summaryrefslogtreecommitdiff
diff options
context:
space:
mode:
Diffstat
-rw-r--r--arch/arm/boot/dts/Makefile2
-rw-r--r--arch/arm/boot/dts/dove-cubox.dts30
-rw-r--r--arch/arm/boot/dts/dove-d2plug.dts69
-rw-r--r--arch/arm/boot/dts/dove.dtsi233
-rw-r--r--arch/arm/boot/dts/kirkwood-mv88f6281gtw-ge.dts125
-rw-r--r--arch/arm/configs/kirkwood_defconfig18
-rw-r--r--arch/arm/mach-kirkwood/Kconfig66
-rw-r--r--arch/arm/mach-kirkwood/Makefile10
-rw-r--r--arch/arm/mach-kirkwood/board-dnskw.c36
-rw-r--r--arch/arm/mach-kirkwood/board-dt.c4
-rw-r--r--arch/arm/mach-kirkwood/board-mv88f6281gtw_ge.c50
-rw-r--r--arch/arm/mach-kirkwood/common.h6
-rw-r--r--arch/arm/mach-kirkwood/dockstar-setup.c111
-rw-r--r--arch/arm/mach-kirkwood/guruplug-setup.c133
-rw-r--r--arch/arm/mach-kirkwood/mv88f6281gtw_ge-setup.c172
-rw-r--r--arch/arm/mach-kirkwood/netspace_v2-setup.c293
-rw-r--r--arch/arm/mach-kirkwood/openrd-setup.c3
-rw-r--r--arch/arm/mach-kirkwood/rd88f6281-setup.c4
-rw-r--r--arch/arm/mach-kirkwood/sheevaplug-setup.c161
19 files changed, 490 insertions, 1036 deletions
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index af19e38..4865266 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -47,6 +47,7 @@ dtb-$(CONFIG_ARCH_DAVINCI) += da850-enbw-cmc.dtb \
da850-evm.dtb
dtb-$(CONFIG_ARCH_DOVE) += dove-cm-a510.dtb \
dove-cubox.dtb \
+ dove-d2plug.dtb \
dove-dove-db.dtb
dtb-$(CONFIG_ARCH_EXYNOS) += exynos4210-origen.dtb \
exynos4210-smdkv310.dtb \
@@ -83,6 +84,7 @@ dtb-$(CONFIG_ARCH_KIRKWOOD) += kirkwood-cloudbox.dtb \
kirkwood-lschlv2.dtb \
kirkwood-lsxhl.dtb \
kirkwood-mplcec4.dtb \
+ kirkwood-mv88f6281gtw-ge.dtb \
kirkwood-netgear_readynas_duo_v2.dtb \
kirkwood-ns2.dtb \
kirkwood-ns2lite.dtb \
diff --git a/arch/arm/boot/dts/dove-cubox.dts b/arch/arm/boot/dts/dove-cubox.dts
index 955188f..022646e 100644
--- a/arch/arm/boot/dts/dove-cubox.dts
+++ b/arch/arm/boot/dts/dove-cubox.dts
@@ -42,6 +42,8 @@
regulator-always-on;
regulator-boot-on;
gpio = <&gpio0 1 0>;
+ pinctrl-0 = <&pmx_gpio_1>;
+ pinctrl-names = "default";
};
};
@@ -53,6 +55,13 @@
clock-frequency = <25000000>;
};
};
+
+ ir_recv: ir-receiver {
+ compatible = "gpio-ir-receiver";
+ gpios = <&gpio0 19 1>;
+ pinctrl-0 = <&pmx_gpio_19>;
+ pinctrl-names = "default";
+ };
};
&uart0 { status = "okay"; };
@@ -110,6 +119,7 @@
status = "okay";
/* sdio0 card detect is connected to wrong pin on CuBox */
cd-gpios = <&gpio0 12 1>;
+ pinctrl-0 = <&pmx_sdio0 &pmx_gpio_12>;
};
&spi0 {
@@ -122,23 +132,3 @@
reg = <0>;
};
};
-
-&pinctrl {
- pinctrl-0 = <&pmx_gpio_1 &pmx_gpio_12>;
- pinctrl-names = "default";
-
- pmx_gpio_1: pmx-gpio-1 {
- marvell,pins = "mpp1";
- marvell,function = "gpio";
- };
-
- pmx_gpio_12: pmx-gpio-12 {
- marvell,pins = "mpp12";
- marvell,function = "gpio";
- };
-
- pmx_gpio_18: pmx-gpio-18 {
- marvell,pins = "mpp18";
- marvell,function = "gpio";
- };
-};
