diff options
author | Jeff Kirsher <jeffrey.t.kirsher@intel.com> | 2011-10-07 22:07:44 (GMT) |
---|---|---|
committer | David S. Miller <davem@davemloft.net> | 2011-10-19 03:41:43 (GMT) |
commit | b340a207c5d81a0a33899e8ab3236a04dd8b48c3 (patch) | |
tree | 8f9662ca81cd9332c3f6da12733a904e9434af17 /drivers/net/ethernet/cirrus | |
parent | 09df57ca604512b29b6096afb381c839ccbd2912 (diff) | |
download | linux-b340a207c5d81a0a33899e8ab3236a04dd8b48c3.tar.xz |
cs89x0: Move the driver into the Cirrus dir
The cs89x0 driver was initial placed in the apple/ when it
should have been placed in the cirrus/. This resolves the
issue by moving the dirver and fixing up the respective
Kconfig(s) and Makefile(s).
Thanks to Sascha for reporting the issue.
-v2 Fix a config error that was introduced with v1 by removing
the dependency on MACE for NET_VENDOR_APPLE.
CC: Russell Nelson <nelson@crynwr.com>
CC: Andrew Morton <akpm@linux-foundation.org>
Reported-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Diffstat (limited to 'drivers/net/ethernet/cirrus')
-rw-r--r-- | drivers/net/ethernet/cirrus/Kconfig | 22 | ||||
-rw-r--r-- | drivers/net/ethernet/cirrus/Makefile | 1 | ||||
-rw-r--r-- | drivers/net/ethernet/cirrus/cs89x0.c | 1913 | ||||
-rw-r--r-- | drivers/net/ethernet/cirrus/cs89x0.h | 465 |
4 files changed, 2400 insertions, 1 deletions
diff --git a/drivers/net/ethernet/cirrus/Kconfig b/drivers/net/ethernet/cirrus/Kconfig index e9386ef..6cbb81c 100644 --- a/drivers/net/ethernet/cirrus/Kconfig +++ b/drivers/net/ethernet/cirrus/Kconfig @@ -5,7 +5,8 @@ config NET_VENDOR_CIRRUS bool "Cirrus devices" default y - depends on ARM && ARCH_EP93XX + depends on ISA || EISA || MACH_IXDP2351 || ARCH_IXDP2X01 \ + || MACH_MX31ADS || MACH_QQ2440 || (ARM && ARCH_EP93XX) ---help--- If you have a network (Ethernet) card belonging to this class, say Y and read the Ethernet-HOWTO, available from @@ -18,6 +19,25 @@ config NET_VENDOR_CIRRUS if NET_VENDOR_CIRRUS +config CS89x0 + tristate "CS89x0 support" + depends on (ISA || EISA || MACH_IXDP2351 \ + || ARCH_IXDP2X01 || MACH_MX31ADS || MACH_QQ2440) + ---help--- + Support for CS89x0 chipset based Ethernet cards. If you have a + network (Ethernet) card of this type, say Y and read the + Ethernet-HOWTO, available from + <http://www.tldp.org/docs.html#howto> as well as + <file:Documentation/networking/cs89x0.txt>. + + To compile this driver as a module, choose M here. The module + will be called cs89x0. + +config CS89x0_NONISA_IRQ + def_bool y + depends on CS89x0 != n + depends on MACH_IXDP2351 || ARCH_IXDP2X01 || MACH_MX31ADS || MACH_QQ2440 + config EP93XX_ETH tristate "EP93xx Ethernet support" depends on ARM && ARCH_EP93XX diff --git a/drivers/net/ethernet/cirrus/Makefile b/drivers/net/ethernet/cirrus/Makefile index 9905ea2..14bd77e 100644 --- a/drivers/net/ethernet/cirrus/Makefile +++ b/drivers/net/ethernet/cirrus/Makefile @@ -2,4 +2,5 @@ # Makefile for the Cirrus network device drivers. # +obj-$(CONFIG_CS89x0) += cs89x0.o obj-$(CONFIG_EP93XX_ETH) += ep93xx_eth.o diff --git a/drivers/net/ethernet/cirrus/cs89x0.c b/drivers/net/ethernet/cirrus/cs89x0.c new file mode 100644 index 0000000..f328da2 --- /dev/null +++ b/drivers/net/ethernet/cirrus/cs89x0.c @@ -0,0 +1,1913 @@ +/* cs89x0.c: A Crystal Semiconductor (Now Cirrus Logic) CS89[02]0 + * driver for linux. + */ + +/* + Written 1996 by Russell Nelson, with reference to skeleton.c + written 1993-1994 by Donald Becker. + + This software may be used and distributed according to the terms + of the GNU General Public License, incorporated herein by reference. + + The author may be reached at nelson@crynwr.com, Crynwr + Software, 521 Pleasant Valley Rd., Potsdam, NY 13676 + + Changelog: + + Mike Cruse : mcruse@cti-ltd.com + : Changes for Linux 2.0 compatibility. + : Added dev_id parameter in net_interrupt(), + : request_irq() and free_irq(). Just NULL for now. + + Mike Cruse : Added MOD_INC_USE_COUNT and MOD_DEC_USE_COUNT macros + : in net_open() and net_close() so kerneld would know + : that the module is in use and wouldn't eject the + : driver prematurely. + + Mike Cruse : Rewrote init_module() and cleanup_module using 8390.c + : as an example. Disabled autoprobing in init_module(), + : not a good thing to do to other devices while Linux + : is running from all accounts. + + Russ Nelson : Jul 13 1998. Added RxOnly DMA support. + + Melody Lee : Aug 10 1999. Changes for Linux 2.2.5 compatibility. + : email: ethernet@crystal.cirrus.com + + Alan Cox : Removed 1.2 support, added 2.1 extra counters. + + Andrew Morton : Kernel 2.3.48 + : Handle kmalloc() failures + : Other resource allocation fixes + : Add SMP locks + : Integrate Russ Nelson's ALLOW_DMA functionality back in. + : If ALLOW_DMA is true, make DMA runtime selectable + : Folded in changes from Cirrus (Melody Lee + : <klee@crystal.cirrus.com>) + : Don't call netif_wake_queue() in net_send_packet() + : Fixed an out-of-mem bug in dma_rx() + : Updated Documentation/networking/cs89x0.txt + + Andrew Morton : Kernel 2.3.99-pre1 + : Use skb_reserve to longword align IP header (two places) + : Remove a delay loop from dma_rx() + : Replace '100' with HZ + : Clean up a couple of skb API abuses + : Added 'cs89x0_dma=N' kernel boot option + : Correctly initialise lp->lock in non-module compile + + Andrew Morton : Kernel 2.3.99-pre4-1 + : MOD_INC/DEC race fix (see + : http://www.uwsg.indiana.edu/hypermail/linux/kernel/0003.3/1532.html) + + Andrew Morton : Kernel 2.4.0-test7-pre2 + : Enhanced EEPROM support to cover more devices, + : abstracted IRQ mapping to support CONFIG_ARCH_CLPS7500 arch + : (Jason Gunthorpe <jgg@ualberta.ca>) + + Andrew Morton : Kernel 2.4.0-test11-pre4 + : Use dev->name in request_*() (Andrey Panin) + : Fix an error-path memleak in init_module() + : Preserve return value from request_irq() + : Fix type of `media' module parm (Keith Owens) + : Use SET_MODULE_OWNER() + : Tidied up strange request_irq() abuse in net_open(). + + Andrew Morton : Kernel 2.4.3-pre1 + : Request correct number of pages for DMA (Hugh Dickens) + : Select PP_ChipID _after_ unregister_netdev in cleanup_module() + : because unregister_netdev() calls get_stats. + : Make `version[]' __initdata + : Uninlined the read/write reg/word functions. + + Oskar Schirmer : oskar@scara.com + : HiCO.SH4 (superh) support added (irq#1, cs89x0_media=) + + Deepak Saxena : dsaxena@plexity.net + : Intel IXDP2x01 (XScale ixp2x00 NPU) platform support + + Dmitry Pervushin : dpervushin@ru.mvista.com + : PNX010X platform support + + Deepak Saxena : dsaxena@plexity.net + : Intel IXDP2351 platform support + + Dmitry Pervushin : dpervushin@ru.mvista.com + : PNX010X platform support + + Domenico Andreoli : cavokz@gmail.com + : QQ2440 platform support + +*/ + +/* Always include 'config.h' first in case the user wants to turn on + or override something. */ +#include <linux/module.h> + +/* + * Set this to zero to disable DMA code + * + * Note that even if DMA is turned off we still support the 'dma' and 'use_dma' + * module options so we don't break any startup scripts. + */ +#ifndef CONFIG_ISA_DMA_API +#define ALLOW_DMA 0 +#else +#define ALLOW_DMA 1 +#endif + +/* + * Set this to zero to remove all the debug statements via + * dead code elimination + */ +#define DEBUGGING 1 + +/* + Sources: + + Crynwr packet driver epktisa. + + Crystal Semiconductor data sheets. + +*/ + +#include <linux/errno.h> +#include <linux/netdevice.h> +#include <linux/etherdevice.h> +#include <linux/kernel.h> +#include <linux/types.h> +#include <linux/fcntl.h> +#include <linux/interrupt.h> +#include <linux/ioport.h> +#include <linux/in.h> +#include <linux/skbuff.h> +#include <linux/spinlock.h> +#include <linux/string.h> +#include <linux/init.h> +#include <linux/bitops.h> +#include <linux/delay.h> +#include <linux/gfp.h> + +#include <asm/system.h> +#include <asm/io.h> +#include <asm/irq.h> +#if ALLOW_DMA +#include <asm/dma.h> +#endif + +#include "cs89x0.h" + +static char version[] __initdata = +"cs89x0.c: v2.4.3-pre1 Russell Nelson <nelson@crynwr.com>, Andrew Morton\n"; + +#define DRV_NAME "cs89x0" + +/* First, a few definitions that the brave might change. + A zero-terminated list of I/O addresses to be probed. Some special flags.. + Addr & 1 = Read back the address port, look for signature and reset + the page window before probing + Addr & 3 = Reset the page window and probe + The CLPS eval board has the Cirrus chip at 0x80090300, in ARM IO space, + but it is possible that a Cirrus board could be plugged into the ISA + slots. */ +/* The cs8900 has 4 IRQ pins, software selectable. cs8900_irq_map maps + them to system IRQ numbers. This mapping is card specific and is set to + the configuration of the Cirrus Eval board for this chip. */ +#if defined(CONFIG_MACH_IXDP2351) +static unsigned int netcard_portlist[] __used __initdata = {IXDP2351_VIRT_CS8900_BASE, 0}; +static unsigned int cs8900_irq_map[] = {IRQ_IXDP2351_CS8900, 0, 0, 0}; +#elif defined(CONFIG_ARCH_IXDP2X01) +static unsigned int netcard_portlist[] __used __initdata = {IXDP2X01_CS8900_VIRT_BASE, 0}; +static unsigned int cs8900_irq_map[] = {IRQ_IXDP2X01_CS8900, 0, 0, 0}; +#elif defined(CONFIG_MACH_QQ2440) +#include <mach/qq2440.h> +static unsigned int netcard_portlist[] __used __initdata = { QQ2440_CS8900_VIRT_BASE + 0x300, 0 }; +static unsigned int cs8900_irq_map[] = { QQ2440_CS8900_IRQ, 0, 0, 0 }; +#elif defined(CONFIG_MACH_MX31ADS) +#include <mach/board-mx31ads.h> +static