diff options
| -rw-r--r-- | drivers/input/misc/winbond-cir.c | 213 |
1 files changed, 104 insertions, 109 deletions
diff --git a/drivers/input/misc/winbond-cir.c b/drivers/input/misc/winbond-cir.c index c8f5a9a..cbec3df 100644 --- a/drivers/input/misc/winbond-cir.c +++ b/drivers/input/misc/winbond-cir.c @@ -538,6 +538,7 @@ wbcir_reset_irdata(struct wbcir_data *data) data->irdata_count = 0; data->irdata_off = 0; data->irdata_error = 0; + data->idle_count = 0; } /* Adds one bit of irdata */ @@ -1006,7 +1007,6 @@ wbcir_irq_handler(int irqno, void *cookie) } wbcir_reset_irdata(data); - data->idle_count = 0; } out: @@ -1018,7 +1018,7 @@ out: /***************************************************************************** * - * SUSPEND/RESUME FUNCTIONS + * SETUP/INIT/SUSPEND/RESUME FUNCTIONS * *****************************************************************************/ @@ -1197,7 +1197,16 @@ finish: } /* Disable interrupts */ + wbcir_select_bank(data, WBCIR_BANK_0); outb(WBCIR_IRQ_NONE, data->sbase + WBCIR_REG_SP3_IER); + + /* + * ACPI will set the HW disable bit for SP3 which means that the + * output signals are left in an undefined state which may cause + * spurious interrupts which we need to ignore until the hardware + * is reinitialized. + */ + disable_irq(data->irq); } static int @@ -1207,37 +1216,15 @@ wbcir_suspend(struct pnp_dev *device, pm_message_t state) return 0; } -static int -wbcir_resume(struct pnp_dev *device) -{ - struct wbcir_data *data = pnp_get_drvdata(device); - - /* Clear BUFF_EN, Clear END_EN, Clear MATCH_EN */ - wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_EV_EN, 0x00, 0x07); - - /* Clear CEIR_EN */ - wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_CTL, 0x00, 0x01); - - /* Enable interrupts */ - wbcir_reset_irdata(data); - outb(WBCIR_IRQ_RX | WBCIR_IRQ_ERR, data->sbase + WBCIR_REG_SP3_IER); - - return 0; -} - - - -/***************************************************************************** - * - * SETUP/INIT FUNCTIONS - * - *****************************************************************************/ - static void -wbcir_cfg_ceir(struct wbcir_data *data) +wbcir_init_hw(struct wbcir_data *data) { u8 tmp; + /* Disable interrupts */ + wbcir_select_bank(data, WBCIR_BANK_0); + outb(WBCIR_IRQ_NONE, data->sbase + WBCIR_REG_SP3_IER); + /* Set PROT_SEL, RX_INV, Clear CEIR_EN (needed for the led) */ tmp = protocol << 4; if (invert) @@ -1264,6 +1251,93 @@ wbcir_cfg_ceir(struct wbcir_data *data) * set SP3_IRRX_SW to binary 01, helpfully not documented */ outb(0x10, data->ebase + WBCIR_REG_ECEIR_CTS); + + /* Enable extended mode */ + wbcir_select_bank(data, WBCIR_BANK_2); + outb(WBCIR_EXT_ENABLE, data->sbase + WBCIR_REG_SP3_EXCR1); + + /* + * Configure baud generator, IR data will be sampled at + * a bitrate of: (24Mhz * prescaler) / (divisor * 16). + * + * The ECIR registers include a flag to change the + * 24Mhz clock freq to 48Mhz. + * + * It's not documented in the specs, but fifo levels + * other than 16 seems to be unsupported. + */ + + /* prescaler 1.0, tx/rx fifo lvl 16 */ + outb(0x30, data->sbase + WBCIR_REG_SP3_EXCR2); + + /* Set baud divisor to generate one byte per bit/cell */ + switch (protocol) { + case IR_PROTOCOL_RC5: + outb(0xA7, data->sbase + WBCIR_REG_SP3_BGDL); + break; + case IR_PROTOCOL_RC6: + outb(0x53, data->sbase + WBCIR_REG_SP3_BGDL); + break; + case IR_PROTOCOL_NEC: + outb(0x69, data->sbase + WBCIR_REG_SP3_BGDL); + break; + } + outb(0x00, data->sbase + WBCIR_REG_SP3_BGDH); + + /* Set CEIR mode */ + wbcir_select_bank(data, WBCIR_BANK_0); + outb(0xC0, data->sbase + WBCIR_REG_SP3_MCR); + inb(data->sbase + WBCIR_REG_SP3_LSR); /* Clear LSR */ + inb(data->sbase + WBCIR_REG_SP3_MSR); /* Clear MSR */ + + /* Disable RX demod, run-length encoding/decoding, set freq span */ + wbcir_select_bank(data, WBCIR_BANK_7); + outb(0x10, data->sbase + WBCIR_REG_SP3_RCCFG); + + /* Disable timer */ + wbcir_select_bank(data, WBCIR_BANK_4); + outb(0x00, data->sbase + WBCIR_REG_SP3_IRCR1); + + /* Enable MSR interrupt, Clear AUX_IRX */ + wbcir_select_bank(data, WBCIR_BANK_5); + outb(0x00, data->sbase + WBCIR_REG_SP3_IRCR2); + + /* Disable CRC */ + wbcir_select_bank(data, WBCIR_BANK_6); + outb(0x20, data->sbase + WBCIR_REG_SP3_IRCR3); + + /* Set RX/TX (de)modulation freq, not really used */ + wbcir_select_bank(data, WBCIR_BANK_7); + outb(0xF2, data->sbase + WBCIR_REG_SP3_IRRXDC); + outb(0x69, data->sbase + WBCIR_REG_SP3_IRTXMC); + + /* Set invert and pin direction */ + if (invert) + outb(0x10, data->sbase + WBCIR_REG_SP3_IRCFG4); + else + outb(0x00, data->sbase + WBCIR_REG_SP3_IRCFG4); + + /* Set FIFO thresholds (RX = 8, TX = 3), reset RX/TX */ + wbcir_select_bank(data, WBCIR_BANK_0); + outb(0x97, data->sbase + WBCIR_REG_SP3_FCR); + + /* Clear AUX status bits */ + outb(0xE0, data->sbase + WBCIR_REG_SP3_ASCR); + + /* Enable interrupts */ + wbcir_reset_irdata(data); + outb(WBCIR_IRQ_RX | WBCIR_IRQ_ERR, data->sbase + WBCIR_REG_SP3_IER); +} + +static int +wbcir_resume(struct pnp_dev *device) +{ + struct wbcir_data *data = pnp_get_drvdata(device); + + wbcir_init_hw(data); + enable_irq(data->irq); + + return 0; } static int __devinit @@ -1393,86 +1467,7 @@ wbcir_probe(struct pnp_dev *device, const struct pnp_device_id *dev_id) device_init_wakeup(&device->dev, 1); - wbcir_cfg_ceir(data); - - /* Disable interrupts */ - wbcir_select_bank(data, WBCIR_BANK_0); - outb(WBCIR_IRQ_NONE, data->sbase + WBCIR_REG_SP3_IER); - - /* Enable extended mode */ - wbcir_select_bank(data, WBCIR_BANK_2); - outb(WBCIR_EXT_ENABLE, data->sbase + WBCIR_REG_SP3_EXCR1); - - /* - * Configure baud generator, IR data will be sampled at - * a bitrate of: (24Mhz * prescaler) / (divisor * 16). - * - * The ECIR registers include a flag to change the - * 24Mhz clock freq to 48Mhz. - * - * It's not documented in the specs, but fifo levels - * other than 16 seems to be unsupported. - */ - - /* prescaler 1.0, tx/rx fifo lvl 16 */ - outb(0x30, data->sbase + WBCIR_REG_SP3_EXCR2); - - /* Set baud divisor to generate one byte per bit/cell */ - switch (protocol) { - case IR_PROTOCOL_RC5: - outb(0xA7, data->sbase + WBCIR_REG_SP3_BGDL); - break; - case IR_PROTOCOL_RC6: - outb(0x53, data->sbase + WBCIR_REG_SP3_BGDL); - break; - case IR_PROTOCOL_NEC: - outb(0x69, data->sbase + WBCIR_REG_SP3_BGDL); - break; - } - outb(0x00, data->sbase + WBCIR_REG_SP3_BGDH); - - /* Set CEIR mode */ - wbcir_select_bank(data, WBCIR_BANK_0); - outb(0xC0, data->sbase + WBCIR_REG_SP3_MCR); - inb(data->sbase + WBCIR_REG_SP3_LSR); /* Clear LSR */ - inb(data->sbase + WBCIR_REG_SP3_MSR); /* Clear MSR */ - - /* Disable RX demod, run-length encoding/decoding, set freq span */ - wbcir_select_bank(data, WBCIR_BANK_7); - outb(0x10, data->sbase + WBCIR_REG_SP3_RCCFG); - - /* Disable timer */ - wbcir_select_bank(data, WBCIR_BANK_4); - outb(0x00, data->sbase + WBCIR_REG_SP3_IRCR1); - - /* Enable MSR interrupt, Clear AUX_IRX */ - wbcir_select_bank(data, WBCIR_BANK_5); - outb(0x00, data->sbase + WBCIR_REG_SP3_IRCR2); - - /* Disable CRC */ - wbcir_select_bank(data, WBCIR_BANK_6); - outb(0x20, data->sbase + WBCIR_REG_SP3_IRCR3); - - /* Set RX/TX (de)modulation freq, not really used */ - wbcir_select_bank(data, WBCIR_BANK_7); - outb(0xF2, data->sbase + WBCIR_REG_SP3_IRRXDC); - outb(0x69, data->sbase + WBCIR_REG_SP3_IRTXMC); - - /* Set invert and pin direction */ - if (invert) - outb(0x10, data->sbase + WBCIR_REG_SP3_IRCFG4); - else - outb(0x00, data->sbase + WBCIR_REG_SP3_IRCFG4); - - /* Set FIFO thresholds (RX = 8, TX = 3), reset RX/TX */ - wbcir_select_bank(data, WBCIR_BANK_0); - outb(0x97, data->sbase + WBCIR_REG_SP3_FCR); - - /* Clear AUX status bits */ - outb(0xE0, data->sbase + WBCIR_REG_SP3_ASCR); - - /* Enable interrupts */ - outb(WBCIR_IRQ_RX | WBCIR_IRQ_ERR, data->sbase + WBCIR_REG_SP3_IER); + wbcir_init_hw(data); return 0; |