Merge tag 'for-linus-20130909' of git://git.infradead.org/linux-mtd

Pull mtd updates from David Woodhouse:
 - factor out common code from MTD tests
 - nand-gpio cleanup and portability to non-ARM
 - m25p80 support for 4-byte addressing chips, other new chips
 - pxa3xx cleanup and support for new platforms
 - remove obsolete alauda, octagon-5066 drivers
 - erase/write support for bcm47xxsflash
 - improve detection of ECC requirements for NAND, controller setup
 - NFC acceleration support for atmel-nand, read/write via SRAM
 - etc

* tag 'for-linus-20130909' of git://git.infradead.org/linux-mtd: (184 commits)
  mtd: chips: Add support for PMC SPI Flash chips in m25p80.c
  mtd: ofpart: use for_each_child_of_node() macro
  mtd: mtdswap: replace strict_strtoul() with kstrtoul()
  mtd cs553x_nand: use kzalloc() instead of memset
  mtd: atmel_nand: fix error return code in atmel_nand_probe()
  mtd: bcm47xxsflash: writing support
  mtd: bcm47xxsflash: implement erasing support
  mtd: bcm47xxsflash: convert to module_platform_driver instead of init/exit
  mtd: bcm47xxsflash: convert kzalloc to avoid invalid access
  mtd: remove alauda driver
  mtd: nand: mxc_nand: mark 'const' properly
  mtd: maps: cfi_flagadm: add missing __iomem annotation
  mtd: spear_smi: add missing __iomem annotation
  mtd: r852: Staticize local symbols
  mtd: nandsim: Staticize local symbols
  mtd: impa7: add missing __iomem annotation
  mtd: sm_ftl: Staticize local symbols
  mtd: m25p80: add support for mr25h10
  mtd: m25p80: make CONFIG_M25PXX_USE_FAST_READ safe to enable
  mtd: m25p80: Pass flags through CAT25_INFO macro
  ...

6 files changed, 86 insertions, 20 deletions

diff --git a/include/linux/mtd/bbm.h b/include/linux/mtd/bbm.h
index 211ff67..95fc482 100644
--- a/include/linux/mtd/bbm.h
+++ b/include/linux/mtd/bbm.h
@@ -93,8 +93,6 @@ struct nand_bbt_descr {
 #define NAND_BBT_CREATE_EMPTY	0x00000400
 /* Search good / bad pattern through all pages of a block */
 #define NAND_BBT_SCANALLPAGES	0x00000800
-/* Scan block empty during good / bad block scan */
-#define NAND_BBT_SCANEMPTY	0x00001000
 /* Write bbt if neccecary */
 #define NAND_BBT_WRITE		0x00002000
 /* Read and write back block contents when writing bbt */
diff --git a/include/linux/mtd/fsmc.h b/include/linux/mtd/fsmc.h
index d6ed61e..c8be32e 100644
--- a/include/linux/mtd/fsmc.h
+++ b/include/linux/mtd/fsmc.h
@@ -137,6 +137,7 @@ enum access_mode {
 
 /**
  * fsmc_nand_platform_data - platform specific NAND controller config
+ * @nand_timings: timing setup for the physical NAND interface
  * @partitions: partition table for the platform, use a default fallback
  * if this is NULL
  * @nr_partitions: the number of partitions in the previous entry
diff --git a/include/linux/mtd/mtd.h b/include/linux/mtd/mtd.h
index a5cf4e8..f9bfe52 100644
--- a/include/linux/mtd/mtd.h
+++ b/include/linux/mtd/mtd.h
@@ -173,6 +173,9 @@ struct mtd_info {
 	/* ECC layout structure pointer - read only! */
 	struct nand_ecclayout *ecclayout;
 
+	/* the ecc step size. */
+	unsigned int ecc_step_size;
+
 	/* max number of correctible bit errors per ecc step */
 	unsigned int ecc_strength;
 
diff --git a/include/linux/mtd/nand.h b/include/linux/mtd/nand.h
index ab63634..ac8e89d 100644
--- a/include/linux/mtd/nand.h
+++ b/include/linux/mtd/nand.h
@@ -56,7 +56,7 @@ extern int nand_unlock(struct mtd_info *mtd, loff_t ofs, uint64_t len);
  * is supported now. If you add a chip with bigger oobsize/page
  * adjust this accordingly.
  */
-#define NAND_MAX_OOBSIZE	640
+#define NAND_MAX_OOBSIZE	744
 #define NAND_MAX_PAGESIZE	8192
 
 /*
@@ -202,6 +202,10 @@ typedef enum {
 /* Keep gcc happy */
 struct nand_chip;
 
