Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem

Conflicts:
	drivers/net/ethernet/broadcom/Kconfig

6 files changed, 431 insertions, 46 deletions

diff --git a/include/linux/bcma/bcma.h b/include/linux/bcma/bcma.h
index 622fc50..4d043c3 100644
--- a/include/linux/bcma/bcma.h
+++ b/include/linux/bcma/bcma.h
@@ -72,7 +72,19 @@ struct bcma_host_ops {
 /* Core-ID values. */
 #define BCMA_CORE_OOB_ROUTER		0x367	/* Out of band */
 #define BCMA_CORE_4706_CHIPCOMMON	0x500
+#define BCMA_CORE_PCIEG2		0x501
+#define BCMA_CORE_DMA			0x502
+#define BCMA_CORE_SDIO3			0x503
+#define BCMA_CORE_USB20			0x504
+#define BCMA_CORE_USB30			0x505
+#define BCMA_CORE_A9JTAG		0x506
+#define BCMA_CORE_DDR23			0x507
+#define BCMA_CORE_ROM			0x508
+#define BCMA_CORE_NAND			0x509
+#define BCMA_CORE_QSPI			0x50A
+#define BCMA_CORE_CHIPCOMMON_B		0x50B
 #define BCMA_CORE_4706_SOC_RAM		0x50E
+#define BCMA_CORE_ARMCA9		0x510
 #define BCMA_CORE_4706_MAC_GBIT		0x52D
 #define BCMA_CORE_AMEMC			0x52E	/* DDR1/2 memory controller core */
 #define BCMA_CORE_ALTA			0x534	/* I2S core */
@@ -177,6 +189,11 @@ struct bcma_host_ops {
 #define  BCMA_PKG_ID_BCM5357	11
 #define BCMA_CHIP_ID_BCM53572	53572
 #define  BCMA_PKG_ID_BCM47188	9
+#define BCMA_CHIP_ID_BCM4707	53010
+#define  BCMA_PKG_ID_BCM4707	1
+#define  BCMA_PKG_ID_BCM4708	2
+#define  BCMA_PKG_ID_BCM4709	0
+#define BCMA_CHIP_ID_BCM53018	53018
 
 /* Board types (on PCI usually equals to the subsystem dev id) */
 /* BCM4313 */
diff --git a/include/linux/ieee80211.h b/include/linux/ieee80211.h
index 4e101af..8def09e 100644
--- a/include/linux/ieee80211.h
+++ b/include/linux/ieee80211.h
@@ -1710,6 +1710,10 @@ enum ieee80211_eid {
 	WLAN_EID_OPMODE_NOTIF = 199,
 	WLAN_EID_WIDE_BW_CHANNEL_SWITCH = 194,
 	WLAN_EID_CHANNEL_SWITCH_WRAPPER = 196,
+	WLAN_EID_EXTENDED_BSS_LOAD = 193,
+	WLAN_EID_VHT_TX_POWER_ENVELOPE = 195,
+	WLAN_EID_AID = 197,
+	WLAN_EID_QUIET_CHANNEL = 198,
 
 	/* 802.11ad */
 	WLAN_EID_NON_TX_BSSID_CAP =  83,
@@ -1861,6 +1865,11 @@ enum ieee80211_tdls_actioncode {
 	WLAN_TDLS_DISCOVERY_REQUEST = 10,
 };
 
+/* Interworking capabilities are set in 7th bit of 4th byte of the
+ * @WLAN_EID_EXT_CAPABILITY information element
+ */
+#define WLAN_EXT_CAPA4_INTERWORKING_ENABLED	BIT(7)
+
 /*
  * TDLS capabililites to be enabled in the 5th byte of the
  * @WLAN_EID_EXT_CAPABILITY information element
diff --git a/include/net/cfg80211.h b/include/net/cfg80211.h
index f49de28..635e396 100644
--- a/include/net/cfg80211.h
+++ b/include/net/cfg80211.h
@@ -461,6 +461,33 @@ ieee80211_chandef_rate_flags(struct cfg80211_chan_def *chandef)
 }
 
 /**
+ * ieee80211_chandef_max_power - maximum transmission power for the chandef
+ *
+ * In some regulations, the transmit power may depend on the configured channel
+ * bandwidth which may be defined as dBm/MHz. This function returns the actual
+ * max_power for non-standard (20 MHz) channels.
+ *
+ * @chandef: channel definition for the channel
+ *
+ * Returns: maximum allowed transmission power in dBm for the chandef
+ */
+static inline int
+ieee80211_chandef_max_power(struct cfg80211_chan_def *chandef)
+{
+	switch (chandef->width) {
+	case NL80211_CHAN_WIDTH_5:
+		return min(chandef->chan->max_reg_power - 6,
+			   chandef->chan->max_power);
+	case NL80211_CHAN_WIDTH_10:
+		return min(chandef->chan->max_reg_power - 3,
+			   chandef->chan->max_power);
+	default:
+		break;
+	}
+	return chandef->chan->max_power;
+}
+
+/**
  * enum survey_info_flags - survey information flags
  *
  * @SURVEY_INFO_NOISE_DBM: noise (in dBm) was filled in
@@ -490,7 +517,7 @@ enum survey_info_flags {
  * @channel: the channel this survey record reports, mandatory
  * @filled: bitflag of flags from &enum survey_info_flags
  * @noise: channel noise in dBm. This and all following fields are
- *     optional
+ *	optional
  * @channel_time: amount of time in ms the radio spent on the channel
  * @channel_time_busy: amount of time the primary channel was sensed busy
  * @channel_time_ext_busy: amount of time the extension channel was sensed busy
@@ -546,9 +573,9 @@ struct cfg80211_crypto_settings {
 /**
  * struct cfg80211_beacon_data - beacon data
  * @head: head portion of beacon (before TIM IE)
- *     or %NULL if not changed
+ *	or %NULL if not changed
  * @tail: tail portion of beacon (after TIM IE)
- *     or %NULL if not changed
+ *	or %NULL if not changed
  * @head_len: length of @head
  * @tail_len: length of @tail
  * @beacon_ies: extra information element(s) to add into Beacon frames or %NULL
@@ -639,6 +666,30 @@ struct cfg80211_ap_settings {
 };
 
