diff options
author | Kalle Valo <kvalo@codeaurora.org> | 2015-11-17 18:57:38 (GMT) |
---|---|---|
committer | Kalle Valo <kvalo@codeaurora.org> | 2015-11-18 12:28:30 (GMT) |
commit | e705c12146aa9c69ca498d4ebb83ba7138f9b41f (patch) | |
tree | b55d4eb7a83c2ec117f460684eb71c89eee6a709 /drivers/net/wireless/intel/iwlwifi/iwl-csr.h | |
parent | 7ac9a364c1721a863ecc6cc9aba66e10114908db (diff) | |
download | linux-e705c12146aa9c69ca498d4ebb83ba7138f9b41f.tar.xz |
iwlwifi: move under intel vendor directory
Part of reorganising wireless drivers directory and Kconfig.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Diffstat (limited to 'drivers/net/wireless/intel/iwlwifi/iwl-csr.h')
-rw-r--r-- | drivers/net/wireless/intel/iwlwifi/iwl-csr.h | 552 |
1 files changed, 552 insertions, 0 deletions
diff --git a/drivers/net/wireless/intel/iwlwifi/iwl-csr.h b/drivers/net/wireless/intel/iwlwifi/iwl-csr.h new file mode 100644 index 0000000..543abea --- /dev/null +++ b/drivers/net/wireless/intel/iwlwifi/iwl-csr.h @@ -0,0 +1,552 @@ +/****************************************************************************** + * + * This file is provided under a dual BSD/GPLv2 license. When using or + * redistributing this file, you may do so under either license. + * + * GPL LICENSE SUMMARY + * + * Copyright(c) 2005 - 2014 Intel Corporation. All rights reserved. + * Copyright(c) 2013 - 2014 Intel Mobile Communications GmbH + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of version 2 of the GNU General Public License as + * published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, but + * WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU + * General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110, + * USA + * + * The full GNU General Public License is included in this distribution + * in the file called COPYING. + * + * Contact Information: + * Intel Linux Wireless <ilw@linux.intel.com> + * Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497 + * + * BSD LICENSE + * + * Copyright(c) 2005 - 2014 Intel Corporation. All rights reserved. + * Copyright(c) 2013 - 2014 Intel Mobile Communications GmbH + * All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * + * * Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * * Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in + * the documentation and/or other materials provided with the + * distribution. + * * Neither the name Intel Corporation nor the names of its + * contributors may be used to endorse or promote products derived + * from this software without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR + * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT + * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, + * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT + * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, + * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY + * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT + * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE + * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * + *****************************************************************************/ +#ifndef __iwl_csr_h__ +#define __iwl_csr_h__ +/* + * CSR (control and status