ARM: OMAP2+: UART: Move errata handling from serial.c to omap-serial

Move the errata handling mechanism from serial.c to omap-serial file
and utilise the same func in driver file.

Errata i202, i291 are moved to be handled with omap-serial
Moving the errata macro from serial.c file to driver header file
as from on errata will be handled in driver file itself.
Corrected errata id from chapter reference 2.15 to errata id i291.

Removed errata and dma_enabled fields from omap_uart_state struct
as they are no more needed with errata handling done within omap-serial.

Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Kevin Hilman <khilman@ti.com>

2 files changed, 38 insertions, 70 deletions

diff --git a/arch/arm/mach-omap2/serial.c b/arch/arm/mach-omap2/serial.c
index 78ca7e8..77a25cb 100644
--- a/arch/arm/mach-omap2/serial.c
+++ b/arch/arm/mach-omap2/serial.c
@@ -42,8 +42,6 @@
 #include "control.h"
 #include "mux.h"
 
-#define UART_ERRATA_i202_MDR1_ACCESS	(0x1 << 1)
-
 /*
  * NOTE: By default the serial timeout is disabled as it causes lost characters
  * over the serial ports. This means that the UART clocks will stay on until
@@ -61,59 +59,17 @@ struct omap_uart_state {
 	void __iomem *wk_st;
 	void __iomem *wk_en;
 	u32 wk_mask;
-	u32 dma_enabled;
 
 	int clocked;
 
 	struct list_head node;
 	struct omap_hwmod *oh;
 	struct platform_device *pdev;
-
-	u32 errata;
 };
 
 static LIST_HEAD(uart_list);
 static u8 num_uarts;
 
-#if defined(CONFIG_PM) && defined(CONFIG_ARCH_OMAP3)
-
-/*
- * Work Around for Errata i202 (3430 - 1.12, 3630 - 1.6)
- * The access to uart register after MDR1 Access
- * causes UART to corrupt data.
- *
- * Need a delay =
- * 5 L4 clock cycles + 5 UART functional clock cycle (@48MHz = ~0.2uS)
- * give 10 times as much
- */
-static void omap_uart_mdr1_errataset(struct omap_uart_state *uart, u8 mdr1_val,
-		u8 fcr_val)
-{
-	u8 timeout = 255;
-
-	serial_write_reg(uart, UART_OMAP_MDR1, mdr1_val);
-	udelay(2);
-	serial_write_reg(uart, UART_FCR, fcr_val | UART_FCR_CLEAR_XMIT |
-			UART_FCR_CLEAR_RCVR);
-	/*
-	 * Wait for FIFO to empty: when empty, RX_FIFO_E bit is 0 and
-	 * TX_FIFO_E bit is 1.
-	 */
-	while (UART_LSR_THRE != (serial_read_reg(uart, UART_LSR) &
-				(UART_LSR_THRE | UART_LSR_DR))) {
-		timeout--;
-		if (!timeout) {
-			/* Should *never* happen. we warn and carry on */
-			dev_crit(&uart->pdev->dev, "Errata i202: timedout %x\n",
-			serial_read_reg(uart, UART_LSR));
-			break;
-		}
-		udelay(1);
-	}
-}
-
-#endif /* CONFIG_PM && CONFIG_ARCH_OMAP3 */
-
 static inline void omap_uart_enable_clocks(struct omap_uart_state *uart)
 {
 	if (uart->clocked)
@@ -156,27 +112,6 @@ static void omap_uart_disable_wakeup(struct omap_uart_state *uart)
 	}
 }
 
-static void omap_uart_smart_idle_enable(struct omap_uart_state *uart,
-					       int enable)
-{
-	u8 idlemode;
-
-	if (enable) {
-		/**
-		 * Errata 2.15: [UART]:Cannot Acknowledge Idle Requests
-		 * in Smartidle Mode When Configured for DMA Operations.
-		 */
-		if (uart->dma_enabled)
-			idlemode = HWMOD_IDLEMODE_FORCE;
-		else
-			idlemode = HWMOD_IDLEMODE_SMART;
-	} else {
-		idlemode = HWMOD_IDLEMODE_NO;
-	}
-
-	omap_hwmod_set_slave_idlemode(uart->oh, idlemode);
-}
-
 static void omap_uart_block_sleep(struct omap_uart_state *uart)
 {
 	omap_uart_enable_clocks(uart);
@@ -267,7 +202,28 @@ static void omap_uart_idle_init(struct omap_uart_state *uart)
 	}
 }
 
