Merge tag 'qcom-dt-for-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux into next/dt

Qualcomm Device Tree Changes for v4.8

* Reverse BAM dma node reverts
* Add BAM remote control options for affected platforms
* Enable peripherals on APQ8074 dragonboard
* Enable PMA8084 pwrky
* Fix PMIC reg entries by removing unnecessary size element
* Add SCM binding and support for all currently supported boards
* Add Qualcomm WCNSS binding documentation
* Rename db600c to SD_600eval and add peripheral nodes
* Remove gpio key entry from Nexus7
* Add APQ8060 based dragonboard and associated peripherals
* Add ARMv7 PMU for IPQ4019
* Update smem state cells to match documentation

* tag 'qcom-dt-for-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux: (26 commits)
  dts: ipq4019: support ARMv7 PMU
  ARM: dts: add Qualcomm APQ8060-based Dragonboard
  ARM: dts: move the fixed MMC regulator to SURF board
  ARM: dts: fix the MSM8660 RTC base address
  ARM: dts: add I2C block in GSBI12
  ARM: dts: add L2CC and RPM with regulators for MSM8660
  ARM: dts: add SDCC5 to Qualcomm MSM8660
  ARM: dts: add GPIO and MPP to MSM8660 PMIC
  device-tree: nexus7: Remove power gpio key entry and use pmic8xxx-pwrkey
  arm: dts: qcom: Update smem state cells usage
  ARM: dts: qcom: msm8974-honami: Set DMA as remotely controlled
  ARM: dts: sd_600eval: Fix eMMC lockup issue
  ARM: dts: apq8064: rename db600c to SD_600eval
  ARM: dts: apq8064: move sdcc3 pinctrls out of baord file
  ARM: dts: apq8064: move sdcc1 pinctrl nodes to soc file
  dt: binding: Add Qualcomm WCNSS control binding
  dts: qcom: apq8064: Add SCM firmware node
  dts: qcom: msm8974: Add SCM firmware node
  dts: qcom: apq8084: Add SCM firmware node
  dt/bindings: firmware: Add Qualcomm SCM binding
  ...