 /**
+ * struct cfg80211_csa_settings - channel switch settings
+ *
+ * Used for channel switch
+ *
+ * @chandef: defines the channel to use after the switch
+ * @beacon_csa: beacon data while performing the switch
+ * @counter_offset_beacon: offset for the counter within the beacon (tail)
+ * @counter_offset_presp: offset for the counter within the probe response
+ * @beacon_after: beacon data to be used on the new channel
+ * @radar_required: whether radar detection is required on the new channel
+ * @block_tx: whether transmissions should be blocked while changing
+ * @count: number of beacons until switch
+ */
+struct cfg80211_csa_settings {
+	struct cfg80211_chan_def chandef;
+	struct cfg80211_beacon_data beacon_csa;
+	u16 counter_offset_beacon, counter_offset_presp;
+	struct cfg80211_beacon_data beacon_after;
+	bool radar_required;
+	bool block_tx;
+	u8 count;
+};
+
+/**
  * enum station_parameters_apply_mask - station parameter values to apply
  * @STATION_PARAM_APPLY_UAPSD: apply new uAPSD parameters (uapsd_queues, max_sp)
  * @STATION_PARAM_APPLY_CAPABILITY: apply new capability
@@ -764,7 +815,7 @@ int cfg80211_check_station_change(struct wiphy *wiphy,
  * @STATION_INFO_PLINK_STATE: @plink_state filled
  * @STATION_INFO_SIGNAL: @signal filled
  * @STATION_INFO_TX_BITRATE: @txrate fields are filled
- *  (tx_bitrate, tx_bitrate_flags and tx_bitrate_mcs)
+ *	(tx_bitrate, tx_bitrate_flags and tx_bitrate_mcs)
  * @STATION_INFO_RX_PACKETS: @rx_packets filled with 32-bit value
  * @STATION_INFO_TX_PACKETS: @tx_packets filled with 32-bit value
  * @STATION_INFO_TX_RETRIES: @tx_retries filled
@@ -1285,6 +1336,7 @@ struct cfg80211_ssid {
  * @n_ssids: number of SSIDs
  * @channels: channels to scan on.
  * @n_channels: total number of channels to scan
+ * @scan_width: channel width for scanning
  * @ie: optional information element(s) to add into Probe Request or %NULL
  * @ie_len: length of ie in octets
  * @flags: bit field of flags controlling operation
@@ -1300,6 +1352,7 @@ struct cfg80211_scan_request {
 	struct cfg80211_ssid *ssids;
 	int n_ssids;
 	u32 n_channels;
+	enum nl80211_bss_scan_width scan_width;
 	const u8 *ie;
 	size_t ie_len;
 	u32 flags;
@@ -1333,6 +1386,7 @@ struct cfg80211_match_set {
  * @ssids: SSIDs to scan for (passed in the probe_reqs in active scans)
  * @n_ssids: number of SSIDs
  * @n_channels: total number of channels to scan
+ * @scan_width: channel width for scanning
  * @interval: interval between each scheduled scan cycle
  * @ie: optional information element(s) to add into Probe Request or %NULL
  * @ie_len: length of ie in octets
@@ -1352,6 +1406,7 @@ struct cfg80211_sched_scan_request {
 	struct cfg80211_ssid *ssids;
 	int n_ssids;
 	u32 n_channels;
+	enum nl80211_bss_scan_width scan_width;
 	u32 interval;
 	const u8 *ie;
 	size_t ie_len;
@@ -1403,6 +1458,7 @@ struct cfg80211_bss_ies {
  * for use in scan results and similar.
  *
  * @channel: channel this BSS is on
+ * @scan_width: width of the control channel
  * @bssid: BSSID of the BSS
  * @beacon_interval: the beacon interval as from the frame
  * @capability: the capability field in host byte order
@@ -1424,6 +1480,7 @@ struct cfg80211_bss_ies {
  */
 struct cfg80211_bss {
 	struct ieee80211_channel *channel;
+	enum nl80211_bss_scan_width scan_width;
 
 	const struct cfg80211_bss_ies __rcu *ies;
 	const struct cfg80211_bss_ies __rcu *beacon_ies;
@@ -1509,7 +1566,7 @@ enum cfg80211_assoc_req_flags {
  * @prev_bssid: previous BSSID, if not %NULL use reassociate frame
  * @flags:  See &enum cfg80211_assoc_req_flags
  * @ht_capa:  HT Capabilities over-rides.  Values set in ht_capa_mask
- *   will be used in ht_capa.  Un-supported values will be ignored.
+ *	will be used in ht_capa.  Un-supported values will be ignored.
  * @ht_capa_mask:  The bits of ht_capa which are to be used.
  * @vht_capa: VHT capability override
  * @vht_capa_mask: VHT capability mask indicating which fields to use
@@ -1592,6 +1649,9 @@ struct cfg80211_disassoc_request {
  *	user space. Otherwise, port is marked authorized by default.
  * @basic_rates: bitmap of basic rates to use when creating the IBSS
  * @mcast_rate: per-band multicast rate index + 1 (0: disabled)
+ * @ht_capa:  HT Capabilities over-rides.  Values set in ht_capa_mask
+ *	will be used in ht_capa.  Un-supported values will be ignored.
+ * @ht_capa_mask:  The bits of ht_capa which are to be used.
  */
 struct cfg80211_ibss_params {
 	u8 *ssid;
@@ -1605,6 +1665,8 @@ struct cfg80211_ibss_params {
 	bool privacy;
 	bool control_port;
 	int mcast_rate[IEEE80211_NUM_BANDS];
+	struct ieee80211_ht_cap ht_capa;
+	struct ieee80211_ht_cap ht_capa_mask;
 };
 
 /**
@@ -1630,9 +1692,9 @@ struct cfg80211_ibss_params {
  * @key: WEP key for shared key authentication
  * @flags:  See &enum cfg80211_assoc_req_flags
  * @bg_scan_period:  Background scan period in seconds
- *   or -1 to indicate that default value is to be used.
+ *	or -1 to indicate that default value is to be used.
  * @ht_capa:  HT Capabilities over-rides.  Values set in ht_capa_mask
- *   will be used in ht_capa.  Un-supported values will be ignored.
+ *	will be used in ht_capa.  Un-supported values will be ignored.
  * @ht_capa_mask:  The bits of ht_capa which are to be used.
  * @vht_capa:  VHT Capability overrides
  * @vht_capa_mask: The bits of vht_capa which are to be used.
@@ -1698,7 +1760,7 @@ struct cfg80211_pmksa {
 };
 