unsigned int netcard_portlist[] __used __initdata = { + PBC_BASE_ADDRESS + PBC_CS8900A_IOBASE + 0x300, 0 +}; +static unsigned cs8900_irq_map[] = {EXPIO_INT_ENET_INT, 0, 0, 0}; +#else +static unsigned int netcard_portlist[] __used __initdata = + { 0x300, 0x320, 0x340, 0x360, 0x200, 0x220, 0x240, 0x260, 0x280, 0x2a0, 0x2c0, 0x2e0, 0}; +static unsigned int cs8900_irq_map[] = {10,11,12,5}; +#endif + +#if DEBUGGING +static unsigned int net_debug = DEBUGGING; +#else +#define net_debug 0 /* gcc will remove all the debug code for us */ +#endif + +/* The number of low I/O ports used by the ethercard. */ +#define NETCARD_IO_EXTENT 16 + +/* we allow the user to override various values normally set in the EEPROM */ +#define FORCE_RJ45 0x0001 /* pick one of these three */ +#define FORCE_AUI 0x0002 +#define FORCE_BNC 0x0004 + +#define FORCE_AUTO 0x0010 /* pick one of these three */ +#define FORCE_HALF 0x0020 +#define FORCE_FULL 0x0030 + +/* Information that need to be kept for each board. */ +struct net_local { + int chip_type; /* one of: CS8900, CS8920, CS8920M */ + char chip_revision; /* revision letter of the chip ('A'...) */ + int send_cmd; /* the proper send command: TX_NOW, TX_AFTER_381, or TX_AFTER_ALL */ + int auto_neg_cnf; /* auto-negotiation word from EEPROM */ + int adapter_cnf; /* adapter configuration from EEPROM */ + int isa_config; /* ISA configuration from EEPROM */ + int irq_map; /* IRQ map from EEPROM */ + int rx_mode; /* what mode are we in? 0, RX_MULTCAST_ACCEPT, or RX_ALL_ACCEPT */ + int curr_rx_cfg; /* a copy of PP_RxCFG */ + int linectl; /* either 0 or LOW_RX_SQUELCH, depending on configuration. */ + int send_underrun; /* keep track of how many underruns in a row we get */ + int force; /* force various values; see FORCE* above. */ + spinlock_t lock; +#if ALLOW_DMA + int use_dma; /* Flag: we're using dma */ + int dma; /* DMA channel */ + int dmasize; /* 16 or 64 */ + unsigned char *dma_buff; /* points to the beginning of the buffer */ + unsigned char *end_dma_buff; /* points to the end of the buffer */ + unsigned char *rx_dma_ptr; /* points to the next packet */ +#endif +}; + +/* Index to functions, as function prototypes. */ + +static int cs89x0_probe1(struct net_device *dev, int ioaddr, int modular); +static int net_open(struct net_device *dev); +static netdev_tx_t net_send_packet(struct sk_buff *skb, struct net_device *dev); +static irqreturn_t net_interrupt(int irq, void *dev_id); +static void set_multicast_list(struct net_device *dev); +static void net_timeout(struct net_device *dev); +static void net_rx(struct net_device *dev); +static int net_close(struct net_device *dev); +static struct net_device_stats *net_get_stats(struct net_device *dev); +static void reset_chip(struct net_device *dev); +static int get_eeprom_data(struct net_device *dev, int off, int len, int *buffer); +static int get_eeprom_cksum(int off, int len, int *buffer); +static int set_mac_address(struct net_device *dev, void *addr); +static void count_rx_errors(int status, struct net_device *dev); +#ifdef CONFIG_NET_POLL_CONTROLLER +static void net_poll_controller(struct net_device *dev); +#endif +#if ALLOW_DMA +static void get_dma_channel(struct net_device *dev); +static void release_dma_buff(struct net_local *lp); +#endif + +/* Example routines you must write ;->. */ +#define tx_done(dev) 1 + +/* + * Permit 'cs89x0_dma=N' in the kernel boot environment + */ +#if !defined(MODULE) && (ALLOW_DMA != 0) +static int g_cs89x0_dma; + +static int __init dma_fn(char *str) +{ + g_cs89x0_dma = simple_strtol(str,NULL,0); + return 1; +} + +__setup("cs89x0_dma=", dma_fn); +#endif /* !defined(MODULE) && (ALLOW_DMA != 0) */ + +#ifndef MODULE +static int g_cs89x0_media__force; + +static int __init media_fn(char *str) +{ + if (!strcmp(str, "rj45")) g_cs89x0_media__force = FORCE_RJ45; + else if (!strcmp(str, "aui")) g_cs89x0_media__force = FORCE_AUI; + else if (!strcmp(str, "bnc")) g_cs89x0_media__force = FORCE_BNC; + return 1; +} + +__setup("cs89x0_media=", media_fn); + + +/* Check for a network adaptor of this type, and return '0' iff one exists. + If dev->base_addr == 0, probe all likely locations. + If dev->base_addr == 1, always return failure. + If dev->base_addr == 2, allocate space for the device and return success + (detachable devices only). + Return 0 on success. + */ + +struct net_device * __init cs89x0_probe(int unit) +{ + struct net_device *dev = alloc_etherdev(sizeof(struct net_local)); + unsigned *port; + int err = 0; + int irq; + int io; + + if (!dev) + return ERR_PTR(-ENODEV); + + sprintf(dev->name, "eth%d", unit); + netdev_boot_setup_check(dev); + io = dev->base_addr; + irq = dev->irq; + + if (net_debug) + printk("cs89x0:cs89x0_probe(0x%x)\n", io); + + if (io > 0x1ff) { /* Check a single specified location. */ + err = cs89x0_probe1(dev, io, 0); + } else if (io != 0) { /* Don't probe at all. */ + err = -ENXIO; + } else { + for (port = netcard_portlist; *port; port++) { + if (cs89x0_probe1(dev, *port, 0) == 0) + break; + dev->irq = irq; + } + if (!*port) + err = -ENODEV; + } + if (err) + goto out; + return dev; +out: + free_netdev(dev); + printk(KERN_WARNING "cs89x0: no cs8900 or cs8920 detected. Be sure to disable PnP with SETUP\n"); + return ERR_PTR(err); +} +#endif + +#if defined(CONFIG_MACH_IXDP2351) +static u16 +readword(unsigned long base_addr, int portno) +{ + return __raw_readw(base_addr + (portno << 1)); +} + +static void +writeword(unsigned long base_addr, int portno, u16 value) +{ + __raw_writew(value, base_addr + (portno << 1)); +} +#elif defined(CONFIG_ARCH_IXDP2X01) +static u16 +readword(unsigned long base_addr, int portno) +{ + return __raw_readl(base_addr + (portno << 1)); +} + +static void +writeword(unsigned long base_addr, int portno, u16 value) +{ + __raw_writel(value, base_addr + (portno << 1)); +} +#else +static u16 +readword(unsigned long base_addr, int portno) +{ + return inw(base_addr + portno); +} + +static void +writeword(unsigned long base_addr, int portno, u16 value) +{ + outw(value, base_addr + portno); +} +#endif + +static void +readwords(unsigned long base_addr, int portno, void *buf, int length) +{ + u8 *buf8 = (u8 *)buf; + + do { + u16 tmp16; + + tmp16 = readword(base_addr, portno); + *buf8++ = (u8)tmp16; + *buf8++ = (u8)(tmp16 >> 8); + } while (--length); +} + +static void +writewords(unsigned long base_addr, int portno, void *buf, int length) +{ + u8 *buf8 = (u8 *)buf; + + do { + u16 tmp16; + + tmp16 = *buf8++; + tmp16 |= (*buf8++) << 8; + writeword(base_addr, portno, tmp16); + } while (--length); +} + +static u16 +readreg(struct net_device *dev, u16 regno) +{ + writeword(dev->base_addr, ADD_PORT, regno); + return readword(dev->base_addr, DATA_PORT); +} + +static void +writereg(struct net_device *dev, u16 regno, u16 value) +{ + writeword(dev->base_addr, ADD_PORT, regno); + writeword(dev->base_addr, DATA_PORT, value); +} + +static int __init +wait_eeprom_ready(struct net_device *dev) +{ + int timeout = jiffies; + /* check to see if the EEPROM is ready, a timeout is used - + just in case EEPROM is ready when SI_BUSY in the + PP_SelfST is clear */ + while(readreg(dev, PP_SelfST) & SI_BUSY) + if (jiffies - timeout >= 40) + return -1; + return 0; +} + +static int __init +get_eeprom_data(struct net_device *dev, int off, int len, int *buffer) +{ + int i; + + if (net_debug > 3) printk("EEPROM data from %x for %x:\n",off,len); + for (i = 0; i < len; i++) { + if (wait_eeprom_ready(dev) < 0) return -1; + /* Now send the EEPROM read command and EEPROM location to read */ + writereg(dev, PP_EECMD, (off + i) | EEPROM_READ_CMD); + if (wait_eeprom_ready(dev) < 0) return -1; + buffer[i] = readreg(dev, PP_EEData); + if (net_debug > 3) printk("%04x ", buffer[i]); + } + if (net_debug > 3) printk("\n"); + return 0; +} + +static int __init +get_eeprom_cksum(int off, int len, int *buffer) +{ + int i, cksum; + + cksum = 0; + for (i = 0; i < len; i++) + cksum += buffer[i]; + cksum &= 0xffff; + if (cksum == 0) + return 0; + return -1; +} + +#ifdef CONFIG_NET_POLL_CONTROLLER +/* + * Polling receive - used by netconsole and other diagnostic tools + * to allow network i/o with interrupts disabled. + */ +static void net_poll_controller(struct net_device *dev) +{ + disable_irq(dev->irq); + net_interrupt(dev->irq, dev); + enable_irq(dev->irq); +} +#endif + +static const struct net_device_ops net_ops = { + .ndo_open = net_open, + .ndo_stop = net_close, + .ndo_tx_timeout = net_timeout, + .ndo_start_xmit = net_send_packet, + .ndo_get_stats = net_get_stats, + .ndo_set_rx_mode = set_multicast_list, + .ndo_set_mac_address = set_mac_address, +#ifdef CONFIG_NET_POLL_CONTROLLER + .ndo_poll_controller = net_poll_controller, +#endif + .ndo_change_mtu = eth_change_mtu, + .ndo_validate_addr = eth_validate_addr, +}; + +/* This is the real probe routine. Linux has a history of friendly device + probes on the ISA bus. A good device probes avoids doing writes, and + verifies that the correct device exists and functions. + Return 0 on success. + */ + +static int __init +cs89x0_probe1(struct net_device *dev, int ioaddr, int modular) +{ + struct net_local *lp = netdev_priv(dev); + static unsigned version_printed; + int i; + int tmp; + unsigned rev_type = 0; + int eeprom_buff[CHKSUM_LEN]; + int retval; + + /* Initialize the device structure. */ + if (!modular) { + memset(lp, 0, sizeof(*lp)); + spin_lock_init(&lp->lock); +#ifndef MODULE +#if ALLOW_DMA + if (g_cs89x0_dma) { + lp->use_dma = 1; + lp->dma = g_cs89x0_dma; + lp->dmasize = 16; /* Could make this an option... */ + } +#endif + lp->force = g_cs89x0_media__force; +#endif + +#if defined(CONFIG_MACH_QQ2440) + lp->force |= FORCE_RJ45 | FORCE_FULL; +#endif + } + + /* Grab the region so we can find another board if autoIRQ fails. */ + /* WTF is going on here? */ + if (!request_region(ioaddr & ~3, NETCARD_IO_EXTENT, DRV_NAME)) { + printk(KERN_ERR "%s: request_region(0x%x, 0x%x) failed\n", + DRV_NAME, ioaddr, NETCARD_IO_EXTENT); + retval = -EBUSY; + goto out1; + } + + /* if they give us an odd I/O address, then do ONE write to + the address port, to get it back to address zero, where we + expect to find the EISA signature word. An IO with a base of 0x3 + will skip the test for the ADD_PORT. */ + if (ioaddr & 1) { + if (net_debug > 1) + printk(KERN_INFO "%s: odd ioaddr 0x%x\n", dev->name, ioaddr); + if ((ioaddr & 2) != 2) + if ((readword(ioaddr & ~3, ADD_PORT) & ADD_MASK) != ADD_SIG) { + printk(KERN_ERR "%s: bad signature 0x%x\n", + dev->name, readword(ioaddr & ~3, ADD_PORT)); + retval = -ENODEV; + goto out2; + } + } + + ioaddr &= ~3; + printk(KERN_DEBUG "PP_addr at %x[%x]: 0x%x\n", + ioaddr, ADD_PORT, readword(ioaddr, ADD_PORT)); + writeword(ioaddr, ADD_PORT, PP_ChipID); + + tmp = readword(ioaddr, DATA_PORT); + if (tmp != CHIP_EISA_ID_SIG) { + printk(KERN_DEBUG "%s: incorrect signature at %x[%x]: 0x%x!