[SCSI] hpsa: Fix hard reset code.

Smart Array controllers newer than the P600 do not honor the
PCI power state method of resetting the controllers.  Instead,
in these cases we can get them to reset via the "doorbell" register.

This escaped notice until we began using "performant" mode because
the fact that the controllers did not reset did not normally
impede subsequent operation, and so things generally appeared to
"work".  Once the performant mode code was added, if the controller
does not reset, it remains in performant mode.  The code immediately
after the reset presumes the controller is in "simple" mode
(which previously, it had remained in simple mode the whole time).
If the controller remains in performant mode any code which presumes
it is in simple mode will not work.  So the reset needs to be fixed.

Unfortunately there are some controllers which cannot be reset by
either method. (eg. p800).  We detect these cases by noticing that
the controller seems to remain in performant mode even after a
reset has been attempted.  In those case, we proceed anyway,
as if the reset has happened (and skip the step of waiting for
the controller to become ready -- which is expecting it to be in
"simple" mode.)  To sum up, we try to do a better job of resetting
the controller if "reset_devices" is set, and if it doesn't work,
we print a message and try to continue anyway.

Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

1 files changed, 133 insertions, 41 deletions

diff --git a/drivers/scsi/hpsa.c b/drivers/scsi/hpsa.c
index b2f4785..f57d533 100644
--- a/drivers/scsi/hpsa.c
+++ b/drivers/scsi/hpsa.c
@@ -174,6 +174,11 @@ static void calc_bucket_map(int *bucket, int num_buckets,
 	int nsgs, int *bucket_map);
 static __devinit void hpsa_put_ctlr_into_performant_mode(struct ctlr_info *h);
 static inline u32 next_command(struct ctlr_info *h);
+static int __devinit hpsa_find_cfg_addrs(struct pci_dev *pdev,
+	void __iomem *vaddr, u32 *cfg_base_addr, u64 *cfg_base_addr_index,
+	u64 *cfg_offset);
+static int __devinit hpsa_pci_find_memory_BAR(struct pci_dev *pdev,
+	unsigned long *memory_bar);
 
 static DEVICE_ATTR(raid_level, S_IRUGO, raid_level_show, NULL);
 static DEVICE_ATTR(lunid, S_IRUGO, lunid_show, NULL);
@@ -3078,17 +3083,75 @@ static __devinit int hpsa_reset_msi(struct pci_dev *pdev)
 	return 0;
 }
 
+static int hpsa_controller_hard_reset(struct pci_dev *pdev,
+	void * __iomem vaddr, bool use_doorbell)
+{
+	u16 pmcsr;
+	int pos;
+
+	if (use_doorbell) {
+		/* For everything after the P600, the PCI power state method
+		 * of resetting the controller doesn't work, so we have this
+		 * other way using the doorbell register.
+		 */
+		dev_info(&pdev->dev, "using doorbell to reset controller\n");
+		writel(DOORBELL_CTLR_RESET, vaddr + SA5_DOORBELL);
+		msleep(1000);
+	} else { /* Try to do it the PCI power state way */
+
+		/* Quoting from the Open CISS Specification: "The Power
+		 * Management Control/Status Register (CSR) controls the power
+		 * state of the device.  The normal operating state is D0,
+		 * CSR=00h.  The software off state is D3, CSR=03h.  To reset
+		 * the controller, place the interface device in D3 then to D0,
+		 * this causes a secondary PCI reset which will reset the
+		 * controller." */
+
+		pos = pci_find_capability(pdev, PCI_CAP_ID_PM);
+		if (pos == 0) {
+			dev_err(&pdev->dev,
+				"hpsa_reset_controller: "
+				"PCI PM not supported\n");
+			return -ENODEV;
+		}
+		dev_info(&pdev->dev, "using PCI PM to reset controller\n");
+		/* enter the D3hot power management state */
+		pci_read_config_word(pdev, pos + PCI_PM_CTRL, &pmcsr);
+		pmcsr &= ~PCI_PM_CTRL_STATE_MASK;
+		pmcsr |= PCI_D3hot;
+		pci_write_config_word(pdev, pos + PCI_PM_CTRL, pmcsr);
+
+		msleep(500);
+
+		/* enter the D0 power management state */
+		pmcsr &= ~PCI_PM_CTRL_STATE_MASK;
+		pmcsr |= PCI_D0;
+		pci_write_config_word(pdev, pos + PCI_PM_CTRL, pmcsr);
+
+		msleep(500);
+	}
+	return 0;
+}
+
 /* This does a hard reset of the controller using PCI power management
- * states.
+ * states or the using the doorbell register.
  */
-static __devinit int hpsa_hard_reset_controller(struct pci_dev *pdev)
+static __devinit int hpsa_kdump_hard_reset_controller(struct pci_dev *pdev)
 {
-	u16 pmcsr, saved_config_space[32];
-	int i, pos;
+	u16 saved_config_space[32];
+	u64 cfg_offset;
+	u32 cfg_base_addr;
+	u64 cfg_base_addr_index;
+	void __iomem *vaddr;
+	unsigned long paddr;
+	u32 misc_fw_support, active_transport;
+	int rc, i;
+	struct CfgTable __iomem *cfgtable;
+	bool use_doorbell;
 
-	dev_info(&pdev->dev, "using PCI PM to reset controller\n");
 
