summaryrefslogtreecommitdiff
diff options
context:
space:
mode:
Diffstat
-rw-r--r--Documentation/devicetree/bindings/reset/st,sti-powerdown.txt47
-rw-r--r--Documentation/devicetree/bindings/reset/st,sti-softreset.txt46
-rw-r--r--arch/arm/boot/dts/stih415-clock.dtsi14
-rw-r--r--arch/arm/boot/dts/stih415-pinctrl.dtsi204
-rw-r--r--arch/arm/boot/dts/stih415.dtsi70
-rw-r--r--arch/arm/boot/dts/stih416-clock.dtsi14
-rw-r--r--arch/arm/boot/dts/stih416-pinctrl.dtsi197
-rw-r--r--arch/arm/boot/dts/stih416.dtsi67
-rw-r--r--arch/arm/boot/dts/stih41x-b2000.dtsi22
-rw-r--r--arch/arm/boot/dts/stih41x-b2020.dtsi13
-rw-r--r--include/dt-bindings/reset-controller/stih415-resets.h26
-rw-r--r--include/dt-bindings/reset-controller/stih416-resets.h50
12 files changed, 770 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/reset/st,sti-powerdown.txt b/Documentation/devicetree/bindings/reset/st,sti-powerdown.txt
new file mode 100644
index 0000000..5ab26b7
--- /dev/null
+++ b/Documentation/devicetree/bindings/reset/st,sti-powerdown.txt
@@ -0,0 +1,47 @@
+STMicroelectronics STi family Sysconfig Peripheral Powerdown Reset Controller
+=============================================================================
+
+This binding describes a reset controller device that is used to enable and
+disable on-chip peripheral controllers such as USB and SATA, using
+"powerdown" control bits found in the STi family SoC system configuration
+registers. These have been grouped together into a single reset controller
+device for convenience.
+
+The actual action taken when powerdown is asserted is hardware dependent.
+However, when asserted it may not be possible to access the hardware's
+registers and after an assert/deassert sequence the hardware's previous state
+may no longer be valid.
+
+Please refer to reset.txt in this directory for common reset
+controller binding usage.
+
+Required properties:
+- compatible: Should be "st,<chip>-powerdown"
+ ex: "st,stih415-powerdown", "st,stih416-powerdown"
+- #reset-cells: 1, see below
+
+example:
+
+ powerdown: powerdown-controller {
+ #reset-cells = <1>;
+ compatible = "st,stih415-powerdown";
+ };
+
+
+Specifying powerdown control of devices
+=======================================
+
+Device nodes should specify the reset channel required in their "resets"
+property, containing a phandle to the powerdown device node and an
+index specifying which channel to use, as described in reset.txt
+
+example:
+
+ usb1: usb@fe200000 {
+ resets = <&powerdown STIH41X_USB1_POWERDOWN>;
+ };
+
+Macro definitions for the supported reset channels can be found in:
+
+include/dt-bindings/reset-controller/stih415-resets.h
+include/dt-bindings/reset-controller/stih416-resets.h
diff --git a/Documentation/devicetree/bindings/reset/st,sti-softreset.txt b/Documentation/devicetree/bindings/reset/st,sti-softreset.txt
new file mode 100644
index 0000000..a8d3d3c
--- /dev/null
+++ b/Documentation/devicetree/bindings/reset/st,sti-softreset.txt
@@ -0,0 +1,46 @@
+STMicroelectronics STi family Sysconfig Peripheral SoftReset Controller
+=============================================================================
+
+This binding describes a reset controller device that is used to enable and
+disable on-chip peripheral controllers such as USB and SATA, using
+"softreset" control bits found in the STi family SoC system configuration
+registers.
+
+The actual action taken when softreset is asserted is hardware dependent.
+However, when asserted it may not be possible to access the hardware's
+registers and after an assert/deassert sequence the hardware's previous state
+may no longer be valid.
+
+Please refer to reset.txt in this directory for common reset
+controller binding usage.
+
+Required properties:
+- compatible: Should be "st,<chip>-softreset" example:
+ "st,stih415-softreset" or "st,stih416-softreset";
+- #reset-cells: 1, see below
+
+example:
+
+ softreset: softreset-controller {
+ #reset-cells = <1>;
+ compatible = "st,stih415-softreset";
+ };
+
+
+Specifying softreset control of devices
+=======================================
+
+Device nodes should specify the reset channel required in their "resets"
+property, containing a phandle to the softreset device node and an
+index specifying which channel to use, as described in reset.txt
+
+example:
+
+ ethernet0{
+ resets = <&softreset STIH415_ETH0_SOFTRESET>;
+ };
+
+Macro definitions for the supported reset channels can be found in:
+
+include/dt-bindings/reset-controller/stih415-resets.h
+include/dt-bindings/reset-controller/stih416-resets.h
diff --git a/arch/arm/boot/dts/stih415-clock.dtsi b/arch/arm/boot/dts/stih415-clock.dtsi
index 174c799..d047dbc 100644
--- a/arch/arm/boot/dts/stih415-clock.dtsi
+++ b/arch/arm/boot/dts/stih415-clock.dtsi
@@ -34,5 +34,19 @@
compatible = "fixed-clock";
clock-frequency = <100000000>;
};
+
+ CLKS_GMAC0_PHY: clockgenA1@7 {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <25000000>;
+ clock-output-names = "CLKS_GMAC0_PHY";
+ };
+
+ CLKS_ETH1_PHY: clockgenA0@7 {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <25000000>;
+ clock-output-names = "CLKS_ETH1_PHY";
+ };
};
};
diff --git a/arch/arm/boot/dts/stih415-pinctrl.dtsi b/arch/arm/boot/dts/stih415-pinctrl.dtsi
index e56449d..f09fb10 100644
--- a/arch/arm/boot/dts/stih415-pinctrl.dtsi
+++ b/arch/arm/boot/dts/stih415-pinctrl.dtsi
@@ -7,6 +7,7 @@
* publishhed by the Free Software Foundation.