Signed-off-by: Olof Johansson <olof@lixom.net>

16 files changed, 1152 insertions, 77 deletions

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 6dfefa3..1739959 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -578,7 +578,8 @@ dtb-$(CONFIG_ARCH_PRIMA2) += \
 dtb-$(CONFIG_ARCH_OXNAS) += \
 	wd-mbwe.dtb
 dtb-$(CONFIG_ARCH_QCOM) += \
-	qcom-apq8064-arrow-db600c.dtb \
+	qcom-apq8060-dragonboard.dtb \
+	qcom-apq8064-arrow-sd-600eval.dtb \
 	qcom-apq8064-cm-qs600.dtb \
 	qcom-apq8064-ifc6410.dtb \
 	qcom-apq8064-sony-xperia-yuga.dtb \
diff --git a/arch/arm/boot/dts/qcom-apq8060-dragonboard.dts b/arch/arm/boot/dts/qcom-apq8060-dragonboard.dts
new file mode 100644
index 0000000..0abc93e
--- /dev/null
+++ b/arch/arm/boot/dts/qcom-apq8060-dragonboard.dts
@@ -0,0 +1,626 @@
+/*
+ * Copyright 2016 Linaro Ltd
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a copy
+ * of this software and associated documentation files (the "Software"), to deal
+ * in the Software without restriction, including without limitation the rights
+ * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
+ * copies of the Software, and to permit persons to whom the Software is
+ * furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in
+ * all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL
+ * THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+ * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+ * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
+ * THE SOFTWARE.
+ */
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+#include "qcom-msm8660.dtsi"
+
+/ {
+	model = "Qualcomm APQ8060 Dragonboard";
+	compatible = "qcom,apq8060-dragonboard", "qcom,msm8660";
+
+	aliases {
+		serial0 = &gsbi12_serial;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	regulators {
+		compatible = "simple-bus";
+
+		/* Main power of the board: 3.7V */
+		vph: regulator-fixed {
+			compatible = "regulator-fixed";
+			regulator-min-microvolt = <3700000>;
+			regulator-max-microvolt = <3700000>;
+			regulator-name = "VPH";
+			regulator-type = "voltage";
+			regulator-always-on;
+			regulator-boot-on;
+		};
+
+		/* This is a levelshifter for SDCC5 */
+		dragon_vio_txb: txb0104rgyr {
+			compatible = "regulator-fixed";
+			regulator-name = "Dragon SDCC levelshifter";
+			vin-supply = <&pm8058_l14>;
+			regulator-always-on;
+		};
+	};
+
+	soc {
+		pinctrl@800000 {
+			/* eMMMC pins, all 8 data lines connected */
+			dragon_sdcc1_pins: sdcc1 {
+				mux {
+					pins = "gpio159", "gpio160", "gpio161",
+					     "gpio162", "gpio163", "gpio164",
+					     "gpio165", "gpio166", "gpio167",
+					     "gpio168";
+					     function = "sdc1";
+				};
+				clk {
+					pins = "gpio167"; /* SDC5 CLK */
+					drive-strength = <16>;
+					bias-disable;
+				};
+				cmd {
+					pins = "gpio168"; /* SDC5 CMD */
+					drive-strength = <10>;
+					bias-pull-up;
+				};
+				data {
+					/* SDC5 D0 to D7 */
+					pins = "gpio159", "gpio160", "gpio161", "gpio162",
+					     "gpio163", "gpio164", "gpio165", "gpio166";
+					drive-strength = <10>;
+					bias-pull-up;
+				};
+			};
+
+			/*
+			 * The SDCC3 pins are hardcoded (non-muxable) but need some pin
+			 * configuration.
+			 */
+			dragon_sdcc3_pins: sdcc3 {
+				clk {
+					pins = "sdc3_clk";
+					drive-strength = <8>;
+					bias-disable;
+				};
+				cmd {
+					pins = "sdc3_cmd";
+					drive-strength = <8>;
+					bias-pull-up;
+				};
+				data {
+					pins = "sdc3_data";
+					drive-strength = <8>;
+					bias-pull-up;
+				};
+			};
+
+			/* Second SD card slot pins */
+			dragon_sdcc5_pins: sdcc5 {
+				mux {
+					pins = "gpio95", "gpio96", "gpio97",
+					    "gpio98", "gpio99", "gpio100";
+					function = "sdc5";
+				};
+				clk {
+					pins = "gpio97"; /* SDC5 CLK */
+					drive-strength = <16>;
+					bias-disable;
+				};
+				cmd {
+					pins = "gpio95"; /* SDC5 CMD */
+					drive-strength = <10>;
+					bias-pull-up;
+				};
+				data {
+					/* SDC5 D0 to D3 */
+					pins = "gpio96", "gpio98", "gpio99", "gpio100";
+					drive-strength = <10>;
+					bias-pull-up;
+				};
+			};
+
+			dragon_gsbi12_i2c_pins: gsbi12_i2c {
+				mux {
+					pins = "gpio115", "gpio116";
+					function = "gsbi12";
+				};
+				pinconf {
+					pins = "gpio115", "gpio116";
+					drive-strength = <16>;
+					/* These have external pull-up 4.7kOhm to 1.8V */
+					bias-disable;
+				};
+			};
+
+			/* Primary serial port uart 0 pins */
+			dragon_gsbi12_serial_pins: gsbi12_serial {
+				mux {
+					pins = "gpio117", "gpio118";
+					function = "gsbi12";
+				};
+				tx {
+					pins = "gpio117";
+					drive-strength = <8>;
+					bias-disable;
+				};
+				rx {
+					pins = "gpio118";
+					drive-strength = <2>;
+					bias-pull-up;
+				};
+			};
+		};
+
+		qcom,ssbi@500000 {
+			pmic@0 {
+				keypad@148 {
+					linux,keymap = <
+					MATRIX_KEY(0, 0, KEY_MENU)
+					MATRIX_KEY(0, 2, KEY_1)
+					MATRIX_KEY(0, 3, KEY_4)
+					MATRIX_KEY(0, 4, KEY_7)
+					MATRIX_KEY(1, 0, KEY_UP)
+					MATRIX_KEY(1, 1, KEY_LEFT)
+					MATRIX_KEY(1, 2, KEY_DOWN)
+					MATRIX_KEY(1, 3, KEY_5)
+					MATRIX_KEY(1, 3, KEY_8)
+					MATRIX_KEY(2, 0, KEY_HOME)
+					MATRIX_KEY(2, 1, KEY_REPLY)
+					MATRIX_KEY(2, 2, KEY_2)
+					MATRIX_KEY(2, 3, KEY_6)
+					MATRIX_KEY(3, 0, KEY_VOLUMEUP)
+					MATRIX_KEY(3, 1, KEY_RIGHT)
+					MATRIX_KEY(3, 2, KEY_3)
+					MATRIX_KEY(3, 3, KEY_9)
+					MATRIX_KEY(3, 4, KEY_SWITCHVIDEOMODE)
+					MATRIX_KEY(4, 0, KEY_VOLUMEDOWN)
+					MATRIX_KEY(4, 1, KEY_BACK)
+					MATRIX_KEY(4, 2, KEY_CAMERA)
+					MATRIX_KEY(4, 3, KEY_KBDILLUMTOGGLE)
+					>;
+					keypad,num-rows = <6>;
+					keypad,num-columns = <5>;
+				};
+
+				gpio@150 {
+					dragon_bmp085_gpios: bmp085-gpios {
+						pinconf {
+							pins = "gpio16";
+							function = "normal";
+							input-enable;
+							bias-disable;
+							power-source = <PM8058_GPIO_S3>;
+						};
+					};
+					dragon_sdcc3_gpios: sdcc3-gpios {
+						pinconf {
+							pins = "gpio22";
+							function = "normal";
+							input-enable;
+							bias-disable;
+							power-source = <PM8058_GPIO_S3>;
+						};
+					};
+					dragon_sdcc5_gpios: sdcc5-gpios {
+						pinconf {
+							pins = "gpio26";
+							function = "normal";
+							input-enable;
+							bias-pull-up;
+							qcom,pull-up-strength = <PMIC_GPIO_PULL_UP_30>;
+							power-source = <PM8058_GPIO_S3>;
+						};
+					};
+					dragon_ak8975_gpios: ak8975-gpios {
+						pinconf {
+							pins = "gpio33";
+							function = "normal";
+							input-enable;
+							bias-disable;
+							power-source = <PM8058_GPIO_S3>;
+						};
+					};
+				};
+			};
+		};
+
+		gsbi@19c00000 {
+			status = "ok";
+			qcom,mode = <GSBI_PROT_I2C_UART>;
+
+			serial@19c40000 {
+				status = "ok";
+				pinctrl-names = "default";
+				pinctrl-0 = <&dragon_gsbi12_serial_pins>;
+			};
+
+			i2c@19c80000 {
+				status = "ok";
+				pinctrl-names = "default";
+				pinctrl-0 = <&dragon_gsbi12_i2c_pins>;
+
+				ak8975@0c {
+					compatible = "asahi-kasei,ak8975";
+					reg = <0x0c>;
+					/* GPIO33 has interrupt 224 on the PM8058 */
+					interrupt-parent = <&pm8058_gpio>;
+					interrupts = <224 IRQ_TYPE_EDGE_RISING>;
+					pinctrl-names = "default";
+					pinctrl-0 = <&dragon_ak8975_gpios>;
+					vid-supply = <&pm8058_lvs0>; // 1.8V
+					vdd-supply = <&pm8058_l14>; // 2.85V
+				};
+				bmp085@77 {
+					compatible = "bosch,bmp085";
+					reg = <0x77>;
+					/* GPIO16 has interrupt 207 on the PM8058 */
+					interrupt-parent = <&pm8058_gpio>;
+					interrupts = <207 IRQ_TYPE_EDGE_RISING>;
+					reset-gpios = <&tlmm 86 GPIO_ACTIVE_LOW>;
+					pinctrl-names = "default";
+					pinctrl-0 = <&dragon_bmp085_gpios>;
+					vddd-supply = <&pm8058_lvs0>; // 1.8V
+					vdda-supply = <&pm8058_l14>; // 2.85V
+				};
+			};
+		};
+
+		rpm@104000 {
+			/*
+			 * Set up of the PMIC RPM regulators for this board
+			 * PM8901 supplies "preliminary regulators" whatever
+			 * that means
+			 */
+			pm8901-regulators {
+				vdd_l0-supply = <&pm8901_s4>;
+				vdd_l1-supply = <&vph>;
+				vdd_l2-supply = <&vph>;
+				vdd_l3-supply = <&vph>;
+				vdd_l4-supply = <&vph>;
+				vdd_l5-supply = <&vph>;
+				vdd_l6-supply = <&vph>;
+				/* vdd_s0-supply, vdd_s1-supply: SAW regulators */
+				vdd_s2-supply = <&vph>;
+				vdd_s3-supply = <&vph>;
+				vdd_s4-supply = <&vph>;
+				lvs0_in-supply = <&pm8058_s3>;
+				lvs1_in-supply = <&pm8901_s4>;
+				lvs2_in-supply = <&pm8058_l0>;
+				lvs3_in-supply = <&pm8058_s2>;
+				mvs_in-supply = <&pm8058_s3>;
+
+				l0 {
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+					bias-pull-down;
+				};