=" + CHIP_EISA_ID_SIG_STR "\n", + dev->name, ioaddr, DATA_PORT, tmp); + retval = -ENODEV; + goto out2; + } + + /* Fill in the 'dev' fields. */ + dev->base_addr = ioaddr; + + /* get the chip type */ + rev_type = readreg(dev, PRODUCT_ID_ADD); + lp->chip_type = rev_type &~ REVISON_BITS; + lp->chip_revision = ((rev_type & REVISON_BITS) >> 8) + 'A'; + + /* Check the chip type and revision in order to set the correct send command + CS8920 revision C and CS8900 revision F can use the faster send. */ + lp->send_cmd = TX_AFTER_381; + if (lp->chip_type == CS8900 && lp->chip_revision >= 'F') + lp->send_cmd = TX_NOW; + if (lp->chip_type != CS8900 && lp->chip_revision >= 'C') + lp->send_cmd = TX_NOW; + + if (net_debug && version_printed++ == 0) + printk(version); + + printk(KERN_INFO "%s: cs89%c0%s rev %c found at %#3lx ", + dev->name, + lp->chip_type==CS8900?'0':'2', + lp->chip_type==CS8920M?"M":"", + lp->chip_revision, + dev->base_addr); + + reset_chip(dev); + + /* Here we read the current configuration of the chip. If there + is no Extended EEPROM then the idea is to not disturb the chip + configuration, it should have been correctly setup by automatic + EEPROM read on reset. So, if the chip says it read the EEPROM + the driver will always do *something* instead of complain that + adapter_cnf is 0. */ + + + if ((readreg(dev, PP_SelfST) & (EEPROM_OK | EEPROM_PRESENT)) == + (EEPROM_OK|EEPROM_PRESENT)) { + /* Load the MAC. */ + for (i=0; i < ETH_ALEN/2; i++) { + unsigned int Addr; + Addr = readreg(dev, PP_IA+i*2); + dev->dev_addr[i*2] = Addr & 0xFF; + dev->dev_addr[i*2+1] = Addr >> 8; + } + + /* Load the Adapter Configuration. + Note: Barring any more specific information from some + other source (ie EEPROM+Schematics), we would not know + how to operate a 10Base2 interface on the AUI port. + However, since we do read the status of HCB1 and use + settings that always result in calls to control_dc_dc(dev,0) + a BNC interface should work if the enable pin + (dc/dc converter) is on HCB1. It will be called AUI + however. */ + + lp->adapter_cnf = 0; + i = readreg(dev, PP_LineCTL); + /* Preserve the setting of the HCB1 pin. */ + if ((i & (HCB1 | HCB1_ENBL)) == (HCB1 | HCB1_ENBL)) + lp->adapter_cnf |= A_CNF_DC_DC_POLARITY; + /* Save the sqelch bit */ + if ((i & LOW_RX_SQUELCH) == LOW_RX_SQUELCH) + lp->adapter_cnf |= A_CNF_EXTND_10B_2 | A_CNF_LOW_RX_SQUELCH; + /* Check if the card is in 10Base-t only mode */ + if ((i & (AUI_ONLY | AUTO_AUI_10BASET)) == 0) + lp->adapter_cnf |= A_CNF_10B_T | A_CNF_MEDIA_10B_T; + /* Check if the card is in AUI only mode */ + if ((i & (AUI_ONLY | AUTO_AUI_10BASET)) == AUI_ONLY) + lp->adapter_cnf |= A_CNF_AUI | A_CNF_MEDIA_AUI; + /* Check if the card is in Auto mode. */ + if ((i & (AUI_ONLY | AUTO_AUI_10BASET)) == AUTO_AUI_10BASET) + lp->adapter_cnf |= A_CNF_AUI | A_CNF_10B_T | + A_CNF_MEDIA_AUI | A_CNF_MEDIA_10B_T | A_CNF_MEDIA_AUTO; + + if (net_debug > 1) + printk(KERN_INFO "%s: PP_LineCTL=0x%x, adapter_cnf=0x%x\n", + dev->name, i, lp->adapter_cnf); + + /* IRQ. Other chips already probe, see below. */ + if (lp->chip_type == CS8900) + lp->isa_config = readreg(dev, PP_CS8900_ISAINT) & INT_NO_MASK; + + printk( "[Cirrus EEPROM] "); + } + + printk("\n"); + + /* First check to see if an EEPROM is attached. */ + + if ((readreg(dev, PP_SelfST) & EEPROM_PRESENT) == 0) + printk(KERN_WARNING "cs89x0: No EEPROM, relying on command line....\n"); + else if (get_eeprom_data(dev, START_EEPROM_DATA,CHKSUM_LEN,eeprom_buff) < 0) { + printk(KERN_WARNING "\ncs89x0: EEPROM read failed, relying on command line.\n"); + } else if (get_eeprom_cksum(START_EEPROM_DATA,CHKSUM_LEN,eeprom_buff) < 0) { + /* Check if the chip was able to read its own configuration starting + at 0 in the EEPROM*/ + if ((readreg(dev, PP_SelfST) & (EEPROM_OK | EEPROM_PRESENT)) != + (EEPROM_OK|EEPROM_PRESENT)) + printk(KERN_WARNING "cs89x0: Extended EEPROM checksum bad and no Cirrus EEPROM, relying on command line\n"); + + } else { + /* This reads an extended EEPROM that is not documented + in the CS8900 datasheet. */ + + /* get transmission control word but keep the autonegotiation bits */ + if (!lp->auto_neg_cnf) lp->auto_neg_cnf = eeprom_buff[AUTO_NEG_CNF_OFFSET/2]; + /* Store adapter configuration */ + if (!lp->adapter_cnf) lp->adapter_cnf = eeprom_buff[ADAPTER_CNF_OFFSET/2]; + /* Store ISA configuration */ + lp->isa_config = eeprom_buff[ISA_CNF_OFFSET/2]; + dev->mem_start = eeprom_buff[PACKET_PAGE_OFFSET/2] << 8; + + /* eeprom_buff has 32-bit ints, so we can't just memcpy it */ + /* store the initial memory base address */ + for (i = 0; i < ETH_ALEN/2; i++) { + dev->dev_addr[i*2] = eeprom_buff[i]; + dev->dev_addr[i*2+1] = eeprom_buff[i] >> 8; + } + if (net_debug > 1) + printk(KERN_DEBUG "%s: new adapter_cnf: 0x%x\n", + dev->name, lp->adapter_cnf); + } + + /* allow them to force multiple transceivers. If they force multiple, autosense */ + { + int count = 0; + if (lp->force & FORCE_RJ45) {lp->adapter_cnf |= A_CNF_10B_T; count++; } + if (lp->force & FORCE_AUI) {lp->adapter_cnf |= A_CNF_AUI; count++; } + if (lp->force & FORCE_BNC) {lp->adapter_cnf |= A_CNF_10B_2; count++; } + if (count > 1) {lp->adapter_cnf |= A_CNF_MEDIA_AUTO; } + else if (lp->force & FORCE_RJ45){lp->adapter_cnf |= A_CNF_MEDIA_10B_T; } + else if (lp->force & FORCE_AUI) {lp->adapter_cnf |= A_CNF_MEDIA_AUI; } + else if (lp->force & FORCE_BNC) {lp->adapter_cnf |= A_CNF_MEDIA_10B_2; } + } + + if (net_debug > 1) + printk(KERN_DEBUG "%s: after force 0x%x, adapter_cnf=0x%x\n", + dev->name, lp->force, lp->adapter_cnf); + + /* FIXME: We don't let you set dc-dc polarity or low RX squelch from the command line: add it here */ + + /* FIXME: We don't let you set the IMM bit from the command line: add it to lp->auto_neg_cnf here */ + + /* FIXME: we don't set the Ethernet address on the command line. Use + ifconfig IFACE hw ether AABBCCDDEEFF */ + + printk(KERN_INFO "cs89x0 media %s%s%s", + (lp->adapter_cnf & A_CNF_10B_T)?"RJ-45,":"", + (lp->adapter_cnf & A_CNF_AUI)?"AUI,":"", + (lp->adapter_cnf & A_CNF_10B_2)?"BNC,":""); + + lp->irq_map = 0xffff; + + /* If this is a CS8900 then no pnp soft */ + if (lp->chip_type != CS8900 && + /* Check if the ISA IRQ has been set */ + (i = readreg(dev, PP_CS8920_ISAINT) & 0xff, + (i != 0 && i < CS8920_NO_INTS))) { + if (!dev->irq) + dev->irq = i; + } else { + i = lp->isa_config & INT_NO_MASK; + if (lp->chip_type == CS8900) { +#ifdef CONFIG_CS89x0_NONISA_IRQ + i = cs8900_irq_map[0]; +#else + /* Translate the IRQ using the IRQ mapping table. */ + if (i >= ARRAY_SIZE(cs8900_irq_map)) + printk("\ncs89x0: invalid ISA interrupt number %d\n", i); + else + i = cs8900_irq_map[i]; + + lp->irq_map = CS8900_IRQ_MAP; /* fixed IRQ map for CS8900 */ + } else { + int irq_map_buff[IRQ_MAP_LEN/2]; + + if (get_eeprom_data(dev, IRQ_MAP_EEPROM_DATA, + IRQ_MAP_LEN/2, + irq_map_buff) >= 0) { + if ((irq_map_buff[0] & 0xff) == PNP_IRQ_FRMT) + lp->irq_map = (irq_map_buff[0]>>8) | (irq_map_buff[1] << 8); + } +#endif + } + if (!dev->irq) + dev->irq = i; + } + + printk(" IRQ %d", dev->irq); + +#if ALLOW_DMA + if (lp->use_dma) { + get_dma_channel(dev); + printk(", DMA %d", dev->dma); + } + else +#endif + { + printk(", programmed I/O"); + } + + /* print the ethernet address. */ + printk(", MAC %pM", dev->dev_addr); + + dev->netdev_ops = &net_ops; + dev->watchdog_timeo = HZ; + + printk("\n"); + if (net_debug) + printk("cs89x0_probe1() successful\n"); + + retval = register_netdev(dev); + if (retval) + goto out3; + return 0; +out3: + writeword(dev->base_addr, ADD_PORT, PP_ChipID); +out2: + release_region(ioaddr & ~3, NETCARD_IO_EXTENT); +out1: + return retval; +} + + +/********************************* + * This page contains DMA routines +**********************************/ + +#if ALLOW_DMA + +#define dma_page_eq(ptr1, ptr2) ((long)(ptr1)>>17 == (long)(ptr2)>>17) + +static void +get_dma_channel(struct net_device *dev) +{ + struct net_local *lp = netdev_priv(dev); + + if (lp->dma) { + dev->dma = lp->dma; + lp->isa_config |= ISA_RxDMA; + } else { + if ((lp->isa_config & ANY_ISA_DMA) == 0) + return; + dev->dma = lp->isa_config & DMA_NO_MASK; + if (lp->chip_type == CS8900) + dev->dma += 5; + if (dev->dma < 5 || dev->dma > 7) { + lp->isa_config &= ~ANY_ISA_DMA; + return; + } + } +} + +static void +write_dma(struct net_device *dev, int chip_type, int dma) +{ + struct net_local *lp = netdev_priv(dev); + if ((lp->isa_config & ANY_ISA_DMA) == 0) + return; + if (chip_type == CS8900) { + writereg(dev, PP_CS8900_ISADMA, dma-5); + } else { + writereg(dev, PP_CS8920_ISADMA, dma); + } +} + +static void +set_dma_cfg(struct net_device *dev) +{ + struct net_local *lp = netdev_priv(dev); + + if (lp->use_dma) { + if ((lp->isa_config & ANY_ISA_DMA) == 0) { + if (net_debug > 3) + printk("set_dma_cfg(): no DMA\n"); + return; + } + if (lp->isa_config & ISA_RxDMA) { + lp->curr_rx_cfg |= RX_DMA_ONLY; + if (net_debug > 3) + printk("set_dma_cfg(): RX_DMA_ONLY\n"); + } else { + lp->curr_rx_cfg |= AUTO_RX_DMA; /* not that we support it... */ + if (net_debug > 3) + printk("set_dma_cfg(): AUTO_RX_DMA\n"); + } + } +} + +static int +dma_bufcfg(struct net_device *dev) +{ + struct net_local *lp = netdev_priv(dev); + if (lp->use_dma) + return (lp->isa_config & ANY_ISA_DMA)? RX_DMA_ENBL : 0; + else + return 0; +} + +static int +dma_busctl(struct net_device *dev) +{ + int retval = 0; + struct net_local *lp = netdev_priv(dev); + if (lp->use_dma) { + if (lp->isa_config & ANY_ISA_DMA) + retval |= RESET_RX_DMA; /* Reset the DMA pointer */ + if (lp->isa_config & DMA_BURST) + retval |= DMA_BURST_MODE; /* Does ISA config specify DMA burst ? */ + if (lp->dmasize == 64) + retval |= RX_DMA_SIZE_64K; /* did they ask for 64K? */ + retval |= MEMORY_ON; /* we need memory enabled to use DMA. */ + } + return retval; +} + +static void +dma_rx(struct net_device *dev) +{ + struct net_local *lp = netdev_priv(dev); + struct sk_buff *skb; + int status, length; + unsigned char *bp = lp->rx_dma_ptr; + + status = bp[0] + (bp[1]<<8); + length = bp[2] + (bp[3]<<8); + bp += 4; + if (net_debug > 5) { + printk( "%s: receiving DMA packet at %lx, status %x, length %x\n", + dev->name, (unsigned long)bp, status, length); + } + if ((status & RX_OK) == 0) { + count_rx_errors(status, dev); + goto skip_this_frame; + } + + /* Malloc up new buffer. */ + skb = dev_alloc_skb(length + 2); + if (skb == NULL) { + if (net_debug) /* I don't think we want to do this to a stressed system */ + printk("%s: Memory squeeze, dropping packet.\n", dev->name); + dev->stats.rx_dropped++; + + /* AKPM: advance bp to the next frame */ +skip_this_frame: + bp += (length + 3) & ~3; + if (bp >= lp->end_dma_buff) bp -= lp->dmasize*1024; + lp->rx_dma_ptr = bp; + return; + } + skb_reserve(skb, 2); /* longword align L3 header */ + + if (bp + length > lp->end_dma_buff) { + int semi_cnt = lp->end_dma_buff - bp; + memcpy(skb_put(skb,semi_cnt), bp, semi_cnt); + memcpy(skb_put(skb,length - semi_cnt), lp->dma_buff, + length - semi_cnt); + } else { + memcpy(skb_put(skb,length), bp, length); + } + bp += (length + 3) & ~3; + if (bp >= lp->end_dma_buff) bp -= lp->dmasize*1024; + lp->rx_dma_ptr = bp; + + if (net_debug > 3) { + printk( "%s: received %d byte DMA packet of type %x\n", + dev->name, length, + (skb->data[ETH_ALEN+ETH_ALEN] << 8) | skb->data[ETH_ALEN+ETH_ALEN+1]); + } + skb->protocol=eth_type_trans(skb,dev); + netif_rx(skb); + dev->stats.rx_packets++; + dev->stats.rx_bytes += length; +} + +#endif /* ALLOW_DMA */ + +static void __init reset_chip(struct net_device *dev) +{ +#if !defined(CONFIG_MACH_MX31ADS) +#if !defined(CS89x0_NONISA_IRQ) + struct net_local *lp = netdev_priv(dev); + int ioaddr = dev->base_addr; +#endif /* CS89x0_NONISA_IRQ */ + int reset_start_time; + + writereg(dev, PP_SelfCTL, readreg(dev, PP_SelfCTL) | POWER_ON_RESET); + + /* wait 30 ms */ + msleep(30); + +#if !defined(CS89x0_NONISA_IRQ) + if (lp->chip_type != CS8900) { + /* Hardware problem requires PNP registers to be reconfigured after a reset */ + writeword(ioaddr, ADD_PORT, PP_CS8920_ISAINT); + outb(dev->irq, ioaddr + DATA_PORT); + outb(0, ioaddr + DATA_PORT + 1); + + writeword(ioaddr, ADD_PORT, PP_CS8920_ISAMemB); + outb((dev->mem_start >> 16) & 0xff, ioaddr + DATA_PORT); + outb((dev->mem_start >> 8) & 0xff, ioaddr + DATA_PORT + 1); + } +#endif /* CS89x0_NONISA_IRQ */ + + /* Wait until the chip is reset */ + reset_start_time = jiffies; + while( (readreg(dev, PP_SelfST) & INIT_DONE) == 0 && jiffies - reset_start_time < 2) + ; +#endif /* !CONFIG_MACH_MX31ADS */ +} + + +static void +control_dc_dc(struct net_device *dev, int on_not_off) +{ + struct net_local *lp = netdev_priv(dev); + unsigned int selfcontrol; + int timenow = jiffies; + /* control the DC to DC convertor in the SelfControl register. + Note: This is hooked up to a general purpose pin, might not + always be a DC to DC convertor. */ + + selfcontrol = HCB1_ENBL; /* Enable the HCB1 bit as an output */ + if (((lp->adapter_cnf & A_CNF_DC_DC_POLARITY) != 0) ^ on_not_off) + selfcontrol |= HCB1; + else + selfcontrol &= ~HCB1; + writereg(dev, PP_SelfCTL, selfcontrol); + + /* Wait for the DC/DC converter to power up - 500ms */ + while (jiffies - timenow < HZ) + ; +} + +#define DETECTED_NONE 0 +#define DETECTED_RJ45H 1 +#define DETECTED_RJ45F 2 +#define DETECTED_AUI 3 +#define DETECTED_BNC 4 + +static int +detect_tp(struct net_device *dev) +{ + struct net_local *lp = netdev_priv(dev); + int timenow = jiffies; + int fdx; + + if (net_debug > 1) printk("%s: Attempting TP\n", dev->name); + + /* If connected to another full duplex capable 10-Base-T card the link pulses + seem to be lost when the auto detect bit in the LineCTL is set. + To overcome this the auto detect bit will be cleared whilst testing the + 10-Base-T interface. This would not be necessary for the sparrow chip but + is simpler to do it anyway. */ + writereg(dev, PP_LineCTL, lp->linectl &~ AUI_ONLY); + control_dc_dc(dev, 0); + + /* Delay for the hardware to work out if the TP cable is present - 150ms */ + for (timenow = jiffies; jiffies - timenow < 15; ) + ; + if ((readreg(dev, PP_LineST) & LINK_OK) == 0) + return DETECTED_NONE; + + if (lp->chip_type == CS8900) { + switch (lp->force & 0xf0) { +#if 0 + case FORCE_AUTO: + printk("%s: cs8900 doesn't autonegotiate\n",dev->name); + return DETECTED_NONE; +#endif + /* CS8900 doesn't support AUTO, change to HALF*/ + case FORCE_AUTO: + lp->force &= ~FORCE_AUTO; + lp->force |= FORCE_HALF; + break; + case FORCE_HALF: + break; + case FORCE_FULL: + writereg(dev, PP_TestCTL, readreg(dev, PP_TestCTL) | FDX_8900); + break; + } + fdx = readreg(dev, PP_TestCTL) & FDX_8900; + } else { + switch (lp->force & 0xf0) { + case FORCE_AUTO: + lp->auto_neg_cnf = AUTO_NEG_ENABLE; + break; + case FORCE_HALF: + lp->auto_neg_cnf = 0; + break; + case FORCE_FULL: + lp->auto_neg_cnf = RE_NEG_NOW | ALLOW_FDX; + break; + } + + writereg(dev, PP_AutoNegCTL, lp->auto_neg_cnf & AUTO_NEG_MASK); + + if ((lp->auto_neg_cnf & AUTO_NEG_BITS) == AUTO_NEG_ENABLE) { + printk(KERN_INFO "%s: negotiating duplex...\n",dev->name); + while (readreg(dev, PP_AutoNegST) & AUTO_NEG_BUSY) { + if (jiffies - timenow > 4000) { + printk(KERN_ERR "**** Full / half duplex auto-negotiation timed out ****\n"); + break; + } + } + } + fdx = readreg(dev, PP_AutoNegST) & FDX_ACTIVE; + } + if (fdx) + return DETECTED_RJ45F; + else + return DETECTED_RJ45H; +} + +/* send a test packet - return true if carrier bits are ok */ +static int +send_test_pkt(struct net_device *dev) +{ + char test_packet[] = { 0,0,0,0,0,0, 0,0,0,0,0,0, + 0, 46, /* A 46 in network order */ + 0, 0, /* DSAP=0 & SSAP=0 fields */ + 0xf3, 0 /* Control (Test Req + P bit set) */ }; + long timenow = jiffies; + + writereg(dev, PP_LineCTL, readreg(dev, PP_LineCTL) | SERIAL_TX_ON); + + memcpy(test_packet, dev->dev_addr, ETH_ALEN); + memcpy(test_packet+ETH_ALEN, dev->dev_addr, ETH_ALEN); + + writeword(dev->base_addr, TX_CMD_PORT, TX_AFTER_ALL); + writeword(dev->base_addr, TX_LEN_PORT, ETH_ZLEN); + + /* Test to see if the chip has allocated memory for the packet */ + while (jiffies - timenow < 5) + if (readreg(dev, PP_BusST) & READY_FOR_TX_NOW) + break; + if (jiffies - timenow >= 5) + return 0; /* this shouldn't happen */ + + /* Write the contents of the packet */ + writewords(dev->base_addr, TX_FRAME_PORT,test_packet,(ETH_ZLEN+1) >>1); + + if (net_debug > 1) printk("Sending test packet "); + /* wait a couple of jiffies for packet to be received */ + for (timenow = jiffies; jiffies - timenow < 3; ) + ; + if ((readreg(dev, PP_TxEvent) & TX_SEND_OK_BITS) == TX_OK) { + if (net_debug > 1) printk("succeeded\n"); + return 1; + } + if (net_debug > 1) printk("failed\n"); + return 0; +} + + +static int +detect_aui(struct net_device *dev) +{ + struct net_local *lp = netdev_priv(dev); + + if (net_debug > 1) printk("%s: Attempting AUI\n", dev->name); + control_dc_dc(dev, 0); + + writereg(dev, PP_LineCTL, (lp->linectl &~ AUTO_AUI_10BASET) | AUI_ONLY); + + if (send_test_pkt(dev)) + return DETECTED_AUI; + else + return DETECTED_NONE; +} + +static int +detect_bnc(struct net_device *dev) +{ + struct net_local *lp = netdev_priv(dev); + + if (net_debug > 1) printk("%s: Attempting BNC\n", dev->name); + control_dc_dc(dev, 1); + + writereg(dev, PP_LineCTL, (lp->linectl &~ AUTO_AUI_10BASET) | AUI_ONLY); + + if (send_test_pkt(dev)) + return DETECTED_BNC; + else + return DETECTED_NONE; +} + + +static void +write_irq(struct net_device *dev, int chip_type, int irq) +{ + int i; + + if (chip_type == CS8900) { + /* Search