Merge tag 'usb-3.8-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb

Pull USB fixes from Greg Kroah-Hartman:
 "Here are a bunch of USB fixes for your 3.8-rc3 tree.  They all either
  fix problems that have been reported (like the xhci/hub changes) or
  add new device ids to existing drivers.

  Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"

* tag 'usb-3.8-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (39 commits)
  usb: ftdi_sio: Crucible Technologies COMET Caller ID - pid added
  usb: host: ohci-tmio: fix compile warning
  USB: Add device quirk for Microsoft VX700 webcam
  USB: ehci-fsl: fix regression on mpc5121e
  usb: chipidea: Allow disabling streaming not only in udc mode
  USB: fsl-mph-dr-of: fix regression on mpc5121e
  USB: select USB_ARCH_HAS_EHCI for MXS
  USB: hub: handle claim of enabled remote wakeup after reset
  USB: cdc-acm: Add support for "PSC Scanning, Magellan 800i"
  USB: option: add Nexpring NP10T terminal id
  USB: option: add Telekom Speedstick LTE II
  USB: option: blacklist network interface on ZTE MF880
  usb: imx21-hcd: Include missing linux/module.h
  USB: option: Add new MEDIATEK PID support
  USB: ehci: make debug port in-use detection functional again
  USB: usbtest: fix test number in log message
  xhci: Avoid "dead ports", add roothub port polling.
  USB: Handle warm reset failure on empty port.
  USB: Ignore port state until reset completes.
  USB: Increase reset timeout.
  ...

10 files changed, 90 insertions, 28 deletions

diff --git a/drivers/usb/host/ehci-fsl.c b/drivers/usb/host/ehci-fsl.c
index fd9b542..d81d2fc 100644
--- a/drivers/usb/host/ehci-fsl.c
+++ b/drivers/usb/host/ehci-fsl.c
@@ -230,7 +230,7 @@ static int ehci_fsl_setup_phy(struct usb_hcd *hcd,
 
 	switch (phy_mode) {
 	case FSL_USB2_PHY_ULPI:
-		if (pdata->controller_ver) {
+		if (pdata->have_sysif_regs && pdata->controller_ver) {
 			/* controller version 1.6 or above */
 			setbits32(non_ehci + FSL_SOC_USB_CTRL,
 					ULPI_PHY_CLK_SEL);
@@ -251,7 +251,7 @@ static int ehci_fsl_setup_phy(struct usb_hcd *hcd,
 		portsc |= PORT_PTS_PTW;
 		/* fall through */
 	case FSL_USB2_PHY_UTMI:
-		if (pdata->controller_ver) {
+		if (pdata->have_sysif_regs && pdata->controller_ver) {
 			/* controller version 1.6 or above */
 			setbits32(non_ehci + FSL_SOC_USB_CTRL, UTMI_PHY_EN);
 			mdelay(FSL_UTMI_PHY_DLY);  /* Delay for UTMI PHY CLK to
@@ -267,7 +267,8 @@ static int ehci_fsl_setup_phy(struct usb_hcd *hcd,
 		break;
 	}
 
-	if (pdata->controller_ver && (phy_mode == FSL_USB2_PHY_ULPI)) {
+	if (pdata->have_sysif_regs && pdata->controller_ver &&
+	    (phy_mode == FSL_USB2_PHY_ULPI)) {
 		/* check PHY_CLK_VALID to get phy clk valid */
 		if (!spin_event_timeout(in_be32(non_ehci + FSL_SOC_USB_CTRL) &
 				PHY_CLK_VALID, FSL_USB_PHY_CLK_TIMEOUT, 0)) {
@@ -278,7 +279,7 @@ static int ehci_fsl_setup_phy(struct usb_hcd *hcd,
 
 	ehci_writel(ehci, portsc, &ehci->regs->port_status[port_offset]);
 