*/
#include "st-pincfg.h"
+#include <dt-bindings/interrupt-controller/arm-gic.h>
/ {
aliases {
@@ -45,35 +46,49 @@
#size-cells = <1>;
compatible = "st,stih415-sbc-pinctrl";
st,syscfg = <&syscfg_sbc>;
+ reg = <0xfe61f080 0x4>;
+ reg-names = "irqmux";
+ interrupts = <GIC_SPI 180 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts-names = "irqmux";
ranges = <0 0xfe610000 0x5000>;
PIO0: gpio@fe610000 {
gpio-controller;
#gpio-cells = <1>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
reg = <0 0x100>;
st,bank-name = "PIO0";
};
PIO1: gpio@fe611000 {
gpio-controller;
#gpio-cells = <1>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
reg = <0x1000 0x100>;
st,bank-name = "PIO1";
};
PIO2: gpio@fe612000 {
gpio-controller;
#gpio-cells = <1>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
reg = <0x2000 0x100>;
st,bank-name = "PIO2";
};
PIO3: gpio@fe613000 {
gpio-controller;
#gpio-cells = <1>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
reg = <0x3000 0x100>;
st,bank-name = "PIO3";
};
PIO4: gpio@fe614000 {
gpio-controller;
#gpio-cells = <1>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
reg = <0x4000 0x100>;
st,bank-name = "PIO4";
};
@@ -104,6 +119,64 @@
};
};
};
+
+ rc{
+ pinctrl_ir: ir0 {
+ st,pins {
+ ir = <&PIO4 0 ALT2 IN>;
+ };
+ };
+ };
+
+ gmac1 {
+ pinctrl_mii1: mii1 {
+ st,pins {
+ txd0 = <&PIO0 0 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
+ txd1 = <&PIO0 1 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
+ txd2 = <&PIO0 2 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
+ txd3 = <&PIO0 3 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
+ txer = <&PIO0 4 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
+ txen = <&PIO0 5 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
+ txclk = <&PIO0 6 ALT1 IN NICLK 0 CLK_A>;
+ col = <&PIO0 7 ALT1 IN BYPASS 1000>;
+ mdio = <&PIO1 0 ALT1 OUT BYPASS 0>;
+ mdc = <&PIO1 1 ALT1 OUT NICLK 0 CLK_A>;
+ crs = <&PIO1 2 ALT1 IN BYPASS 1000>;
+ mdint = <&PIO1 3 ALT1 IN BYPASS 0>;
+ rxd0 = <&PIO1 4 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+ rxd1 = <&PIO1 5 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+ rxd2 = <&PIO1 6 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+ rxd3 = <&PIO1 7 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+ rxdv = <&PIO2 0 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+ rx_er = <&PIO2 1 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+ rxclk = <&PIO2 2 ALT1 IN NICLK 0 CLK_A>;
+ phyclk = <&PIO2 3 ALT1 IN NICLK 1000 CLK_A>;
+ };
+ };
+
+ pinctrl_rgmii1: rgmii1-0 {
+ st,pins {
+ txd0 = <&PIO0 0 ALT1 OUT DE_IO 1000 CLK_A>;
+ txd1 = <&PIO0 1 ALT1 OUT DE_IO 1000 CLK_A>;
+ txd2 = <&PIO0 2 ALT1 OUT DE_IO 1000 CLK_A>;
+ txd3 = <&PIO0 3 ALT1 OUT DE_IO 1000 CLK_A>;
+ txen = <&PIO0 5 ALT1 OUT DE_IO 0 CLK_A>;
+ txclk = <&PIO0 6 ALT1 IN NICLK 0 CLK_A>;
+ mdio = <&PIO1 0 ALT1 OUT BYPASS 0>;
+ mdc = <&PIO1 1 ALT1 OUT NICLK 0 CLK_A>;
+ rxd0 = <&PIO1 4 ALT1 IN DE_IO 0 CLK_A>;
+ rxd1 = <&PIO1 5 ALT1 IN DE_IO 0 CLK_A>;
+ rxd2 = <&PIO1 6 ALT1 IN DE_IO 0 CLK_A>;
+ rxd3 = <&PIO1 7 ALT1 IN DE_IO 0 CLK_A>;
+
+ rxdv = <&PIO2 0 ALT1 IN DE_IO 500 CLK_A>;
+ rxclk = <&PIO2 2 ALT1 IN NICLK 0 CLK_A>;
+ phyclk = <&PIO2 3 ALT4 OUT NICLK 0 CLK_B>;
+
+ clk125= <&PIO3 7 ALT4 IN NICLK 0 CLK_A>;
+ };
+ };
+ };
};
pin-controller-front {
@@ -111,53 +184,73 @@
#size-cells = <1>;
compatible = "st,stih415-front-pinctrl";
st,syscfg = <&syscfg_front>;
+ reg = <0xfee0f080 0x4>;
+ reg-names = "irqmux";
+ interrupts = <GIC_SPI 181 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts-names = "irqmux";
ranges = <0 0xfee00000 0x8000>;
PIO5: gpio@fee00000 {
gpio-controller;
#gpio-cells = <1>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
reg = <0 0x100>;
st,bank-name = "PIO5";
};
PIO6: gpio@fee01000 {
gpio-controller;
#gpio-cells = <1>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
reg = <0x1000 0x100>;
st,bank-name = "PIO6";
};
PIO7: gpio@fee02000 {
gpio-controller;
#gpio-cells = <1>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
reg = <0x2000 0x100>;
st,bank-name = "PIO7";
};
PIO8: gpio@fee03000 {
gpio-controller;
#gpio-cells = <1>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
reg = <0x3000 0x100>;
st,bank-name = "PIO8";
};
PIO9: gpio@fee04000 {
gpio-controller;
#gpio-cells = <1>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
reg = <0x4000 0x100>;
st,bank-name = "PIO9";
};
PIO10: gpio@fee05000 {
gpio-controller;
#gpio-cells = <1>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
reg = <0x5000 0x100>;
st,bank-name = "PIO10";
};
PIO11: gpio@fee06000 {
gpio-controller;
#gpio-cells = <1>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
reg = <0x6000 0x100>;