the mapping table for the corresponding IRQ pin. */ + for (i = 0; i != ARRAY_SIZE(cs8900_irq_map); i++) + if (cs8900_irq_map[i] == irq) + break; + /* Not found */ + if (i == ARRAY_SIZE(cs8900_irq_map)) + i = 3; + writereg(dev, PP_CS8900_ISAINT, i); + } else { + writereg(dev, PP_CS8920_ISAINT, irq); + } +} + +/* Open/initialize the board. This is called (in the current kernel) + sometime after booting when the 'ifconfig' program is run. + + This routine should set everything up anew at each open, even + registers that "should" only need to be set once at boot, so that + there is non-reboot way to recover if something goes wrong. + */ + +/* AKPM: do we need to do any locking here? */ + +static int +net_open(struct net_device *dev) +{ + struct net_local *lp = netdev_priv(dev); + int result = 0; + int i; + int ret; + + if (dev->irq < 2) { + /* Allow interrupts to be generated by the chip */ +/* Cirrus' release had this: */ +#if 0 + writereg(dev, PP_BusCTL, readreg(dev, PP_BusCTL)|ENABLE_IRQ ); +#endif +/* And 2.3.47 had this: */ + writereg(dev, PP_BusCTL, ENABLE_IRQ | MEMORY_ON); + + for (i = 2; i < CS8920_NO_INTS; i++) { + if ((1 << i) & lp->irq_map) { + if (request_irq(i, net_interrupt, 0, dev->name, dev) == 0) { + dev->irq = i; + write_irq(dev, lp->chip_type, i); + /* writereg(dev, PP_BufCFG, GENERATE_SW_INTERRUPT); */ + break; + } + } + } + + if (i >= CS8920_NO_INTS) { + writereg(dev, PP_BusCTL, 0); /* disable interrupts. */ + printk(KERN_ERR "cs89x0: can't get an interrupt\n"); + ret = -EAGAIN; + goto bad_out; + } + } + else + { +#ifndef CONFIG_CS89x0_NONISA_IRQ + if (((1 << dev->irq) & lp->irq_map) == 0) { + printk(KERN_ERR "%s: IRQ %d is not in our map of allowable IRQs, which is %x\n", + dev->name, dev->irq, lp->irq_map); + ret = -EAGAIN; + goto bad_out; + } +#endif +/* FIXME: Cirrus' release had this: */ + writereg(dev, PP_BusCTL, readreg(dev, PP_BusCTL)|ENABLE_IRQ ); +/* And 2.3.47 had this: */ +#if 0 + writereg(dev, PP_BusCTL, ENABLE_IRQ | MEMORY_ON); +#endif + write_irq(dev, lp->chip_type, dev->irq); + ret = request_irq(dev->irq, net_interrupt, 0, dev->name, dev); + if (ret) { + printk(KERN_ERR "cs89x0: request_irq(%d) failed\n", dev->irq); + goto bad_out; + } + } + +#if ALLOW_DMA + if (lp->use_dma) { + if (lp->isa_config & ANY_ISA_DMA) { + unsigned long flags; + lp->dma_buff = (unsigned char *)__get_dma_pages(GFP_KERNEL, + get_order(lp->dmasize * 1024)); + + if (!lp->dma_buff) { + printk(KERN_ERR "%s: cannot get %dK memory for DMA\n", dev->name, lp->dmasize); + goto release_irq; + } + if (net_debug > 1) { + printk( "%s: dma %lx %lx\n", + dev->name, + (unsigned long)lp->dma_buff, + (unsigned long)isa_virt_to_bus(lp->dma_buff)); + } + if ((unsigned long) lp->dma_buff >= MAX_DMA_ADDRESS || + !dma_page_eq(lp->dma_buff, lp->dma_buff+lp->dmasize*1024-1)) { + printk(KERN_ERR "%s: not usable as DMA buffer\n", dev->name); + goto release_irq; + } + memset(lp->dma_buff, 0, lp->dmasize * 1024); /* Why? */ + if (request_dma(dev->dma, dev->name)) { + printk(KERN_ERR "%s: cannot get dma channel %d\n", dev->name, dev->dma); + goto release_irq; + } + write_dma(dev, lp->chip_type, dev->dma); + lp->rx_dma_ptr = lp->dma_buff; + lp->end_dma_buff = lp->dma_buff + lp->dmasize*1024; + spin_lock_irqsave(&lp->lock, flags); + disable_dma(dev->dma); + clear_dma_ff(dev->dma); + set_dma_mode(dev->dma, DMA_RX_MODE); /* auto_init as well */ + set_dma_addr(dev->dma, isa_virt_to_bus(lp->dma_buff)); + set_dma_count(dev->dma, lp->dmasize*1024); + enable_dma(dev->dma); + spin_unlock_irqrestore(&lp->lock, flags); + } + } +#endif /* ALLOW_DMA */ + + /* set the Ethernet address */ + for (i=0; i < ETH_ALEN/2; i++) + writereg(dev, PP_IA+i*2, dev->dev_addr[i*2] | (dev->dev_addr[i*2+1] << 8)); + + /* while we're testing the interface, leave interrupts disabled */ + writereg(dev, PP_BusCTL, MEMORY_ON); + + /* Set the LineCTL quintuplet based on adapter configuration read from EEPROM */ + if ((lp->adapter_cnf & A_CNF_EXTND_10B_2) && (lp->adapter_cnf & A_CNF_LOW_RX_SQUELCH)) + lp->linectl = LOW_RX_SQUELCH; + else + lp->linectl = 0; + + /* check to make sure that they have the "right" hardware available */ + switch(lp->adapter_cnf & A_CNF_MEDIA_TYPE) { + case A_CNF_MEDIA_10B_T: result = lp->adapter_cnf & A_CNF_10B_T; break; + case A_CNF_MEDIA_AUI: result = lp->adapter_cnf & A_CNF_AUI; break; + case A_CNF_MEDIA_10B_2: result = lp->adapter_cnf & A_CNF_10B_2; break; + default: result = lp->adapter_cnf & (A_CNF_10B_T | A_CNF_AUI | A_CNF_10B_2); + } + if (!result) { + printk(KERN_ERR "%s: EEPROM is configured for unavailable media\n", dev->name); +release_dma: +#if ALLOW_DMA + free_dma(dev->dma); +release_irq: + release_dma_buff(lp); +#endif + writereg(dev, PP_LineCTL, readreg(dev, PP_LineCTL) & ~(SERIAL_TX_ON | SERIAL_RX_ON)); + free_irq(dev->irq, dev); + ret = -EAGAIN; + goto bad_out; + } + + /* set the hardware to the configured choice */ + switch(lp->adapter_cnf & A_CNF_MEDIA_TYPE) { + case A_CNF_MEDIA_10B_T: + result = detect_tp(dev); + if (result==DETECTED_NONE) { + printk(KERN_WARNING "%s: 10Base-T (RJ-45) has no cable\n", dev->name); + if (lp->auto_neg_cnf & IMM_BIT) /* check "ignore missing media" bit */ + result = DETECTED_RJ45H; /* Yes! I don't care if I see a link pulse */ + } + break; + case A_CNF_MEDIA_AUI: + result = detect_aui(dev); + if (result==DETECTED_NONE) { + printk(KERN_WARNING "%s: 10Base-5 (AUI) has no cable\n", dev->name); + if (lp->auto_neg_cnf & IMM_BIT) /* check "ignore missing media" bit */ + result = DETECTED_AUI; /* Yes! I don't care if I see a carrrier */ + } + break; + case A_CNF_MEDIA_10B_2: + result = detect_bnc(dev); + if (result==DETECTED_NONE) { + printk(KERN_WARNING "%s: 10Base-2 (BNC) has no cable\n", dev->name); + if (lp->auto_neg_cnf & IMM_BIT) /* check "ignore missing media" bit */ + result = DETECTED_BNC; /* Yes! I don't care if I can xmit a packet */ + } + break; + case A_CNF_MEDIA_AUTO: + writereg(dev, PP_LineCTL, lp->linectl | AUTO_AUI_10BASET); + if (lp->adapter_cnf & A_CNF_10B_T) + if ((result = detect_tp(dev)) != DETECTED_NONE) + break; + if (lp->adapter_cnf & A_CNF_AUI) + if ((result = detect_aui(dev)) != DETECTED_NONE) + break; + if (lp->adapter_cnf & A_CNF_10B_2) + if ((result = detect_bnc(dev)) != DETECTED_NONE) + break; + printk(KERN_ERR "%s: no media detected\n", dev->name); + goto release_dma; + } + switch(result) { + case DETECTED_NONE: + printk(KERN_ERR "%s: no network cable attached to configured media\n", dev->name); + goto release_dma; + case DETECTED_RJ45H: + printk(KERN_INFO "%s: using half-duplex 10Base-T (RJ-45)\n", dev->name); + break; + case DETECTED_RJ45F: + printk(KERN_INFO "%s: using full-duplex 10Base-T (RJ-45)\n", dev->name); + break; + case DETECTED_AUI: + printk(KERN_INFO "%s: using 10Base-5 (AUI)\n", dev->name); + break; + case DETECTED_BNC: + printk(KERN_INFO "%s: using 10Base-2 (BNC)\n", dev->name); + break; + } + + /* Turn on both receive and transmit operations */ + writereg(dev, PP_LineCTL, readreg(dev, PP_LineCTL) | SERIAL_RX_ON | SERIAL_TX_ON); + + /* Receive only error free packets addressed to this card */ + lp->rx_mode = 0; + writereg(dev, PP_RxCTL, DEF_RX_ACCEPT); + + lp->curr_rx_cfg = RX_OK_ENBL | RX_CRC_ERROR_ENBL; + + if (lp->isa_config & STREAM_TRANSFER) + lp->curr_rx_cfg |= RX_STREAM_ENBL; +#if ALLOW_DMA + set_dma_cfg(dev); +#endif + writereg(dev, PP_RxCFG, lp->curr_rx_cfg); + + writereg(dev, PP_TxCFG, TX_LOST_CRS_ENBL | TX_SQE_ERROR_ENBL | TX_OK_ENBL | + TX_LATE_COL_ENBL | TX_JBR_ENBL | TX_ANY_COL_ENBL | TX_16_COL_ENBL); + + writereg(dev, PP_BufCFG, READY_FOR_TX_ENBL | RX_MISS_COUNT_OVRFLOW_ENBL | +#if ALLOW_DMA + dma_bufcfg(dev) | +#endif + TX_COL_COUNT_OVRFLOW_ENBL | TX_UNDERRUN_ENBL); + + /* now that we've got our act together, enable everything */ + writereg(dev, PP_BusCTL, ENABLE_IRQ + | (dev->mem_start?MEMORY_ON : 0) /* turn memory on */ +#if ALLOW_DMA + | dma_busctl(dev) +#endif + ); + netif_start_queue(dev); + if (net_debug > 1) + printk("cs89x0: net_open() succeeded\n"); + return 0; +bad_out: + return ret; +} + +static void net_timeout(struct net_device *dev) +{ + /* If we get here, some higher level has decided we are broken. + There should really be a "kick me" function call instead. */ + if (net_debug > 0) printk("%s: transmit timed out, %s?\n", dev->name, + tx_done(dev) ? "IRQ conflict ?" : "network cable problem"); + /* Try to restart the adaptor. */ + netif_wake_queue(dev); +} + +static netdev_tx_t net_send_packet(struct sk_buff *skb,struct net_device *dev) +{ + struct net_local *lp = netdev_priv(dev); + unsigned long flags; + + if (net_debug > 3) { + printk("%s: sent %d byte packet of type %x\n", + dev->name, skb->len, + (skb->data[ETH_ALEN+ETH_ALEN] << 8) | skb->data[ETH_ALEN+ETH_ALEN+1]); + } + + /* keep the upload from being interrupted, since we + ask the chip to start transmitting before the + whole packet has been completely uploaded. */ + + spin_lock_irqsave(&lp->lock, flags); + netif_stop_queue(dev); + + /* initiate a transmit sequence */ + writeword(dev->base_addr, TX_CMD_PORT, lp->send_cmd); + writeword(dev->base_addr, TX_LEN_PORT, skb->len); + + /* Test to see if the chip has allocated memory for the packet */ + if ((readreg(dev, PP_BusST) & READY_FOR_TX_NOW) == 0) { + /* + * Gasp! It hasn't. But that shouldn't happen since + * we're waiting for TxOk, so return 1 and requeue this packet. + */ + + spin_unlock_irqrestore(&lp->lock, flags); + if (net_debug) printk("cs89x0: Tx buffer not free!