 /**
- * struct cfg80211_wowlan_trig_pkt_pattern - packet pattern
+ * struct cfg80211_pkt_pattern - packet pattern
  * @mask: bitmask where to match pattern and where to ignore bytes,
  *	one bit per byte, in same format as nl80211
  * @pattern: bytes to match where bitmask is 1
@@ -1708,7 +1770,7 @@ struct cfg80211_pmksa {
  * Internal note: @mask and @pattern are allocated in one chunk of
  * memory, free @mask only!
  */
-struct cfg80211_wowlan_trig_pkt_pattern {
+struct cfg80211_pkt_pattern {
 	u8 *mask, *pattern;
 	int pattern_len;
 	int pkt_offset;
@@ -1770,12 +1832,41 @@ struct cfg80211_wowlan {
 	bool any, disconnect, magic_pkt, gtk_rekey_failure,
 	     eap_identity_req, four_way_handshake,
 	     rfkill_release;
-	struct cfg80211_wowlan_trig_pkt_pattern *patterns;
+	struct cfg80211_pkt_pattern *patterns;
 	struct cfg80211_wowlan_tcp *tcp;
 	int n_patterns;
 };
 
 /**
+ * struct cfg80211_coalesce_rules - Coalesce rule parameters
+ *
+ * This structure defines coalesce rule for the device.
+ * @delay: maximum coalescing delay in msecs.
+ * @condition: condition for packet coalescence.
+ *	see &enum nl80211_coalesce_condition.
+ * @patterns: array of packet patterns
+ * @n_patterns: number of patterns
+ */
+struct cfg80211_coalesce_rules {
+	int delay;
+	enum nl80211_coalesce_condition condition;
+	struct cfg80211_pkt_pattern *patterns;
+	int n_patterns;
+};
+
+/**
+ * struct cfg80211_coalesce - Packet coalescing settings
+ *
+ * This structure defines coalescing settings.
+ * @rules: array of coalesce rules
+ * @n_rules: number of rules
+ */
+struct cfg80211_coalesce {
+	struct cfg80211_coalesce_rules *rules;
+	int n_rules;
+};
+
+/**
  * struct cfg80211_wowlan_wakeup - wakeup report
  * @disconnect: woke up by getting disconnected
  * @magic_pkt: woke up by receiving magic packet
@@ -2071,6 +2162,9 @@ struct cfg80211_update_ft_ies_params {
  *	driver can take the most appropriate actions.
  * @crit_proto_stop: Indicates critical protocol no longer needs increased link
  *	reliability. This operation can not fail.
+ * @set_coalesce: Set coalesce parameters.
+ *
+ * @channel_switch: initiate channel-switch procedure (with CSA)
  */
 struct cfg80211_ops {
 	int	(*suspend)(struct wiphy *wiphy, struct cfg80211_wowlan *wow);
@@ -2306,6 +2400,12 @@ struct cfg80211_ops {
 				    u16 duration);
 	void	(*crit_proto_stop)(struct wiphy *wiphy,
 				   struct wireless_dev *wdev);
+	int	(*set_coalesce)(struct wiphy *wiphy,
+				struct cfg80211_coalesce *coalesce);
+
+	int	(*channel_switch)(struct wiphy *wiphy,
+				  struct net_device *dev,
+				  struct cfg80211_csa_settings *params);
 };
 
 /*
@@ -2371,6 +2471,8 @@ struct cfg80211_ops {
  * @WIPHY_FLAG_OFFCHAN_TX: Device supports direct off-channel TX.
  * @WIPHY_FLAG_HAS_REMAIN_ON_CHANNEL: Device supports remain-on-channel call.
  * @WIPHY_FLAG_SUPPORTS_5_10_MHZ: Device supports 5 MHz and 10 MHz channels.
+ * @WIPHY_FLAG_HAS_CHANNEL_SWITCH: Device supports channel switch in
+ *	beaconing mode (AP, IBSS, Mesh, ...).
  */
 enum wiphy_flags {
 	WIPHY_FLAG_CUSTOM_REGULATORY		= BIT(0),
@@ -2395,6 +2497,7 @@ enum wiphy_flags {
 	WIPHY_FLAG_OFFCHAN_TX			= BIT(20),
 	WIPHY_FLAG_HAS_REMAIN_ON_CHANNEL	= BIT(21),
 	WIPHY_FLAG_SUPPORTS_5_10_MHZ		= BIT(22),
+	WIPHY_FLAG_HAS_CHANNEL_SWITCH		= BIT(23),
 };
 
 /**
@@ -2532,6 +2635,25 @@ struct wiphy_wowlan_support {
 };
 
 /**
+ * struct wiphy_coalesce_support - coalesce support data
+ * @n_rules: maximum number of coalesce rules
+ * @max_delay: maximum supported coalescing delay in msecs
+ * @n_patterns: number of supported patterns in a rule
+ *	(see nl80211.h for the pattern definition)
+ * @pattern_max_len: maximum length of each pattern
+ * @pattern_min_len: minimum length of each pattern
+ * @max_pkt_offset: maximum Rx packet offset
+ */
+struct wiphy_coalesce_support {
+	int n_rules;
+	int max_delay;
+	int n_patterns;
+	int pattern_max_len;
+	int pattern_min_len;
+	int max_pkt_offset;
+};
+
+/**
  * struct wiphy - wireless hardware description
  * @reg_notifier: the driver's regulatory notification callback,
  *	note that if your driver uses wiphy_apply_custom_regulatory()
@@ -2641,6 +2763,7 @@ struct wiphy_wowlan_support {
  *	802.11-2012 8.4.2.29 for the defined fields.
  * @extended_capabilities_mask: mask of the valid values
  * @extended_capabilities_len: length of the extended capabilities
+ * @coalesce: packet coalescing support information
  */
 struct wiphy {
 	/* assign these fields before you register the wiphy */
@@ -2750,6 +2873,8 @@ struct wiphy {
 	const struct iw_handler_def *wext;
 #endif
 
+	const struct wiphy_coalesce_support *coalesce;
+
 	char priv[0] __aligned(NETDEV_ALIGN);
 };
 