st,bank-name = "PIO11";
};
PIO12: gpio@fee07000 {
gpio-controller;
#gpio-cells = <1>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
reg = <0x7000 0x100>;
st,bank-name = "PIO12";
};
@@ -186,41 +279,57 @@
#size-cells = <1>;
compatible = "st,stih415-rear-pinctrl";
st,syscfg = <&syscfg_rear>;
+ reg = <0xfe82f080 0x4>;
+ reg-names = "irqmux";
+ interrupts = <GIC_SPI 182 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts-names = "irqmux";
ranges = <0 0xfe820000 0x8000>;
PIO13: gpio@fe820000 {
gpio-controller;
#gpio-cells = <1>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
reg = <0 0x100>;
st,bank-name = "PIO13";
};
PIO14: gpio@fe821000 {
gpio-controller;
#gpio-cells = <1>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
reg = <0x1000 0x100>;
st,bank-name = "PIO14";
};
PIO15: gpio@fe822000 {
gpio-controller;
#gpio-cells = <1>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
reg = <0x2000 0x100>;
st,bank-name = "PIO15";
};
PIO16: gpio@fe823000 {
gpio-controller;
#gpio-cells = <1>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
reg = <0x3000 0x100>;
st,bank-name = "PIO16";
};
PIO17: gpio@fe824000 {
gpio-controller;
#gpio-cells = <1>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
reg = <0x4000 0x100>;
st,bank-name = "PIO17";
};
PIO18: gpio@fe825000 {
gpio-controller;
#gpio-cells = <1>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
reg = <0x5000 0x100>;
st,bank-name = "PIO18";
};
@@ -233,6 +342,77 @@
};
};
};
+
+ gmac0{
+ pinctrl_mii0: mii0 {
+ st,pins {
+ mdint = <&PIO13 6 ALT2 IN BYPASS 0>;
+ txen = <&PIO13 7 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
+
+ txd0 = <&PIO14 0 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
+ txd1 = <&PIO14 1 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
+ txd2 = <&PIO14 2 ALT2 OUT SE_NICLK_IO 0 CLK_B>;
+ txd3 = <&PIO14 3 ALT2 OUT SE_NICLK_IO 0 CLK_B>;
+
+ txclk = <&PIO15 0 ALT2 IN NICLK 0 CLK_A>;
+ txer = <&PIO15 1 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
+ crs = <&PIO15 2 ALT2 IN BYPASS 1000>;
+ col = <&PIO15 3 ALT2 IN BYPASS 1000>;
+ mdio = <&PIO15 4 ALT2 OUT BYPASS 3000>;
+ mdc = <&PIO15 5 ALT2 OUT NICLK 0 CLK_B>;
+
+ rxd0 = <&PIO16 0 ALT2 IN SE_NICLK_IO 0 CLK_A>;
+ rxd1 = <&PIO16 1 ALT2 IN SE_NICLK_IO 0 CLK_A>;
+ rxd2 = <&PIO16 2 ALT2 IN SE_NICLK_IO 0 CLK_A>;
+ rxd3 = <&PIO16 3 ALT2 IN SE_NICLK_IO 0 CLK_A>;
+ rxdv = <&PIO15 6 ALT2 IN SE_NICLK_IO 0 CLK_A>;
+ rx_er = <&PIO15 7 ALT2 IN SE_NICLK_IO 0 CLK_A>;
+ rxclk = <&PIO17 0 ALT2 IN NICLK 0 CLK_A>;
+ phyclk = <&PIO13 5 ALT2 OUT NICLK 1000 CLK_A>;
+
+ };
+ };
+
+ pinctrl_gmii0: gmii0 {
+ st,pins {
+ mdint = <&PIO13 6 ALT2 IN BYPASS 0>;
+ mdio = <&PIO15 4 ALT2 OUT BYPASS 3000>;
+ mdc = <&PIO15 5 ALT2 OUT NICLK 0 CLK_B>;
+ txen = <&PIO13 7 ALT2 OUT SE_NICLK_IO 3000 CLK_A>;
+
+ txd0 = <&PIO14 0 ALT2 OUT SE_NICLK_IO 3000 CLK_A>;
+ txd1 = <&PIO14 1 ALT2 OUT SE_NICLK_IO 3000 CLK_A>;
+ txd2 = <&PIO14 2 ALT2 OUT SE_NICLK_IO 3000 CLK_B>;
+ txd3 = <&PIO14 3 ALT2 OUT SE_NICLK_IO 3000 CLK_B>;
+ txd4 = <&PIO14 4 ALT2 OUT SE_NICLK_IO 3000 CLK_B>;
+ txd5 = <&PIO14 5 ALT2 OUT SE_NICLK_IO 3000 CLK_B>;
+ txd6 = <&PIO14 6 ALT2 OUT SE_NICLK_IO 3000 CLK_B>;
+ txd7 = <&PIO14 7 ALT2 OUT SE_NICLK_IO 3000 CLK_B>;
+
+ txclk = <&PIO15 0 ALT2 IN NICLK 0 CLK_A>;
+ txer = <&PIO15 1 ALT2 OUT SE_NICLK_IO 3000 CLK_A>;
+ crs = <&PIO15 2 ALT2 IN BYPASS 1000>;
+ col = <&PIO15 3 ALT2 IN BYPASS 1000>;
+ rxdv = <&PIO15 6 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
+ rx_er = <&PIO15 7 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
+
+ rxd0 = <&PIO16 0 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
+ rxd1 = <&PIO16 1 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
+ rxd2 = <&PIO16 2 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
+ rxd3 = <&PIO16 3 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
+ rxd4 = <&PIO16 4 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
+ rxd5 = <&PIO16 5 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
+ rxd6 = <&PIO16 6 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
+ rxd7 = <&PIO16 7 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
+
+ rxclk = <&PIO17 0 ALT2 IN NICLK 0 CLK_A>;
+ clk125 = <&PIO17 6 ALT1 IN NICLK 0 CLK_A>;
+ phyclk = <&PIO13 5 ALT4 OUT NICLK 0 CLK_B>;
+
+
+ };
+ };
+ };
};
pin-controller-left {
@@ -240,23 +420,33 @@
#size-cells = <1>;
compatible = "st,stih415-left-pinctrl";
st,syscfg = <&syscfg_left>;
+ reg = <0xfd6bf080 0x4>;
+ reg-names = "irqmux";
+ interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts-names = "irqmux";
ranges = <0 0xfd6b0000 0x3000>;
PIO100: gpio@fd6b0000 {
gpio-controller;
#gpio-cells = <1>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
