightnvm=[0/1]: Default: 0
+  Register device with LightNVM. Requires blk-mq to be used.
diff --git a/Documentation/devicetree/bindings/gpio/gpio-mpc8xxx.txt b/Documentation/devicetree/bindings/gpio/gpio-mpc8xxx.txt
index f2455c5..120bc49 100644
--- a/Documentation/devicetree/bindings/gpio/gpio-mpc8xxx.txt
+++ b/Documentation/devicetree/bindings/gpio/gpio-mpc8xxx.txt
@@ -11,6 +11,10 @@ Required properties:
       0 = active high
       1 = active low
 
+Optional properties:
+- little-endian : GPIO registers are used as little endian. If not
+                  present registers are used as big endian by default.
+
 Example:
 
 gpio0: gpio@1100 {
diff --git a/Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt b/Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt
index f5a8ca2..aeea50c 100644
--- a/Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt
+++ b/Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt
@@ -8,6 +8,11 @@ Required properties:
 - phy-mode: See ethernet.txt file in the same directory
 - clocks: a pointer to the reference clock for this device.
 
+Optional properties:
+- tx-csum-limit: maximum mtu supported by port that allow TX checksum.
+  Value is presented in bytes. If not used, by default 1600B is set for
+  "marvell,armada-370-neta" and 9800B for others.
+
 Example:
 
 ethernet@d0070000 {
@@ -15,6 +20,7 @@ ethernet@d0070000 {
 	reg = <0xd0070000 0x2500>;
 	interrupts = <8>;
 	clocks = <&gate_clk 4>;
+	tx-csum-limit = <9800>
 	status = "okay";
 	phy = <&phy0>;
 	phy-mode = "rgmii-id";
diff --git a/Documentation/devicetree/bindings/thermal/rockchip-thermal.txt b/Documentation/devicetree/bindings/thermal/rockchip-thermal.txt
index b38200d..0dfa60d 100644
--- a/Documentation/devicetree/bindings/thermal/rockchip-thermal.txt
+++ b/Documentation/devicetree/bindings/thermal/rockchip-thermal.txt
@@ -1,7 +1,9 @@
 * Temperature Sensor ADC (TSADC) on rockchip SoCs
 
 Required properties:
-- compatible : "rockchip,rk3288-tsadc"
+- compatible : should be "rockchip,<name>-tsadc"
+   "rockchip,rk3288-tsadc": found on RK3288 SoCs
+   "rockchip,rk3368-tsadc": found on RK3368 SoCs
 - reg : physical base address of the controller and length of memory mapped
 	region.
 - interrupts : The interrupt number to the cpu. The interrupt specifier format