\n"); + return NETDEV_TX_BUSY; + } + /* Write the contents of the packet */ + writewords(dev->base_addr, TX_FRAME_PORT,skb->data,(skb->len+1) >>1); + spin_unlock_irqrestore(&lp->lock, flags); + dev->stats.tx_bytes += skb->len; + dev_kfree_skb (skb); + + /* + * We DO NOT call netif_wake_queue() here. + * We also DO NOT call netif_start_queue(). + * + * Either of these would cause another bottom half run through + * net_send_packet() before this packet has fully gone out. That causes + * us to hit the "Gasp!" above and the send is rescheduled. it runs like + * a dog. We just return and wait for the Tx completion interrupt handler + * to restart the netdevice layer + */ + + return NETDEV_TX_OK; +} + +/* The typical workload of the driver: + Handle the network interface interrupts. */ + +static irqreturn_t net_interrupt(int irq, void *dev_id) +{ + struct net_device *dev = dev_id; + struct net_local *lp; + int ioaddr, status; + int handled = 0; + + ioaddr = dev->base_addr; + lp = netdev_priv(dev); + + /* we MUST read all the events out of the ISQ, otherwise we'll never + get interrupted again. As a consequence, we can't have any limit + on the number of times we loop in the interrupt handler. The + hardware guarantees that eventually we'll run out of events. Of + course, if you're on a slow machine, and packets are arriving + faster than you can read them off, you're screwed. Hasta la + vista, baby! */ + while ((status = readword(dev->base_addr, ISQ_PORT))) { + if (net_debug > 4)printk("%s: event=%04x\n", dev->name, status); + handled = 1; + switch(status & ISQ_EVENT_MASK) { + case ISQ_RECEIVER_EVENT: + /* Got a packet(s). */ + net_rx(dev); + break; + case ISQ_TRANSMITTER_EVENT: + dev->stats.tx_packets++; + netif_wake_queue(dev); /* Inform upper layers. */ + if ((status & ( TX_OK | + TX_LOST_CRS | + TX_SQE_ERROR | + TX_LATE_COL | + TX_16_COL)) != TX_OK) { + if ((status & TX_OK) == 0) + dev->stats.tx_errors++; + if (status & TX_LOST_CRS) + dev->stats.tx_carrier_errors++; + if (status & TX_SQE_ERROR) + dev->stats.tx_heartbeat_errors++; + if (status & TX_LATE_COL) + dev->stats.tx_window_errors++; + if (status & TX_16_COL) + dev->stats.tx_aborted_errors++; + } + break; + case ISQ_BUFFER_EVENT: + if (status & READY_FOR_TX) { + /* we tried to transmit a packet earlier, + but inexplicably ran out of buffers. + That shouldn't happen since we only ever + load one packet. Shrug. Do the right + thing anyway. */ + netif_wake_queue(dev); /* Inform upper layers. */ + } + if (status & TX_UNDERRUN) { + if (net_debug > 0) printk("%s: transmit underrun\n", dev->name); + lp->send_underrun++; + if (lp->send_underrun == 3) lp->send_cmd = TX_AFTER_381; + else if (lp->send_underrun == 6) lp->send_cmd = TX_AFTER_ALL; + /* transmit cycle is done, although + frame wasn't transmitted - this + avoids having to wait for the upper + layers to timeout on us, in the + event of a tx underrun */ + netif_wake_queue(dev); /* Inform upper layers. */ + } +#if ALLOW_DMA + if (lp->use_dma && (status & RX_DMA)) { + int count = readreg(dev, PP_DmaFrameCnt); + while(count) { + if (net_debug > 5) + printk("%s: receiving %d DMA frames\n", dev->name, count); + if (net_debug > 2 && count >1) + printk("%s: receiving %d DMA frames\n", dev->name, count); + dma_rx(dev); + if (--count == 0) + count = readreg(dev, PP_DmaFrameCnt); + if (net_debug > 2 && count > 0) + printk("%s: continuing with %d DMA frames\n", dev->name, count); + } + } +#endif + break; + case ISQ_RX_MISS_EVENT: + dev->stats.rx_missed_errors += (status >> 6); + break; + case ISQ_TX_COL_EVENT: + dev->stats.collisions += (status >> 6); + break; + } + } + return IRQ_RETVAL(handled); +} + +static void +count_rx_errors(int status, struct net_device *dev) +{ + dev->stats.rx_errors++; + if (status & RX_RUNT) + dev->stats.rx_length_errors++; + if (status & RX_EXTRA_DATA) + dev->stats.rx_length_errors++; + if ((status & RX_CRC_ERROR) && !(status & (RX_EXTRA_DATA|RX_RUNT))) + /* per str 172 */ + dev->stats.rx_crc_errors++; + if (status & RX_DRIBBLE) + dev->stats.rx_frame_errors++; +} + +/* We have a good packet(s), get it/them out of the buffers. */ +static void +net_rx(struct net_device *dev) +{ + struct sk_buff *skb; + int status, length; + + int ioaddr = dev->base_addr; + status = readword(ioaddr, RX_FRAME_PORT); + length = readword(ioaddr, RX_FRAME_PORT); + + if ((status & RX_OK) == 0) { + count_rx_errors(status, dev); + return; + } + + /* Malloc up new buffer. */ + skb = dev_alloc_skb(length + 2); + if (skb == NULL) { +#if 0 /* Again, this seems a cruel thing to do */ + printk(KERN_WARNING "%s: Memory squeeze, dropping packet.\n", dev->name); +#endif + dev->stats.rx_dropped++; + return; + } + skb_reserve(skb, 2); /* longword align L3 header */ + + readwords(ioaddr, RX_FRAME_PORT, skb_put(skb, length), length >> 1); + if (length & 1) + skb->data[length-1] = readword(ioaddr, RX_FRAME_PORT); + + if (net_debug > 3) { + printk( "%s: received %d byte packet of type %x\n", + dev->name, length, + (skb->data[ETH_ALEN+ETH_ALEN] << 8) | skb->data[ETH_ALEN+ETH_ALEN+1]); + } + + skb->protocol=eth_type_trans(skb,dev); + netif_rx(skb); + dev->stats.rx_packets++; + dev->stats.rx_bytes += length; +} + +#if ALLOW_DMA +static void release_dma_buff(struct net_local *lp) +{ + if (lp->dma_buff) { + free_pages((unsigned long)(lp->dma_buff), get_order(lp->dmasize * 1024)); + lp->dma_buff = NULL; + } +} +#endif + +/* The inverse routine to net_open(). */ +static int +net_close(struct net_device *dev) +{ +#if ALLOW_DMA + struct net_local *lp = netdev_priv(dev); +#endif + + netif_stop_queue(dev); + + writereg(dev, PP_RxCFG, 0); + writereg(dev, PP_TxCFG, 0); + writereg(dev, PP_BufCFG, 0); + writereg(dev, PP_BusCTL, 0); + + free_irq(dev->irq, dev); + +#if ALLOW_DMA + if (lp->use_dma && lp->dma) { + free_dma(dev->dma); + release_dma_buff(lp); + } +#endif + + /* Update the statistics here. */ + return 0; +} + +/* Get the current statistics. This may be called with the card open or + closed. */ +static struct net_device_stats * +net_get_stats(struct net_device *dev) +{ + struct net_local *lp = netdev_priv(dev); + unsigned long flags; + + spin_lock_irqsave(&lp->lock, flags); + /* Update the statistics from the device registers. */ + dev->stats.rx_missed_errors += (readreg(dev, PP_RxMiss) >> 6); + dev->stats.collisions += (readreg(dev, PP_TxCol) >> 6); + spin_unlock_irqrestore(&lp->lock, flags); + + return &dev->stats; +} + +static void set_multicast_list(struct net_device *dev) +{ + struct net_local *lp = netdev_priv(dev); + unsigned long flags; + + spin_lock_irqsave(&lp->lock, flags); + if(dev->flags&IFF_PROMISC) + { + lp->rx_mode = RX_ALL_ACCEPT; + } + else if ((dev->flags & IFF_ALLMULTI) || !netdev_mc_empty(dev)) + { + /* The multicast-accept list is initialized to accept-all, and we + rely on higher-level filtering for now. */ + lp->rx_mode = RX_MULTCAST_ACCEPT; + } + else + lp->rx_mode = 0; + + writereg(dev, PP_RxCTL, DEF_RX_ACCEPT | lp->rx_mode); + + /* in promiscuous mode, we accept errored packets, so we have to enable interrupts on them also */ + writereg(dev, PP_RxCFG, lp->curr_rx_cfg | + (lp->rx_mode == RX_ALL_ACCEPT? (RX_CRC_ERROR_ENBL|RX_RUNT_ENBL|RX_EXTRA_DATA_ENBL) : 0)); + spin_unlock_irqrestore(&lp->lock, flags); +} + + +static int set_mac_address(struct net_device *dev, void *p) +{ + int i; + struct sockaddr *addr = p; + + if (netif_running(dev)) + return -EBUSY; + + memcpy(dev->dev_addr, addr->sa_data, dev->addr_len); + + if (net_debug) + printk("%s: Setting MAC address to %pM.\n", + dev->name, dev->dev_addr); + + /* set the Ethernet address */ + for (i=0; i < ETH_ALEN/2; i++) + writereg(dev, PP_IA+i*2, dev->dev_addr[i*2] | (dev->dev_addr[i*2+1] << 8)); + + return 0; +} + +#ifdef MODULE + +static struct net_device *dev_cs89x0; + +/* + * Support the 'debug' module parm even if we're compiled for non-debug to + * avoid breaking someone's startup scripts + */ + +static int io; +static int irq; +static int debug; +static char media[8]; +static int duplex=-1; + +static int use_dma; /* These generate unused var warnings if ALLOW_DMA = 0 */ +static int dma; +static int dmasize=16; /* or 64 */ + +module_param(io, int, 0); +module_param(irq, int, 0); +module_param(debug, int, 0); +module_param_string(media, media, sizeof(media), 0); +module_param(duplex, int, 0); +module_param(dma , int, 0); +module_param(dmasize , int, 0); +module_param(use_dma , int, 0); +MODULE_PARM_DESC(io, "cs89x0 I/O base address"); +MODULE_PARM_DESC(irq, "cs89x0 IRQ number"); +#if DEBUGGING +MODULE_PARM_DESC(debug, "cs89x0 debug level (0-6)"); +#else +MODULE_PARM_DESC(debug, "(ignored)"); +#endif +MODULE_PARM_DESC(media, "Set cs89x0 adapter(s) media type(s) (rj45,bnc,aui)"); +/* No other value than -1 for duplex seems to be currently interpreted */ +MODULE_PARM_DESC(duplex, "(ignored)"); +#if ALLOW_DMA +MODULE_PARM_DESC(dma , "cs89x0 ISA DMA channel; ignored if use_dma=0"); +MODULE_PARM_DESC(dmasize , "cs89x0 DMA size in kB (16,64); ignored if use_dma=0"); +MODULE_PARM_DESC(use_dma , "cs89x0 using DMA (0-1)"); +#else +MODULE_PARM_DESC(dma , "(ignored)"); +MODULE_PARM_DESC(dmasize , "(ignored)"); +MODULE_PARM_DESC(use_dma , "(ignored)"); +#endif + +MODULE_AUTHOR("Mike Cruse, Russwll Nelson <nelson@crynwr.com>, Andrew Morton"); +MODULE_LICENSE("GPL"); + + +/* +* media=t - specify media type + or media=2 + or media=aui + or medai=auto +* duplex=0 - specify forced half/full/autonegotiate