diff options
| -rw-r--r-- | Documentation/devicetree/bindings/serial/of-serial.txt | 1 | ||||
| -rw-r--r-- | drivers/tty/serial/8250/8250_core.c | 6 | ||||
| -rw-r--r-- | drivers/tty/serial/of_serial.c | 4 | ||||
| -rw-r--r-- | drivers/tty/serial/serial_core.c | 12 |
4 files changed, 5 insertions, 18 deletions
diff --git a/Documentation/devicetree/bindings/serial/of-serial.txt b/Documentation/devicetree/bindings/serial/of-serial.txt index 7705477..1928a3e 100644 --- a/Documentation/devicetree/bindings/serial/of-serial.txt +++ b/Documentation/devicetree/bindings/serial/of-serial.txt @@ -37,7 +37,6 @@ Optional properties: - auto-flow-control: one way to enable automatic flow control support. The driver is allowed to detect support for the capability even without this property. -- has-hw-flow-control: the hardware has flow control capability. Example: diff --git a/drivers/tty/serial/8250/8250_core.c b/drivers/tty/serial/8250/8250_core.c index b28ed1b..46c1f5f 100644 --- a/drivers/tty/serial/8250/8250_core.c +++ b/drivers/tty/serial/8250/8250_core.c @@ -2319,11 +2319,9 @@ serial8250_do_set_termios(struct uart_port *port, struct ktermios *termios, * the trigger, or the MCR RTS bit is cleared. In the case where * the remote UART is not using CTS auto flow control, we must * have sufficient FIFO entries for the latency of the remote - * UART to respond. IOW, at least 32 bytes of FIFO. Also enable - * AFE if hw flow control is supported + * UART to respond. IOW, at least 32 bytes of FIFO. */ - if ((up->capabilities & UART_CAP_AFE && (port->fifosize >= 32)) || - (port->flags & UPF_HARD_FLOW)) { + if (up->capabilities & UART_CAP_AFE && port->fifosize >= 32) { up->mcr &= ~UART_MCR_AFE; if (termios->c_cflag & CRTSCTS) up->mcr |= UART_MCR_AFE; diff --git a/drivers/tty/serial/of_serial.c b/drivers/tty/serial/of_serial.c index 68d4455..27981e2 100644 --- a/drivers/tty/serial/of_serial.c +++ b/drivers/tty/serial/of_serial.c @@ -183,10 +183,6 @@ static int of_platform_serial_probe(struct platform_device *ofdev) "auto-flow-control")) port8250.capabilities |= UART_CAP_AFE; - if (of_property_read_bool(ofdev->dev.of_node, - "has-hw-flow-control")) - port8250.port.flags |= UPF_HARD_FLOW; - ret = serial8250_register_8250_port(&port8250); break; } diff --git a/drivers/tty/serial/serial_core.c b/drivers/tty/serial/serial_core.c index 079f18d..2e57d5b 100644 --- a/drivers/tty/serial/serial_core.c +++ b/drivers/tty/serial/serial_core.c @@ -175,12 +175,8 @@ static int uart_port_startup(struct tty_struct *tty, struct uart_state *state, if (tty->termios.c_cflag & CBAUD) uart_set_mctrl(uport, TIOCM_RTS | TIOCM_DTR); } - /* - * if hw support flow control without software intervention, - * then skip the below check - */ - if (tty_port_cts_enabled(port) && - !(uport->flags & UPF_HARD_FLOW)) { + + if (tty_port_cts_enabled(port)) { spin_lock_irq(&uport->lock); if (!(uport->ops->get_mctrl(uport) & TIOCM_CTS)) tty->hw_stopped = 1; @@ -2789,9 +2785,7 @@ void uart_handle_cts_change(struct uart_port *uport, unsigned int status) uport->icount.cts++; - /* skip below code if the hw flow control is supported */ - if (tty_port_cts_enabled(port) && - !(uport->flags & UPF_HARD_FLOW)) { + if (tty_port_cts_enabled(port)) { if (tty->hw_stopped) { if (status) { tty->hw_stopped = 0; |