+/*
+ * Errata i291: [UART]:Cannot Acknowledge Idle Requests
+ * in Smartidle Mode When Configured for DMA Operations.
+ * WA: configure uart in force idle mode.
+ */
+static void omap_uart_set_noidle(struct platform_device *pdev)
+{
+	struct omap_device *od = to_omap_device(pdev);
+
+	omap_hwmod_set_slave_idlemode(od->hwmods[0], HWMOD_IDLEMODE_NO);
+}
+
+static void omap_uart_set_forceidle(struct platform_device *pdev)
+{
+	struct omap_device *od = to_omap_device(pdev);
+
+	omap_hwmod_set_slave_idlemode(od->hwmods[0], HWMOD_IDLEMODE_FORCE);
+}
+
 #else
+static void omap_uart_set_noidle(struct platform_device *pdev) {}
+static void omap_uart_set_forceidle(struct platform_device *pdev) {}
 static void omap_uart_block_sleep(struct omap_uart_state *uart)
 {
 	/* Needed to enable UART clocks when built without CONFIG_PM */
@@ -473,13 +429,22 @@ void __init omap_serial_init_port(struct omap_board_data *bdata)
 			break;
 
 	oh = uart->oh;
-	uart->dma_enabled = 0;
 	name = DRIVER_NAME;
 
 	omap_up.dma_enabled = uart->dma_enabled;
 	omap_up.uartclk = OMAP24XX_BASE_BAUD * 16;
 	omap_up.flags = UPF_BOOT_AUTOCONF;
 	omap_up.get_context_loss_count = omap_pm_get_dev_context_loss_count;
+	omap_up.set_forceidle = omap_uart_set_forceidle;
+	omap_up.set_noidle = omap_uart_set_noidle;
+
+	/* Enable the MDR1 Errata i202 for OMAP2430/3xxx/44xx */
+	if (!cpu_is_omap2420() && !cpu_is_ti816x())
+		omap_up.errata |= UART_ERRATA_i202_MDR1_ACCESS;
+
+	/* Enable DMA Mode Force Idle Errata i291 for omap34xx/3630 */
+	if (cpu_is_omap34xx() || cpu_is_omap3630())
+		omap_up.errata |= UART_ERRATA_i291_DMA_FORCEIDLE;
 
 	pdata = &omap_up;
 	pdata_size = sizeof(struct omap_uart_port_info);
@@ -519,10 +484,6 @@ void __init omap_serial_init_port(struct omap_board_data *bdata)
 	if (((cpu_is_omap34xx() || cpu_is_omap44xx()) && bdata->pads) ||
 		(pdata->wk_en && pdata->wk_mask))
 		device_init_wakeup(&pdev->dev, true);
-
-	/* Enable the MDR1 errata for OMAP3 */
-	if (cpu_is_omap34xx() && !(cpu_is_ti81xx() || cpu_is_am33xx()))
-		uart->errata |= UART_ERRATA_i202_MDR1_ACCESS;
 }
 
 /**
diff --git a/arch/arm/plat-omap/include/plat/omap-serial.h b/arch/arm/plat-omap/include/plat/omap-serial.h
index 348c9ea..842b429 100644
--- a/arch/arm/plat-omap/include/plat/omap-serial.h
+++ b/arch/arm/plat-omap/include/plat/omap-serial.h
@@ -58,12 +58,18 @@
 
 #define MSR_SAVE_FLAGS		UART_MSR_ANY_DELTA
 
+#define UART_ERRATA_i202_MDR1_ACCESS	BIT(0)
+#define UART_ERRATA_i291_DMA_FORCEIDLE	BIT(1)
+
 struct omap_uart_port_info {
 	bool			dma_enabled;	/* To specify DMA Mode */
 	unsigned int		uartclk;	/* UART clock rate */
 	upf_t			flags;		/* UPF_* flags */
+	u32			errata;
 
 	int (*get_context_loss_count)(struct device *);
+	void (*set_forceidle)(struct platform_device *);
+	void (*set_noidle)(struct platform_device *);
 };
 
 struct uart_omap_dma {
@@ -117,6 +123,7 @@ struct uart_omap_port {
 	char			name[20];
 	unsigned long		port_activity;
 	u32			context_loss_cnt;
+	u32			errata;
 };
 
 #endif /* __OMAP_SERIAL_H__ */