@@ -3063,11 +3188,13 @@ ieee80211_get_response_rate(struct ieee80211_supported_band *sband,
 /**
  * ieee80211_mandatory_rates - get mandatory rates for a given band
  * @sband: the band to look for rates in
+ * @scan_width: width of the control channel
  *
  * This function returns a bitmap of the mandatory rates for the given
  * band, bits are set according to the rate position in the bitrates array.
  */
-u32 ieee80211_mandatory_rates(struct ieee80211_supported_band *sband);
+u32 ieee80211_mandatory_rates(struct ieee80211_supported_band *sband,
+			      enum nl80211_bss_scan_width scan_width);
 
 /*
  * Radiotap parsing functions -- for controlled injection support
@@ -3379,10 +3506,11 @@ void cfg80211_sched_scan_results(struct wiphy *wiphy);
 void cfg80211_sched_scan_stopped(struct wiphy *wiphy);
 
 /**
- * cfg80211_inform_bss_frame - inform cfg80211 of a received BSS frame
+ * cfg80211_inform_bss_width_frame - inform cfg80211 of a received BSS frame
  *
  * @wiphy: the wiphy reporting the BSS
  * @channel: The channel the frame was received on
+ * @scan_width: width of the control channel
  * @mgmt: the management frame (probe response or beacon)
  * @len: length of the management frame
  * @signal: the signal strength, type depends on the wiphy's signal_type
@@ -3395,16 +3523,29 @@ void cfg80211_sched_scan_stopped(struct wiphy *wiphy);
  * Or %NULL on error.
  */
 struct cfg80211_bss * __must_check
+cfg80211_inform_bss_width_frame(struct wiphy *wiphy,
+				struct ieee80211_channel *channel,
+				enum nl80211_bss_scan_width scan_width,
+				struct ieee80211_mgmt *mgmt, size_t len,
+				s32 signal, gfp_t gfp);
+
+static inline struct cfg80211_bss * __must_check
 cfg80211_inform_bss_frame(struct wiphy *wiphy,
 			  struct ieee80211_channel *channel,
 			  struct ieee80211_mgmt *mgmt, size_t len,
-			  s32 signal, gfp_t gfp);
+			  s32 signal, gfp_t gfp)
+{
+	return cfg80211_inform_bss_width_frame(wiphy, channel,
+					       NL80211_BSS_CHAN_WIDTH_20,
+					       mgmt, len, signal, gfp);
+}
 
 /**
  * cfg80211_inform_bss - inform cfg80211 of a new BSS
  *
  * @wiphy: the wiphy reporting the BSS
  * @channel: The channel the frame was received on
+ * @scan_width: width of the control channel
  * @bssid: the BSSID of the BSS
  * @tsf: the TSF sent by the peer in the beacon/probe response (or 0)
  * @capability: the capability field sent by the peer
@@ -3421,11 +3562,26 @@ cfg80211_inform_bss_frame(struct wiphy *wiphy,
  * Or %NULL on error.
  */
 struct cfg80211_bss * __must_check
+cfg80211_inform_bss_width(struct wiphy *wiphy,
+			  struct ieee80211_channel *channel,
+			  enum nl80211_bss_scan_width scan_width,
+			  const u8 *bssid, u64 tsf, u16 capability,
+			  u16 beacon_interval, const u8 *ie, size_t ielen,
+			  s32 signal, gfp_t gfp);
+
+static inline struct cfg80211_bss * __must_check
 cfg80211_inform_bss(struct wiphy *wiphy,
 		    struct ieee80211_channel *channel,
 		    const u8 *bssid, u64 tsf, u16 capability,
 		    u16 beacon_interval, const u8 *ie, size_t ielen,
-		    s32 signal, gfp_t gfp);
+		    s32 signal, gfp_t gfp)
+{
+	return cfg80211_inform_bss_width(wiphy, channel,
+					 NL80211_BSS_CHAN_WIDTH_20,
+					 bssid, tsf, capability,
+					 beacon_interval, ie, ielen, signal,
+					 gfp);
+}
 
 struct cfg80211_bss *cfg80211_get_bss(struct wiphy *wiphy,
 				      struct ieee80211_channel *channel,
@@ -3471,6 +3627,19 @@ void cfg80211_put_bss(struct wiphy *wiphy, struct cfg80211_bss *bss);
  */
 void cfg80211_unlink_bss(struct wiphy *wiphy, struct cfg80211_bss *bss);
 
+static inline enum nl80211_bss_scan_width
+cfg80211_chandef_to_scan_width(const struct cfg80211_chan_def *chandef)
+{
+	switch (chandef->width) {
+	case NL80211_CHAN_WIDTH_5:
+		return NL80211_BSS_CHAN_WIDTH_5;
+	case NL80211_CHAN_WIDTH_10:
+		return NL80211_BSS_CHAN_WIDTH_10;
+	default:
+		return NL80211_BSS_CHAN_WIDTH_20;
+	}
+}
+
 /**
  * cfg80211_rx_mlme_mgmt - notification of processed MLME management frame
  * @dev: network device
diff --git a/include/net/ieee80211_radiotap.h b/include/net/ieee80211_radiotap.h
index c6d07cb..8b5b714 100644
--- a/include/net/ieee80211_radiotap.h
+++ b/include/net/ieee80211_radiotap.h
@@ -230,6 +230,10 @@ enum ieee80211_radiotap_type {
 #define	IEEE80211_CHAN_PASSIVE	0x0200	/* Only passive scan allowed */
 #define	IEEE80211_CHAN_DYN	0x0400	/* Dynamic CCK-OFDM channel */
 #define	IEEE80211_CHAN_GFSK	0x0800	/* GFSK channel (FHSS PHY) */
+#define	IEEE80211_CHAN_GSM	0x1000	/* GSM (900 MHz) */
+#define	IEEE80211_CHAN_STURBO	0x2000	/* Static Turbo */
+#define	IEEE80211_CHAN_HALF	0x4000	/* Half channel (10 MHz wide) */
+#define	IEEE80211_CHAN_QUARTER	0x8000	/* Quarter channel (5 MHz wide) */
 