diff --git a/arch/arm/boot/dts/dove-d2plug.dts b/arch/arm/boot/dts/dove-d2plug.dts
new file mode 100644
index 0000000..e2222ce
--- /dev/null
+++ b/arch/arm/boot/dts/dove-d2plug.dts
@@ -0,0 +1,69 @@
+/dts-v1/;
+
+/include/ "dove.dtsi"
+
+/ {
+ model = "Globalscale D2Plug";
+ compatible = "globalscale,d2plug", "marvell,dove";
+
+ memory {
+ device_type = "memory";
+ reg = <0x00000000 0x40000000>;
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,115200n8 earlyprintk";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-0 = <&pmx_gpio_0 &pmx_gpio_1 &pmx_gpio_2>;
+ pinctrl-names = "default";
+
+ wlan-ap {
+ label = "wlan-ap";
+ gpios = <&gpio0 0 1>;
+ };
+
+ wlan-act {
+ label = "wlan-act";
+ gpios = <&gpio0 1 1>;
+ };
+
+ bluetooth-act {
+ label = "bt-act";
+ gpios = <&gpio0 2 1>;
+ };
+ };
+};
+
+&uart0 { status = "okay"; };
+&sata0 { status = "okay"; };
+&i2c0 { status = "okay"; };
+&mdio { status = "okay"; };
+&eth { status = "okay"; };
+
+/* Samsung M8G2F eMMC */
+&sdio0 {
+ status = "okay";
+ non-removable;
+ bus-width = <4>;
+};
+
+/* Marvell SD8787 WLAN/BT */
+&sdio1 {
+ status = "okay";
+ non-removable;
+ bus-width = <4>;
+};
+
+&spi0 {
+ status = "okay";
+
+ /* spi0.0: 4M Flash Macronix MX25L3205D */
+ spi-flash@0 {
+ compatible = "st,m25l3205d";
+ spi-max-frequency = <20000000>;
+ reg = <0>;
+ };
+};
diff --git a/arch/arm/boot/dts/dove.dtsi b/arch/arm/boot/dts/dove.dtsi
index 8d5be1e8..cc27916 100644
--- a/arch/arm/boot/dts/dove.dtsi
+++ b/arch/arm/boot/dts/dove.dtsi
@@ -10,6 +10,23 @@
gpio2 = &gpio2;
};
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu0: cpu@0 {
+ compatible = "marvell,pj4a", "marvell,sheeva-v7";
+ device_type = "cpu";
+ next-level-cache = <&l2>;
+ reg = <0>;
+ };
+ };
+
+ l2: l2-cache {
+ compatible = "marvell,tauros2-cache";
+ marvell,tauros2-cache-features = <0>;
+ };
+
soc@f1000000 {
compatible = "simple-bus";
#address-cells = <1>;
@@ -25,11 +42,6 @@
0xf2100000 0xf2100000 0x0100000 /* PCIe0 I/O 1M */
0xf8000000 0xf8000000 0x8000000>; /* BootROM 128M */
- l2: l2-cache {
- compatible = "marvell,tauros2-cache";
- marvell,tauros2-cache-features = <0>;
- };
-
timer: timer@20300 {
compatible = "marvell,orion-timer";
reg = <0x20300 0x20>;
@@ -60,14 +72,14 @@
#clock-cells = <1>;
};
- gate_clk: clock-gating-control@d0038 {
+ gate_clk: clock-gating-ctrl@d0038 {
compatible = "marvell,dove-gating-clock";
reg = <0xd0038 0x4>;
clocks = <&core_clk 0>;
#clock-cells = <1>;
};
- thermal: thermal@d001c {
+ thermal: thermal-diode@d001c {
compatible = "marvell,dove-thermal";
reg = <0xd001c 0x0c>, <0xd005c 0x08>;
};
@@ -87,6 +99,8 @@
reg-shift = <2>;
interrupts = <8>;
clocks = <&core_clk 0>;
+ pinctrl-0 = <&pmx_uart1>;
+ pinctrl-names = "default";
status = "disabled";
};
@@ -108,7 +122,7 @@
status = "disabled";
};
- gpio0: gpio@d0400 {
+ gpio0: gpio-ctrl@d0400 {
compatible = "marvell,orion-gpio";
#gpio-cells = <2>;
gpio-controller;
@@ -119,7 +133,7 @@