-	if (phy_mode != FSL_USB2_PHY_ULPI)
+	if (phy_mode != FSL_USB2_PHY_ULPI && pdata->have_sysif_regs)
 		setbits32(non_ehci + FSL_SOC_USB_CTRL, USB_CTRL_USB_EN);
 
 	return 0;
diff --git a/drivers/usb/host/ehci-mv.c b/drivers/usb/host/ehci-mv.c
index f7bfc0b..6c56297 100644
--- a/drivers/usb/host/ehci-mv.c
+++ b/drivers/usb/host/ehci-mv.c
@@ -43,7 +43,7 @@ static void ehci_clock_enable(struct ehci_hcd_mv *ehci_mv)
 	unsigned int i;
 
 	for (i = 0; i < ehci_mv->clknum; i++)
-		clk_enable(ehci_mv->clk[i]);
+		clk_prepare_enable(ehci_mv->clk[i]);
 }
 
 static void ehci_clock_disable(struct ehci_hcd_mv *ehci_mv)
@@ -51,7 +51,7 @@ static void ehci_clock_disable(struct ehci_hcd_mv *ehci_mv)
 	unsigned int i;
 
 	for (i = 0; i < ehci_mv->clknum; i++)
-		clk_disable(ehci_mv->clk[i]);
+		clk_disable_unprepare(ehci_mv->clk[i]);
 }
 
 static int mv_ehci_enable(struct ehci_hcd_mv *ehci_mv)
diff --git a/drivers/usb/host/ehci-pci.c b/drivers/usb/host/ehci-pci.c
index dabb204..170b939 100644
--- a/drivers/usb/host/ehci-pci.c
+++ b/drivers/usb/host/ehci-pci.c
@@ -200,6 +200,26 @@ static int ehci_pci_setup(struct usb_hcd *hcd)
 		break;
 	}
 
+	/* optional debug port, normally in the first BAR */
+	temp = pci_find_capability(pdev, PCI_CAP_ID_DBG);
+	if (temp) {
+		pci_read_config_dword(pdev, temp, &temp);
+		temp >>= 16;
+		if (((temp >> 13) & 7) == 1) {
+			u32 hcs_params = ehci_readl(ehci,
+						    &ehci->caps->hcs_params);
+
+			temp &= 0x1fff;
+			ehci->debug = hcd->regs + temp;
+			temp = ehci_readl(ehci, &ehci->debug->control);
+			ehci_info(ehci, "debug port %d%s\n",
+				  HCS_DEBUG_PORT(hcs_params),
+				  (temp & DBGP_ENABLED) ? " IN USE" : "");
+			if (!(temp & DBGP_ENABLED))
+				ehci->debug = NULL;
+		}
+	}
+
 	retval = ehci_setup(hcd);
 	if (retval)
 		return retval;
@@ -228,25 +248,6 @@ static int ehci_pci_setup(struct usb_hcd *hcd)
 		break;
 	}
 
-	/* optional debug port, normally in the first BAR */
-	temp = pci_find_capability(pdev, 0x0a);
-	if (temp) {
-		pci_read_config_dword(pdev, temp, &temp);
-		temp >>= 16;
-		if ((temp & (3 << 13)) == (1 << 13)) {
-			temp &= 0x1fff;
-			ehci->debug = hcd->regs + temp;
-			temp = ehci_readl(ehci, &ehci->debug->control);
-			ehci_info(ehci, "debug port %d%s\n",
-				HCS_DEBUG_PORT(ehci->hcs_params),
-				(temp & DBGP_ENABLED)
-					? " IN USE"
-					: "");
-			if (!(temp & DBGP_ENABLED))
-				ehci->debug = NULL;
-		}
-	}
-
 	/* at least the Genesys GL880S needs fixup here */
 	temp = HCS_N_CC(ehci->hcs_params) * HCS_N_PCC(ehci->hcs_params);
 	temp &= 0x0f;
diff --git a/drivers/usb/host/fsl-mph-dr-of.c b/drivers/usb/host/fsl-mph-dr-of.c
index 5105127..11e0b79 100644
--- a/drivers/usb/host/fsl-mph-dr-of.c
+++ b/drivers/usb/host/fsl-mph-dr-of.c
@@ -142,6 +142,9 @@ static int usb_get_ver_info(struct device_node *np)
 			return ver;
 	}
 