registers) + * + * CSR registers are mapped directly into PCI bus space, and are accessible + * whenever platform supplies power to device, even when device is in + * low power states due to driver-invoked device resets + * (e.g. CSR_RESET_REG_FLAG_SW_RESET) or uCode-driven power-saving modes. + * + * Use iwl_write32() and iwl_read32() family to access these registers; + * these provide simple PCI bus access, without waking up the MAC. + * Do not use iwl_write_direct32() family for these registers; + * no need to "grab nic access" via CSR_GP_CNTRL_REG_FLAG_MAC_ACCESS_REQ. + * The MAC (uCode processor, etc.) does not need to be powered up for accessing + * the CSR registers. + * + * NOTE: Device does need to be awake in order to read this memory + * via CSR_EEPROM and CSR_OTP registers + */ +#define CSR_BASE (0x000) + +#define CSR_HW_IF_CONFIG_REG (CSR_BASE+0x000) /* hardware interface config */ +#define CSR_INT_COALESCING (CSR_BASE+0x004) /* accum ints, 32-usec units */ +#define CSR_INT (CSR_BASE+0x008) /* host interrupt status/ack */ +#define CSR_INT_MASK (CSR_BASE+0x00c) /* host interrupt enable */ +#define CSR_FH_INT_STATUS (CSR_BASE+0x010) /* busmaster int status/ack*/ +#define CSR_GPIO_IN (CSR_BASE+0x018) /* read external chip pins */ +#define CSR_RESET (CSR_BASE+0x020) /* busmaster enable, NMI, etc*/ +#define CSR_GP_CNTRL (CSR_BASE+0x024) + +/* 2nd byte of CSR_INT_COALESCING, not accessible via iwl_write32()! */ +#define CSR_INT_PERIODIC_REG (CSR_BASE+0x005) + +/* + * Hardware revision info + * Bit fields: + * 31-16: Reserved + * 15-4: Type of device: see CSR_HW_REV_TYPE_xxx definitions + * 3-2: Revision step: 0 = A, 1 = B, 2 = C, 3 = D + * 1-0: "Dash" (-) value, as in A-1, etc. + */ +#define CSR_HW_REV (CSR_BASE+0x028) + +/* + * EEPROM and OTP (one-time-programmable) memory reads + * + * NOTE: Device must be awake, initialized via apm_ops.init(), + * in order to read. + */ +#define CSR_EEPROM_REG (CSR_BASE+0x02c) +#define CSR_EEPROM_GP (CSR_BASE+0x030) +#define CSR_OTP_GP_REG (CSR_BASE+0x034) + +#define CSR_GIO_REG (CSR_BASE+0x03C) +#define CSR_GP_UCODE_REG (CSR_BASE+0x048) +#define CSR_GP_DRIVER_REG (CSR_BASE+0x050) + +/* + * UCODE-DRIVER GP (general purpose) mailbox registers. + * SET/CLR registers set/clear bit(s) if "1" is written. + */ +#define CSR_UCODE_DRV_GP1 (CSR_BASE+0x054) +#define CSR_UCODE_DRV_GP1_SET (CSR_BASE+0x058) +#define CSR_UCODE_DRV_GP1_CLR (CSR_BASE+0x05c) +#define CSR_UCODE_DRV_GP2 (CSR_BASE+0x060) + +#define CSR_MBOX_SET_REG (CSR_BASE + 0x88) + +#define CSR_LED_REG (CSR_BASE+0x094) +#define CSR_DRAM_INT_TBL_REG (CSR_BASE+0x0A0) +#define CSR_MAC_SHADOW_REG_CTRL (CSR_BASE+0x0A8) /* 6000 and up */ + + +/* GIO Chicken Bits (PCI Express bus link power management) */ +#define CSR_GIO_CHICKEN_BITS (CSR_BASE+0x100) + +/* Analog phase-lock-loop configuration */ +#define CSR_ANA_PLL_CFG (CSR_BASE+0x20c) + +/* + * CSR HW resources monitor registers + */ +#define CSR_MONITOR_CFG_REG (CSR_BASE+0x214) +#define CSR_MONITOR_STATUS_REG (CSR_BASE+0x228) +#define CSR_MONITOR_XTAL_RESOURCES (0x00000010) + +/* + * CSR Hardware Revision Workaround Register. Indicates hardware rev; + * "step" determines CCK backoff for txpower calculation. Used for 4965 only. + * See also CSR_HW_REV