reg = <0 0x100>;
st,bank-name = "PIO100";
};
PIO101: gpio@fd6b1000 {
gpio-controller;
#gpio-cells = <1>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
reg = <0x1000 0x100>;
st,bank-name = "PIO101";
};
PIO102: gpio@fd6b2000 {
gpio-controller;
#gpio-cells = <1>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
reg = <0x2000 0x100>;
st,bank-name = "PIO102";
};
@@ -267,35 +457,49 @@
#size-cells = <1>;
compatible = "st,stih415-right-pinctrl";
st,syscfg = <&syscfg_right>;
+ reg = <0xfd33f080 0x4>;
+ reg-names = "irqmux";
+ interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts-names = "irqmux";
ranges = <0 0xfd330000 0x5000>;
PIO103: gpio@fd330000 {
gpio-controller;
#gpio-cells = <1>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
reg = <0 0x100>;
st,bank-name = "PIO103";
};
PIO104: gpio@fd331000 {
gpio-controller;
#gpio-cells = <1>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
reg = <0x1000 0x100>;
st,bank-name = "PIO104";
};
PIO105: gpio@fd332000 {
gpio-controller;
#gpio-cells = <1>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
reg = <0x2000 0x100>;
st,bank-name = "PIO105";
};
PIO106: gpio@fd333000 {
gpio-controller;
#gpio-cells = <1>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
reg = <0x3000 0x100>;
st,bank-name = "PIO106";
};
PIO107: gpio@fd334000 {
gpio-controller;
#gpio-cells = <1>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
reg = <0x4000 0x100>;
st,bank-name = "PIO107";
};
diff --git a/arch/arm/boot/dts/stih415.dtsi b/arch/arm/boot/dts/stih415.dtsi
index d9c7dd1..d89064c 100644
--- a/arch/arm/boot/dts/stih415.dtsi
+++ b/arch/arm/boot/dts/stih415.dtsi
@@ -10,6 +10,7 @@
#include "stih415-clock.dtsi"
#include "stih415-pinctrl.dtsi"
#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/reset-controller/stih415-resets.h>
/ {
L2: cache-controller {
@@ -28,6 +29,16 @@
ranges;
compatible = "simple-bus";
+ powerdown: powerdown-controller {
+ #reset-cells = <1>;
+ compatible = "st,stih415-powerdown";
+ };
+
+ softreset: softreset-controller {
+ #reset-cells = <1>;
+ compatible = "st,stih415-softreset";
+ };
+
syscfg_sbc: sbc-syscfg@fe600000{
compatible = "st,stih415-sbc-syscfg", "syscon";
reg = <0xfe600000 0xb4>;
@@ -136,5 +147,64 @@
status = "disabled";
};
+
+ ethernet0: dwmac@fe810000 {
+ device_type = "network";
+ compatible = "st,stih415-dwmac", "snps,dwmac", "snps,dwmac-3.610";
+ status = "disabled";
+
+ reg = <0xfe810000 0x8000>, <0x148 0x4>;
+ reg-names = "stmmaceth", "sti-ethconf";
+
+ interrupts = <0 147 0>, <0 148 0>, <0 149 0>;
+ interrupt-names = "macirq", "eth_wake_irq", "eth_lpi";
+ resets = <&softreset STIH415_ETH0_SOFTRESET>;
+ reset-names = "stmmaceth";
+
+ snps,pbl = <32>;
+ snps,mixed-burst;
+ snps,force_sf_dma_mode;
+
+ st,syscon = <&syscfg_rear>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_mii0>;
+ clock-names = "stmmaceth";
+ clocks = <&CLKS_GMAC0_PHY>;
+ };
+
+ ethernet1: dwmac@fef08000 {
+ device_type = "network";
+ compatible = "st,stih415-dwmac", "snps,dwmac", "snps,dwmac-3.610";
+ status = "disabled";
+ reg = <0xfef08000 0x8000>, <0x74 0x4>;
+ reg-names = "stmmaceth", "sti-ethconf";
+ interrupts = <0 150 0>, <0 151 0>, <0 152 0>;
+ interrupt-names = "macirq", "eth_wake_irq", "eth_lpi";
+
+ snps,pbl = <32>;
+ snps,mixed-burst;
+ snps,force_sf_dma_mode;
+
+ st,syscon = <&syscfg_sbc>;
+
+ resets = <&softreset STIH415_ETH1_SOFTRESET>;
+ reset-names = "stmmaceth";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_mii1>;
+ clock-names = "stmmaceth";
+ clocks = <&CLKS_ETH1_PHY>;
+ };
+
+ rc: rc@fe518000 {
+ compatible = "st,comms-irb";
+ reg = <0xfe518000 0x234>;
+ interrupts = <0 203 0>;
+ clocks = <&CLK_SYSIN>;
+ rx-mode = "infrared";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ir>;
+ resets = <&softreset STIH415_IRB_SOFTRESET>;
+ };
};
};
diff --git a/arch/arm/boot/dts/stih416-clock.dtsi b/arch/arm/boot/dts/stih416-clock.dtsi
index 7026bf1..a6942c7 100644
--- a/arch/arm/boot/dts/stih416-clock.dtsi
+++ b/arch/arm/boot/dts/stih416-clock.dtsi
@@ -37,5 +37,19 @@
clock-frequency = <100000000>;
clock-output-names = "CLK_S_ICN_REG_0";
};
+
+ CLK_S_GMAC0_PHY: clockgenA1@7 {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <25000000>;
+ clock-output-names = "CLK_S_GMAC0_PHY";
+ };
+
+ CLK_S_ETH1_PHY: clockgenA0@7 {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <25000000>;
+ clock-output-names = "CLK_S_ETH1_PHY";
+ };
};
};
diff --git a/arch/arm/boot/dts/stih416-pinctrl.dtsi b/arch/arm/boot/dts/stih416-pinctrl.dtsi
index b29ff4b..e7f8b5f 100644
--- a/arch/arm/boot/dts/stih416-pinctrl.dtsi
+++ b/arch/arm/boot/dts/stih416-pinctrl.dtsi
@@ -8,6 +8,7 @@
* publishhed by the Free Software Foundation.