 /* For IEEE80211_RADIOTAP_FLAGS */
 #define	IEEE80211_RADIOTAP_F_CFP	0x01	/* sent/received
diff --git a/include/net/mac80211.h b/include/net/mac80211.h
index e5f0290..ab94dbc 100644
--- a/include/net/mac80211.h
+++ b/include/net/mac80211.h
@@ -152,11 +152,14 @@ struct ieee80211_low_level_stats {
  * @IEEE80211_CHANCTX_CHANGE_WIDTH: The channel width changed
  * @IEEE80211_CHANCTX_CHANGE_RX_CHAINS: The number of RX chains changed
  * @IEEE80211_CHANCTX_CHANGE_RADAR: radar detection flag changed
+ * @IEEE80211_CHANCTX_CHANGE_CHANNEL: switched to another operating channel,
+ *	this is used only with channel switching with CSA
  */
 enum ieee80211_chanctx_change {
 	IEEE80211_CHANCTX_CHANGE_WIDTH		= BIT(0),
 	IEEE80211_CHANCTX_CHANGE_RX_CHAINS	= BIT(1),
 	IEEE80211_CHANCTX_CHANGE_RADAR		= BIT(2),
+	IEEE80211_CHANCTX_CHANGE_CHANNEL	= BIT(3),
 };
 
 /**
@@ -811,6 +814,8 @@ ieee80211_tx_info_clear_status(struct ieee80211_tx_info *info)
  * @RX_FLAG_AMPDU_DELIM_CRC_KNOWN: The delimiter CRC field is known (the CRC
  *	is stored in the @ampdu_delimiter_crc field)
  * @RX_FLAG_STBC_MASK: STBC 2 bit bitmask. 1 - Nss=1, 2 - Nss=2, 3 - Nss=3
+ * @RX_FLAG_10MHZ: 10 MHz (half channel) was used
+ * @RX_FLAG_5MHZ: 5 MHz (quarter channel) was used
  */
 enum mac80211_rx_flags {
 	RX_FLAG_MMIC_ERROR		= BIT(0),
@@ -839,6 +844,8 @@ enum mac80211_rx_flags {
 	RX_FLAG_80P80MHZ		= BIT(24),
 	RX_FLAG_160MHZ			= BIT(25),
 	RX_FLAG_STBC_MASK		= BIT(26) | BIT(27),
+	RX_FLAG_10MHZ			= BIT(28),
+	RX_FLAG_5MHZ			= BIT(29),
 };
 
 #define RX_FLAG_STBC_SHIFT		26
@@ -1004,11 +1011,11 @@ enum ieee80211_smps_mode {
  * @radar_enabled: whether radar detection is enabled
  *
  * @long_frame_max_tx_count: Maximum number of transmissions for a "long" frame
- *    (a frame not RTS protected), called "dot11LongRetryLimit" in 802.11,
- *    but actually means the number of transmissions not the number of retries
+ *	(a frame not RTS protected), called "dot11LongRetryLimit" in 802.11,
+ *	but actually means the number of transmissions not the number of retries
  * @short_frame_max_tx_count: Maximum number of transmissions for a "short"
- *    frame, called "dot11ShortRetryLimit" in 802.11, but actually means the
- *    number of transmissions not the number of retries
+ *	frame, called "dot11ShortRetryLimit" in 802.11, but actually means the
+ *	number of transmissions not the number of retries
  *
  * @smps_mode: spatial multiplexing powersave mode; note that
  *	%IEEE80211_SMPS_STATIC is used when the device is not
@@ -1080,6 +1087,7 @@ enum ieee80211_vif_flags {
  * @addr: address of this interface
  * @p2p: indicates whether this AP or STA interface is a p2p
  *	interface, i.e. a GO or p2p-sta respectively
+ * @csa_active: marks whether a channel switch is going on
  * @driver_flags: flags/capabilities the driver has for this interface,
  *	these need to be set (or cleared) when the interface is added
  *	or, if supported by the driver, the interface type is changed
@@ -1092,7 +1100,7 @@ enum ieee80211_vif_flags {
  *	be off when it is %NULL there can still be races and packets could be
  *	processed after it switches back to %NULL.
  * @debugfs_dir: debugfs dentry, can be used by drivers to create own per
- *      interface debug files. Note that it will be NULL for the virtual
+ *	interface debug files. Note that it will be NULL for the virtual
  *	monitor interface (if that is requested.)
  * @drv_priv: data area for driver use, will always be aligned to
  *	sizeof(void *).
@@ -1102,6 +1110,7 @@ struct ieee80211_vif {
 	struct ieee80211_bss_conf bss_conf;
 	u8 addr[ETH_ALEN];
 	bool p2p;
+	bool csa_active;
 
 	u8 cab_queue;
 	u8 hw_queue[IEEE80211_NUM_ACS];
@@ -1425,10 +1434,10 @@ struct ieee80211_tx_control {
  *	the stack.
  *
  * @IEEE80211_HW_CONNECTION_MONITOR:
- *      The hardware performs its own connection monitoring, including
- *      periodic keep-alives to the AP and probing the AP on beacon loss.
- *      When this flag is set, signaling beacon-loss will cause an immediate
- *      change to disassociated state.
+ *	The hardware performs its own connection monitoring, including
+ *	periodic keep-alives to the AP and probing the AP on beacon loss.
+ *	When this flag is set, signaling beacon-loss will cause an immediate
+ *	change to disassociated state.
  *
  * @IEEE80211_HW_NEED_DTIM_BEFORE_ASSOC:
  *	This device needs to get data from beacon before association (i.e.
@@ -1526,10 +1535,10 @@ enum ieee80211_hw_flags {
  * @channel_change_time: time (in microseconds) it takes to change channels.
  *
  * @max_signal: Maximum value for signal (rssi) in RX information, used
- *     only when @IEEE80211_HW_SIGNAL_UNSPEC or @IEEE80211_HW_SIGNAL_DB
+ *	only when @IEEE80211_HW_SIGNAL_UNSPEC or @IEEE80211_HW_SIGNAL_DB
  *
  * @max_listen_interval: max listen interval in units of beacon interval
- *     that HW supports
+ *	that HW supports
  *
  * @queues: number of available hardware transmit queues for
  *	data packets. WMM/QoS requires at least four, these
@@ -2443,7 +2452,7 @@ enum ieee80211_roc_type {
  *	The callback can sleep.
  *
  * @set_tsf: Set the TSF timer to the specified value in the firmware/hardware.
- *      Currently, this is only used for IBSS mode debugging. Is not a
+ *	Currently, this is only used for IBSS mode debugging. Is not a
  *	required function.
  *	The callback can sleep.
  *
@@ -2633,6 +2642,16 @@ enum ieee80211_roc_type {
  * @ipv6_addr_change: IPv6 address assignment on the given interface changed.
  *	Currently, this is only called for managed or P2P client interfaces.
  *	This callback is optional; it must not sleep.
+ *
+ * @channel_switch_beacon: Starts a channel switch to a new channel.
+ *	Beacons are modified to include CSA or ECSA IEs before calling this
+ *	function. The corresponding count fields in these IEs must be
+ *	decremented, and when they reach zero the driver must call
+ *	ieee80211_csa_finish(). Drivers which use ieee80211_beacon_get()
+ *	get the csa counter decremented by mac80211, but must check if it is
+ *	zero using ieee80211_csa_is_complete() after the beacon has been
+ *	transmitted and then call ieee80211_csa_finish().
+ *
  */
 struct ieee80211_ops {
 	void (*tx)(struct ieee80211_hw *hw,
@@ -2820,6 +2839,9 @@ struct ieee80211_ops {
 				 struct ieee80211_vif *vif,
 				 struct inet6_dev *idev);
 #endif
+	void (*channel_switch_beacon)(struct ieee80211_hw *hw,
+				      struct ieee80211_vif *vif,
+				      struct cfg80211_chan_def *chandef);
 };
 