register. + * Bit fields: + * 3-2: 0 = A, 1 = B, 2 = C, 3 = D step + * 1-0: "Dash" (-) value, as in C-1, etc. + */ +#define CSR_HW_REV_WA_REG (CSR_BASE+0x22C) + +#define CSR_DBG_HPET_MEM_REG (CSR_BASE+0x240) +#define CSR_DBG_LINK_PWR_MGMT_REG (CSR_BASE+0x250) + +/* Bits for CSR_HW_IF_CONFIG_REG */ +#define CSR_HW_IF_CONFIG_REG_MSK_MAC_DASH (0x00000003) +#define CSR_HW_IF_CONFIG_REG_MSK_MAC_STEP (0x0000000C) +#define CSR_HW_IF_CONFIG_REG_MSK_BOARD_VER (0x000000C0) +#define CSR_HW_IF_CONFIG_REG_BIT_MAC_SI (0x00000100) +#define CSR_HW_IF_CONFIG_REG_BIT_RADIO_SI (0x00000200) +#define CSR_HW_IF_CONFIG_REG_MSK_PHY_TYPE (0x00000C00) +#define CSR_HW_IF_CONFIG_REG_MSK_PHY_DASH (0x00003000) +#define CSR_HW_IF_CONFIG_REG_MSK_PHY_STEP (0x0000C000) + +#define CSR_HW_IF_CONFIG_REG_POS_MAC_DASH (0) +#define CSR_HW_IF_CONFIG_REG_POS_MAC_STEP (2) +#define CSR_HW_IF_CONFIG_REG_POS_BOARD_VER (6) +#define CSR_HW_IF_CONFIG_REG_POS_PHY_TYPE (10) +#define CSR_HW_IF_CONFIG_REG_POS_PHY_DASH (12) +#define CSR_HW_IF_CONFIG_REG_POS_PHY_STEP (14) + +#define CSR_HW_IF_CONFIG_REG_BIT_HAP_WAKE_L1A (0x00080000) +#define CSR_HW_IF_CONFIG_REG_BIT_EEPROM_OWN_SEM (0x00200000) +#define CSR_HW_IF_CONFIG_REG_BIT_NIC_READY (0x00400000) /* PCI_OWN_SEM */ +#define CSR_HW_IF_CONFIG_REG_BIT_NIC_PREPARE_DONE (0x02000000) /* ME_OWN */ +#define CSR_HW_IF_CONFIG_REG_PREPARE (0x08000000) /* WAKE_ME */ +#define CSR_HW_IF_CONFIG_REG_ENABLE_PME (0x10000000) +#define CSR_HW_IF_CONFIG_REG_PERSIST_MODE (0x40000000) /* PERSISTENCE */ + +#define CSR_MBOX_SET_REG_OS_ALIVE BIT(5) + +#define CSR_INT_PERIODIC_DIS (0x00) /* disable periodic int*/ +#define CSR_INT_PERIODIC_ENA (0xFF) /* 255*32 usec ~ 8 msec*/ + +/* interrupt flags in INTA, set by uCode or hardware (e.g. dma), + * acknowledged (reset) by host writing "1" to flagged bits. */ +#define CSR_INT_BIT_FH_RX (1 << 31) /* Rx DMA, cmd responses, FH_INT[17:16] */ +#define CSR_INT_BIT_HW_ERR (1 << 29) /* DMA hardware error FH_INT[31] */ +#define CSR_INT_BIT_RX_PERIODIC (1 << 28) /* Rx periodic */ +#define CSR_INT_BIT_FH_TX (1 << 27) /* Tx DMA FH_INT[1:0] */ +#define CSR_INT_BIT_SCD (1 << 26) /* TXQ pointer advanced */ +#define CSR_INT_BIT_SW_ERR (1 << 25) /* uCode error */ +#define CSR_INT_BIT_PAGING (1 << 24) /* SDIO PAGING */ +#define CSR_INT_BIT_RF_KILL (1 << 7) /* HW RFKILL switch GP_CNTRL[27] toggled */ +#define CSR_INT_BIT_CT_KILL (1 << 6) /* Critical temp (chip too hot) rfkill */ +#define CSR_INT_BIT_SW_RX (1 << 3) /* Rx, command responses */ +#define CSR_INT_BIT_WAKEUP (1 << 1) /* NIC controller waking up (pwr mgmt) */ +#define CSR_INT_BIT_ALIVE (1 << 0) /* uCode interrupts once it initializes */ + +#define CSR_INI_SET_MASK (CSR_INT_BIT_FH_RX | \ + CSR_INT_BIT_HW_ERR | \ + CSR_INT_BIT_FH_TX | \ + CSR_INT_BIT_SW_ERR | \ + CSR_INT_BIT_PAGING | \ + CSR_INT_BIT_RF_KILL | \ + CSR_INT_BIT_SW_RX | \ + CSR_INT_BIT_WAKEUP | \ + CSR_INT_BIT_ALIVE | \ + CSR_INT_BIT_RX_PERIODIC) + +/* interrupt flags in FH (flow handler) (PCI busmaster DMA) */ +#define CSR_FH_INT_BIT_ERR (1 << 31) /* Error */ +#define CSR_FH_INT_BIT_HI_PRIOR (1 << 30) /* High priority Rx, bypass coalescing */ +#define CSR_FH_INT_BIT_RX_CHNL1 (1 << 17) /* Rx channel 1 */ +#define CSR_FH_INT_BIT_RX_CHNL0 (1 << 16) /* Rx