+				l1 {
+					regulator-min-microvolt = <3300000>;
+					regulator-max-microvolt = <3300000>;
+					bias-pull-down;
+				};
+				l2 {
+					regulator-min-microvolt = <2850000>;
+					regulator-max-microvolt = <3300000>;
+					bias-pull-down;
+				};
+				l3 {
+					regulator-min-microvolt = <3300000>;
+					regulator-max-microvolt = <3300000>;
+					bias-pull-down;
+				};
+				l4 {
+					regulator-min-microvolt = <2600000>;
+					regulator-max-microvolt = <2600000>;
+					bias-pull-down;
+				};
+				l5 {
+					regulator-min-microvolt = <2850000>;
+					regulator-max-microvolt = <2850000>;
+					bias-pull-down;
+				};
+				l6 {
+					regulator-min-microvolt = <2200000>;
+					regulator-max-microvolt = <2200000>;
+					bias-pull-down;
+				};
+
+				/* s0 and s1 are SAW regulators controlled over SPM */
+				s2 {
+					regulator-min-microvolt = <1300000>;
+					regulator-max-microvolt = <1300000>;
+					qcom,switch-mode-frequency = <1600000>;
+					bias-pull-down;
+				};
+				s3 {
+					regulator-min-microvolt = <1100000>;
+					regulator-max-microvolt = <1100000>;
+					qcom,switch-mode-frequency = <1600000>;
+					bias-pull-down;
+				};
+				s4 {
+					regulator-min-microvolt = <1225000>;
+					regulator-max-microvolt = <1225000>;
+					qcom,switch-mode-frequency = <1600000>;
+					bias-pull-down;
+				};
+
+				/* LVS0 thru 3 and mvs0 are just switches */
+				lvs0 {
+					regulator-always-on;
+				};
+				lvs1 { };
+				lvs2 { };
+				lvs3 { };
+				mvs0 {};
+
+			};
+
+			pm8058-regulators {
+				vdd_l0_l1_lvs-supply = <&pm8058_s3>;
+				vdd_l2_l11_l12-supply = <&vph>;
+				vdd_l3_l4_l5-supply = <&vph>;
+				vdd_l6_l7-supply = <&vph>;
+				vdd_l8-supply = <&vph>;
+				vdd_l9-supply = <&vph>;
+				vdd_l10-supply = <&vph>;
+				vdd_l13_l16-supply = <&pm8058_s4>;
+				vdd_l14_l15-supply = <&vph>;
+				vdd_l17_l18-supply = <&vph>;
+				vdd_l19_l20-supply = <&vph>;
+				vdd_l21-supply = <&pm8058_s3>;
+				vdd_l22-supply = <&pm8058_s3>;
+				vdd_l23_l24_l25-supply = <&pm8058_s3>;
+				vdd_s0-supply = <&vph>;
+				vdd_s1-supply = <&vph>;
+				vdd_s2-supply = <&vph>;
+				vdd_s3-supply = <&vph>;
+				vdd_s4-supply = <&vph>;
+				vdd_ncp-supply = <&vph>;
+
+				l0 {
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+					bias-pull-down;
+				};
+				l1 {
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+					bias-pull-down;
+				};
+				l2 {
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <2600000>;
+					bias-pull-down;
+				};
+				l3 {
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					bias-pull-down;
+				};
+				l4 {
+					regulator-min-microvolt = <2850000>;
+					regulator-max-microvolt = <2850000>;
+					bias-pull-down;
+				};
+				l5 {
+					regulator-min-microvolt = <2850000>;
+					regulator-max-microvolt = <2850000>;
+					bias-pull-down;
+				};
+				l6 {
+					regulator-min-microvolt = <3000000>;
+					regulator-max-microvolt = <3600000>;
+					bias-pull-down;
+				};
+				l7 {
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					bias-pull-down;
+				};
+				l8 {
+					regulator-min-microvolt = <2900000>;
+					regulator-max-microvolt = <3050000>;
+					bias-pull-down;
+				};
+				l9 {
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					bias-pull-down;
+				};
+				l10 {
+					regulator-min-microvolt = <2600000>;
+					regulator-max-microvolt = <2600000>;
+					bias-pull-down;
+				};
+				l11 {
+					regulator-min-microvolt = <1500000>;
+					regulator-max-microvolt = <1500000>;
+					bias-pull-down;
+				};
+				l12 {
+					regulator-min-microvolt = <2900000>;
+					regulator-max-microvolt = <2900000>;
+					bias-pull-down;
+				};
+				l13 {
+					regulator-min-microvolt = <2050000>;
+					regulator-max-microvolt = <2050000>;
+					bias-pull-down;
+				};
+				l14 {
+					regulator-min-microvolt = <2850000>;
+					regulator-max-microvolt = <2850000>;
+				};
+				l15 {
+					regulator-min-microvolt = <2850000>;
+					regulator-max-microvolt = <2850000>;
+					bias-pull-down;
+				};
+				l16 {
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					bias-pull-down;
+					regulator-always-on;
+				};
+				l17 {
+					// 1.5V according to schematic
+					regulator-min-microvolt = <2600000>;
+					regulator-max-microvolt = <2600000>;
+					bias-pull-down;
+				};
+				l18 {
+					regulator-min-microvolt = <2200000>;
+					regulator-max-microvolt = <2200000>;
+					bias-pull-down;
+				};
+				l19 {
+					regulator-min-microvolt = <2500000>;
+					regulator-max-microvolt = <2500000>;
+					bias-pull-down;
+				};
+				l20 {
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					bias-pull-down;
+				};
+				l21 {
+					// 1.1 V according to schematic
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+					bias-pull-down;
+					regulator-always-on;
+				};
+				l22 {
+					// 1.2 V according to schematic
+					regulator-min-microvolt = <1150000>;
+					regulator-max-microvolt = <1150000>;
+					bias-pull-down;
+				};
+				l23 {
+					// Unused
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+					bias-pull-down;
+				};
+				l24 {
+					// Unused
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+					bias-pull-down;
+				};
+				l25 {
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+					bias-pull-down;
+				};
+
+				s0 {
+					// regulator-min-microvolt = <500000>;
+					// regulator-max-microvolt = <1325000>;
+					regulator-min-microvolt = <1100000>;
+					regulator-max-microvolt = <1100000>;
+					qcom,switch-mode-frequency = <1600000>;
+					bias-pull-down;
+				};
+				s1 {
+					// regulator-min-microvolt = <500000>;
+					// regulator-max-microvolt = <1250000>;
+					regulator-min-microvolt = <1100000>;
+					regulator-max-microvolt = <1100000>;
+					qcom,switch-mode-frequency = <1600000>;
+					bias-pull-down;
+				};
+				s2 {
+					// 1.3 V according to schematic
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1400000>;
+					qcom,switch-mode-frequency = <1600000>;
+					bias-pull-down;
+				};
+				s3 {
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					qcom,switch-mode-frequency = <1600000>;
+					regulator-always-on;
+					bias-pull-down;
+				};
+				s4 {
+					regulator-min-microvolt = <2200000>;
+					regulator-max-microvolt = <2200000>;
+					qcom,switch-mode-frequency = <1600000>;
+					regulator-always-on;
+					bias-pull-down;
+				};
+
+				/* LVS0 and LVS1 are just switches */
+				lvs0 {
+					bias-pull-down;
+				};
+				lvs1 {
+					bias-pull-down;
+				};
+
+				ncp {
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					qcom,switch-mode-frequency = <1600000>;
+				};
+			};
+		};
+		amba {
+			/* Internal 3.69 GiB eMMC */
+			sdcc@12400000 {
+				status = "okay";
+				pinctrl-names = "default";
+				pinctrl-0 = <&dragon_sdcc1_pins>;
+				vmmc-supply = <&pm8901_l5>;
+				vqmmc-supply = <&pm8901_lvs0>;
+			};
+
+			/* External micro SD card, directly connected, pulled up to 2.85 V */
+			sdcc@12180000 {
+				status = "okay";
+				/* Enable SSBI GPIO 22 as input, use for card detect */
+				pinctrl-names = "default";
+				pinctrl-0 = <&dragon_sdcc3_pins>, <&dragon_sdcc3_gpios>;
+				cd-gpios = <&pm8058_gpio 22 GPIO_ACTIVE_LOW>;
+				wp-gpios = <&tlmm 110 GPIO_ACTIVE_HIGH>;
+				vmmc-supply = <&pm8058_l14>;
+			};
+
+			/*
+			 * Second external micro SD card, using two TXB104RGYR levelshifters
+			 * to lift from 1.8 V to 2.85 V
+			 */
+			sdcc@12200000 {
+				status = "okay";
+				/* Enable SSBI GPIO 26 as input, use for card detect */
+				pinctrl-names = "default";
+				pinctrl-0 = <&dragon_sdcc5_pins>, <&dragon_sdcc5_gpios>;
+				cd-gpios = <&pm8058_gpio 26 GPIO_ACTIVE_LOW>;
+				wp-gpios = <&tlmm 106 GPIO_ACTIVE_HIGH>;
+				vmmc-supply = <&pm8058_l14>;
+				vqmmc-supply = <&dragon_vio_txb>;
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/qcom-apq8064-arrow-db600c-pins.dtsi b/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval-pins.dtsi
index a3efb97..a3efb97 100644
--- a/arch/arm/boot/dts/qcom-apq8064-arrow-db600c-pins.dtsi
+++ b/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval-pins.dtsi
diff --git a/arch/arm/boot/dts/qcom-apq8064-arrow-db600c.dts b/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts
index e01b27e..39ae2bc 100644
--- a/arch/arm/boot/dts/qcom-apq8064-arrow-db600c.dts
+++ b/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts
@@ -1,10 +1,11 @@
 #include "qcom-apq8064-v2.0.dtsi"
-#include "qcom-apq8064-arrow-db600c-pins.dtsi"
+#include "qcom-apq8064-arrow-sd-600eval-pins.dtsi"
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/mfd/qcom-rpm.h>
 