+	if (of_device_is_compatible(np, "fsl,mpc5121-usb2-dr"))
+		return FSL_USB_VER_OLD;
+
 	if (of_device_is_compatible(np, "fsl-usb2-mph")) {
 		if (of_device_is_compatible(np, "fsl-usb2-mph-v1.6"))
 			ver = FSL_USB_VER_1_6;
diff --git a/drivers/usb/host/imx21-hcd.c b/drivers/usb/host/imx21-hcd.c
index bd6a744..f0ebe8e 100644
--- a/drivers/usb/host/imx21-hcd.c
+++ b/drivers/usb/host/imx21-hcd.c
@@ -58,6 +58,7 @@
 #include <linux/usb.h>
 #include <linux/usb/hcd.h>
 #include <linux/dma-mapping.h>
+#include <linux/module.h>
 
 #include "imx21-hcd.h"
 
diff --git a/drivers/usb/host/ohci-tmio.c b/drivers/usb/host/ohci-tmio.c
index d370245..5e3a6de 100644
--- a/drivers/usb/host/ohci-tmio.c
+++ b/drivers/usb/host/ohci-tmio.c
@@ -128,7 +128,8 @@ static void tmio_start_hc(struct platform_device *dev)
 	tmio_iowrite8(2, tmio->ccr + CCR_INTC);
 
 	dev_info(&dev->dev, "revision %d @ 0x%08llx, irq %d\n",
-			tmio_ioread8(tmio->ccr + CCR_REVID), hcd->rsrc_start, hcd->irq);
+			tmio_ioread8(tmio->ccr + CCR_REVID),
+			(u64) hcd->rsrc_start, hcd->irq);
 }
 
 static int ohci_tmio_start(struct usb_hcd *hcd)
diff --git a/drivers/usb/host/xhci-hub.c b/drivers/usb/host/xhci-hub.c
index a686cf4..6891442 100644
--- a/drivers/usb/host/xhci-hub.c
+++ b/drivers/usb/host/xhci-hub.c
@@ -761,12 +761,39 @@ int xhci_hub_control(struct usb_hcd *hcd, u16 typeReq, u16 wValue,
 			break;
 		case USB_PORT_FEAT_LINK_STATE:
 			temp = xhci_readl(xhci, port_array[wIndex]);
+
+			/* Disable port */
+			if (link_state == USB_SS_PORT_LS_SS_DISABLED) {
+				xhci_dbg(xhci, "Disable port %d\n", wIndex);
+				temp = xhci_port_state_to_neutral(temp);
+				/*
+				 * Clear all change bits, so that we get a new
+				 * connection event.
+				 */
+				temp |= PORT_CSC | PORT_PEC | PORT_WRC |
+					PORT_OCC | PORT_RC | PORT_PLC |
+					PORT_CEC;
+				xhci_writel(xhci, temp | PORT_PE,
+					port_array[wIndex]);
+				temp = xhci_readl(xhci, port_array[wIndex]);
+				break;
+			}
+
+			/* Put link in RxDetect (enable port) */
+			if (link_state == USB_SS_PORT_LS_RX_DETECT) {
+				xhci_dbg(xhci, "Enable port %d\n", wIndex);
+				xhci_set_link_state(xhci, port_array, wIndex,
+						link_state);
+				temp = xhci_readl(xhci, port_array[wIndex]);
+				break;
+			}
+
 			/* Software should not attempt to set
-			 * port link state above '5' (Rx.Detect) and the port
+			 * port link state above '3' (U3) and the port
 			 * must be enabled.
 			 */
 			if ((temp & PORT_PE) == 0 ||
-				(link_state > USB_SS_PORT_LS_RX_DETECT)) {
+				(link_state > USB_SS_PORT_LS_U3)) {
 				xhci_warn(xhci, "Cannot set link state.\n");
 				goto error;
 			}
@@ -957,6 +984,7 @@ int xhci_hub_status_data(struct usb_hcd *hcd, char *buf)
 	int max_ports;
 	__le32 __iomem **port_array;
 	struct xhci_bus_state *bus_state;
+	bool reset_change = false;
 