interrupts = <12>, <13>, <14>, <60>;
};
- gpio1: gpio@d0420 {
+ gpio1: gpio-ctrl@d0420 {
compatible = "marvell,orion-gpio";
#gpio-cells = <2>;
gpio-controller;
@@ -130,7 +144,7 @@
interrupts = <61>;
};
- gpio2: gpio@e8400 {
+ gpio2: gpio-ctrl@e8400 {
compatible = "marvell,orion-gpio";
#gpio-cells = <2>;
gpio-controller;
@@ -138,13 +152,188 @@
ngpios = <8>;
};
- pinctrl: pinctrl@d0200 {
+ pinctrl: pin-ctrl@d0200 {
compatible = "marvell,dove-pinctrl";
reg = <0xd0200 0x10>;
clocks = <&gate_clk 22>;
+
+ pmx_gpio_0: pmx-gpio-0 {
+ marvell,pins = "mpp0";
+ marvell,function = "gpio";
+ };
+
+ pmx_gpio_1: pmx-gpio-1 {
+ marvell,pins = "mpp1";
+ marvell,function = "gpio";
+ };
+
+ pmx_gpio_2: pmx-gpio-2 {
+ marvell,pins = "mpp2";
+ marvell,function = "gpio";
+ };
+
+ pmx_gpio_3: pmx-gpio-3 {
+ marvell,pins = "mpp3";
+ marvell,function = "gpio";
+ };
+
+ pmx_gpio_4: pmx-gpio-4 {
+ marvell,pins = "mpp4";
+ marvell,function = "gpio";
+ };
+
+ pmx_gpio_5: pmx-gpio-5 {
+ marvell,pins = "mpp5";
+ marvell,function = "gpio";
+ };
+
+ pmx_gpio_6: pmx-gpio-6 {
+ marvell,pins = "mpp6";
+ marvell,function = "gpio";
+ };
+
+ pmx_gpio_7: pmx-gpio-7 {
+ marvell,pins = "mpp7";
+ marvell,function = "gpio";
+ };
+
+ pmx_gpio_8: pmx-gpio-8 {
+ marvell,pins = "mpp8";
+ marvell,function = "gpio";
+ };
+
+ pmx_gpio_9: pmx-gpio-9 {
+ marvell,pins = "mpp9";
+ marvell,function = "gpio";
+ };
+
+ pmx_gpio_10: pmx-gpio-10 {
+ marvell,pins = "mpp10";
+ marvell,function = "gpio";
+ };
+
+ pmx_gpio_11: pmx-gpio-11 {
+ marvell,pins = "mpp11";
+ marvell,function = "gpio";
+ };
+
+ pmx_gpio_12: pmx-gpio-12 {
+ marvell,pins = "mpp12";
+ marvell,function = "gpio";
+ };
+
+ pmx_gpio_13: pmx-gpio-13 {
+ marvell,pins = "mpp13";
+ marvell,function = "gpio";
+ };
+
+ pmx_gpio_14: pmx-gpio-14 {
+ marvell,pins = "mpp14";
+ marvell,function = "gpio";
+ };
+
+ pmx_gpio_15: pmx-gpio-15 {
+ marvell,pins = "mpp15";
+ marvell,function = "gpio";
+ };
+
+ pmx_gpio_16: pmx-gpio-16 {
+ marvell,pins = "mpp16";
+ marvell,function = "gpio";
+ };
+
+ pmx_gpio_17: pmx-gpio-17 {
+ marvell,pins = "mpp17";
+ marvell,function = "gpio";
+ };
+
+ pmx_gpio_18: pmx-gpio-18 {
+ marvell,pins = "mpp18";
+ marvell,function = "gpio";
+ };
+
+ pmx_gpio_19: pmx-gpio-19 {
+ marvell,pins = "mpp19";
+ marvell,function = "gpio";
+ };
+
+ pmx_gpio_20: pmx-gpio-20 {
+ marvell,pins = "mpp20";
+ marvell,function = "gpio";
+ };
+
+ pmx_gpio_21: pmx-gpio-21 {
+ marvell,pins = "mpp21";
+ marvell,function = "gpio";
+ };
+
+ pmx_camera: pmx-camera {
+ marvell,pins = "mpp_camera";
+ marvell,function = "camera";
+ };
+
+ pmx_camera_gpio: pmx-camera-gpio {
+ marvell,pins = "mpp_camera";
+ marvell,function = "gpio";
+ };
+
+ pmx_sdio0: pmx-sdio0 {
+ marvell,pins = "mpp_sdio0";
+ marvell,function = "sdio0";
+ };
+
+ pmx_sdio0_gpio: pmx-sdio0-gpio {
+ marvell,pins = "mpp_sdio0";
+ marvell,function = "gpio";
+ };
+
