e1000e: cleanup use of check_reset_block function pointer

Replace e1000_check_reset_block() inline function with calls to the PHY ops
check_reset_block function pointer.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

6 files changed, 16 insertions, 18 deletions

diff --git a/drivers/net/ethernet/intel/e1000e/e1000.h b/drivers/net/ethernet/intel/e1000e/e1000.h
index bae094b..f93d7a4 100644
--- a/drivers/net/ethernet/intel/e1000e/e1000.h
+++ b/drivers/net/ethernet/intel/e1000e/e1000.h
@@ -662,11 +662,6 @@ static inline s32 e1000_phy_hw_reset(struct e1000_hw *hw)
 	return hw->phy.ops.reset(hw);
 }
 
-static inline s32 e1000_check_reset_block(struct e1000_hw *hw)
-{
-	return hw->phy.ops.check_reset_block(hw);
-}
-
 static inline s32 e1e_rphy(struct e1000_hw *hw, u32 offset, u16 *data)
 {
 	return hw->phy.ops.read_reg(hw, offset, data);
diff --git a/drivers/net/ethernet/intel/e1000e/ethtool.c b/drivers/net/ethernet/intel/e1000e/ethtool.c
index b1f5d74..db35dd5 100644
--- a/drivers/net/ethernet/intel/e1000e/ethtool.c
+++ b/drivers/net/ethernet/intel/e1000e/ethtool.c
@@ -258,7 +258,7 @@ static int e1000_set_settings(struct net_device *netdev,
 	 * When SoL/IDER sessions are active, autoneg/speed/duplex
 	 * cannot be changed
 	 */
-	if (e1000_check_reset_block(hw)) {
+	if (hw->phy.ops.check_reset_block(hw)) {
 		e_err("Cannot change link characteristics when SoL/IDER is "
 		      "active.\n");
 		return -EINVAL;
@@ -1598,11 +1598,13 @@ static int e1000_run_loopback_test(struct e1000_adapter *adapter)
 
 static int e1000_loopback_test(struct e1000_adapter *adapter, u64 *data)
 {
+	struct e1000_hw *hw = &adapter->hw;
+
 	/*
 	 * PHY loopback cannot be performed if SoL/IDER
 	 * sessions are active
 	 */
-	if (e1000_check_reset_block(&adapter->hw)) {
+	if (hw->phy.ops.check_reset_block(hw)) {
 		e_err("Cannot do PHY loopback test when SoL/IDER is active.\n");
 		*data = 0;
 		goto out;
diff --git a/drivers/net/ethernet/intel/e1000e/ich8lan.c b/drivers/net/ethernet/intel/e1000e/ich8lan.c
index 8b9bf94..da89e2b 100644
--- a/drivers/net/ethernet/intel/e1000e/ich8lan.c
+++ b/drivers/net/ethernet/intel/e1000e/ich8lan.c
@@ -324,7 +324,7 @@ static s32 e1000_init_phy_params_pchlan(struct e1000_hw *hw)
 	phy->ops.power_down           = e1000_power_down_phy_copper_ich8lan;
 	phy->autoneg_mask             = AUTONEG_ADVERTISE_SPEED_DEFAULT;
 
-	if (!e1000_check_reset_block(hw)) {
+	if (!hw->phy.ops.check_reset_block(hw)) {
 		u32 fwsm = er32(FWSM);
 
 		/*
@@ -1314,7 +1314,7 @@ static s32 e1000_oem_bits_config_ich8lan(struct e1000_hw *hw, bool d0_state)
 			oem_reg |= HV_OEM_BITS_LPLU;
 
 		/* Set Restart auto-neg to activate the bits */
-		if (!e1000_check_reset_block(hw))
+		if (!hw->phy.ops.check_reset_block(hw))
 			oem_reg |= HV_OEM_BITS_RESTART_AN;
 	} else {
 		if (mac_reg & (E1000_PHY_CTRL_GBE_DISABLE |
@@ -1788,7 +1788,7 @@ static s32 e1000_post_phy_reset_ich8lan(struct e1000_hw *hw)
 	s32 ret_val = 0;
 	u16 reg;
 
-	if (e1000_check_reset_block(hw))
+	if (hw->phy.ops.check_reset_block(hw))
 		return 0;
 