channel 0 */ +#define CSR_FH_INT_BIT_TX_CHNL1 (1 << 1) /* Tx channel 1 */ +#define CSR_FH_INT_BIT_TX_CHNL0 (1 << 0) /* Tx channel 0 */ + +#define CSR_FH_INT_RX_MASK (CSR_FH_INT_BIT_HI_PRIOR | \ + CSR_FH_INT_BIT_RX_CHNL1 | \ + CSR_FH_INT_BIT_RX_CHNL0) + +#define CSR_FH_INT_TX_MASK (CSR_FH_INT_BIT_TX_CHNL1 | \ + CSR_FH_INT_BIT_TX_CHNL0) + +/* GPIO */ +#define CSR_GPIO_IN_BIT_AUX_POWER (0x00000200) +#define CSR_GPIO_IN_VAL_VAUX_PWR_SRC (0x00000000) +#define CSR_GPIO_IN_VAL_VMAIN_PWR_SRC (0x00000200) + +/* RESET */ +#define CSR_RESET_REG_FLAG_NEVO_RESET (0x00000001) +#define CSR_RESET_REG_FLAG_FORCE_NMI (0x00000002) +#define CSR_RESET_REG_FLAG_SW_RESET (0x00000080) +#define CSR_RESET_REG_FLAG_MASTER_DISABLED (0x00000100) +#define CSR_RESET_REG_FLAG_STOP_MASTER (0x00000200) +#define CSR_RESET_LINK_PWR_MGMT_DISABLED (0x80000000) + +/* + * GP (general purpose) CONTROL REGISTER + * Bit fields: + * 27: HW_RF_KILL_SW + * Indicates state of (platform's) hardware RF-Kill switch + * 26-24: POWER_SAVE_TYPE + * Indicates current power-saving mode: + * 000 -- No power saving + * 001 -- MAC power-down + * 010 -- PHY (radio) power-down + * 011 -- Error + * 10: XTAL ON request + * 9-6: SYS_CONFIG + * Indicates current system configuration, reflecting pins on chip + * as forced high/low by device circuit board. + * 4: GOING_TO_SLEEP + * Indicates MAC is entering a power-saving sleep power-down. + * Not a good time to access device-internal resources. + * 3: MAC_ACCESS_REQ + * Host sets this to request and maintain MAC wakeup, to allow host + * access to device-internal resources. Host must wait for + * MAC_CLOCK_READY (and !GOING_TO_SLEEP) before accessing non-CSR + * device registers. + * 2: INIT_DONE + * Host sets this to put device into fully operational D0 power mode. + * Host resets this after SW_RESET to put device into low power mode. + * 0: MAC_CLOCK_READY + * Indicates MAC (ucode processor, etc.) is powered up and can run. + * Internal resources are accessible. + * NOTE: This does not indicate that the processor is actually running. + * NOTE: This does not indicate that device has completed + * init or post-power-down restore of internal SRAM memory. + * Use CSR_UCODE_DRV_GP1_BIT_MAC_SLEEP as indication that + * SRAM is restored and uCode is in normal operation mode. + * Later devices (5xxx/6xxx/1xxx) use non-volatile SRAM, and + * do not need to save/restore it. + * NOTE: After device reset, this bit remains "0" until host sets + * INIT_DONE + */ +#define CSR_GP_CNTRL_REG_FLAG_MAC_CLOCK_READY (0x00000001) +#define CSR_GP_CNTRL_REG_FLAG_INIT_DONE (0x00000004) +#define CSR_GP_CNTRL_REG_FLAG_MAC_ACCESS_REQ (0x00000008) +#define CSR_GP_CNTRL_REG_FLAG_GOING_TO_SLEEP (0x00000010) +#define CSR_GP_CNTRL_REG_FLAG_XTAL_ON (0x00000400) + +#define CSR_GP_CNTRL_REG_VAL_MAC_ACCESS_EN (0x00000001) + +#define CSR_GP_CNTRL_REG_MSK_POWER_SAVE_TYPE (0x07000000) +#define CSR_GP_CNTRL_REG_FLAG_MAC_POWER_SAVE (0x04000000) +#define CSR_GP_CNTRL_REG_FLAG_HW_RF_KILL_SW (0x08000000) + + +/* HW REV */ +#define CSR_HW_REV_DASH(_val) (((_val) & 0x0000003) >> 0) +#define CSR_HW_REV_STEP(_val) (((_val) & 0x000000C) >> 2) + + +/** + * hw_rev values + */ +enum { + SILICON_A_STEP = 0, + SILICON_B_STEP, + SILICON_C_STEP, +}; + + +#define