+/* ONFI features */
+#define ONFI_FEATURE_16_BIT_BUS		(1 << 0)
+#define ONFI_FEATURE_EXT_PARAM_PAGE	(1 << 7)
+
 /* ONFI timing mode, used in both asynchronous and synchronous mode */
 #define ONFI_TIMING_MODE_0		(1 << 0)
 #define ONFI_TIMING_MODE_1		(1 << 1)
@@ -217,6 +221,9 @@ struct nand_chip;
 /* ONFI subfeature parameters length */
 #define ONFI_SUBFEATURE_PARAM_LEN	4
 
+/* ONFI optional commands SET/GET FEATURES supported? */
+#define ONFI_OPT_CMD_SET_GET_FEATURES	(1 << 2)
+
 struct nand_onfi_params {
 	/* rev info and features block */
 	/* 'O' 'N' 'F' 'I'  */
@@ -224,7 +231,10 @@ struct nand_onfi_params {
 	__le16 revision;
 	__le16 features;
 	__le16 opt_cmd;
-	u8 reserved[22];
+	u8 reserved0[2];
+	__le16 ext_param_page_length; /* since ONFI 2.1 */
+	u8 num_of_param_pages;        /* since ONFI 2.1 */
+	u8 reserved1[17];
 
 	/* manufacturer information block */
 	char manufacturer[12];
@@ -281,6 +291,40 @@ struct nand_onfi_params {
 
 #define ONFI_CRC_BASE	0x4F4E
 
+/* Extended ECC information Block Definition (since ONFI 2.1) */
+struct onfi_ext_ecc_info {
+	u8 ecc_bits;
+	u8 codeword_size;
+	__le16 bb_per_lun;
+	__le16 block_endurance;
+	u8 reserved[2];
+} __packed;
+
+#define ONFI_SECTION_TYPE_0	0	/* Unused section. */
+#define ONFI_SECTION_TYPE_1	1	/* for additional sections. */
+#define ONFI_SECTION_TYPE_2	2	/* for ECC information. */
+struct onfi_ext_section {
+	u8 type;
+	u8 length;
+} __packed;
+
+#define ONFI_EXT_SECTION_MAX 8
+
+/* Extended Parameter Page Definition (since ONFI 2.1) */
+struct onfi_ext_param_page {
+	__le16 crc;
+	u8 sig[4];             /* 'E' 'P' 'P' 'S' */
+	u8 reserved0[10];
+	struct onfi_ext_section sections[ONFI_EXT_SECTION_MAX];
+
+	/*
+	 * The actual size of the Extended Parameter Page is in
+	 * @ext_param_page_length of nand_onfi_params{}.
+	 * The following are the variable length sections.
+	 * So we do not add any fields below. Please see the ONFI spec.
+	 */
+} __packed;
+
 /**
  * struct nand_hw_control - Control structure for hardware controller (e.g ECC generator) shared among independent devices
  * @lock:               protection lock
@@ -390,8 +434,8 @@ struct nand_buffers {
  * @write_buf:		[REPLACEABLE] write data from the buffer to the chip
  * @read_buf:		[REPLACEABLE] read data from the chip into the buffer
  * @select_chip:	[REPLACEABLE] select chip nr
- * @block_bad:		[REPLACEABLE] check, if the block is bad
- * @block_markbad:	[REPLACEABLE] mark the block bad
+ * @block_bad:		[REPLACEABLE] check if a block is bad, using OOB markers
+ * @block_markbad:	[REPLACEABLE] mark a block bad
  * @cmd_ctrl:		[BOARDSPECIFIC] hardwarespecific function for controlling
  *			ALE/CLE/nCE. Also used to write command and address
  * @init_size:		[BOARDSPECIFIC] hardwarespecific function for setting
@@ -434,6 +478,12 @@ struct nand_buffers {
  *			bad block marker position; i.e., BBM == 11110111b is
  *			not bad when badblockbits == 7
  * @cellinfo:		[INTERN] MLC/multichip data from chip ident
+ * @ecc_strength_ds:	[INTERN] ECC correctability from the datasheet.
+ *			Minimum amount of bit errors per @ecc_step_ds guaranteed
+ *			to be correctable. If unknown, set to zero.
+ * @ecc_step_ds:	[INTERN] ECC step required by the @ecc_strength_ds,
+ *                      also from the datasheet. It is the recommended ECC step
+ *			size, if known; if unknown, set to zero.
  * @numchips:		[INTERN] number of physical chips
  * @chipsize:		[INTERN] the size of one chip for multichip arrays
  * @pagemask:		[INTERN] page number mask = number of (pages / chip) - 1
@@ -510,6 +560,8 @@ struct nand_chip {
 	unsigned int pagebuf_bitflips;
 	int subpagesize;
 	uint8_t cellinfo;
+	uint16_t ecc_strength_ds;
+	uint16_t ecc_step_ds;
 	int badblockpos;
 	int badblockbits;
 