+ pmx_sdio1: pmx-sdio1 {
+ marvell,pins = "mpp_sdio1";
+ marvell,function = "sdio1";
+ };
+
+ pmx_sdio1_gpio: pmx-sdio1-gpio {
+ marvell,pins = "mpp_sdio1";
+ marvell,function = "gpio";
+ };
+
+ pmx_audio1_gpio: pmx-audio1-gpio {
+ marvell,pins = "mpp_audio1";
+ marvell,function = "gpio";
+ };
+
+ pmx_spi0: pmx-spi0 {
+ marvell,pins = "mpp_spi0";
+ marvell,function = "spi0";
+ };
+
+ pmx_spi0_gpio: pmx-spi0-gpio {
+ marvell,pins = "mpp_spi0";
+ marvell,function = "gpio";
+ };
+
+ pmx_uart1: pmx-uart1 {
+ marvell,pins = "mpp_uart1";
+ marvell,function = "uart1";
+ };
+
+ pmx_uart1_gpio: pmx-uart1-gpio {
+ marvell,pins = "mpp_uart1";
+ marvell,function = "gpio";
+ };
+
+ pmx_nand: pmx-nand {
+ marvell,pins = "mpp_nand";
+ marvell,function = "nand";
+ };
+
+ pmx_nand_gpo: pmx-nand-gpo {
+ marvell,pins = "mpp_nand";
+ marvell,function = "gpo";
+ };
};
- spi0: spi@10600 {
+ spi0: spi-ctrl@10600 {
compatible = "marvell,orion-spi";
#address-cells = <1>;
#size-cells = <0>;
@@ -152,10 +341,12 @@
interrupts = <6>;
reg = <0x10600 0x28>;
clocks = <&core_clk 0>;
+ pinctrl-0 = <&pmx_spi0>;
+ pinctrl-names = "default";
status = "disabled";
};
- spi1: spi@14600 {
+ spi1: spi-ctrl@14600 {
compatible = "marvell,orion-spi";
#address-cells = <1>;
#size-cells = <0>;
@@ -166,7 +357,7 @@
status = "disabled";
};
- i2c0: i2c@11000 {
+ i2c0: i2c-ctrl@11000 {
compatible = "marvell,mv64xxx-i2c";
reg = <0x11000 0x20>;
#address-cells = <1>;
@@ -194,23 +385,27 @@
status = "okay";
};
- sdio0: sdio@92000 {
+ sdio0: sdio-host@92000 {
compatible = "marvell,dove-sdhci";
reg = <0x92000 0x100>;
interrupts = <35>, <37>;
clocks = <&gate_clk 8>;
+ pinctrl-0 = <&pmx_sdio0>;
+ pinctrl-names = "default";
status = "disabled";
};
- sdio1: sdio@90000 {
+ sdio1: sdio-host@90000 {
compatible = "marvell,dove-sdhci";
reg = <0x90000 0x100>;
interrupts = <36>, <38>;
clocks = <&gate_clk 9>;
+ pinctrl-0 = <&pmx_sdio1>;
+ pinctrl-names = "default";
status = "disabled";
};
- sata0: sata@a0000 {
+ sata0: sata-host@a0000 {
compatible = "marvell,orion-sata";
reg = <0xa0000 0x2400>;
interrupts = <62>;
@@ -219,12 +414,12 @@
status = "disabled";
};
- rtc@d8500 {
+ rtc: real-time-clock@d8500 {
compatible = "marvell,orion-rtc";
reg = <0xd8500 0x20>;
};
- crypto: crypto@30000 {
+ crypto: crypto-engine@30000 {
compatible = "marvell,orion-crypto";
reg = <0x30000 0x10000>,
<0xc8000000 0x800>;
diff --git a/arch/arm/boot/dts/kirkwood-mv88f6281gtw-ge.dts b/arch/arm/boot/dts/kirkwood-mv88f6281gtw-ge.dts
new file mode 100644
index 0000000..6317e1d
--- /dev/null
+++ b/arch/arm/boot/dts/kirkwood-mv88f6281gtw-ge.dts
@@ -0,0 +1,125 @@
+/*
+ * Marvell 88F6281 GTW GE Board
+ *
+ * Lennert Buytenhek <buytenh@marvell.com>
+ * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ *
+ * This file contains the definitions that are common between the 6281
+ * and 6282 variants of the Marvell Kirkwood Development Board.