 / {
-	model = "Arrow Electronics, APQ8064 DB600c";
-	compatible = "arrow,db600c", "qcom,apq8064";
+	model = "Arrow Electronics, APQ8064 SD_600eval";
+	compatible = "arrow,sd_600eval", "qcom,apq8064";
 
 	aliases {
 		serial0 = &gsbi7_serial;
@@ -82,7 +83,8 @@
 				s4 {
 					regulator-min-microvolt	= <1800000>;
 					regulator-max-microvolt	= <1800000>;
-					qcom,switch-mode-frequency = <3200000>;
+					qcom,switch-mode-frequency = <1600000>;
+					qcom,force-mode = <QCOM_RPM_FORCE_MODE_AUTO>;
 					bias-pull-down;
 					regulator-always-on;
 				};
diff --git a/arch/arm/boot/dts/qcom-apq8064-asus-nexus7-flo.dts b/arch/arm/boot/dts/qcom-apq8064-asus-nexus7-flo.dts
index 32fedfa..7b05f07 100644
--- a/arch/arm/boot/dts/qcom-apq8064-asus-nexus7-flo.dts
+++ b/arch/arm/boot/dts/qcom-apq8064-asus-nexus7-flo.dts
@@ -29,12 +29,6 @@
 
 	gpio-keys {
 		compatible = "gpio-keys";
-		power {
-			label = "Power";
-			gpios = <&tlmm_pinmux 26 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_POWER>;
-			gpio-key,wakeup;
-		};
 		volume_up {
 			label = "Volume Up";
 			gpios = <&pm8921_gpio 4 GPIO_ACTIVE_HIGH>;
diff --git a/arch/arm/boot/dts/qcom-apq8064-pins.dtsi b/arch/arm/boot/dts/qcom-apq8064-pins.dtsi
index 4102a98..6b801e7 100644
--- a/arch/arm/boot/dts/qcom-apq8064-pins.dtsi
+++ b/arch/arm/boot/dts/qcom-apq8064-pins.dtsi
@@ -7,6 +7,46 @@
 		};
 	};
 
+	sdcc1_pins: sdcc1-pin-active {
+		clk {
+			pins = "sdc1_clk";
+			drive-strengh = <16>;
+			bias-disable;
+		};
+
+		cmd {
+			pins = "sdc1_cmd";
+			drive-strengh = <10>;
+			bias-pull-up;
+		};
+
+		data {
+			pins = "sdc1_data";
+			drive-strengh = <10>;
+			bias-pull-up;
+		};
+	};
+
+	sdcc3_pins: sdcc3-pin-active {
+		clk {
+			pins = "sdc3_clk";
+			drive-strengh = <8>;
+			bias-disable;
+		};
+
+		cmd {
+			pins = "sdc3_cmd";
+			drive-strengh = <8>;
+			bias-pull-up;
+		};
+
+		data {
+			pins = "sdc3_data";
+			drive-strengh = <8>;
+			bias-pull-up;
+		};
+	};
+
 	ps_hold: ps_hold {
 		mux {
 			pins = "gpio78";
diff --git a/arch/arm/boot/dts/qcom-apq8064-sony-xperia-yuga.dts b/arch/arm/boot/dts/qcom-apq8064-sony-xperia-yuga.dts
index 06b3c76..ebd675c 100644
--- a/arch/arm/boot/dts/qcom-apq8064-sony-xperia-yuga.dts
+++ b/arch/arm/boot/dts/qcom-apq8064-sony-xperia-yuga.dts
@@ -70,45 +70,6 @@
 				};
 			};
 