 	max_ports = xhci_get_ports(hcd, &port_array);
 	bus_state = &xhci->bus_state[hcd_index(hcd)];
@@ -988,6 +1016,12 @@ int xhci_hub_status_data(struct usb_hcd *hcd, char *buf)
 			buf[(i + 1) / 8] |= 1 << (i + 1) % 8;
 			status = 1;
 		}
+		if ((temp & PORT_RC))
+			reset_change = true;
+	}
+	if (!status && !reset_change) {
+		xhci_dbg(xhci, "%s: stopping port polling.\n", __func__);
+		clear_bit(HCD_FLAG_POLL_RH, &hcd->flags);
 	}
 	spin_unlock_irqrestore(&xhci->lock, flags);
 	return status ? retval : 0;
diff --git a/drivers/usb/host/xhci-mem.c b/drivers/usb/host/xhci-mem.c
index fb51c70..35616ff 100644
--- a/drivers/usb/host/xhci-mem.c
+++ b/drivers/usb/host/xhci-mem.c
@@ -1250,6 +1250,8 @@ static unsigned int xhci_microframes_to_exponent(struct usb_device *udev,
 static unsigned int xhci_parse_microframe_interval(struct usb_device *udev,
 		struct usb_host_endpoint *ep)
 {
+	if (ep->desc.bInterval == 0)
+		return 0;
 	return xhci_microframes_to_exponent(udev, ep,
 			ep->desc.bInterval, 0, 15);
 }
diff --git a/drivers/usb/host/xhci-ring.c b/drivers/usb/host/xhci-ring.c
index cbb44b7..59fb5c6 100644
--- a/drivers/usb/host/xhci-ring.c
+++ b/drivers/usb/host/xhci-ring.c
@@ -1725,6 +1725,15 @@ cleanup:
 	if (bogus_port_status)
 		return;
 
+	/*
+	 * xHCI port-status-change events occur when the "or" of all the
+	 * status-change bits in the portsc register changes from 0 to 1.
+	 * New status changes won't cause an event if any other change
+	 * bits are still set.  When an event occurs, switch over to
+	 * polling to avoid losing status changes.
+	 */
+	xhci_dbg(xhci, "%s: starting port polling.\n", __func__);
+	set_bit(HCD_FLAG_POLL_RH, &hcd->flags);
 	spin_unlock(&xhci->lock);
 	/* Pass this up to the core */
 	usb_hcd_poll_rh_status(hcd);
diff --git a/drivers/usb/host/xhci.c b/drivers/usb/host/xhci.c
index 5c72c43..f1f01a8 100644
--- a/drivers/usb/host/xhci.c
+++ b/drivers/usb/host/xhci.c
@@ -884,6 +884,11 @@ int xhci_suspend(struct xhci_hcd *xhci)
 			xhci->shared_hcd->state != HC_STATE_SUSPENDED)
 		return -EINVAL;
 
+	/* Don't poll the roothubs on bus suspend. */
+	xhci_dbg(xhci, "%s: stopping port polling.\n", __func__);
+	clear_bit(HCD_FLAG_POLL_RH, &hcd->flags);
+	del_timer_sync(&hcd->rh_timer);
+
 	spin_lock_irq(&xhci->lock);
 	clear_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags);
 	clear_bit(HCD_FLAG_HW_ACCESSIBLE, &xhci->shared_hcd->flags);
@@ -1069,6 +1074,11 @@ int xhci_resume(struct xhci_hcd *xhci, bool hibernated)
 	if (xhci->quirks & XHCI_COMP_MODE_QUIRK)
 		compliance_mode_recovery_timer_init(xhci);
 
+	/* Re-enable port polling. */
+	xhci_dbg(xhci, "%s: starting port polling.\n", __func__);
+	set_bit(HCD_FLAG_POLL_RH, &hcd->flags);
+	usb_hcd_poll_rh_status(hcd);
+
 	return retval;
 }
 #endif	/* CONFIG_PM */