@@ -576,6 +628,11 @@ struct nand_chip {
 	{ .name = (nm), {{ .dev_id = (devid) }}, .chipsize = (chipsz), \
 	  .options = (opts) }
 
+#define NAND_ECC_INFO(_strength, _step)	\
+			{ .strength_ds = (_strength), .step_ds = (_step) }
+#define NAND_ECC_STRENGTH(type)		((type)->ecc.strength_ds)
+#define NAND_ECC_STEP(type)		((type)->ecc.step_ds)
+
 /**
  * struct nand_flash_dev - NAND Flash Device ID Structure
  * @name: a human-readable name of the NAND chip
@@ -593,6 +650,12 @@ struct nand_chip {
  * @options: stores various chip bit options
  * @id_len: The valid length of the @id.
  * @oobsize: OOB size
+ * @ecc.strength_ds: The ECC correctability from the datasheet, same as the
+ *                   @ecc_strength_ds in nand_chip{}.
+ * @ecc.step_ds: The ECC step required by the @ecc.strength_ds, same as the
+ *               @ecc_step_ds in nand_chip{}, also from the datasheet.
+ *               For example, the "4bit ECC for each 512Byte" can be set with
+ *               NAND_ECC_INFO(4, 512).
  */
 struct nand_flash_dev {
 	char *name;
@@ -609,6 +672,10 @@ struct nand_flash_dev {
 	unsigned int options;
 	uint16_t id_len;
 	uint16_t oobsize;
+	struct {
+		uint16_t strength_ds;
+		uint16_t step_ds;
+	} ecc;
 };
 
 /**
@@ -625,8 +692,8 @@ extern struct nand_flash_dev nand_flash_ids[];
 extern struct nand_manufacturers nand_manuf_ids[];
 
 extern int nand_scan_bbt(struct mtd_info *mtd, struct nand_bbt_descr *bd);
-extern int nand_update_bbt(struct mtd_info *mtd, loff_t offs);
 extern int nand_default_bbt(struct mtd_info *mtd);
+extern int nand_markbad_bbt(struct mtd_info *mtd, loff_t offs);
 extern int nand_isbad_bbt(struct mtd_info *mtd, loff_t offs, int allowbbt);
 extern int nand_erase_nand(struct mtd_info *mtd, struct erase_info *instr,
 			   int allowbbt);
@@ -708,6 +775,12 @@ struct platform_nand_chip *get_platform_nandchip(struct mtd_info *mtd)
 	return chip->priv;
 }
 
+/* return the supported features. */
+static inline int onfi_feature(struct nand_chip *chip)
+{
+	return chip->onfi_version ? le16_to_cpu(chip->onfi_params.features) : 0;
+}
+
 /* return the supported asynchronous timing mode. */
 static inline int onfi_get_async_timing_mode(struct nand_chip *chip)
 {
diff --git a/include/linux/platform_data/atmel.h b/include/linux/platform_data/atmel.h
index 6a293b7..cea9f70 100644
--- a/include/linux/platform_data/atmel.h
+++ b/include/linux/platform_data/atmel.h
@@ -71,6 +71,10 @@ struct atmel_nand_data {
 	u8		on_flash_bbt;		/* bbt on flash */
 	struct mtd_partition *parts;
 	unsigned int	num_parts;
+	bool		has_dma;		/* support dma transfer */
+
+	/* default is false, only for at32ap7000 chip is true */
+	bool		need_reset_workaround;
 };
 
  /* Serial */
diff --git a/include/linux/platform_data/mtd-nand-pxa3xx.h b/include/linux/platform_data/mtd-nand-pxa3xx.h
index c42f39f..ffb8019 100644
--- a/include/linux/platform_data/mtd-nand-pxa3xx.h
+++ b/include/linux/platform_data/mtd-nand-pxa3xx.h
@@ -16,19 +16,6 @@ struct pxa3xx_nand_timing {
 	unsigned int	tAR;  /* ND_ALE low to ND_nRE low delay */
 };
 
-struct pxa3xx_nand_cmdset {
-	uint16_t	read1;
-	uint16_t	read2;
-	uint16_t	program;
-	uint16_t	read_status;
-	uint16_t	read_id;
-	uint16_t	erase;
-	uint16_t	reset;
-	uint16_t	lock;
-	uint16_t	unlock;
-	uint16_t	lock_status;
-};
-
 struct pxa3xx_nand_flash {
 	char		*name;
 	uint32_t	chip_id;