duplex +* debug=# - debug level + + +* Default Chip Configuration: + * DMA Burst = enabled + * IOCHRDY Enabled = enabled + * UseSA = enabled + * CS8900 defaults to half-duplex if not specified on command-line + * CS8920 defaults to autoneg if not specified on command-line + * Use reset defaults for other config parameters + +* Assumptions: + * media type specified is supported (circuitry is present) + * if memory address is > 1MB, then required mem decode hw is present + * if 10B-2, then agent other than driver will enable DC/DC converter + (hw or software util) + + +*/ + +int __init init_module(void) +{ + struct net_device *dev = alloc_etherdev(sizeof(struct net_local)); + struct net_local *lp; + int ret = 0; + +#if DEBUGGING + net_debug = debug; +#else + debug = 0; +#endif + if (!dev) + return -ENOMEM; + + dev->irq = irq; + dev->base_addr = io; + lp = netdev_priv(dev); + +#if ALLOW_DMA + if (use_dma) { + lp->use_dma = use_dma; + lp->dma = dma; + lp->dmasize = dmasize; + } +#endif + + spin_lock_init(&lp->lock); + + /* boy, they'd better get these right */ + if (!strcmp(media, "rj45")) + lp->adapter_cnf = A_CNF_MEDIA_10B_T | A_CNF_10B_T; + else if (!strcmp(media, "aui")) + lp->adapter_cnf = A_CNF_MEDIA_AUI | A_CNF_AUI; + else if (!strcmp(media, "bnc")) + lp->adapter_cnf = A_CNF_MEDIA_10B_2 | A_CNF_10B_2; + else + lp->adapter_cnf = A_CNF_MEDIA_10B_T | A_CNF_10B_T; + + if (duplex==-1) + lp->auto_neg_cnf = AUTO_NEG_ENABLE; + + if (io == 0) { + printk(KERN_ERR "cs89x0.c: Module autoprobing not allowed.\n"); + printk(KERN_ERR "cs89x0.c: Append io=0xNNN\n"); + ret = -EPERM; + goto out; + } else if (io <= 0x1ff) { + ret = -ENXIO; + goto out; + } + +#if ALLOW_DMA + if (use_dma && dmasize != 16 && dmasize != 64) { + printk(KERN_ERR "cs89x0.c: dma size must be either 16K or 64K, not %dK\n", dmasize); + ret = -EPERM; + goto out; + } +#endif + ret = cs89x0_probe1(dev, io, 1); + if (ret) + goto out; + + dev_cs89x0 = dev; + return 0; +out: + free_netdev(dev); + return ret; +} + +void __exit +cleanup_module(void) +{ + unregister_netdev(dev_cs89x0); + writeword(dev_cs89x0->base_addr, ADD_PORT, PP_ChipID); + release_region(dev_cs89x0->base_addr, NETCARD_IO_EXTENT); + free_netdev(dev_cs89x0); +} +#endif /* MODULE */ + +/* + * Local variables: + * version-control: t + * kept-new-versions: 5 + * c-indent-level: 8 + * tab-width: 8 + * End: + * + */ diff --git a/drivers/net/ethernet/cirrus/cs89x0.h b/drivers/net/ethernet/cirrus/cs89x0.h new file mode 100644 index 0000000..91423b7 --- /dev/null +++ b/drivers/net/ethernet/cirrus/cs89x0.h @@ -0,0 +1,465 @@ +/* Copyright, 1988-1992, Russell Nelson, Crynwr Software + + This program is free software; you can redistribute it and/or modify + it under the terms of the GNU General Public License as published by + the Free Software Foundation, version 1. + + This program is distributed in the hope that it will be useful, + but WITHOUT ANY WARRANTY; without even the implied warranty of + MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + GNU General Public License for more details. + + You should have received a copy of the GNU General Public License + along with this program; if not, write to the Free Software + Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + */ + + +#define PP_ChipID 0x0000 /* offset 0h -> Corp -ID */ + /* offset 2h -> Model/Product Number */ + /* offset 3h -> Chip Revision Number */ + +#define PP_ISAIOB 0x0020 /* IO base address */ +#define PP_CS8900_ISAINT 0x0022 /* ISA interrupt select */ +#define PP_CS8920_ISAINT 0x0370 /* ISA interrupt select */ +#define PP_CS8900_ISADMA 0x0024 /* ISA Rec DMA channel */ +#define PP_CS8920_ISADMA 0x0374 /* ISA Rec DMA channel */ +#define PP_ISASOF 0x0026 /* ISA DMA offset */ +#define PP_DmaFrameCnt 0x0028 /* ISA DMA Frame count */ +#define PP_DmaByteCnt 0x002A /* ISA DMA Byte count */ +#define PP_CS8900_ISAMemB 0x002C /* Memory base */ +#define PP_CS8920_ISAMemB 0x0348 /* */ + +#define PP_ISABootBase 0x0030 /* Boot Prom base */ +#define PP_ISABootMask 0x0034 /* Boot Prom Mask */ + +/* EEPROM data and command registers */ +#define PP_EECMD 0x0040 /* NVR Interface Command register */ +#define PP_EEData 0x0042 /* NVR Interface Data Register */ +#define PP_DebugReg 0x0044 /* Debug Register */ + +#define PP_RxCFG 0x0102 /* Rx Bus config */ +#define PP_RxCTL 0x0104 /* Receive Control Register */ +#define PP_TxCFG 0x0106 /* Transmit Config Register */ +#define PP_TxCMD 0x0108 /* Transmit Command Register */ +#define PP_BufCFG 0x010A /* Bus configuration Register */ +#define PP_LineCTL 0x0112 /* Line Config Register */ +#define PP_SelfCTL 0x0114 /* Self Command Register */ +#define PP_BusCTL 0x0116 /* ISA bus control Register */ +#define PP_TestCTL 0x0118 /* Test Register */ +#define PP_AutoNegCTL 0x011C /* Auto Negotiation Ctrl */ + +#define PP_ISQ 0x0120 /* Interrupt Status */ +#define PP_RxEvent 0x0124 /* Rx Event Register */ +#define PP_TxEvent 0x0128 /* Tx Event Register */ +#define PP_BufEvent 0x012C /* Bus Event Register */ +#define PP_RxMiss 0x0130 /* Receive Miss Count */ +#define PP_TxCol 0x0132 /* Transmit Collision Count */ +#define PP_LineST 0x0134 /* Line State Register */ +#define PP_SelfST 0x0136 /* Self State register */ +#define PP_BusST 0x0138 /* Bus Status */ +#define PP_TDR 0x013C /* Time Domain Reflectometry */ +#define PP_AutoNegST 0x013E /* Auto Neg Status */ +#define PP_TxCommand 0x0144 /* Tx Command */ +#define PP_TxLength 0x0146 /* Tx Length */ +#define PP_LAF 0x0150 /* Hash Table */ +#define PP_IA 0x0158 /* Physical Address Register */ + +#define PP_RxStatus 0x0400 /* Receive start of frame */ +#define PP_RxLength 0x0402 /* Receive Length of frame */ +#define PP_RxFrame 0x0404 /* Receive frame pointer */ +#define PP_TxFrame 0x0A00 /* Transmit frame pointer */ + +/* Primary I/O Base Address. If no I/O base is supplied by the user, then this */ +/* can be used as the default I/O base to access the PacketPage Area. */ +#define DEFAULTIOBASE 0x0300 +#define FIRST_IO 0x020C /* First I/O port to check */ +#define LAST_IO 0x037C /* Last I/O port to check (+10h) */ +#define ADD_MASK 0x3000 /* Mask it use of the ADD_PORT register */ +#define ADD_SIG 0x3000 /* Expected ID signature */ + +/* On Macs, we only need use the ISA I/O stuff until we do MEMORY_ON */ +#ifdef CONFIG_MAC +#define LCSLOTBASE 0xfee00000 +#define MMIOBASE 0x40000 +#endif + +#define CHIP_EISA_ID_SIG 0x630E /* Product ID Code for Crystal Chip (CS8900 spec 4.3) */ +#define CHIP_EISA_ID_SIG_STR "0x630E" + +#ifdef IBMEIPKT +#define EISA_ID_SIG 0x4D24 /* IBM */ +#define PART_NO_SIG 0x1010 /* IBM */ +#define MONGOOSE_BIT 0x0000 /* IBM */ +#else +#define EISA_ID_SIG 0x630E /* PnP Vendor ID (same as chip id for Crystal board) */ +#define PART_NO_SIG 0x4000 /* ID code CS8920 board (PnP Vendor Product code) */ +#define MONGOOSE_BIT 0x2000 /* PART_NO_SIG + MONGOOSE_BUT => ID of mongoose */ +#endif + +#define PRODUCT_ID_ADD 0x0002 /* Address of product ID */ + +/* Mask to find out the types of registers */ +#define REG_TYPE_MASK 0x001F + +/* Eeprom Commands */ +#define ERSE_WR_ENBL 0x00F0 +#define ERSE_WR_DISABLE 0x0000 + +/* Defines Control/Config register quintuplet numbers */ +#define RX_BUF_CFG 0x0003 +#define RX_CONTROL 0x0005 +#define TX_CFG 0x0007 +#define TX_COMMAND 0x0009 +#define BUF_CFG 0x000B +#define LINE_CONTROL 0x0013 +#define SELF_CONTROL 0x0015 +#define BUS_CONTROL 0x0017 +#define TEST_CONTROL 0x0019 + +/* Defines Status/Count registers quintuplet numbers */ +#define RX_EVENT 0x0004 +#define TX_EVENT 0x0008 +#define BUF_EVENT 0x000C +#define RX_MISS_COUNT 0x0010 +#define TX_COL_COUNT 0x0012 +#define LINE_STATUS 0x0014 +#define SELF_STATUS 0x0016 +#define BUS_STATUS 0x0018 +#define TDR 0x001C + +/* PP_RxCFG - Receive Configuration and Interrupt Mask bit definition - Read/write */ +#define SKIP_1 0x0040 +#define RX_STREAM_ENBL 0x0080 +#define RX_OK_ENBL 0x0100 +#define RX_DMA_ONLY 0x0200 +#define AUTO_RX_DMA 0x0400 +#define BUFFER_CRC 0x0800 +#define RX_CRC_ERROR_ENBL 0x1000 +#define RX_RUNT_ENBL 0x2000 +#define RX_EXTRA_DATA_ENBL 0x4000 + +/* PP_RxCTL - Receive Control bit definition - Read/write */ +#define RX_IA_HASH_ACCEPT 0x0040 +#define RX_PROM_ACCEPT 0x0080 +#define RX_OK_ACCEPT 0x0100 +#define RX_MULTCAST_ACCEPT 0x0200 +#define RX_IA_ACCEPT 0x0400 +#define RX_BROADCAST_ACCEPT 0x0800 +#define RX_BAD_CRC_ACCEPT 0x1000 +#define RX_RUNT_ACCEPT 0x2000 +#define RX_EXTRA_DATA_ACCEPT 0x4000 +#define RX_ALL_ACCEPT (RX_PROM_ACCEPT|RX_BAD_CRC_ACCEPT|RX_RUNT_ACCEPT|RX_EXTRA_DATA_ACCEPT) +/* Default receive mode - individually addressed, broadcast, and error free */ +#define DEF_RX_ACCEPT (RX_IA_ACCEPT | RX_BROADCAST_ACCEPT | RX_OK_ACCEPT) + +/* PP_TxCFG - Transmit Configuration Interrupt Mask bit definition - Read/write */ +#define TX_LOST_CRS_ENBL 0x0040 +#define TX_SQE_ERROR_ENBL 0x0080 +#define TX_OK_ENBL 0x0100 +#define TX_LATE_COL_ENBL 0x0200 +#define TX_JBR_ENBL 0x0400 +#define TX_ANY_COL_ENBL 0x0800 +#define TX_16_COL_ENBL 0x8000 + +/* PP_TxCMD - Transmit Command bit definition - Read-only */ +#define TX_START_4_BYTES 0x0000 +#define TX_START_64_BYTES 0x0040 +#define TX_START_128_BYTES 0x0080 +#define TX_START_ALL_BYTES 0x00C0 +#define TX_FORCE 0x0100 +#define TX_ONE_COL 0x0200 +#define TX_TWO_PART_DEFF_DISABLE 0x0400 +#define TX_NO_CRC 0x1000 +#define TX_RUNT 0x2000 + +/* PP_BufCFG - Buffer Configuration Interrupt Mask bit definition - Read/write */ +#define GENERATE_SW_INTERRUPT 