 /**
@@ -3315,6 +3337,25 @@ static inline struct sk_buff *ieee80211_beacon_get(struct ieee80211_hw *hw,
 }
 
 /**
+ * ieee80211_csa_finish - notify mac80211 about channel switch
+ * @vif: &struct ieee80211_vif pointer from the add_interface callback.
+ *
+ * After a channel switch announcement was scheduled and the counter in this
+ * announcement hit zero, this function must be called by the driver to
+ * notify mac80211 that the channel can be changed.
+ */
+void ieee80211_csa_finish(struct ieee80211_vif *vif);
+
+/**
+ * ieee80211_csa_is_complete - find out if counters reached zero
+ * @vif: &struct ieee80211_vif pointer from the add_interface callback.
+ *
+ * This function returns whether the channel switch counters reached zero.
+ */
+bool ieee80211_csa_is_complete(struct ieee80211_vif *vif);
+
+
+/**
  * ieee80211_proberesp_get - retrieve a Probe Response template
  * @hw: pointer obtained from ieee80211_alloc_hw().
  * @vif: &struct ieee80211_vif pointer from the add_interface callback.
@@ -4204,8 +4245,10 @@ struct rate_control_ops {
 
 	void *(*alloc_sta)(void *priv, struct ieee80211_sta *sta, gfp_t gfp);
 	void (*rate_init)(void *priv, struct ieee80211_supported_band *sband,
+			  struct cfg80211_chan_def *chandef,
 			  struct ieee80211_sta *sta, void *priv_sta);
 	void (*rate_update)(void *priv, struct ieee80211_supported_band *sband,
+			    struct cfg80211_chan_def *chandef,
 			    struct ieee80211_sta *sta, void *priv_sta,
 			    u32 changed);
 	void (*free_sta)(void *priv, struct ieee80211_sta *sta,
diff --git a/include/uapi/linux/nl80211.h b/include/uapi/linux/nl80211.h
index 861e5eb..1f42bc3 100644
--- a/include/uapi/linux/nl80211.h
+++ b/include/uapi/linux/nl80211.h
@@ -126,6 +126,31 @@
  */
 
 /**
+ * DOC: packet coalesce support
+ *
+ * In most cases, host that receives IPv4 and IPv6 multicast/broadcast
+ * packets does not do anything with these packets. Therefore the
+ * reception of these unwanted packets causes unnecessary processing
+ * and power consumption.
+ *
+ * Packet coalesce feature helps to reduce number of received interrupts
+ * to host by buffering these packets in firmware/hardware for some
+ * predefined time. Received interrupt will be generated when one of the
+ * following events occur.
+ * a) Expiration of hardware timer whose expiration time is set to maximum
+ * coalescing delay of matching coalesce rule.
+ * b) Coalescing buffer in hardware reaches it's limit.
+ * c) Packet doesn't match any of the configured coalesce rules.
+ *
+ * User needs to configure following parameters for creating a coalesce
+ * rule.
+ * a) Maximum coalescing delay
+ * b) List of packet patterns which needs to be matched
+ * c) Condition for coalescence. pattern 'match' or 'no match'
+ * Multiple such rules can be created.
+ */
+
+/**
  * enum nl80211_commands - supported nl80211 commands
  *
  * @NL80211_CMD_UNSPEC: unspecified command to catch errors
@@ -648,6 +673,19 @@
  * @NL80211_CMD_CRIT_PROTOCOL_STOP: Indicates the connection reliability can
  *	return back to normal.
  *
+ * @NL80211_CMD_GET_COALESCE: Get currently supported coalesce rules.
+ * @NL80211_CMD_SET_COALESCE: Configure coalesce rules or clear existing rules.
+ *
+ * @NL80211_CMD_CHANNEL_SWITCH: Perform a channel switch by announcing the
+ *	the new channel information (Channel Switch Announcement - CSA)
+ *	in the beacon for some time (as defined in the
+ *	%NL80211_ATTR_CH_SWITCH_COUNT parameter) and then change to the
+ *	new channel. Userspace provides the new channel information (using
+ *	%NL80211_ATTR_WIPHY_FREQ and the attributes determining channel
+ *	width). %NL80211_ATTR_CH_SWITCH_BLOCK_TX may be supplied to inform
+ *	other station that transmission must be blocked until the channel
+ *	switch is complete.
+ *
  * @NL80211_CMD_MAX: highest used command number
  * @__NL80211_CMD_AFTER_LAST: internal use
  */
@@ -810,6 +848,11 @@ enum nl80211_commands {
 	NL80211_CMD_CRIT_PROTOCOL_START,
 	NL80211_CMD_CRIT_PROTOCOL_STOP,
 
+	NL80211_CMD_GET_COALESCE,
+	NL80211_CMD_SET_COALESCE,
+
+	NL80211_CMD_CHANNEL_SWITCH,
+
 	/* add new commands above here */
 