 	/* Allow time for h/w to get to quiescent state after reset */
@@ -1897,7 +1897,7 @@ static s32 e1000_set_lplu_state_pchlan(struct e1000_hw *hw, bool active)
 	else
 		oem_reg &= ~HV_OEM_BITS_LPLU;
 
-	if (!e1000_check_reset_block(hw))
+	if (!hw->phy.ops.check_reset_block(hw))
 		oem_reg |= HV_OEM_BITS_RESTART_AN;
 
 	return e1e_wphy(hw, HV_OEM_BITS, oem_reg);
@@ -3109,7 +3109,7 @@ static s32 e1000_reset_hw_ich8lan(struct e1000_hw *hw)
 
 	ctrl = er32(CTRL);
 
-	if (!e1000_check_reset_block(hw)) {
+	if (!hw->phy.ops.check_reset_block(hw)) {
 		/*
 		 * Full-chip reset requires MAC and PHY reset at the same
 		 * time to make sure the interface between MAC and the
@@ -3327,7 +3327,7 @@ static s32 e1000_setup_link_ich8lan(struct e1000_hw *hw)
 {
 	s32 ret_val;
 
-	if (e1000_check_reset_block(hw))
+	if (hw->phy.ops.check_reset_block(hw))
 		return 0;
 
 	/*
@@ -3707,7 +3707,8 @@ void e1000_resume_workarounds_pchlan(struct e1000_hw *hw)
 	u16 phy_id1, phy_id2;
 	s32 ret_val;
 
-	if ((hw->mac.type != e1000_pch2lan) || e1000_check_reset_block(hw))
+	if ((hw->mac.type != e1000_pch2lan) ||
+	    hw->phy.ops.check_reset_block(hw))
 		return;
 
 	ret_val = hw->phy.ops.acquire(hw);
diff --git a/drivers/net/ethernet/intel/e1000e/mac.c b/drivers/net/ethernet/intel/e1000e/mac.c
index 6e48895..011d83d 100644
--- a/drivers/net/ethernet/intel/e1000e/mac.c
+++ b/drivers/net/ethernet/intel/e1000e/mac.c
@@ -711,7 +711,7 @@ s32 e1000e_setup_link_generic(struct e1000_hw *hw)
 	 * In the case of the phy reset being blocked, we already have a link.
 	 * We do not need to set it up again.
 	 */
-	if (e1000_check_reset_block(hw))
+	if (hw->phy.ops.check_reset_block(hw))
 		return 0;
 
 	/*
diff --git a/drivers/net/ethernet/intel/e1000e/netdev.c b/drivers/net/ethernet/intel/e1000e/netdev.c
index c30e99e..3975ed1 100644
--- a/drivers/net/ethernet/intel/e1000e/netdev.c
+++ b/drivers/net/ethernet/intel/e1000e/netdev.c
@@ -6236,7 +6236,7 @@ static int __devinit e1000_probe(struct pci_dev *pdev,
 		adapter->hw.phy.ms_type = e1000_ms_hw_default;
 	}
 
-	if (e1000_check_reset_block(&adapter->hw))
+	if (hw->phy.ops.check_reset_block(hw))
 		e_info("PHY reset is blocked due to SOL/IDER session.\n");
 
 	/* Set initial default active device features */
@@ -6403,7 +6403,7 @@ err_register:
 	if (!(adapter->flags & FLAG_HAS_AMT))
 		e1000e_release_hw_control(adapter);
 err_eeprom:
-	if (!e1000_check_reset_block(&adapter->hw))
+	if (!hw->phy.ops.check_reset_block(hw))
 		e1000_phy_hw_reset(&adapter->hw);
 err_hw_init:
 	kfree(adapter->tx_ring);
diff --git a/drivers/net/ethernet/intel/e1000e/phy.c b/drivers/net/ethernet/intel/e1000e/phy.c
index d4dbbe7..d10b27f 100644
--- a/drivers/net/ethernet/intel/e1000e/phy.c
+++ b/drivers/net/ethernet/intel/e1000e/phy.c
@@ -2133,7 +2133,7 @@ s32 e1000e_phy_hw_reset_generic(struct e1000_hw *hw)
 	s32 ret_val;
 	u32 ctrl;
 
-	ret_val = e1000_check_reset_block(hw);
+	ret_val = phy->ops.check_reset_block(hw);
 	if (ret_val)
 		return 0;