-	/* This is very nearly the same thing as
+	/* For controllers as old as the P600, this is very nearly
+	 * the same thing as
 	 *
 	 * pci_save_state(pci_dev);
 	 * pci_set_power_state(pci_dev, PCI_D3hot);
@@ -3102,41 +3165,42 @@ static __devinit int hpsa_hard_reset_controller(struct pci_dev *pdev)
 	 * violate the ordering requirements for restoring the
 	 * configuration space from the CCISS document (see the
 	 * comment below).  So we roll our own ....
+	 *
+	 * For controllers newer than the P600, the pci power state
+	 * method of resetting doesn't work so we have another way
+	 * using the doorbell register.
 	 */
-
 	for (i = 0; i < 32; i++)
 		pci_read_config_word(pdev, 2*i, &saved_config_space[i]);
 
-	pos = pci_find_capability(pdev, PCI_CAP_ID_PM);
-	if (pos == 0) {
-		dev_err(&pdev->dev,
-			"hpsa_reset_controller: PCI PM not supported\n");
-		return -ENODEV;
-	}
-
-	/* Quoting from the Open CISS Specification: "The Power
-	 * Management Control/Status Register (CSR) controls the power
-	 * state of the device.  The normal operating state is D0,
-	 * CSR=00h.  The software off state is D3, CSR=03h.  To reset
-	 * the controller, place the interface device in D3 then to
-	 * D0, this causes a secondary PCI reset which will reset the
-	 * controller."
-	 */
 
-	/* enter the D3hot power management state */
-	pci_read_config_word(pdev, pos + PCI_PM_CTRL, &pmcsr);
-	pmcsr &= ~PCI_PM_CTRL_STATE_MASK;
-	pmcsr |= PCI_D3hot;
-	pci_write_config_word(pdev, pos + PCI_PM_CTRL, pmcsr);
+	/* find the first memory BAR, so we can find the cfg table */
+	rc = hpsa_pci_find_memory_BAR(pdev, &paddr);
+	if (rc)
+		return rc;
+	vaddr = remap_pci_mem(paddr, 0x250);
+	if (!vaddr)
+		return -ENOMEM;
 
-	msleep(500);
+	/* find cfgtable in order to check if reset via doorbell is supported */
+	rc = hpsa_find_cfg_addrs(pdev, vaddr, &cfg_base_addr,
+					&cfg_base_addr_index, &cfg_offset);
+	if (rc)
+		goto unmap_vaddr;
+	cfgtable = remap_pci_mem(pci_resource_start(pdev,
+		       cfg_base_addr_index) + cfg_offset, sizeof(*cfgtable));
+	if (!cfgtable) {
+		rc = -ENOMEM;
+		goto unmap_vaddr;
+	}
 
-	/* enter the D0 power management state */
-	pmcsr &= ~PCI_PM_CTRL_STATE_MASK;
-	pmcsr |= PCI_D0;
-	pci_write_config_word(pdev, pos + PCI_PM_CTRL, pmcsr);
+	/* If reset via doorbell register is supported, use that. */
+	misc_fw_support = readl(&cfgtable->misc_fw_support);
+	use_doorbell = misc_fw_support & MISC_FW_DOORBELL_RESET;
 
-	msleep(500);
+	rc = hpsa_controller_hard_reset(pdev, vaddr, use_doorbell);
+	if (rc)
+		goto unmap_cfgtable;
 
 	/* Restore the PCI configuration space.  The Open CISS
 	 * Specification says, "Restore the PCI Configuration
@@ -3153,7 +3217,29 @@ static __devinit int hpsa_hard_reset_controller(struct pci_dev *pdev)
 	wmb();
 	pci_write_config_word(pdev, 4, saved_config_space[2]);
 
-	return 0;
+	/* Some devices (notably the HP Smart Array 5i Controller)
+	   need a little pause here */
+	msleep(HPSA_POST_RESET_PAUSE_MSECS);
+
+	/* Controller should be in simple mode at this point.  If it's not,
+	 * It means we're on one of those controllers which doesn't support
+	 * the doorbell reset method and on which the PCI power management reset
+	 * method doesn't work (P800, for example.)
+	 * In those cases, pretend the reset worked and hope for the best.
+	 */
+	active_transport = readl(&cfgtable->TransportActive);
+	if (active_transport & PERFORMANT_MODE) {
+		dev_warn(&pdev->dev, "Unable to successfully reset controller,"
+			" proceeding anyway.\n");
+		rc = -ENOTSUPP;
+	}
+
+unmap_cfgtable:
+	iounmap(cfgtable);
+
+unmap_vaddr:
+	iounmap(vaddr);
+	return rc;
 }
 
 /*
@@ -3573,18 +3659,24 @@ static void __devinit hpsa_hba_inquiry(struct ctlr_info *h)
 
 static __devinit int hpsa_init_reset_devices(struct pci_dev *pdev)
 {
-	int i;
+	int rc, i;
 
 	if (!reset_devices)
 		return 0;
 
-	/* Reset the controller with a PCI power-cycle */
-	if (hpsa_hard_reset_controller(pdev) || hpsa_reset_msi(pdev))
-		return -ENODEV;
+	/* Reset the controller with a PCI power-cycle or via doorbell */
+	rc = hpsa_kdump_hard_reset_controller(pdev);
 
-	/* Some devices (notably the HP Smart Array 5i Controller)
-	   need a little pause here */
-	msleep(HPSA_POST_RESET_PAUSE_MSECS);
+	/* -ENOTSUPP here means we cannot reset the controller
+	 * but it's already (and still) up and running in
+	 * "performant mode".
+	 */
+	if (rc == -ENOTSUPP)
+		return 0; /* just try to do the kdump anyhow. */
+	if (rc)
+		return -ENODEV;
+	if (hpsa_reset_msi(pdev))
+		return -ENODEV;
 
 	/* Now try to get the controller to respond to a no-op */
 	for (i = 0; i < HPSA_POST_RESET_NOOP_RETRIES; i++) {