+ */
+
+/dts-v1/;
+
+#include "kirkwood.dtsi"
+#include "kirkwood-6281.dtsi"
+
+/ {
+ model = "Marvell 88F6281 GTW GE Board";
+ compatible = "marvell,mv88f6281gtw-ge", "marvell,kirkwood-88f6281", "marvell,kirkwood";
+
+ memory {
+ device_type = "memory";
+ reg = <0x00000000 0x20000000>; /* 512 MB */
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,115200n8 earlyprintk";
+ };
+
+ ocp@f1000000 {
+ pinctrl@10000 {
+ pmx_usb_led: pmx-usb-led {
+ marvell,pins = "mpp12";
+ marvell,function = "gpo";
+ };
+
+ pmx_leds: pmx-leds {
+ marvell,pins = "mpp20", "mpp21";
+ marvell,function = "gpio";
+ };
+
+ pmx_keys: pmx-keys {
+ marvell,pins = "mpp46", "mpp47";
+ marvell,function = "gpio";
+ };
+ };
+
+ spi@10600 {
+ pinctrl-0 = <&pmx_spi>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "mx25l12805d";
+ reg = <0>;
+ spi-max-frequency = <50000000>;
+ mode = <0>;
+ };
+ };
+
+ serial@12000 {
+ pinctrl-0 = <&pmx_uart0>;
+ pinctrl-names = "default";
+ clock-frequency = <200000000>;
+ status = "ok";
+ };
+
+ ehci@50000 {
+ status = "okay";
+ };
+
+ pcie-controller {
+ status = "okay";
+
+ pcie@1,0 {
+ status = "okay";
+ };
+ };
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+ pinctrl-0 = <&pmx_leds &pmx_usb_led>;
+ pinctrl-names = "default";
+
+ green-status {
+ label = "gtw:green:Status";
+ gpios = <&gpio0 20 0>;
+ };
+
+ red-status {
+ label = "gtw:red:Status";
+ gpios = <&gpio0 21 0>;
+ };
+
+ green-usb {
+ label = "gtw:green:USB";
+ gpios = <&gpio0 12 0>;
+ };
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-0 = <&pmx_keys>;
+ pinctrl-names = "default";
+
+ button@1 {
+ label = "SWR Button";
+ linux,code = <0x198>; /* KEY_RESTART */
+ gpios = <&gpio1 15 1>;
+ };
+ button@2 {
+ label = "WPS Button";
+ linux,code = <0x211>; /* KEY_WPS_BUTTON */
+ gpios = <&gpio1 14 1>;
+ };
+ };
+};
diff --git a/arch/arm/configs/kirkwood_defconfig b/arch/arm/configs/kirkwood_defconfig
index b180588..e3f667a 100644
--- a/arch/arm/configs/kirkwood_defconfig
+++ b/arch/arm/configs/kirkwood_defconfig
@@ -10,26 +10,18 @@ CONFIG_MODULE_UNLOAD=y
# CONFIG_BLK_DEV_BSG is not set
CONFIG_ARCH_KIRKWOOD=y
CONFIG_MACH_D2NET_V2=y
-CONFIG_MACH_DB88F6281_BP=y
-CONFIG_MACH_DOCKSTAR=y
-CONFIG_MACH_ESATA_SHEEVAPLUG=y
-CONFIG_MACH_GURUPLUG=y
-CONFIG_MACH_INETSPACE_V2=y
-CONFIG_MACH_MV88F6281GTW_GE=y
CONFIG_MACH_NET2BIG_V2=y
CONFIG_MACH_NET5BIG_V2=y
-CONFIG_MACH_NETSPACE_MAX_V2=y
-CONFIG_MACH_NETSPACE_V2=y
CONFIG_MACH_OPENRD_BASE=y
CONFIG_MACH_OPENRD_CLIENT=y
CONFIG_MACH_OPENRD_ULTIMATE=y
CONFIG_MACH_RD88F6192_NAS=y
CONFIG_MACH_RD88F6281=y
-CONFIG_MACH_SHEEVAPLUG=y
CONFIG_MACH_T5325=y
CONFIG_MACH_TS219=y
CONFIG_MACH_TS41X=y
-CONFIG_MACH_DLINK_KIRKWOOD_DT=y
+CONFIG_ARCH_KIRKWOOD_DT=y
+CONFIG_MACH_MV88F6281GTW_GE_DT=y
# CONFIG_CPU_FEROCEON_OLD_ID is not set
CONFIG_PCI_MVEBU=y
CONFIG_PREEMPT=y
@@ -77,7 +69,6 @@ CONFIG_ATA=y
CONFIG_SATA_AHCI=y
CONFIG_SATA_MV=y
CONFIG_NETDEVICES=y
-CONFIG_MII=y
CONFIG_NET_DSA_MV88E6123_61_65=y
CONFIG_MV643XX_ETH=y
CONFIG_MARVELL_PHY=y
@@ -102,7 +93,6 @@ CONFIG_SPI_ORION=y
CONFIG_GPIO_SYSFS=y
# CONFIG_HWMON is not set
CONFIG_THERMAL=y
-CONFIG_KIRKWOOD_THERMAL=y
CONFIG_WATCHDOG=y
CONFIG_ORION_WATCHDOG=y
CONFIG_HID_DRAGONRISE=y
@@ -163,12 +153,12 @@ CONFIG_NLS_CODEPAGE_850=y
CONFIG_NLS_ISO8859_1=y
CONFIG_NLS_ISO8859_2=y
CONFIG_NLS_UTF8=y
-CONFIG_MAGIC_SYSRQ=y
+CONFIG_DEBUG_INFO=y
CONFIG_DEBUG_FS=y
+CONFIG_MAGIC_SYSRQ=y
CONFIG_DEBUG_KERNEL=y
# CONFIG_SCHED_DEBUG is not set
# CONFIG_DEBUG_PREEMPT is not set
-CONFIG_DEBUG_INFO=y
# CONFIG_FTRACE is not set
CONFIG_DEBUG_USER=y
CONFIG_DEBUG_LL=y
diff --git a/arch/arm/mach-kirkwood/Kconfig b/arch/arm/mach-kirkwood/Kconfig
index 60d0896..fe8319a 100644
--- a/arch/arm/mach-kirkwood/Kconfig
+++ b/arch/arm/mach-kirkwood/Kconfig
@@ -12,41 +12,6 @@ config MACH_D2NET_V2
Say 'Y' here if you want your kernel to support the
LaCie d2 Network v2 NAS.
