diff options
| author | James Bottomley <JBottomley@Parallels.com> | 2013-05-07 21:44:06 (GMT) |
|---|---|---|
| committer | James Bottomley <JBottomley@Parallels.com> | 2013-05-10 14:47:52 (GMT) |
| commit | aa9f8328fc51460e15da129caf622b6560fa8c99 (patch) | |
| tree | 3ca4c2a29e94538acff4aae04214d5645eaeac02 /drivers/scsi/pm8001/pm80xx_hwi.c | |
| parent | a6cb3d012b983b350ae3892cff2e692665df0e1e (diff) | |
| download | linux-aa9f8328fc51460e15da129caf622b6560fa8c99.tar.xz | |
[SCSI] sas: unify the pointlessly separated enums sas_dev_type and sas_device_type
These enums have been separate since the dawn of SAS, mainly because the
latter is a procotol only enum and the former includes additional state
for libsas. The dichotomy causes endless confusion about which one you
should use where and leads to pointless warnings like this:
drivers/scsi/mvsas/mv_sas.c: In function 'mvs_update_phyinfo':
drivers/scsi/mvsas/mv_sas.c:1162:34: warning: comparison between 'enum sas_device_type' and 'enum sas_dev_type' [-Wenum-compare]
Fix by eliminating one of them. The one kept is effectively the sas.h
one, but call it sas_device_type and make sure the enums are all
properly namespaced with the SAS_ prefix.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Diffstat (limited to 'drivers/scsi/pm8001/pm80xx_hwi.c')
| -rw-r--r-- | drivers/scsi/pm8001/pm80xx_hwi.c | 12 |
1 files changed, 6 insertions, 6 deletions
diff --git a/drivers/scsi/pm8001/pm80xx_hwi.c b/drivers/scsi/pm8001/pm80xx_hwi.c index 670998a..302514d 100644 --- a/drivers/scsi/pm8001/pm80xx_hwi.c +++ b/drivers/scsi/pm8001/pm80xx_hwi.c @@ -2684,7 +2684,7 @@ hw_event_sata_phy_up(struct pm8001_hba_info *pm8001_ha, void *piomb) sizeof(struct dev_to_host_fis)); phy->frame_rcvd_size = sizeof(struct dev_to_host_fis); phy->identify.target_port_protocols = SAS_PROTOCOL_SATA; - phy->identify.device_type = SATA_DEV; + phy->identify.device_type = SAS_SATA_DEV; pm8001_get_attached_sas_addr(phy, phy->sas_phy.attached_sas_addr); spin_unlock_irqrestore(&phy->sas_phy.frame_rcvd_lock, flags); pm8001_bytes_dmaed(pm8001_ha, phy_id); @@ -3952,7 +3952,7 @@ pm80xx_chip_phy_start_req(struct pm8001_hba_info *pm8001_ha, u8 phy_id) Have to add "SAS PHY Analog Setup SPASTI 1 Byte" Based on need **/ - payload.sas_identify.dev_type = SAS_END_DEV; + payload.sas_identify.dev_type = SAS_END_DEVICE; payload.sas_identify.initiator_bits = SAS_PROTOCOL_ALL; memcpy(payload.sas_identify.sas_addr, pm8001_ha->sas_addr, SAS_ADDR_SIZE); @@ -4015,11 +4015,11 @@ static int pm80xx_chip_reg_dev_req(struct pm8001_hba_info *pm8001_ha, if (flag == 1) { stp_sspsmp_sata = 0x02; /*direct attached sata */ } else { - if (pm8001_dev->dev_type == SATA_DEV) + if (pm8001_dev->dev_type == SAS_SATA_DEV) stp_sspsmp_sata = 0x00; /* stp*/ - else if (pm8001_dev->dev_type == SAS_END_DEV || - pm8001_dev->dev_type == EDGE_DEV || - pm8001_dev->dev_type == FANOUT_DEV) + else if (pm8001_dev->dev_type == SAS_END_DEVICE || + pm8001_dev->dev_type == SAS_EDGE_EXPANDER_DEVICE || + pm8001_dev->dev_type == SAS_FANOUT_EXPANDER_DEVICE) stp_sspsmp_sata = 0x01; /*ssp or smp*/ } if (parent_dev && DEV_IS_EXPANDER(parent_dev->dev_type)) |