-			sdcc1_pin_a: sdcc1-pin-active {
-				clk {
-					pins = "sdc1_clk";
-					drive-strengh = <16>;
-					bias-disable;
-				};
-
-				cmd {
-					pins = "sdc1_cmd";
-					drive-strengh = <10>;
-					bias-pull-up;
-				};
-
-				data {
-					pins = "sdc1_data";
-					drive-strengh = <10>;
-					bias-pull-up;
-				};
-			};
-
-			sdcc3_pin_a: sdcc3-pin-active {
-				clk {
-					pins = "sdc3_clk";
-					drive-strengh = <8>;
-					bias-disable;
-				};
-
-				cmd {
-					pins = "sdc3_cmd";
-					drive-strengh = <8>;
-					bias-pull-up;
-				};
-
-				data {
-					pins = "sdc3_data";
-					drive-strengh = <8>;
-					bias-pull-up;
-				};
-			};
 
 			sdcc3_cd_pin_a: sdcc3-cd-pin-active {
 				pins = "gpio26";
@@ -417,9 +378,6 @@
 
 				vmmc-supply = <&pm8921_l5>;
 				vqmmc-supply = <&pm8921_s4>;
-
-				pinctrl-names = "default";
-				pinctrl-0 = <&sdcc1_pin_a>;
 			};
 
 			sdcc3: sdcc@12180000 {
@@ -429,7 +387,7 @@
 				cd-gpios = <&tlmm_pinmux 26 GPIO_ACTIVE_LOW>;
 
 				pinctrl-names = "default";
-				pinctrl-0 = <&sdcc3_pin_a>, <&sdcc3_cd_pin_a>;
+				pinctrl-0 = <&sdcc3_pins>, <&sdcc3_cd_pin_a>;
 			};
 		};
 	};
diff --git a/arch/arm/boot/dts/qcom-apq8064.dtsi b/arch/arm/boot/dts/qcom-apq8064.dtsi
index df96ccd..906bb81 100644
--- a/arch/arm/boot/dts/qcom-apq8064.dtsi
+++ b/arch/arm/boot/dts/qcom-apq8064.dtsi
@@ -177,7 +177,7 @@
 
 		apps_smsm: apps@0 {
 			reg = <0>;
-			#qcom,state-cells = <1>;
+			#qcom,smem-state-cells = <1>;
 		};
 
 		modem_smsm: modem@1 {
@@ -213,6 +213,12 @@
 		};
 	};
 
+	firmware {
+		scm {
+			compatible = "qcom,scm-apq8064";
+		};
+	};
+
 	soc: soc {
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -853,6 +859,8 @@
 			sdcc1: sdcc@12400000 {
 				status		= "disabled";
 				compatible	= "arm,pl18x", "arm,primecell";
+				pinctrl-names	= "default";
+				pinctrl-0	= <&sdcc1_pins>;
 				arm,primecell-periphid = <0x00051180>;
 				reg		= <0x12400000 0x2000>;
 				interrupts	= <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>;
diff --git a/arch/arm/boot/dts/qcom-apq8074-dragonboard.dts b/arch/arm/boot/dts/qcom-apq8074-dragonboard.dts
index c0e2053..ad51df2 100644
--- a/arch/arm/boot/dts/qcom-apq8074-dragonboard.dts
+++ b/arch/arm/boot/dts/qcom-apq8074-dragonboard.dts
@@ -25,11 +25,23 @@
 			bus-width = <8>;
 			non-removable;
 			status = "ok";
+
+			vmmc-supply = <&pm8941_l20>;
+			vqmmc-supply = <&pm8941_s3>;
+
+			pinctrl-names = "default";
+			pinctrl-0 = <&sdhc1_pin_a>;
 		};
 
 		sdhci@f98a4900 {
 			cd-gpios = <&msmgpio 62 0x1>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&sdhc2_pin_a>, <&sdhc2_cd_pin_a>;
 			bus-width = <4>;
+			status = "ok";
+
+			vmmc-supply = <&pm8941_l21>;
+			vqmmc-supply = <&pm8941_l13>;
 		};
 
 
@@ -59,6 +71,42 @@
 					function = "blsp_spi8";
 				};
 			};
+
+			sdhc1_pin_a: sdhc1-pin-active {
+				clk {
+					pins = "sdc1_clk";
+					drive-strength = <16>;
+					bias-disable;
+				};
+
+				cmd-data {
+					pins = "sdc1_cmd", "sdc1_data";
+					drive-strength = <10>;
+					bias-pull-up;
+				};
+			};
+
+			sdhc2_cd_pin_a: sdhc2-cd-pin-active {
+				pins = "gpio62";
+				function = "gpio";
+
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			sdhc2_pin_a: sdhc2-pin-active {
+				clk {
+					pins = "sdc2_clk";
+					drive-strength = <10>;
+					bias-disable;
+				};
+
+				cmd-data {
+					pins = "sdc2_cmd", "sdc2_data";
+					drive-strength = <6>;
+					bias-pull-up;
+				};
+			};
 		};
 