*/
#include "st-pincfg.h"
+#include <dt-bindings/interrupt-controller/arm-gic.h>
/ {
aliases {
@@ -49,46 +50,69 @@
#size-cells = <1>;
compatible = "st,stih416-sbc-pinctrl";
st,syscfg = <&syscfg_sbc>;
+ reg = <0xfe61f080 0x4>;
+ reg-names = "irqmux";
+ interrupts = <GIC_SPI 182 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts-names = "irqmux";
ranges = <0 0xfe610000 0x6000>;
PIO0: gpio@fe610000 {
gpio-controller;
#gpio-cells = <1>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
reg = <0 0x100>;
st,bank-name = "PIO0";
};
PIO1: gpio@fe611000 {
gpio-controller;
#gpio-cells = <1>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
reg = <0x1000 0x100>;
st,bank-name = "PIO1";
};
PIO2: gpio@fe612000 {
gpio-controller;
#gpio-cells = <1>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
reg = <0x2000 0x100>;
st,bank-name = "PIO2";
};
PIO3: gpio@fe613000 {
gpio-controller;
#gpio-cells = <1>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
reg = <0x3000 0x100>;
st,bank-name = "PIO3";
};
PIO4: gpio@fe614000 {
gpio-controller;
#gpio-cells = <1>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
reg = <0x4000 0x100>;
st,bank-name = "PIO4";
};
PIO40: gpio@fe615000 {
gpio-controller;
#gpio-cells = <1>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
reg = <0x5000 0x100>;
st,bank-name = "PIO40";
st,retime-pin-mask = <0x7f>;
};
+ rc{
+ pinctrl_ir: ir0 {
+ st,pins {
+ ir = <&PIO4 0 ALT2 IN>;
+ };
+ };
+ };
sbc_serial1 {
pinctrl_sbc_serial1: sbc_serial1 {
st,pins {
@@ -115,6 +139,58 @@
};
};
};
+
+ gmac1 {
+ pinctrl_mii1: mii1 {
+ st,pins {
+ txd0 = <&PIO0 0 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
+ txd1 = <&PIO0 1 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
+ txd2 = <&PIO0 2 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
+ txd3 = <&PIO0 3 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
+ txer = <&PIO0 4 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
+ txen = <&PIO0 5 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
+ txclk = <&PIO0 6 ALT1 IN NICLK 0 CLK_A>;
+ col = <&PIO0 7 ALT1 IN BYPASS 1000>;
+
+ mdio = <&PIO1 0 ALT1 OUT BYPASS 1500>;
+ mdc = <&PIO1 1 ALT1 OUT NICLK 0 CLK_A>;
+ crs = <&PIO1 2 ALT1 IN BYPASS 1000>;
+ mdint = <&PIO1 3 ALT1 IN BYPASS 0>;
+ rxd0 = <&PIO1 4 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+ rxd1 = <&PIO1 5 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+ rxd2 = <&PIO1 6 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+ rxd3 = <&PIO1 7 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+
+ rxdv = <&PIO2 0 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+ rx_er = <&PIO2 1 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+ rxclk = <&PIO2 2 ALT1 IN NICLK 0 CLK_A>;
+ phyclk = <&PIO2 3 ALT1 OUT NICLK 0 CLK_A>;
+ };
+ };
+ pinctrl_rgmii1: rgmii1-0 {
+ st,pins {
+ txd0 = <&PIO0 0 ALT1 OUT DE_IO 500 CLK_A>;
+ txd1 = <&PIO0 1 ALT1 OUT DE_IO 500 CLK_A>;
+ txd2 = <&PIO0 2 ALT1 OUT DE_IO 500 CLK_A>;
+ txd3 = <&PIO0 3 ALT1 OUT DE_IO 500 CLK_A>;
+ txen = <&PIO0 5 ALT1 OUT DE_IO 0 CLK_A>;
+ txclk = <&PIO0 6 ALT1 IN NICLK 0 CLK_A>;
+
+ mdio = <&PIO1 0 ALT1 OUT BYPASS 0>;
+ mdc = <&PIO1 1 ALT1 OUT NICLK 0 CLK_A>;
+ rxd0 = <&PIO1 4 ALT1 IN DE_IO 500 CLK_A>;
+ rxd1 = <&PIO1 5 ALT1 IN DE_IO 500 CLK_A>;
+ rxd2 = <&PIO1 6 ALT1 IN DE_IO 500 CLK_A>;
+ rxd3 = <&PIO1 7 ALT1 IN DE_IO 500 CLK_A>;
+
+ rxdv = <&PIO2 0 ALT1 IN DE_IO 500 CLK_A>;
+ rxclk = <&PIO2 2 ALT1 IN NICLK 0 CLK_A>;
+ phyclk = <&PIO2 3 ALT4 OUT NICLK 0 CLK_B>;
+
+ clk125= <&PIO3 7 ALT4 IN NICLK 0 CLK_A>;
+ };
+ };
+ };
};
pin-controller-front {
@@ -122,65 +198,89 @@
#size-cells = <1>;
compatible = "st,stih416-front-pinctrl";
st,syscfg = <&syscfg_front>;
+ reg = <0xfee0f080 0x4>;
+ reg-names = "irqmux";
+ interrupts = <GIC_SPI 183 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts-names = "irqmux";
ranges = <0 0xfee00000 0x10000>;
PIO5: gpio@fee00000 {
gpio-controller;
#gpio-cells = <1>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
reg = <0 0x100>;
st,bank-name = "PIO5";
};
PIO6: gpio@fee01000 {
gpio-controller;
#gpio-cells = <1>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
reg = <0x1000 0x100>;
st,bank-name = "PIO6";
};
PIO7: gpio@fee02000 {
gpio-controller;
#gpio-cells = <1>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
reg = <0x2000 0x100>;
st,bank-name = "PIO7";
};
PIO8: gpio@fee03000 {