-config MACH_DOCKSTAR
- bool "Seagate FreeAgent DockStar"
- select KIRKWOOD_LEGACY
- help
- Say 'Y' here if you want your kernel to support the
- Seagate FreeAgent DockStar.
-
-config MACH_ESATA_SHEEVAPLUG
- bool "Marvell eSATA SheevaPlug Reference Board"
- select KIRKWOOD_LEGACY
- help
- Say 'Y' here if you want your kernel to support the
- Marvell eSATA SheevaPlug Reference Board.
-
-config MACH_GURUPLUG
- bool "Marvell GuruPlug Reference Board"
- select KIRKWOOD_LEGACY
- help
- Say 'Y' here if you want your kernel to support the
- Marvell GuruPlug Reference Board.
-
-config MACH_INETSPACE_V2
- bool "LaCie Internet Space v2 NAS Board"
- select KIRKWOOD_LEGACY
- help
- Say 'Y' here if you want your kernel to support the
- LaCie Internet Space v2 NAS.
-
-config MACH_MV88F6281GTW_GE
- bool "Marvell 88F6281 GTW GE Board"
- select KIRKWOOD_LEGACY
- help
- Say 'Y' here if you want your kernel to support the
- Marvell 88F6281 GTW GE Board.
-
config MACH_NET2BIG_V2
bool "LaCie 2Big Network v2 NAS Board"
select KIRKWOOD_LEGACY
@@ -61,20 +26,6 @@ config MACH_NET5BIG_V2
Say 'Y' here if you want your kernel to support the
LaCie 5Big Network v2 NAS.
-config MACH_NETSPACE_MAX_V2
- bool "LaCie Network Space Max v2 NAS Board"
- select KIRKWOOD_LEGACY
- help
- Say 'Y' here if you want your kernel to support the
- LaCie Network Space Max v2 NAS.
-
-config MACH_NETSPACE_V2
- bool "LaCie Network Space v2 NAS Board"
- select KIRKWOOD_LEGACY
- help
- Say 'Y' here if you want your kernel to support the
- LaCie Network Space v2 NAS.
-
config MACH_OPENRD
select KIRKWOOD_LEGACY
bool
@@ -114,13 +65,6 @@ config MACH_RD88F6281
Say 'Y' here if you want your kernel to support the
Marvell RD-88F6281 Reference Board.
-config MACH_SHEEVAPLUG
- bool "Marvell SheevaPlug Reference Board"
- select KIRKWOOD_LEGACY
- help
- Say 'Y' here if you want your kernel to support the
- Marvell SheevaPlug Reference Board.
-
config MACH_T5325
bool "HP t5325 Thin Client"
select KIRKWOOD_LEGACY
@@ -149,6 +93,7 @@ comment "Device tree entries"
config ARCH_KIRKWOOD_DT
bool "Marvell Kirkwood Flattened Device Tree"
select KIRKWOOD_CLK
+ select OF_IRQ
select ORION_IRQCHIP
select ORION_TIMER
select POWER_SUPPLY
@@ -161,13 +106,12 @@ config ARCH_KIRKWOOD_DT
Say 'Y' here if you want your kernel to support the
Marvell Kirkwood using flattened device tree.
-config MACH_DLINK_KIRKWOOD_DT
- bool "D-Link Kirkwood-based NAS (Flattened Device Tree)"
- select ARCH_KIRKWOOD_DT
+config MACH_MV88F6281GTW_GE_DT
+ bool "Marvell 88F6281 GTW GE Board (Flattened Device Tree)"
+ depends on ARCH_KIRKWOOD_DT
help
Say 'Y' here if you want your kernel to support the
- Kirkwood-based D-Link NASes such as DNS-320 & DNS-325,
- using Flattened Device Tree.