CSR_HW_REV_TYPE_MSK (0x000FFF0) +#define CSR_HW_REV_TYPE_5300 (0x0000020) +#define CSR_HW_REV_TYPE_5350 (0x0000030) +#define CSR_HW_REV_TYPE_5100 (0x0000050) +#define CSR_HW_REV_TYPE_5150 (0x0000040) +#define CSR_HW_REV_TYPE_1000 (0x0000060) +#define CSR_HW_REV_TYPE_6x00 (0x0000070) +#define CSR_HW_REV_TYPE_6x50 (0x0000080) +#define CSR_HW_REV_TYPE_6150 (0x0000084) +#define CSR_HW_REV_TYPE_6x05 (0x00000B0) +#define CSR_HW_REV_TYPE_6x30 CSR_HW_REV_TYPE_6x05 +#define CSR_HW_REV_TYPE_6x35 CSR_HW_REV_TYPE_6x05 +#define CSR_HW_REV_TYPE_2x30 (0x00000C0) +#define CSR_HW_REV_TYPE_2x00 (0x0000100) +#define CSR_HW_REV_TYPE_105 (0x0000110) +#define CSR_HW_REV_TYPE_135 (0x0000120) +#define CSR_HW_REV_TYPE_7265D (0x0000210) +#define CSR_HW_REV_TYPE_NONE (0x00001F0) + +/* EEPROM REG */ +#define CSR_EEPROM_REG_READ_VALID_MSK (0x00000001) +#define CSR_EEPROM_REG_BIT_CMD (0x00000002) +#define CSR_EEPROM_REG_MSK_ADDR (0x0000FFFC) +#define CSR_EEPROM_REG_MSK_DATA (0xFFFF0000) + +/* EEPROM GP */ +#define CSR_EEPROM_GP_VALID_MSK (0x00000007) /* signature */ +#define CSR_EEPROM_GP_IF_OWNER_MSK (0x00000180) +#define CSR_EEPROM_GP_BAD_SIGNATURE_BOTH_EEP_AND_OTP (0x00000000) +#define CSR_EEPROM_GP_BAD_SIG_EEP_GOOD_SIG_OTP (0x00000001) +#define CSR_EEPROM_GP_GOOD_SIG_EEP_LESS_THAN_4K (0x00000002) +#define CSR_EEPROM_GP_GOOD_SIG_EEP_MORE_THAN_4K (0x00000004) + +/* One-time-programmable memory general purpose reg */ +#define CSR_OTP_GP_REG_DEVICE_SELECT (0x00010000) /* 0 - EEPROM, 1 - OTP */ +#define CSR_OTP_GP_REG_OTP_ACCESS_MODE (0x00020000) /* 0 - absolute, 1 - relative */ +#define CSR_OTP_GP_REG_ECC_CORR_STATUS_MSK (0x00100000) /* bit 20 */ +#define CSR_OTP_GP_REG_ECC_UNCORR_STATUS_MSK (0x00200000) /* bit 21 */ + +/* GP REG */ +#define CSR_GP_REG_POWER_SAVE_STATUS_MSK (0x03000000) /* bit 24/25 */ +#define CSR_GP_REG_NO_POWER_SAVE (0x00000000) +#define CSR_GP_REG_MAC_POWER_SAVE (0x01000000) +#define CSR_GP_REG_PHY_POWER_SAVE (0x02000000) +#define CSR_GP_REG_POWER_SAVE_ERROR (0x03000000) + + +/* CSR GIO */ +#define CSR_GIO_REG_VAL_L0S_ENABLED (0x00000002) + +/* + * UCODE-DRIVER GP (general purpose) mailbox register 1 + * Host driver and uCode write and/or read this register to communicate with + * each other. + * Bit fields: + * 4: UCODE_DISABLE + * Host sets this to request permanent halt of uCode, same as + * sending CARD_STATE command with "halt" bit set. + * 3: CT_KILL_EXIT + * Host sets this to request exit from CT_KILL state, i.e. host thinks + * device temperature is low enough to continue normal operation. + * 2: CMD_BLOCKED + * Host sets this during RF KILL power-down sequence (HW, SW, CT KILL) + * to release uCode to clear all Tx and command queues, enter + * unassociated mode, and power down. + * NOTE: Some devices also use HBUS_TARG_MBX_C register for this bit. + * 1: SW_BIT_RFKILL + * Host sets this when issuing CARD_STATE command to request + * device sleep. + * 0: MAC_SLEEP + * uCode sets this when preparing a power-saving power-down. + * uCode resets this when power-up is complete and SRAM is sane. + * NOTE: device saves internal SRAM data to host when powering down, + * and must restore this data after powering back up. + * MAC_SLEEP is the best indication that restore is