gpio-controller;
#gpio-cells = <1>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
reg = <0x3000 0x100>;
st,bank-name = "PIO8";
};
PIO9: gpio@fee04000 {
gpio-controller;
#gpio-cells = <1>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
reg = <0x4000 0x100>;
st,bank-name = "PIO9";
};
PIO10: gpio@fee05000 {
gpio-controller;
#gpio-cells = <1>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
reg = <0x5000 0x100>;
st,bank-name = "PIO10";
};
PIO11: gpio@fee06000 {
gpio-controller;
#gpio-cells = <1>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
reg = <0x6000 0x100>;
st,bank-name = "PIO11";
};
PIO12: gpio@fee07000 {
gpio-controller;
#gpio-cells = <1>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
reg = <0x7000 0x100>;
st,bank-name = "PIO12";
};
PIO30: gpio@fee08000 {
gpio-controller;
#gpio-cells = <1>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
reg = <0x8000 0x100>;
st,bank-name = "PIO30";
};
PIO31: gpio@fee09000 {
gpio-controller;
#gpio-cells = <1>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
reg = <0x9000 0x100>;
st,bank-name = "PIO31";
};
@@ -217,41 +317,57 @@
#size-cells = <1>;
compatible = "st,stih416-rear-pinctrl";
st,syscfg = <&syscfg_rear>;
+ reg = <0xfe82f080 0x4>;
+ reg-names = "irqmux";
+ interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts-names = "irqmux";
ranges = <0 0xfe820000 0x6000>;
PIO13: gpio@fe820000 {
gpio-controller;
#gpio-cells = <1>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
reg = <0 0x100>;
st,bank-name = "PIO13";
};
PIO14: gpio@fe821000 {
gpio-controller;
#gpio-cells = <1>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
reg = <0x1000 0x100>;
st,bank-name = "PIO14";
};
PIO15: gpio@fe822000 {
gpio-controller;
#gpio-cells = <1>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
reg = <0x2000 0x100>;
st,bank-name = "PIO15";
};
PIO16: gpio@fe823000 {
gpio-controller;
#gpio-cells = <1>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
reg = <0x3000 0x100>;
st,bank-name = "PIO16";
};
PIO17: gpio@fe824000 {
gpio-controller;
#gpio-cells = <1>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
reg = <0x4000 0x100>;
st,bank-name = "PIO17";
};
PIO18: gpio@fe825000 {
gpio-controller;
#gpio-cells = <1>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
reg = <0x5000 0x100>;
st,bank-name = "PIO18";
st,retime-pin-mask = <0xf>;
@@ -265,6 +381,63 @@
};
};
};
+
+ gmac0 {
+ pinctrl_mii0: mii0 {
+ st,pins {
+ mdint = <&PIO13 6 ALT2 IN BYPASS 0>;
+ txen = <&PIO13 7 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
+ txd0 = <&PIO14 0 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
+ txd1 = <&PIO14 1 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
+ txd2 = <&PIO14 2 ALT2 OUT SE_NICLK_IO 0 CLK_B>;
+ txd3 = <&PIO14 3 ALT2 OUT SE_NICLK_IO 0 CLK_B>;
+
+ txclk = <&PIO15 0 ALT2 IN NICLK 0 CLK_A>;
+ txer = <&PIO15 1 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
+ crs = <&PIO15 2 ALT2 IN BYPASS 1000>;
+ col = <&PIO15 3 ALT2 IN BYPASS 1000>;
+ mdio= <&PIO15 4 ALT2 OUT BYPASS 1500>;
+ mdc = <&PIO15 5 ALT2 OUT NICLK 0 CLK_B>;
+
+ rxd0 = <&PIO16 0 ALT2 IN SE_NICLK_IO 0 CLK_A>;
+ rxd1 = <&PIO16 1 ALT2 IN SE_NICLK_IO 0 CLK_A>;
+ rxd2 = <&PIO16 2 ALT2 IN SE_NICLK_IO 0 CLK_A>;
+ rxd3 = <&PIO16 3 ALT2 IN SE_NICLK_IO 0 CLK_A>;
+ rxdv = <&PIO15 6 ALT2 IN SE_NICLK_IO 0 CLK_A>;
+ rx_er = <&PIO15 7 ALT2 IN SE_NICLK_IO 0 CLK_A>;
+ rxclk = <&PIO17 0 ALT2 IN NICLK 0 CLK_A>;
+ phyclk = <&PIO13 5 ALT2 OUT NICLK 0 CLK_B>;
+ };
+ };
+
+ pinctrl_gmii0: gmii0 {
+ st,pins {
+ };
+ };
+ pinctrl_rgmii0: rgmii0 {
+ st,pins {
+ phyclk = <&PIO13 5 ALT4 OUT NICLK 0 CLK_B>;
+ txen = <&PIO13 7 ALT2 OUT DE_IO 0 CLK_A>;
+ txd0 = <&PIO14 0 ALT2 OUT DE_IO 500 CLK_A>;
+ txd1 = <&PIO14 1 ALT2 OUT DE_IO 500 CLK_A>;
+ txd2 = <&PIO14 2 ALT2 OUT DE_IO 500 CLK_B>;
+ txd3 = <&PIO14 3 ALT2 OUT DE_IO 500 CLK_B>;
+ txclk = <&PIO15 0 ALT2 IN NICLK 0 CLK_A>;
+
+ mdio = <&PIO15 4 ALT2 OUT BYPASS 0>;
+ mdc = <&PIO15 5 ALT2 OUT NICLK 0 CLK_B>;
+
+ rxdv = <&PIO15 6 ALT2 IN DE_IO 500 CLK_A>;
+ rxd0 =<&PIO16 0 ALT2 IN DE_IO 500 CLK_A>;
+ rxd1 =<&PIO16 1 ALT2 IN DE_IO 500 CLK_A>;
+ rxd2 =<&PIO16 2 ALT2 IN DE_IO 500 CLK_A>;
+ rxd3 =<&PIO16 3 ALT2 IN DE_IO 500 CLK_A>;
+ rxclk =<&PIO17 0 ALT2 IN NICLK 0 CLK_A>;
+
+ clk125=<&PIO17 6 ALT1 IN NICLK 0 CLK_A>;
+ };
+ };
+ };
};
pin-controller-fvdp-fe {
@@ -272,23 +445,33 @@
#size-cells = <1>;