 	/* used to define NL80211_CMD_MAX below */
@@ -1436,6 +1479,20 @@ enum nl80211_commands {
  *	allowed to be used with the first @NL80211_CMD_SET_STATION command to
  *	update a TDLS peer STA entry.
  *
+ * @NL80211_ATTR_COALESCE_RULE: Coalesce rule information.
+ *
+ * @NL80211_ATTR_CH_SWITCH_COUNT: u32 attribute specifying the number of TBTT's
+ *	until the channel switch event.
+ * @NL80211_ATTR_CH_SWITCH_BLOCK_TX: flag attribute specifying that transmission
+ *	must be blocked on the current channel (before the channel switch
+ *	operation).
+ * @NL80211_ATTR_CSA_IES: Nested set of attributes containing the IE information
+ *	for the time while performing a channel switch.
+ * @NL80211_ATTR_CSA_C_OFF_BEACON: Offset of the channel switch counter
+ *	field in the beacons tail (%NL80211_ATTR_BEACON_TAIL).
+ * @NL80211_ATTR_CSA_C_OFF_PRESP: Offset of the channel switch counter
+ *	field in the probe response (%NL80211_ATTR_PROBE_RESP).
+ *
  * @NL80211_ATTR_MAX: highest attribute number currently defined
  * @__NL80211_ATTR_AFTER_LAST: internal use
  */
@@ -1736,6 +1793,14 @@ enum nl80211_attrs {
 
 	NL80211_ATTR_PEER_AID,
 
+	NL80211_ATTR_COALESCE_RULE,
+
+	NL80211_ATTR_CH_SWITCH_COUNT,
+	NL80211_ATTR_CH_SWITCH_BLOCK_TX,
+	NL80211_ATTR_CSA_IES,
+	NL80211_ATTR_CSA_C_OFF_BEACON,
+	NL80211_ATTR_CSA_C_OFF_PRESP,
+
 	/* add attributes here, update the policy in nl80211.c */
 
 	__NL80211_ATTR_AFTER_LAST,
@@ -2773,6 +2838,21 @@ enum nl80211_chan_width {
 };
 
 /**
+ * enum nl80211_bss_scan_width - control channel width for a BSS
+ *
+ * These values are used with the %NL80211_BSS_CHAN_WIDTH attribute.
+ *
+ * @NL80211_BSS_CHAN_WIDTH_20: control channel is 20 MHz wide or compatible
+ * @NL80211_BSS_CHAN_WIDTH_10: control channel is 10 MHz wide
+ * @NL80211_BSS_CHAN_WIDTH_5: control channel is 5 MHz wide
+ */
+enum nl80211_bss_scan_width {
+	NL80211_BSS_CHAN_WIDTH_20,
+	NL80211_BSS_CHAN_WIDTH_10,
+	NL80211_BSS_CHAN_WIDTH_5,
+};
+
+/**
  * enum nl80211_bss - netlink attributes for a BSS
  *
  * @__NL80211_BSS_INVALID: invalid
@@ -2796,6 +2876,8 @@ enum nl80211_chan_width {
  * @NL80211_BSS_BEACON_IES: binary attribute containing the raw information
  *	elements from a Beacon frame (bin); not present if no Beacon frame has
  *	yet been received
+ * @NL80211_BSS_CHAN_WIDTH: channel width of the control channel
+ *	(u32, enum nl80211_bss_scan_width)
  * @__NL80211_BSS_AFTER_LAST: internal
  * @NL80211_BSS_MAX: highest BSS attribute
  */
@@ -2812,6 +2894,7 @@ enum nl80211_bss {
 	NL80211_BSS_STATUS,
 	NL80211_BSS_SEEN_MS_AGO,
 	NL80211_BSS_BEACON_IES,
+	NL80211_BSS_CHAN_WIDTH,
 
 	/* keep last */
 	__NL80211_BSS_AFTER_LAST,
@@ -3060,11 +3143,11 @@ enum nl80211_tx_power_setting {
 };
 
 /**
- * enum nl80211_wowlan_packet_pattern_attr - WoWLAN packet pattern attribute
- * @__NL80211_WOWLAN_PKTPAT_INVALID: invalid number for nested attribute
- * @NL80211_WOWLAN_PKTPAT_PATTERN: the pattern, values where the mask has
+ * enum nl80211_packet_pattern_attr - packet pattern attribute
+ * @__NL80211_PKTPAT_INVALID: invalid number for nested attribute
+ * @NL80211_PKTPAT_PATTERN: the pattern, values where the mask has
  *	a zero bit are ignored
- * @NL80211_WOWLAN_PKTPAT_MASK: pattern mask, must be long enough to have
+ * @NL80211_PKTPAT_MASK: pattern mask, must be long enough to have
  *	a bit for each byte in the pattern. The lowest-order bit corresponds
  *	to the first byte of the pattern, but the bytes of the pattern are
  *	in a little-endian-like format, i.e. the 9th byte of the pattern
@@ -3075,39 +3158,50 @@ enum nl80211_tx_power_setting {
  *	Note that the pattern matching is done as though frames were not
  *	802.11 frames but 802.3 frames, i.e. the frame is fully unpacked
  *	first (including SNAP header unpacking) and then matched.
- * @NL80211_WOWLAN_PKTPAT_OFFSET: packet offset, pattern is matched after
+ * @NL80211_PKTPAT_OFFSET: packet offset, pattern is matched after
  *	these fixed number of bytes of received packet
- * @NUM_NL80211_WOWLAN_PKTPAT: number of attributes
- * @MAX_NL80211_WOWLAN_PKTPAT: max attribute number
+ * @NUM_NL80211_PKTPAT: number of attributes
+ * @MAX_NL80211_PKTPAT: max attribute number
  */
-enum nl80211_wowlan_packet_pattern_attr {
-	__NL80211_WOWLAN_PKTPAT_INVALID,
-	NL80211_WOWLAN_PKTPAT_MASK,
-	NL80211_WOWLAN_PKTPAT_PATTERN,
-	NL80211_WOWLAN_PKTPAT_OFFSET,
+enum nl80211_packet_pattern_attr {
+	__NL80211_PKTPAT_INVALID,
+	NL80211_PKTPAT_MASK,
+	NL80211_PKTPAT_PATTERN,
+	NL80211_PKTPAT_OFFSET,
 
-	NUM_NL80211_WOWLAN_PKTPAT,
-	MAX_NL80211_WOWLAN_PKTPAT = NUM_NL80211_WOWLAN_PKTPAT - 1,
+	NUM_NL80211_PKTPAT,
+	MAX_NL80211_PKTPAT = NUM_NL80211_PKTPAT - 1,
 };
 