complete. + * Later devices (5xxx/6xxx/1xxx) use non-volatile SRAM, and + * do not need to save/restore it. + */ +#define CSR_UCODE_DRV_GP1_BIT_MAC_SLEEP (0x00000001) +#define CSR_UCODE_SW_BIT_RFKILL (0x00000002) +#define CSR_UCODE_DRV_GP1_BIT_CMD_BLOCKED (0x00000004) +#define CSR_UCODE_DRV_GP1_REG_BIT_CT_KILL_EXIT (0x00000008) +#define CSR_UCODE_DRV_GP1_BIT_D3_CFG_COMPLETE (0x00000020) + +/* GP Driver */ +#define CSR_GP_DRIVER_REG_BIT_RADIO_SKU_MSK (0x00000003) +#define CSR_GP_DRIVER_REG_BIT_RADIO_SKU_3x3_HYB (0x00000000) +#define CSR_GP_DRIVER_REG_BIT_RADIO_SKU_2x2_HYB (0x00000001) +#define CSR_GP_DRIVER_REG_BIT_RADIO_SKU_2x2_IPA (0x00000002) +#define CSR_GP_DRIVER_REG_BIT_CALIB_VERSION6 (0x00000004) +#define CSR_GP_DRIVER_REG_BIT_6050_1x2 (0x00000008) + +#define CSR_GP_DRIVER_REG_BIT_RADIO_IQ_INVER (0x00000080) + +/* GIO Chicken Bits (PCI Express bus link power management) */ +#define CSR_GIO_CHICKEN_BITS_REG_BIT_L1A_NO_L0S_RX (0x00800000) +#define CSR_GIO_CHICKEN_BITS_REG_BIT_DIS_L0S_EXIT_TIMER (0x20000000) + +/* LED */ +#define CSR_LED_BSM_CTRL_MSK (0xFFFFFFDF) +#define CSR_LED_REG_TURN_ON (0x60) +#define CSR_LED_REG_TURN_OFF (0x20) + +/* ANA_PLL */ +#define CSR50_ANA_PLL_CFG_VAL (0x00880300) + +/* HPET MEM debug */ +#define CSR_DBG_HPET_MEM_REG_VAL (0xFFFF0000) + +/* DRAM INT TABLE */ +#define CSR_DRAM_INT_TBL_ENABLE (1 << 31) +#define CSR_DRAM_INIT_TBL_WRITE_POINTER (1 << 28) +#define CSR_DRAM_INIT_TBL_WRAP_CHECK (1 << 27) + +/* + * SHR target access (Shared block memory space) + * + * Shared internal registers can be accessed directly from PCI bus through SHR + * arbiter without need for the MAC HW to be powered up. This is possible due to + * indirect read/write via HEEP_CTRL_WRD_PCIEX_CTRL (0xEC) and + * HEEP_CTRL_WRD_PCIEX_DATA (0xF4) registers. + * + * Use iwl_write32()/iwl_read32() family to access these registers. The MAC HW + * need not be powered up so no "grab inc access" is required. + */ + +/* + * Registers for accessing shared registers (e.g. SHR_APMG_GP1, + * SHR_APMG_XTAL_CFG). For example, to read from SHR_APMG_GP1 register (0x1DC), + * first, write to the control register: + * HEEP_CTRL_WRD_PCIEX_CTRL[15:0] = 0x1DC (offset of the SHR_APMG_GP1 register) + * HEEP_CTRL_WRD_PCIEX_CTRL[29:28] = 2 (read access) + * second, read from the data register HEEP_CTRL_WRD_PCIEX_DATA[31:0]. + * + * To write the register, first, write to the data register + * HEEP_CTRL_WRD_PCIEX_DATA[31:0] and then: + * HEEP_CTRL_WRD_PCIEX_CTRL[15:0] = 0x1DC (offset of the SHR_APMG_GP1 register) + * HEEP_CTRL_WRD_PCIEX_CTRL[29:28] = 3 (write access) + */ +#define HEEP_CTRL_WRD_PCIEX_CTRL_REG (CSR_BASE+0x0ec) +#define HEEP_CTRL_WRD_PCIEX_DATA_REG (CSR_BASE+0x0f4) + +/* + * HBUS (Host-side Bus) + * + * HBUS registers are mapped directly into PCI bus space, but are used + * to indirectly access device's internal memory or registers that + * may be powered-down. + * + * Use iwl_write_direct32()/iwl_read_direct32() family for these registers; + * host must "grab nic access" via CSR_GP_CNTRL_REG_FLAG_MAC_ACCESS_REQ + * to make sure the MAC (uCode processor, etc.) is powered up for accessing + * internal resources. + * + * Do not use iwl_write32()/iwl_read32() family to access these registers; + * these