compatible = "st,stih416-fvdp-fe-pinctrl";
st,syscfg = <&syscfg_fvdp_fe>;
+ reg = <0xfd6bf080 0x4>;
+ reg-names = "irqmux";
+ interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts-names = "irqmux";
ranges = <0 0xfd6b0000 0x3000>;
PIO100: gpio@fd6b0000 {
gpio-controller;
#gpio-cells = <1>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
reg = <0 0x100>;
st,bank-name = "PIO100";
};
PIO101: gpio@fd6b1000 {
gpio-controller;
#gpio-cells = <1>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
reg = <0x1000 0x100>;
st,bank-name = "PIO101";
};
PIO102: gpio@fd6b2000 {
gpio-controller;
#gpio-cells = <1>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
reg = <0x2000 0x100>;
st,bank-name = "PIO102";
};
@@ -299,29 +482,41 @@
#size-cells = <1>;
compatible = "st,stih416-fvdp-lite-pinctrl";
st,syscfg = <&syscfg_fvdp_lite>;
+ reg = <0xfd33f080 0x4>;
+ reg-names = "irqmux";
+ interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts-names = "irqmux";
ranges = <0 0xfd330000 0x5000>;
PIO103: gpio@fd330000 {
gpio-controller;
#gpio-cells = <1>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
reg = <0 0x100>;
st,bank-name = "PIO103";
};
PIO104: gpio@fd331000 {
gpio-controller;
#gpio-cells = <1>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
reg = <0x1000 0x100>;
st,bank-name = "PIO104";
};
PIO105: gpio@fd332000 {
gpio-controller;
#gpio-cells = <1>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
reg = <0x2000 0x100>;
st,bank-name = "PIO105";
};
PIO106: gpio@fd333000 {
gpio-controller;
#gpio-cells = <1>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
reg = <0x3000 0x100>;
st,bank-name = "PIO106";
};
@@ -329,6 +524,8 @@
PIO107: gpio@fd334000 {
gpio-controller;
#gpio-cells = <1>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
reg = <0x4000 0x100>;
st,bank-name = "PIO107";
st,retime-pin-mask = <0xf>;
diff --git a/arch/arm/boot/dts/stih416.dtsi b/arch/arm/boot/dts/stih416.dtsi
index b7ab47b..8299a7b 100644
--- a/arch/arm/boot/dts/stih416.dtsi
+++ b/arch/arm/boot/dts/stih416.dtsi
@@ -10,6 +10,7 @@
#include "stih416-clock.dtsi"
#include "stih416-pinctrl.dtsi"
#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/reset-controller/stih416-resets.h>
/ {
L2: cache-controller {
compatible = "arm,pl310-cache";
@@ -27,6 +28,16 @@
ranges;
compatible = "simple-bus";
+ powerdown: powerdown-controller {
+ #reset-cells = <1>;
+ compatible = "st,stih416-powerdown";
+ };
+
+ softreset: softreset-controller {
+ #reset-cells = <1>;
+ compatible = "st,stih416-softreset";
+ };
+
syscfg_sbc:sbc-syscfg@fe600000{
compatible = "st,stih416-sbc-syscfg", "syscon";
reg = <0xfe600000 0x1000>;
@@ -145,5 +156,61 @@
status = "disabled";
};
+
+ ethernet0: dwmac@fe810000 {
+ device_type = "network";
+ compatible = "st,stih416-dwmac", "snps,dwmac", "snps,dwmac-3.710";
+ status = "disabled";
+ reg = <0xfe810000 0x8000>, <0x8bc 0x4>;
+ reg-names = "stmmaceth", "sti-ethconf";
+
+ interrupts = <0 133 0>, <0 134 0>, <0 135 0>;
+ interrupt-names = "macirq", "eth_wake_irq", "eth_lpi";
+
+ snps,pbl = <32>;
+ snps,mixed-burst;
+
+ st,syscon = <&syscfg_rear>;
+ resets = <&softreset STIH416_ETH0_SOFTRESET>;
+ reset-names = "stmmaceth";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_mii0>;
+ clock-names = "stmmaceth";
+ clocks = <&CLK_S_GMAC0_PHY>;
+ };
+
+ ethernet1: dwmac@fef08000 {
+ device_type = "network";
+ compatible = "st,stih416-dwmac", "snps,dwmac", "snps,dwmac-3.710";
+ status = "disabled";
+ reg = <0xfef08000 0x8000>, <0x7f0 0x4>;
+ reg-names = "stmmaceth", "sti-ethconf";
+ interrupts = <0 136 0>, <0 137 0>, <0 138 0>;
+ interrupt-names = "macirq", "eth_wake_irq", "eth_lpi";
+
+ snps,pbl = <32>;
+ snps,mixed-burst;
+
+ st,syscon = <&syscfg_sbc>;
+
+ resets = <&softreset STIH416_ETH1_SOFTRESET>;
+ reset-names = "stmmaceth";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_mii1>;
+ clock-names = "stmmaceth";
+ clocks = <&CLK_S_ETH1_PHY>;
+ };
+
+ rc: rc@fe518000 {
+ compatible = "st,comms-irb";
+ reg = <0xfe518000 0x234>;
+ interrupts = <0 203 0>;
+ rx-mode = "infrared";
+ clocks = <&CLK_SYSIN>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ir>;
+ resets = <&softreset STIH416_IRB_SOFTRESET>;
+ };
+
};
};
diff --git a/arch/arm/boot/dts/stih41x-b2000.dtsi b/arch/arm/boot/dts/stih41x-b2000.dtsi
index 1e6aa92..bf65c49 100644
--- a/arch/arm/boot/dts/stih41x-b2000.dtsi