 		i2c@f9967000 {
@@ -75,4 +123,203 @@
 			};
 		};
 	};
+
+	smd {
+		rpm {
+			rpm_requests {
+				pm8841-regulators {
+					s1 {
+						regulator-min-microvolt = <675000>;
+						regulator-max-microvolt = <1050000>;
+					};
+
+					s2 {
+						regulator-min-microvolt = <500000>;
+						regulator-max-microvolt = <1050000>;
+					};
+
+					s3 {
+						regulator-min-microvolt = <500000>;
+						regulator-max-microvolt = <1050000>;
+					};
+
+					s4 {
+						regulator-min-microvolt = <500000>;
+						regulator-max-microvolt = <1050000>;
+					};
+				};
+
+				pm8941-regulators {
+					vdd_l1_l3-supply = <&pm8941_s1>;
+					vdd_l2_lvs1_2_3-supply = <&pm8941_s3>;
+					vdd_l4_l11-supply = <&pm8941_s1>;
+					vdd_l5_l7-supply = <&pm8941_s2>;
+					vdd_l6_l12_l14_l15-supply = <&pm8941_s2>;
+					vin_5vs-supply = <&pm8941_5v>;
+
+					s1 {
+						regulator-min-microvolt = <1300000>;
+						regulator-max-microvolt = <1300000>;
+						regulator-always-on;
+						regulator-boot-on;
+					};
+
+					s2 {
+						regulator-min-microvolt = <2150000>;
+						regulator-max-microvolt = <2150000>;
+						regulator-boot-on;
+					};
+
+					s3 {
+						regulator-min-microvolt = <1800000>;
+						regulator-max-microvolt = <1800000>;
+						regulator-always-on;
+						regulator-boot-on;
+					};
+
+					l1 {
+						regulator-min-microvolt = <1225000>;
+						regulator-max-microvolt = <1225000>;
+
+						regulator-always-on;
+						regulator-boot-on;
+					};
+
+					l2 {
+						regulator-min-microvolt = <1200000>;
+						regulator-max-microvolt = <1200000>;
+					};
+
+					l3 {
+						regulator-min-microvolt = <1225000>;
+						regulator-max-microvolt = <1225000>;
+					};
+
+					l4 {
+						regulator-min-microvolt = <1225000>;
+						regulator-max-microvolt = <1225000>;
+					};
+
+					l5 {
+						regulator-min-microvolt = <1800000>;
+						regulator-max-microvolt = <1800000>;
+					};
+
+					l6 {
+						regulator-min-microvolt = <1800000>;
+						regulator-max-microvolt = <1800000>;
+
+						regulator-boot-on;
+					};
+
+					l7 {
+						regulator-min-microvolt = <1800000>;
+						regulator-max-microvolt = <1800000>;
+
+						regulator-boot-on;
+					};
+
+					l8 {
+						regulator-min-microvolt = <1800000>;
+						regulator-max-microvolt = <1800000>;
+					};
+
+					l9 {
+						regulator-min-microvolt = <1800000>;
+						regulator-max-microvolt = <2950000>;
+					};
+
+					l10 {
+						regulator-min-microvolt = <1800000>;
+						regulator-max-microvolt = <1800000>;
+						regulator-always-on;
+					};
+
+					l11 {
+						regulator-min-microvolt = <1300000>;
+						regulator-max-microvolt = <1300000>;
+					};
+
+					l12 {
+						regulator-min-microvolt = <1800000>;
+						regulator-max-microvolt = <1800000>;
+
+						regulator-always-on;
+						regulator-boot-on;
+					};
+
+					l13 {
+						regulator-min-microvolt = <1800000>;
+						regulator-max-microvolt = <2950000>;
+
+						regulator-boot-on;
+					};
+
+					l14 {
+						regulator-min-microvolt = <1800000>;
+						regulator-max-microvolt = <1800000>;
+					};
+
+					l15 {
+						regulator-min-microvolt = <2050000>;
+						regulator-max-microvolt = <2050000>;
+					};
+
+					l16 {
+						regulator-min-microvolt = <2700000>;
+						regulator-max-microvolt = <2700000>;
+					};
+
+					l17 {
+						regulator-min-microvolt = <2700000>;
+						regulator-max-microvolt = <2700000>;
+					};
+
+					l18 {
+						regulator-min-microvolt = <2850000>;
+						regulator-max-microvolt = <2850000>;
+					};
+
+					l19 {
+						regulator-min-microvolt = <3300000>;
+						regulator-max-microvolt = <3300000>;
+						regulator-always-on;
+					};
+
+					l20 {
+						regulator-min-microvolt = <2950000>;
+						regulator-max-microvolt = <2950000>;
+
+						regulator-allow-set-load;
+						regulator-boot-on;
+						regulator-system-load = <200000>;
+					};
+
+					l21 {
+						regulator-min-microvolt = <2950000>;
+						regulator-max-microvolt = <2950000>;
+
+						regulator-boot-on;
+					};
+
+					l22 {
+						regulator-min-microvolt = <3000000>;
+						regulator-max-microvolt = <3000000>;
+					};
+
+					l23 {
+						regulator-min-microvolt = <3000000>;
+						regulator-max-microvolt = <3000000>;
+					};
+
+					l24 {
+						regulator-min-microvolt = <3075000>;
+						regulator-max-microvolt = <3075000>;
+
+						regulator-boot-on;
+					};
+				};
+			};
+		};
+	};
 };
diff --git a/arch/arm/boot/dts/qcom-apq8084.dtsi b/arch/arm/boot/dts/qcom-apq8084.dtsi
index a33a09f..7c2df06 100644
--- a/arch/arm/boot/dts/qcom-apq8084.dtsi
+++ b/arch/arm/boot/dts/qcom-apq8084.dtsi
@@ -86,6 +86,14 @@
 		};
 	};
 
+	firmware {
+		scm {
+			compatible = "qcom,scm";
+			clocks = <&gcc GCC_CE1_CLK> , <&gcc GCC_CE1_AXI_CLK>, <&gcc GCC_CE1_AHB_CLK>;
+			clock-names = "core", "bus", "iface";
+		};
+	};
+
 	cpu-pmu {
 		compatible = "qcom,krait-pmu";
 		interrupts = <1 7 0xf04>;
diff --git a/arch/arm/boot/dts/qcom-ipq4019.dtsi b/arch/arm/boot/dts/qcom-ipq4019.dtsi
index 5c08d19..a520ef5 100644
--- a/arch/arm/boot/dts/qcom-ipq4019.dtsi
+++ b/arch/arm/boot/dts/qcom-ipq4019.dtsi
@@ -84,6 +84,12 @@
 		};
 	};
 
+	pmu {
+		compatible = "arm,cortex-a7-pmu";
+		interrupts = <GIC_PPI 7 (GIC_CPU_MASK_SIMPLE(4) |
+					 IRQ_TYPE_LEVEL_HIGH)>;
+	};
+
 	clocks {
 		sleep_clk: sleep_clk {
 			compatible = "fixed-clock";
diff --git a/arch/arm/boot/dts/qcom-msm8660-surf.dts b/arch/arm/boot/dts/qcom-msm8660-surf.dts
index b17f379..23de764 100644
--- a/arch/arm/boot/dts/qcom-msm8660-surf.dts
+++ b/arch/arm/boot/dts/qcom-msm8660-surf.dts
@@ -23,15 +23,26 @@
 			};
 		};
 
+		/* Temporary fixed regulator */
+		vsdcc_fixed: vsdcc-regulator {
+			compatible = "regulator-fixed";
+			regulator-name = "SDCC Power";
+			regulator-min-microvolt = <2700000>;
+			regulator-max-microvolt = <2700000>;
+			regulator-always-on;
+		};
+
 		amba {
 			/* eMMC */
 			sdcc1: sdcc@12400000 {
 				status = "okay";
+				vmmc-supply = <&vsdcc_fixed>;
 			};
 