provide only simple PCI bus access, without waking up the MAC. + */ +#define HBUS_BASE (0x400) + +/* + * Registers for accessing device's internal SRAM memory (e.g. SCD SRAM + * structures, error log, event log, verifying uCode load). + * First write to address register, then read from or write to data register + * to complete the job. Once the address register is set up, accesses to + * data registers auto-increment the address by one dword. + * Bit usage for address registers (read or write): + * 0-31: memory address within device + */ +#define HBUS_TARG_MEM_RADDR (HBUS_BASE+0x00c) +#define HBUS_TARG_MEM_WADDR (HBUS_BASE+0x010) +#define HBUS_TARG_MEM_WDAT (HBUS_BASE+0x018) +#define HBUS_TARG_MEM_RDAT (HBUS_BASE+0x01c) + +/* Mailbox C, used as workaround alternative to CSR_UCODE_DRV_GP1 mailbox */ +#define HBUS_TARG_MBX_C (HBUS_BASE+0x030) +#define HBUS_TARG_MBX_C_REG_BIT_CMD_BLOCKED (0x00000004) + +/* + * Registers for accessing device's internal peripheral registers + * (e.g. SCD, BSM, etc.). First write to address register, + * then read from or write to data register to complete the job. + * Bit usage for address registers (read or write): + * 0-15: register address (offset) within device + * 24-25: (# bytes - 1) to read or write (e.g. 3 for dword) + */ +#define HBUS_TARG_PRPH_WADDR (HBUS_BASE+0x044) +#define HBUS_TARG_PRPH_RADDR (HBUS_BASE+0x048) +#define HBUS_TARG_PRPH_WDAT (HBUS_BASE+0x04c) +#define HBUS_TARG_PRPH_RDAT (HBUS_BASE+0x050) + +/* Used to enable DBGM */ +#define HBUS_TARG_TEST_REG (HBUS_BASE+0x05c) + +/* + * Per-Tx-queue write pointer (index, really!) + * Indicates index to next TFD that driver will fill (1 past latest filled). + * Bit usage: + * 0-7: queue write index + * 11-8: queue selector + */ +#define HBUS_TARG_WRPTR (HBUS_BASE+0x060) + +/********************************************************** + * CSR values + **********************************************************/ + /* + * host interrupt timeout value + * used with setting interrupt coalescing timer + * the CSR_INT_COALESCING is an 8 bit register in 32-usec unit + * + * default interrupt coalescing timer is 64 x 32 = 2048 usecs + */ +#define IWL_HOST_INT_TIMEOUT_MAX (0xFF) +#define IWL_HOST_INT_TIMEOUT_DEF (0x40) +#define IWL_HOST_INT_TIMEOUT_MIN (0x0) +#define IWL_HOST_INT_OPER_MODE BIT(31) + +/***************************************************************************** + * 7000/3000 series SHR DTS addresses * + *****************************************************************************/ + +/* Diode Results Register Structure: */ +enum dtd_diode_reg { + DTS_DIODE_REG_DIG_VAL = 0x000000FF, /* bits [7:0] */ + DTS_DIODE_REG_VREF_LOW = 0x0000FF00, /* bits [15:8] */ + DTS_DIODE_REG_VREF_HIGH = 0x00FF0000, /* bits [23:16] */ + DTS_DIODE_REG_VREF_ID = 0x03000000, /* bits [25:24] */ + DTS_DIODE_REG_PASS_ONCE = 0x80000000, /* bits [31:31] */ + DTS_DIODE_REG_FLAGS_MSK = 0xFF000000, /* bits [31:24] */ +/* Those are the masks INSIDE the flags bit-field: */ + DTS_DIODE_REG_FLAGS_VREFS_ID_POS = 0, + DTS_DIODE_REG_FLAGS_VREFS_ID = 0x00000003, /* bits [1:0] */ + DTS_DIODE_REG_FLAGS_PASS_ONCE_POS = 7, + DTS_DIODE_REG_FLAGS_PASS_ONCE = 0x00000080, /* bits [7:7] */ +}; + +#endif /* !__iwl_csr_h__ */ |