0x0040 +#define RX_DMA_ENBL 0x0080 +#define READY_FOR_TX_ENBL 0x0100 +#define TX_UNDERRUN_ENBL 0x0200 +#define RX_MISS_ENBL 0x0400 +#define RX_128_BYTE_ENBL 0x0800 +#define TX_COL_COUNT_OVRFLOW_ENBL 0x1000 +#define RX_MISS_COUNT_OVRFLOW_ENBL 0x2000 +#define RX_DEST_MATCH_ENBL 0x8000 + +/* PP_LineCTL - Line Control bit definition - Read/write */ +#define SERIAL_RX_ON 0x0040 +#define SERIAL_TX_ON 0x0080 +#define AUI_ONLY 0x0100 +#define AUTO_AUI_10BASET 0x0200 +#define MODIFIED_BACKOFF 0x0800 +#define NO_AUTO_POLARITY 0x1000 +#define TWO_PART_DEFDIS 0x2000 +#define LOW_RX_SQUELCH 0x4000 + +/* PP_SelfCTL - Software Self Control bit definition - Read/write */ +#define POWER_ON_RESET 0x0040 +#define SW_STOP 0x0100 +#define SLEEP_ON 0x0200 +#define AUTO_WAKEUP 0x0400 +#define HCB0_ENBL 0x1000 +#define HCB1_ENBL 0x2000 +#define HCB0 0x4000 +#define HCB1 0x8000 + +/* PP_BusCTL - ISA Bus Control bit definition - Read/write */ +#define RESET_RX_DMA 0x0040 +#define MEMORY_ON 0x0400 +#define DMA_BURST_MODE 0x0800 +#define IO_CHANNEL_READY_ON 0x1000 +#define RX_DMA_SIZE_64K 0x2000 +#define ENABLE_IRQ 0x8000 + +/* PP_TestCTL - Test Control bit definition - Read/write */ +#define LINK_OFF 0x0080 +#define ENDEC_LOOPBACK 0x0200 +#define AUI_LOOPBACK 0x0400 +#define BACKOFF_OFF 0x0800 +#define FDX_8900 0x4000 +#define FAST_TEST 0x8000 + +/* PP_RxEvent - Receive Event Bit definition - Read-only */ +#define RX_IA_HASHED 0x0040 +#define RX_DRIBBLE 0x0080 +#define RX_OK 0x0100 +#define RX_HASHED 0x0200 +#define RX_IA 0x0400 +#define RX_BROADCAST 0x0800 +#define RX_CRC_ERROR 0x1000 +#define RX_RUNT 0x2000 +#define RX_EXTRA_DATA 0x4000 + +#define HASH_INDEX_MASK 0x0FC00 + +/* PP_TxEvent - Transmit Event Bit definition - Read-only */ +#define TX_LOST_CRS 0x0040 +#define TX_SQE_ERROR 0x0080 +#define TX_OK 0x0100 +#define TX_LATE_COL 0x0200 +#define TX_JBR 0x0400 +#define TX_16_COL 0x8000 +#define TX_SEND_OK_BITS (TX_OK|TX_LOST_CRS) +#define TX_COL_COUNT_MASK 0x7800 + +/* PP_BufEvent - Buffer Event Bit definition - Read-only */ +#define SW_INTERRUPT 0x0040 +#define RX_DMA 0x0080 +#define READY_FOR_TX 0x0100 +#define TX_UNDERRUN 0x0200 +#define RX_MISS 0x0400 +#define RX_128_BYTE 0x0800 +#define TX_COL_OVRFLW 0x1000 +#define RX_MISS_OVRFLW 0x2000 +#define RX_DEST_MATCH 0x8000 + +/* PP_LineST - Ethernet Line Status bit definition - Read-only */ +#define LINK_OK 0x0080 +#define AUI_ON 0x0100 +#define TENBASET_ON 0x0200 +#define POLARITY_OK 0x1000 +#define CRS_OK 0x4000 + +/* PP_SelfST - Chip Software Status bit definition */ +#define ACTIVE_33V 0x0040 +#define INIT_DONE 0x0080 +#define SI_BUSY 0x0100 +#define EEPROM_PRESENT 0x0200 +#define EEPROM_OK 0x0400 +#define EL_PRESENT 0x0800 +#define EE_SIZE_64 0x1000 + +/* PP_BusST - ISA Bus Status bit definition */ +#define TX_BID_ERROR 0x0080 +#define READY_FOR_TX_NOW 0x0100 + +/* PP_AutoNegCTL - Auto Negotiation Control bit definition */ +#define RE_NEG_NOW 0x0040 +#define ALLOW_FDX 0x0080 +#define AUTO_NEG_ENABLE 0x0100 +#define NLP_ENABLE 0x0200 +#define FORCE_FDX 0x8000 +#define AUTO_NEG_BITS (FORCE_FDX|NLP_ENABLE|AUTO_NEG_ENABLE) +#define AUTO_NEG_MASK (FORCE_FDX|NLP_ENABLE|AUTO_NEG_ENABLE|ALLOW_FDX|RE_NEG_NOW) + +/* PP_AutoNegST - Auto Negotiation Status bit definition */ +#define AUTO_NEG_BUSY 0x0080 +#define FLP_LINK 0x0100 +#define FLP_LINK_GOOD 0x0800 +#define LINK_FAULT 0x1000 +#define HDX_ACTIVE 0x4000 +#define FDX_ACTIVE 0x8000 + +/* The following block defines the ISQ event types */ +#define ISQ_RECEIVER_EVENT 0x04 +#define ISQ_TRANSMITTER_EVENT 0x08 +#define ISQ_BUFFER_EVENT 0x0c +#define ISQ_RX_MISS_EVENT 0x10 +#define ISQ_TX_COL_EVENT 0x12 + +#define ISQ_EVENT_MASK 0x003F /* ISQ mask to find out type of event */ +#define ISQ_HIST 16 /* small history buffer */ +#define AUTOINCREMENT 0x8000 /* Bit mask to set bit-15 for autoincrement */ + +#define TXRXBUFSIZE 0x0600 +#define RXDMABUFSIZE 0x8000 +#define RXDMASIZE 0x4000 +#define TXRX_LENGTH_MASK 0x07FF + +/* rx options bits */ +#define RCV_WITH_RXON 1 /* Set SerRx ON */ +#define RCV_COUNTS 2 /* Use Framecnt1 */ +#define RCV_PONG 4 /* Pong respondent */ +#define RCV_DONG 8 /* Dong operation */ +#define RCV_POLLING 0x10 /* Poll RxEvent */ +#define RCV_ISQ 0x20 /* Use ISQ, int */ +#define RCV_AUTO_DMA 0x100 /* Set AutoRxDMAE */ +#define RCV_DMA 0x200 /* Set RxDMA only */ +#define RCV_DMA_ALL 0x400 /* Copy all DMA'ed */ +#define RCV_FIXED_DATA 0x800 /* Every frame same */ +#define RCV_IO 0x1000 /* Use ISA IO only */ +#define RCV_MEMORY 0x2000 /* Use ISA Memory */ + +#define RAM_SIZE 0x1000 /* The card has 4k bytes or RAM */ +#define PKT_START PP_TxFrame /* Start of packet RAM */ + +#define RX_FRAME_PORT 0x0000 +#define TX_FRAME_PORT RX_FRAME_PORT +#define TX_CMD_PORT 0x0004 +#define TX_NOW 0x0000 /* Tx packet after 5 bytes copied */ +#define TX_AFTER_381 0x0040 /* Tx packet after 381 bytes copied */ +#define TX_AFTER_ALL 0x00c0 /* Tx packet after all bytes copied */ +#define TX_LEN_PORT 0x0006 +#define ISQ_PORT 0x0008 +#define ADD_PORT 0x000A +#define DATA_PORT 0x000C + +#define EEPROM_WRITE_EN 0x00F0 +#define EEPROM_WRITE_DIS 0x0000 +#define EEPROM_WRITE_CMD 0x0100 +#define EEPROM_READ_CMD 0x0200 + +/* Receive Header */ +/* Description of header of each packet in receive area of memory */ +#define RBUF_EVENT_LOW 0 /* Low byte of RxEvent - status of received frame */ +#define RBUF_EVENT_HIGH 1 /* High byte of RxEvent - status of received frame */ +#define RBUF_LEN_LOW 2 /* Length of received data - low byte */ +#define RBUF_LEN_HI 3 /* Length of received data - high byte */ +#define RBUF_HEAD_LEN 4 /* Length of this header */ + +#define CHIP_READ 0x1 /* Used to mark state of the repins code (chip or dma) */ +#define DMA_READ 0x2 /* Used to mark state of the repins code (chip or dma) */ + +/* for bios scan */ +/* */ +#ifdef CSDEBUG +/* use these values for debugging bios scan */ +#define BIOS_START_SEG 0x00000 +#define BIOS_OFFSET_INC 0x0010 +#else +#define BIOS_START_SEG 0x0c000 +#define BIOS_OFFSET_INC 0x0200 +#endif + +#define BIOS_LAST_OFFSET 0x0fc00 + +/* Byte offsets into the EEPROM configuration buffer */ +#define ISA_CNF_OFFSET 0x6 +#define TX_CTL_OFFSET (ISA_CNF_OFFSET + 8) /* 8900 eeprom */ +#define AUTO_NEG_CNF_OFFSET (ISA_CNF_OFFSET + 8) /* 8920 eeprom */ + + /* the assumption here is that the bits in the eeprom are generally */ + /* in the same position as those in the autonegctl register. */ + /* Of course the IMM bit is not in that register so it must be */ + /* masked out */ +#define EE_FORCE_FDX 0x8000 +#define EE_NLP_ENABLE 0x0200 +#define EE_AUTO_NEG_ENABLE 0x0100 +#define EE_ALLOW_FDX 0x0080 +#define EE_AUTO_NEG_CNF_MASK (EE_FORCE_FDX|EE_NLP_ENABLE|EE_AUTO_NEG_ENABLE|EE_ALLOW_FDX) + +#define IMM_BIT 0x0040 /* ignore missing media */ + +#define ADAPTER_CNF_OFFSET (AUTO_NEG_CNF_OFFSET + 2) +#define A_CNF_10B_T 0x0001 +#define A_CNF_AUI 0x0002 +#define A_CNF_10B_2 0x0004 +#define A_CNF_MEDIA_TYPE 0x0070 +#define A_CNF_MEDIA_AUTO 0x0070 +#define A_CNF_MEDIA_10B_T 0x0020 +#define A_CNF_MEDIA_AUI 0x0040 +#define A_CNF_MEDIA_10B_2 0x0010 +#define A_CNF_DC_DC_POLARITY 0x0080 +#define A_CNF_NO_AUTO_POLARITY 0x2000 +#define A_CNF_LOW_RX_SQUELCH 0x4000 +#define A_CNF_EXTND_10B_2 0x8000 + +#define PACKET_PAGE_OFFSET 0x8 + +/* Bit definitions for the ISA configuration word from the EEPROM */ +#define INT_NO_MASK 0x000F +#define DMA_NO_MASK 0x0070 +#define ISA_DMA_SIZE 0x0200 +#define ISA_AUTO_RxDMA 0x0400 +#define ISA_RxDMA 0x0800 +#define DMA_BURST 0x1000 +#define STREAM_TRANSFER 0x2000 +#define ANY_ISA_DMA (ISA_AUTO_RxDMA | ISA_RxDMA) + +/* DMA controller registers */ +#define DMA_BASE 0x00 /* DMA controller base */ +#define DMA_BASE_2 0x0C0 /* DMA controller base */ + +#define DMA_STAT 0x0D0 /* DMA controller status register */ +#define DMA_MASK 0x0D4 /* DMA controller mask register */ +#define DMA_MODE 0x0D6 /* DMA controller mode register */ +#define DMA_RESETFF 0x0D8 /* DMA controller first/last flip flop */ + +/* DMA data */ +#define DMA_DISABLE 0x04 /* Disable channel n */ +#define DMA_ENABLE 0x00 /* Enable channel n */ +/* Demand transfers, incr. address, auto init, writes, ch. n */ +#define DMA_RX_MODE 0x14 +/* Demand transfers, incr. address, auto init, reads, ch. n */ +#define DMA_TX_MODE 0x18 + +#define DMA_SIZE (16*1024) /* Size of dma buffer - 16k */ + +#define CS8900 0x0000 +#define CS8920 0x4000 +#define CS8920M 0x6000 +#define REVISON_BITS 0x1F00 +#define EEVER_NUMBER 0x12 +#define CHKSUM_LEN 0x14 +#define CHKSUM_VAL 0x0000 +#define START_EEPROM_DATA 0x001c /* Offset into eeprom for start of data */ +#define IRQ_MAP_EEPROM_DATA 0x0046 /* Offset into eeprom for the IRQ map */ +#define IRQ_MAP_LEN 0x0004 /* No of bytes to read for the IRQ map */ +#define PNP_IRQ_FRMT 0x0022 /* PNP small item IRQ format */ +#define CS8900_IRQ_MAP 0x1c20 /* This IRQ map is fixed */ + +#define CS8920_NO_INTS 0x0F /* Max CS8920 interrupt select # */ + +#define PNP_ADD_PORT 0x0279 +#define PNP_WRITE_PORT 0x0A79 + +#define GET_PNP_ISA_STRUCT 0x40 +#define PNP_ISA_STRUCT_LEN 0x06 +#define PNP_CSN_CNT_OFF 0x01 +#define PNP_RD_PORT_OFF 0x02 +#define PNP_FUNCTION_OK 0x00 +#define PNP_WAKE 0x03 +#define PNP_RSRC_DATA 0x04 +#define PNP_RSRC_READY 0x01 +#define PNP_STATUS 0x05 +#define PNP_ACTIVATE 0x30 +#define PNP_CNF_IO_H 0x60 +#define PNP_CNF_IO_L 0x61 +#define PNP_CNF_INT 0x70 +#define PNP_CNF_DMA 0x74 +#define PNP_CNF_MEM 0x48 + +#define BIT0 1 +#define BIT15 0x8000 + |