 			/* External micro SD card */
 			sdcc3: sdcc@12180000 {
 				status = "okay";
+				vmmc-supply = <&vsdcc_fixed>;
 			};
 		};
 	};
diff --git a/arch/arm/boot/dts/qcom-msm8660.dtsi b/arch/arm/boot/dts/qcom-msm8660.dtsi
index cd21403..acbe71f 100644
--- a/arch/arm/boot/dts/qcom-msm8660.dtsi
+++ b/arch/arm/boot/dts/qcom-msm8660.dtsi
@@ -122,11 +122,22 @@
 				compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
 				reg = <0x19c40000 0x1000>,
 				      <0x19c00000 0x1000>;
-				interrupts = <0 195 0x0>;
+				interrupts = <0 195 IRQ_TYPE_NONE>;
 				clocks = <&gcc GSBI12_UART_CLK>, <&gcc GSBI12_H_CLK>;
 				clock-names = "core", "iface";
 				status = "disabled";
 			};
+
+			gsbi12_i2c: i2c@19c80000 {
+				compatible = "qcom,i2c-qup-v1.1.1";
+				reg = <0x19c80000 0x1000>;
+				interrupts = <0 196 IRQ_TYPE_NONE>;
+				clocks = <&gcc GSBI12_QUP_CLK>, <&gcc GSBI12_H_CLK>;
+				clock-names = "core", "iface";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
 		};
 
 		qcom,ssbi@500000 {
@@ -143,6 +154,44 @@
 				#address-cells = <1>;
 				#size-cells = <0>;
 
+				pm8058_gpio: gpio@150 {
+					compatible = "qcom,pm8058-gpio",
+						     "qcom,ssbi-gpio";
+					reg = <0x150>;
+					interrupt-parent = <&pmicintc>;
+					interrupts = <192 1>, <193 1>, <194 1>,
+						     <195 1>, <196 1>, <197 1>,
+						     <198 1>, <199 1>, <200 1>,
+						     <201 1>, <202 1>, <203 1>,
+						     <204 1>, <205 1>, <206 1>,
+						     <207 1>, <208 1>, <209 1>,
+						     <210 1>, <211 1>, <212 1>,
+						     <213 1>, <214 1>, <215 1>,
+						     <216 1>, <217 1>, <218 1>,
+						     <219 1>, <220 1>, <221 1>,
+						     <222 1>, <223 1>, <224 1>,
+						     <225 1>, <226 1>, <227 1>,
+						     <228 1>, <229 1>, <230 1>,
+						     <231 1>, <232 1>, <233 1>,
+						     <234 1>, <235 1>;
+					gpio-controller;
+					#gpio-cells = <2>;
+
+				};
+
+				pm8058_mpps: mpps@50 {
+					compatible = "qcom,pm8058-mpp",
+						     "qcom,ssbi-mpp";
+					reg = <0x50>;
+					gpio-controller;
+					#gpio-cells = <2>;
+					interrupt-parent = <&pmicintc>;
+					interrupts =
+					<128 1>, <129 1>, <130 1>, <131 1>,
+					<132 1>, <133 1>, <134 1>, <135 1>,
+					<136 1>, <137 1>, <138 1>, <139 1>;
+				};
+
 				pwrkey@1c {
 					compatible = "qcom,pm8058-pwrkey";
 					reg = <0x1c>;
@@ -162,11 +211,11 @@
 					row-hold = <91500>;
 				};
 
-				rtc@11d {
+				rtc@1e8 {
 					compatible = "qcom,pm8058-rtc";
+					reg = <0x1e8>;
 					interrupt-parent = <&pmicintc>;
 					interrupts = <39 1>;
-					reg = <0x11d>;
 					allow-set-time;
 				};
 
@@ -177,13 +226,93 @@
 			};
 		};
 
-		/* Temporary fixed regulator */
-		vsdcc_fixed: vsdcc-regulator {
-			compatible = "regulator-fixed";
-			regulator-name = "SDCC Power";
-			regulator-min-microvolt = <2700000>;
-			regulator-max-microvolt = <2700000>;
-			regulator-always-on;
+		l2cc: clock-controller@2082000 {
+			compatible	= "syscon";
+			reg		= <0x02082000 0x1000>;
+		};
+
+		rpm: rpm@104000 {
+			compatible	= "qcom,rpm-msm8660";
+			reg		= <0x00104000 0x1000>;
+			qcom,ipc	= <&l2cc 0x8 2>;
+
+			interrupts	= <GIC_SPI 19 IRQ_TYPE_EDGE_RISING>,
+					  <GIC_SPI 21 IRQ_TYPE_EDGE_RISING>,
+					  <GIC_SPI 22 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names	= "ack", "err", "wakeup";
+			clocks = <&gcc RPM_MSG_RAM_H_CLK>;
+			clock-names = "ram";
+
+			rpmcc: clock-controller {
+				compatible	= "qcom,rpmcc-apq8660", "qcom,rpmcc";
+				#clock-cells = <1>;
+			};
+
+			pm8901-regulators {
+				compatible = "qcom,rpm-pm8901-regulators";
+
+				pm8901_l0: l0 {};
+				pm8901_l1: l1 {};
+				pm8901_l2: l2 {};
+				pm8901_l3: l3 {};
+				pm8901_l4: l4 {};
+				pm8901_l5: l5 {};
+				pm8901_l6: l6 {};
+
+				/* S0 and S1 Handled as SAW regulators by SPM */
+				pm8901_s2: s2 {};
+				pm8901_s3: s3 {};
+				pm8901_s4: s4 {};
+
+				pm8901_lvs0: lvs0 {};
+				pm8901_lvs1: lvs1 {};
+				pm8901_lvs2: lvs2 {};
+				pm8901_lvs3: lvs3 {};
+
+				pm8901_mvs: mvs {};
+			};
+
+			pm8058-regulators {
+				compatible = "qcom,rpm-pm8058-regulators";
+
+				pm8058_l0: l0 {};
+				pm8058_l1: l1 {};
+				pm8058_l2: l2 {};
+				pm8058_l3: l3 {};
+				pm8058_l4: l4 {};
+				pm8058_l5: l5 {};
+				pm8058_l6: l6 {};
+				pm8058_l7: l7 {};
+				pm8058_l8: l8 {};
+				pm8058_l9: l9 {};
+				pm8058_l10: l10 {};
+				pm8058_l11: l11 {};
+				pm8058_l12: l12 {};
+				pm8058_l13: l13 {};
+				pm8058_l14: l14 {};
+				pm8058_l15: l15 {};
+				pm8058_l16: l16 {};
+				pm8058_l17: l17 {};
+				pm8058_l18: l18 {};
+				pm8058_l19: l19 {};
+				pm8058_l20: l20 {};
+				pm8058_l21: l21 {};
+				pm8058_l22: l22 {};
+				pm8058_l23: l23 {};
+				pm8058_l24: l24 {};
+				pm8058_l25: l25 {};
+
+				pm8058_s0: s0 {};
+				pm8058_s1: s1 {};
+				pm8058_s2: s2 {};
+				pm8058_s3: s3 {};
+				pm8058_s4: s4 {};
+
+				pm8058_lvs0: lvs0 {};
+				pm8058_lvs1: lvs1 {};
+
+				pm8058_ncp: ncp {};
+			};
 		};
 