+++ b/arch/arm/boot/dts/stih41x-b2000.dtsi
@@ -20,6 +20,8 @@
aliases {
ttyAS0 = &serial2;
+ ethernet0 = &ethernet0;
+ ethernet1 = &ethernet1;
};
soc {
@@ -46,5 +48,25 @@
status = "okay";
};
+
+ ethernet0: dwmac@fe810000 {
+ status = "okay";
+ phy-mode = "mii";
+ pinctrl-0 = <&pinctrl_mii0>;
+
+ snps,reset-gpio = <&PIO106 2>;
+ snps,reset-active-low;
+ snps,reset-delays-us = <0 10000 10000>;
+ };
+
+ ethernet1: dwmac@fef08000 {
+ status = "disabled";
+ phy-mode = "mii";
+ st,tx-retime-src = "txclk";
+
+ snps,reset-gpio = <&PIO4 7>;
+ snps,reset-active-low;
+ snps,reset-delays-us = <0 10000 10000>;
+ };
};
};
diff --git a/arch/arm/boot/dts/stih41x-b2020.dtsi b/arch/arm/boot/dts/stih41x-b2020.dtsi
index 0ef0a69..3dc74c2 100644
--- a/arch/arm/boot/dts/stih41x-b2020.dtsi
+++ b/arch/arm/boot/dts/stih41x-b2020.dtsi
@@ -19,6 +19,7 @@
aliases {
ttyAS0 = &sbc_serial1;
+ ethernet1 = &ethernet1;
};
soc {
sbc_serial1: serial@fe531000 {
@@ -60,5 +61,17 @@
i2c@fe541000 {
status = "okay";
};
+
+ ethernet1: dwmac@fef08000 {
+ status = "okay";
+ phy-mode = "rgmii-id";
+ max-speed = <1000>;
+ st,tx-retime-src = "clk_125";
+ snps,reset-gpio = <&PIO3 0>;
+ snps,reset-active-low;
+ snps,reset-delays-us = <0 10000 10000>;
+
+ pinctrl-0 = <&pinctrl_rgmii1>;
+ };
};
};
diff --git a/include/dt-bindings/reset-controller/stih415-resets.h b/include/dt-bindings/reset-controller/stih415-resets.h
new file mode 100644
index 0000000..c2f8a66
--- /dev/null
+++ b/include/dt-bindings/reset-controller/stih415-resets.h
@@ -0,0 +1,26 @@
+/*
+ * This header provides constants for the reset controller
+ * based peripheral powerdown requests on the STMicroelectronics
+ * STiH415 SoC.
+ */
+#ifndef _DT_BINDINGS_RESET_CONTROLLER_STIH415
+#define _DT_BINDINGS_RESET_CONTROLLER_STIH415
+
+#define STIH415_EMISS_POWERDOWN 0
+#define STIH415_NAND_POWERDOWN 1
+#define STIH415_KEYSCAN_POWERDOWN 2
+#define STIH415_USB0_POWERDOWN 3
+#define STIH415_USB1_POWERDOWN 4
+#define STIH415_USB2_POWERDOWN 5
+#define STIH415_SATA0_POWERDOWN 6
+#define STIH415_SATA1_POWERDOWN 7
+#define STIH415_PCIE_POWERDOWN 8
+
+#define STIH415_ETH0_SOFTRESET 0
+#define STIH415_ETH1_SOFTRESET 1
+#define STIH415_IRB_SOFTRESET 2
+#define STIH415_USB0_SOFTRESET 3
+#define STIH415_USB1_SOFTRESET 4
+#define STIH415_USB2_SOFTRESET 5
+
+#endif /* _DT_BINDINGS_RESET_CONTROLLER_STIH415 */
diff --git a/include/dt-bindings/reset-controller/stih416-resets.h b/include/dt-bindings/reset-controller/stih416-resets.h
new file mode 100644
index 0000000..2127743
--- /dev/null
+++ b/include/dt-bindings/reset-controller/stih416-resets.h
@@ -0,0 +1,50 @@
+/*
+ * This header provides constants for the reset controller
+ * based peripheral powerdown requests on the STMicroelectronics
+ * STiH416 SoC.
+ */
+#ifndef _DT_BINDINGS_RESET_CONTROLLER_STIH416
+#define _DT_BINDINGS_RESET_CONTROLLER_STIH416
+
+#define STIH416_EMISS_POWERDOWN 0
+#define STIH416_NAND_POWERDOWN 1
+#define STIH416_KEYSCAN_POWERDOWN 2
+#define STIH416_USB0_POWERDOWN 3
+#define STIH416_USB1_POWERDOWN 4
+#define STIH416_USB2_POWERDOWN 5
+#define STIH416_USB3_POWERDOWN 6
+#define STIH416_SATA0_POWERDOWN 7
+#define STIH416_SATA1_POWERDOWN 8
+#define STIH416_PCIE0_POWERDOWN 9
+#define STIH416_PCIE1_POWERDOWN 10
+
+#define STIH416_ETH0_SOFTRESET 0
+#define STIH416_ETH1_SOFTRESET 1
+#define STIH416_IRB_SOFTRESET 2
+#define STIH416_USB0_SOFTRESET 3
+#define STIH416_USB1_SOFTRESET 4
+#define STIH416_USB2_SOFTRESET 5
+#define STIH416_USB3_SOFTRESET 6
+#define STIH416_SATA0_SOFTRESET 7
+#define STIH416_SATA1_SOFTRESET 8
+#define STIH416_PCIE0_SOFTRESET 9
+#define STIH416_PCIE1_SOFTRESET 10
+#define STIH416_AUD_DAC_SOFTRESET 11
+#define STIH416_HDTVOUT_SOFTRESET 12
+#define STIH416_VTAC_M_RX_SOFTRESET 13
+#define STIH416_VTAC_A_RX_SOFTRESET 14
+#define STIH416_SYNC_HD_SOFTRESET 15
+#define STIH416_SYNC_SD_SOFTRESET 16
+#define STIH416_BLITTER_SOFTRESET 17
+#define STIH416_GPU_SOFTRESET 18
+#define STIH416_VTAC_M_TX_SOFTRESET 19
+#define STIH416_VTAC_A_TX_SOFTRESET 20
+#define STIH416_VTG_AUX_SOFTRESET 21
+#define STIH416_JPEG_DEC_SOFTRESET 22
+#define STIH416_HVA_SOFTRESET 23
+#define STIH416_COMPO_M_SOFTRESET 24
+#define STIH416_COMPO_A_SOFTRESET 25
+#define STIH416_VP8_DEC_SOFTRESET 26
+#define STIH416_VTG_MAIN_SOFTRESET 27
+
+#endif /* _DT_BINDINGS_RESET_CONTROLLER_STIH416 */
generated by cgit v0.10.2 at 2024-11-08 09:35:09 (GMT)