[SCSI] isci: initial sgpio write support

Basic support to initialize the gpio unit, accept an incomming
SAS_GPIO_REG_TX_GP bitstream, and translate it to the ODx.n fields in
the hardware registers.  If register indexes outside the supported range
are specified in the SMP frame we simply accept the write and return how
many registers (SFF-8485) were written (libsas reports this as residue
in the request).

Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

1 files changed, 69 insertions, 0 deletions

diff --git a/drivers/scsi/isci/host.c b/drivers/scsi/isci/host.c
index 6981b77..f07f30f 100644
--- a/drivers/scsi/isci/host.c
+++ b/drivers/scsi/isci/host.c
@@ -1263,6 +1263,10 @@ void isci_host_deinit(struct isci_host *ihost)
 {
 	int i;
 
+	/* disable output data selects */
+	for (i = 0; i < isci_gpio_count(ihost); i++)
+		writel(SGPIO_HW_CONTROL, &ihost->scu_registers->peg0.sgpio.output_data_select[i]);
+
 	isci_host_change_state(ihost, isci_stopping);
 	for (i = 0; i < SCI_MAX_PORTS; i++) {
 		struct isci_port *iport = &ihost->ports[i];
@@ -1281,6 +1285,12 @@ void isci_host_deinit(struct isci_host *ihost)
 	spin_unlock_irq(&ihost->scic_lock);
 
 	wait_for_stop(ihost);
+
+	/* disable sgpio: where the above wait should give time for the
+	 * enclosure to sample the gpios going inactive
+	 */
+	writel(0, &ihost->scu_registers->peg0.sgpio.interface_control);
+
 	sci_controller_reset(ihost);
 
 	/* Cancel any/all outstanding port timers */
@@ -2365,6 +2375,12 @@ int isci_host_init(struct isci_host *ihost)
 	for (i = 0; i < SCI_MAX_PHYS; i++)
 		isci_phy_init(&ihost->phys[i], ihost, i);
 
+	/* enable sgpio */
+	writel(1, &ihost->scu_registers->peg0.sgpio.interface_control);
+	for (i = 0; i < isci_gpio_count(ihost); i++)
+		writel(SGPIO_HW_CONTROL, &ihost->scu_registers->peg0.sgpio.output_data_select[i]);
+	writel(0, &ihost->scu_registers->peg0.sgpio.vendor_specific_code);
+
 	for (i = 0; i < SCI_MAX_REMOTE_DEVICES; i++) {
 		struct isci_remote_device *idev = &ihost->devices[i];
 
@@ -2760,3 +2776,56 @@ enum sci_task_status sci_controller_start_task(struct isci_host *ihost,
 
 	return status;
 }
+
+static int sci_write_gpio_tx_gp(struct isci_host *ihost, u8 reg_index, u8 reg_count, u8 *write_data)
+{
+	int d;
+
+	/* no support for TX_GP_CFG */
+	if (reg_index == 0)
+		return -EINVAL;
+
+	for (d = 0; d < isci_gpio_count(ihost); d++) {
+		u32 val = 0x444; /* all ODx.n clear */
+		int i;
+
+		for (i = 0; i < 3; i++) {
+			int bit = (i << 2) + 2;
+
+			bit = try_test_sas_gpio_gp_bit(to_sas_gpio_od(d, i),
+						       write_data, reg_index,
+						       reg_count);
+			if (bit < 0)
+				break;
+
+			/* if od is set, clear the 'invert' bit */
+			val &= ~(bit << ((i << 2) + 2));
+		}
+
+		if (i < 3)
+			break;
+		writel(val, &ihost->scu_registers->peg0.sgpio.output_data_select[d]);
+	}
+
+	/* unless reg_index is > 1, we should always be able to write at
+	 * least one register
+	 */
+	return d > 0;
+}
+
+int isci_gpio_write(struct sas_ha_struct *sas_ha, u8 reg_type, u8 reg_index,
+		    u8 reg_count, u8 *write_data)
+{
+	struct isci_host *ihost = sas_ha->lldd_ha;
+	int written;
+
+	switch (reg_type) {
+	case SAS_GPIO_REG_TX_GP:
+		written = sci_write_gpio_tx_gp(ihost, reg_index, reg_count, write_data);
+		break;
+	default:
+		written = -EINVAL;
+	}
+
+	return written;
+}