 		amba {
@@ -205,7 +334,6 @@
 				non-removable;
 				cap-sd-highspeed;
 				cap-mmc-highspeed;
-				vmmc-supply = <&vsdcc_fixed>;
 			};
 
 			sdcc3: sdcc@12180000 {
@@ -222,7 +350,21 @@
 				cap-mmc-highspeed;
 				max-frequency	= <48000000>;
 				no-1-8-v;
-				vmmc-supply = <&vsdcc_fixed>;
+			};
+
+			sdcc5: sdcc@12200000 {
+				compatible	= "arm,pl18x", "arm,primecell";
+				arm,primecell-periphid = <0x00051180>;
+				status		= "disabled";
+				reg		= <0x12200000 0x8000>;
+				interrupts	= <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names	= "cmd_irq";
+				clocks		= <&gcc SDC5_CLK>, <&gcc SDC5_H_CLK>;
+				clock-names	= "mclk", "apb_pclk";
+				bus-width	= <4>;
+				cap-sd-highspeed;
+				cap-mmc-highspeed;
+				max-frequency	= <48000000>;
 			};
 		};
 
diff --git a/arch/arm/boot/dts/qcom-msm8974-sony-xperia-honami.dts b/arch/arm/boot/dts/qcom-msm8974-sony-xperia-honami.dts
index a0398b6..3fb4dad 100644
--- a/arch/arm/boot/dts/qcom-msm8974-sony-xperia-honami.dts
+++ b/arch/arm/boot/dts/qcom-msm8974-sony-xperia-honami.dts
@@ -367,6 +367,10 @@
 		};
 
 	};
+
+	dma-controller@f9944000 {
+		qcom,controlled-remotely;
+	};
 };
 
 &spmi_bus {
diff --git a/arch/arm/boot/dts/qcom-msm8974.dtsi b/arch/arm/boot/dts/qcom-msm8974.dtsi
index 6f16426..561d4d1 100644
--- a/arch/arm/boot/dts/qcom-msm8974.dtsi
+++ b/arch/arm/boot/dts/qcom-msm8974.dtsi
@@ -1,6 +1,6 @@
 /dts-v1/;
 
-#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/clock/qcom,gcc-msm8974.h>
 #include "skeleton.dtsi"
 
@@ -182,7 +182,7 @@
 
 		modem_smp2p_out: master-kernel {
 			qcom,entry-name = "master-kernel";
-			#qcom,state-cells = <1>;
+			#qcom,smem-state-cells = <1>;
 		};
 
 		modem_smp2p_in: slave-kernel {
@@ -208,7 +208,7 @@
 		wcnss_smp2p_out: master-kernel {
 			qcom,entry-name = "master-kernel";
 
-			#qcom,state-cells = <1>;
+			#qcom,smem-state-cells = <1>;
 		};
 
 		wcnss_smp2p_in: slave-kernel {
@@ -232,7 +232,7 @@
 		apps_smsm: apps@0 {
 			reg = <0>;
 
-			#qcom,state-cells = <1>;
+			#qcom,smem-state-cells = <1>;
 		};
 
 		modem_smsm: modem@1 {
@@ -260,6 +260,14 @@
 		};
 	};
 
+	firmware {
+		scm {
+			compatible = "qcom,scm";
+			clocks = <&gcc GCC_CE1_CLK>, <&gcc GCC_CE1_AXI_CLK>, <&gcc GCC_CE1_AHB_CLK>;
+			clock-names = "core", "bus", "iface";
+		};
+	};
+
 	soc: soc {
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -501,6 +509,8 @@
 			clock-names = "core", "iface";
 			#address-cells = <1>;
 			#size-cells = <0>;
+			dmas = <&blsp2_dma 20>, <&blsp2_dma 21>;
+			dma-names = "tx", "rx";
 		};
 
 		spmi_bus: spmi@fc4cf000 {
@@ -518,6 +528,16 @@
 			interrupt-controller;
 			#interrupt-cells = <4>;
 		};
+
+		blsp2_dma: dma-controller@f9944000 {
+			compatible = "qcom,bam-v1.4.0";
+			reg = <0xf9944000 0x19000>;
+			interrupts = <GIC_SPI 239 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP2_AHB_CLK>;
+			clock-names = "bam_clk";
+			#dma-cells = <1>;
+			qcom,ee = <0>;
+		};
 	};
 
 	smd {
diff --git a/arch/arm/boot/dts/qcom-pma8084.dtsi b/arch/arm/boot/dts/qcom-pma8084.dtsi
index 4e9bd3f..82d2580 100644
--- a/arch/arm/boot/dts/qcom-pma8084.dtsi
+++ b/arch/arm/boot/dts/qcom-pma8084.dtsi
@@ -12,15 +12,23 @@
 
 		rtc@6000 {
 			compatible = "qcom,pm8941-rtc";
-			reg = <0x6000 0x100>,
-			      <0x6100 0x100>;
+			reg = <0x6000>,
+			      <0x6100>;
 			reg-names = "rtc", "alarm";
 			interrupts = <0x0 0x61 0x1 IRQ_TYPE_EDGE_RISING>;
 		};
 
+		pwrkey@800 {
+			compatible = "qcom,pm8941-pwrkey";
+			reg = <0x800>;
+			interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>;
+			debounce = <15625>;
+			bias-pull-up;
+		};
+
 		pma8084_gpios: gpios@c000 {
 			compatible = "qcom,pma8084-gpio", "qcom,spmi-gpio";
-			reg = <0xc000 0x1600>;
+			reg = <0xc000>;
 			gpio-controller;
 			#gpio-cells = <2>;
 			interrupts = <0 0xc0 0 IRQ_TYPE_NONE>,
@@ -49,7 +57,7 @@
 
 		pma8084_mpps: mpps@a000 {
 			compatible = "qcom,pma8084-mpp", "qcom,spmi-mpp";
-			reg = <0xa000 0x800>;
+			reg = <0xa000>;
 			gpio-controller;
 			#gpio-cells = <2>;
 			interrupts = <0 0xa0 0 IRQ_TYPE_NONE>,
@@ -64,7 +72,7 @@
 
 		pma8084_temp: temp-alarm@2400 {
 			compatible = "qcom,spmi-temp-alarm";
-			reg = <0x2400 0x100>;
+			reg = <0x2400>;
 			interrupts = <0 0x24 0 IRQ_TYPE_EDGE_RISING>;
 			#thermal-sensor-cells = <0>;
 			io-channels = <&pma8084_vadc VADC_DIE_TEMP>;
@@ -73,7 +81,7 @@
 
 		pma8084_vadc: vadc@3100 {
 			compatible = "qcom,spmi-vadc";
-			reg = <0x3100 0x100>;
+			reg = <0x3100>;
 			interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
 			#address-cells = <1>;
 			#size-cells = <0>;