 /**
- * struct nl80211_wowlan_pattern_support - pattern support information
+ * struct nl80211_pattern_support - packet pattern support information
  * @max_patterns: maximum number of patterns supported
  * @min_pattern_len: minimum length of each pattern
  * @max_pattern_len: maximum length of each pattern
  * @max_pkt_offset: maximum Rx packet offset
  *
  * This struct is carried in %NL80211_WOWLAN_TRIG_PKT_PATTERN when
- * that is part of %NL80211_ATTR_WOWLAN_TRIGGERS_SUPPORTED in the
- * capability information given by the kernel to userspace.
+ * that is part of %NL80211_ATTR_WOWLAN_TRIGGERS_SUPPORTED or in
+ * %NL80211_ATTR_COALESCE_RULE_PKT_PATTERN when that is part of
+ * %NL80211_ATTR_COALESCE_RULE in the capability information given
+ * by the kernel to userspace.
  */
-struct nl80211_wowlan_pattern_support {
+struct nl80211_pattern_support {
 	__u32 max_patterns;
 	__u32 min_pattern_len;
 	__u32 max_pattern_len;
 	__u32 max_pkt_offset;
 } __attribute__((packed));
 
+/* only for backward compatibility */
+#define __NL80211_WOWLAN_PKTPAT_INVALID __NL80211_PKTPAT_INVALID
+#define NL80211_WOWLAN_PKTPAT_MASK NL80211_PKTPAT_MASK
+#define NL80211_WOWLAN_PKTPAT_PATTERN NL80211_PKTPAT_PATTERN
+#define NL80211_WOWLAN_PKTPAT_OFFSET NL80211_PKTPAT_OFFSET
+#define NUM_NL80211_WOWLAN_PKTPAT NUM_NL80211_PKTPAT
+#define MAX_NL80211_WOWLAN_PKTPAT MAX_NL80211_PKTPAT
+#define nl80211_wowlan_pattern_support nl80211_pattern_support
+
 /**
  * enum nl80211_wowlan_triggers - WoWLAN trigger definitions
  * @__NL80211_WOWLAN_TRIG_INVALID: invalid number for nested attributes
@@ -3127,7 +3221,7 @@ struct nl80211_wowlan_pattern_support {
  *	pattern matching is done after the packet is converted to the MSDU.
  *
  *	In %NL80211_ATTR_WOWLAN_TRIGGERS_SUPPORTED, it is a binary attribute
- *	carrying a &struct nl80211_wowlan_pattern_support.
+ *	carrying a &struct nl80211_pattern_support.
  *
  *	When reporting wakeup. it is a u32 attribute containing the 0-based
  *	index of the pattern that caused the wakeup, in the patterns passed
@@ -3284,7 +3378,7 @@ struct nl80211_wowlan_tcp_data_token_feature {
  * @NL80211_WOWLAN_TCP_WAKE_PAYLOAD: wake packet payload, for advertising a
  *	u32 attribute holding the maximum length
  * @NL80211_WOWLAN_TCP_WAKE_MASK: Wake packet payload mask, not used for
- *	feature advertising. The mask works like @NL80211_WOWLAN_PKTPAT_MASK
+ *	feature advertising. The mask works like @NL80211_PKTPAT_MASK
  *	but on the TCP payload only.
  * @NUM_NL80211_WOWLAN_TCP: number of TCP attributes
  * @MAX_NL80211_WOWLAN_TCP: highest attribute number
@@ -3309,6 +3403,55 @@ enum nl80211_wowlan_tcp_attrs {
 };
 
 /**
+ * struct nl80211_coalesce_rule_support - coalesce rule support information
+ * @max_rules: maximum number of rules supported
+ * @pat: packet pattern support information
+ * @max_delay: maximum supported coalescing delay in msecs
+ *
+ * This struct is carried in %NL80211_ATTR_COALESCE_RULE in the
+ * capability information given by the kernel to userspace.
+ */
+struct nl80211_coalesce_rule_support {
+	__u32 max_rules;
+	struct nl80211_pattern_support pat;
+	__u32 max_delay;
+} __attribute__((packed));
+
+/**
+ * enum nl80211_attr_coalesce_rule - coalesce rule attribute
+ * @__NL80211_COALESCE_RULE_INVALID: invalid number for nested attribute
+ * @NL80211_ATTR_COALESCE_RULE_DELAY: delay in msecs used for packet coalescing
+ * @NL80211_ATTR_COALESCE_RULE_CONDITION: condition for packet coalescence,
+ *	see &enum nl80211_coalesce_condition.
+ * @NL80211_ATTR_COALESCE_RULE_PKT_PATTERN: packet offset, pattern is matched
+ *	after these fixed number of bytes of received packet
+ * @NUM_NL80211_ATTR_COALESCE_RULE: number of attributes
+ * @NL80211_ATTR_COALESCE_RULE_MAX: max attribute number
+ */
+enum nl80211_attr_coalesce_rule {
+	__NL80211_COALESCE_RULE_INVALID,
+	NL80211_ATTR_COALESCE_RULE_DELAY,
+	NL80211_ATTR_COALESCE_RULE_CONDITION,
+	NL80211_ATTR_COALESCE_RULE_PKT_PATTERN,
+
+	/* keep last */
+	NUM_NL80211_ATTR_COALESCE_RULE,
+	NL80211_ATTR_COALESCE_RULE_MAX = NUM_NL80211_ATTR_COALESCE_RULE - 1
+};
+
+/**
+ * enum nl80211_coalesce_condition - coalesce rule conditions
+ * @NL80211_COALESCE_CONDITION_MATCH: coalaesce Rx packets when patterns
+ *	in a rule are matched.
+ * @NL80211_COALESCE_CONDITION_NO_MATCH: coalesce Rx packets when patterns
+ *	in a rule are not matched.
+ */
+enum nl80211_coalesce_condition {
+	NL80211_COALESCE_CONDITION_MATCH,
+	NL80211_COALESCE_CONDITION_NO_MATCH
+};
+
+/**
  * enum nl80211_iface_limit_attrs - limit attributes
  * @NL80211_IFACE_LIMIT_UNSPEC: (reserved)
  * @NL80211_IFACE_LIMIT_MAX: maximum number of interfaces that