+ Marvell 88F6281 GTW GE Board (Flattened Device Tree).
endmenu
diff --git a/arch/arm/mach-kirkwood/Makefile b/arch/arm/mach-kirkwood/Makefile
index 88e2dd3..d1f8e3d 100644
--- a/arch/arm/mach-kirkwood/Makefile
+++ b/arch/arm/mach-kirkwood/Makefile
@@ -1,22 +1,14 @@
obj-y += common.o pcie.o
obj-$(CONFIG_KIRKWOOD_LEGACY) += irq.o mpp.o
obj-$(CONFIG_MACH_D2NET_V2) += d2net_v2-setup.o lacie_v2-common.o
-obj-$(CONFIG_MACH_DOCKSTAR) += dockstar-setup.o
-obj-$(CONFIG_MACH_ESATA_SHEEVAPLUG) += sheevaplug-setup.o
-obj-$(CONFIG_MACH_GURUPLUG) += guruplug-setup.o
-obj-$(CONFIG_MACH_INETSPACE_V2) += netspace_v2-setup.o lacie_v2-common.o
-obj-$(CONFIG_MACH_MV88F6281GTW_GE) += mv88f6281gtw_ge-setup.o
obj-$(CONFIG_MACH_NET2BIG_V2) += netxbig_v2-setup.o lacie_v2-common.o
obj-$(CONFIG_MACH_NET5BIG_V2) += netxbig_v2-setup.o lacie_v2-common.o
-obj-$(CONFIG_MACH_NETSPACE_MAX_V2) += netspace_v2-setup.o lacie_v2-common.o
-obj-$(CONFIG_MACH_NETSPACE_V2) += netspace_v2-setup.o lacie_v2-common.o
obj-$(CONFIG_MACH_OPENRD) += openrd-setup.o
obj-$(CONFIG_MACH_RD88F6192_NAS) += rd88f6192-nas-setup.o
obj-$(CONFIG_MACH_RD88F6281) += rd88f6281-setup.o
-obj-$(CONFIG_MACH_SHEEVAPLUG) += sheevaplug-setup.o
obj-$(CONFIG_MACH_T5325) += t5325-setup.o
obj-$(CONFIG_MACH_TS219) += ts219-setup.o tsx1x-common.o
obj-$(CONFIG_MACH_TS41X) += ts41x-setup.o tsx1x-common.o
obj-$(CONFIG_ARCH_KIRKWOOD_DT) += board-dt.o
-obj-$(CONFIG_MACH_DLINK_KIRKWOOD_DT) += board-dnskw.o
+obj-$(CONFIG_MACH_MV88F6281GTW_GE_DT) += board-mv88f6281gtw_ge.o
diff --git a/arch/arm/mach-kirkwood/board-dnskw.c b/arch/arm/mach-kirkwood/board-dnskw.c
deleted file mode 100644
index 2af7a95..0000000
--- a/arch/arm/mach-kirkwood/board-dnskw.c
+++ /dev/null
@@ -1,36 +0,0 @@
-/*
- * Copyright 2012 (C), Jamie Lentin <jm@lentin.co.uk>
- *
- * arch/arm/mach-kirkwood/board-dnskw.c
- *
- * D-link DNS-320 & DNS-325 NAS Init for drivers not converted to
- * flattened device tree yet.
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/gpio.h>
-#include "common.h"
-
-/* Register any GPIO for output and set the value */
-static void __init dnskw_gpio_register(unsigned gpio, char *name, int def)
-{
- if (gpio_request(gpio, name) == 0 &&
- gpio_direction_output(gpio, 0) == 0) {
- gpio_set_value(gpio, def);
- if (gpio_export(gpio, 0) != 0)
- pr_err("dnskw: Failed to export GPIO %s\n", name);
- } else
- pr_err("dnskw: Failed to register %s\n", name);
-}
-
-void __init dnskw_init(void)
-{
- /* Set NAS to turn back on after a power failure */
- dnskw_gpio_register(37, "dnskw:power:recover", 1);
-}
diff --git a/arch/arm/mach-kirkwood/board-dt.c b/arch/arm/mach-kirkwood/board-dt.c
index fac0f8e..b1872e9 100644
--- a/arch/arm/mach-kirkwood/board-dt.c
+++ b/arch/arm/mach-kirkwood/board-dt.c
@@ -106,8 +106,8 @@ static void __init kirkwood_dt_init(void)
kexec_reinit = kirkwood_enable_pcie;
#endif
- if (of_machine_is_compatible("dlink,dns-kirkwood"))
- dnskw_init();
+ if (of_machine_is_compatible("marvell,mv88f6281gtw-ge"))
+ mv88f6281gtw_ge_init();
of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL);
}
diff --git a/arch/arm/mach-kirkwood/board-mv88f6281gtw_ge.c b/arch/arm/mach-kirkwood/board-mv88f6281gtw_ge.c
new file mode 100644
index 0000000..ee5eea6
--- /dev/null
+++ b/arch/arm/mach-kirkwood/board-mv88f6281gtw_ge.c
@@ -0,0 +1,50 @@
+/*
+ * arch/arm/mach-kirkwood/board-mv88f6281gtw_ge.c
+ *
+ * Marvell 88F6281 GTW GE Board Setup
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/irq.h>
+#include <linux/timer.h>
+#include <linux/mv643xx_eth.h>
+#include <linux/ethtool.h>
+#include <linux/gpio.h>
+#include <net/dsa.h>
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/pci.h>
+#include <mach/kirkwood.h>
+#include "common.h"
+
+static struct mv643xx_eth_platform_data mv88f6281gtw_ge_ge00_data = {
+ .phy_addr = MV643XX_ETH_PHY_NONE,
+ .speed = SPEED_1000,
+ .duplex = DUPLEX_FULL,
+};
+
+static struct dsa_chip_data mv88f6281gtw_ge_switch_chip_data = {
+ .port_names[0] = "lan1",
+ .port_names[1] = "lan2",
+ .port_names[2] = "lan3",
+ .port_names[3] = "lan4",
+ .port_names[4] = "wan",
+ .port_names[5] = "cpu",
+};
+
+static struct dsa_platform_data mv88f6281gtw_ge_switch_plat_data = {
+ .nr_chips = 1,
+ .chip = &mv88f6281gtw_ge_switch_chip_data,
+};
+
+void __init mv88f6281gtw_ge_init(void)
+{
+ kirkwood_ge00_init(&mv88f6281gtw_ge_ge00_data);
+ kirkwood_ge00_switch_init(&mv88f6281gtw_ge_switch_plat_data, NO_IRQ);
+}
diff --git a/arch/arm/mach-kirkwood/common.h b/arch/arm/mach-kirkwood/common.h
index 9d8caae..1296de9 100644
--- a/arch/arm/mach-kirkwood/common.h
+++ b/arch/arm/mach-kirkwood/common.h
@@ -59,10 +59,10 @@ void kirkwood_restart(enum reboot_mode, const char *);
void kirkwood_clk_init(void);
/* board init functions for boards not fully converted to fdt */
-#ifdef CONFIG_MACH_DLINK_KIRKWOOD_DT
-void dnskw_init(void);
+#ifdef CONFIG_MACH_MV88F6281GTW_GE_DT
+void mv88f6281gtw_ge_init(void);
#else
-static inline void dnskw_init(void) {};
+static inline void mv88f6281gtw_ge_init(void) {};
#endif
/* early init functions not converted to fdt yet */
diff --git a/arch/arm/mach-kirkwood/dockstar-setup.c b/arch/arm/mach-kirkwood/dockstar-setup.c
deleted file mode 100644
index 060ccf9..0000000
--- a/arch/arm/mach-kirkwood/dockstar-setup.c
+++ /dev/null
@@ -1,111 +0,0 @@
-/*
- * arch/arm/mach-kirkwood/dockstar-setup.c
- *
- * Seagate FreeAgent DockStar Setup
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/ata_platform.h>
-#include <linux/mtd/partitions.h>
-#include <linux/mv643xx_eth.h>
-#include <linux/gpio.h>
-#include <linux/leds.h>
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <mach/kirkwood.h>
-#include "common.h"
-#include "mpp.h"
-
-static struct mtd_partition dockstar_nand_parts[] = {
- {
- .name = "u-boot",
- .offset = 0,
- .size = SZ_1M
- }, {
- .name = "uImage",
- .offset = MTDPART_OFS_NXTBLK,
- .size = SZ_4M
- }, {
- .name = "root",
- .offset = MTDPART_OFS_NXTBLK,
- .size = MTDPART_SIZ_FULL
- },
-};
-
-static struct mv643xx_eth_platform_data dockstar_ge00_data = {
- .phy_addr = MV643XX_ETH_PHY_ADDR(0),
-};
-
-static struct gpio_led dockstar_led_pins[] = {
- {
- .name = "dockstar:green:health",
- .default_trigger = "default-on",
- .gpio = 46,
- .active_low = 1,
- },
- {
- .name = "dockstar:orange:misc",
- .default_trigger = "none",
- .gpio = 47,
- .active_low = 1,
- },
-};
-
-static struct gpio_led_platform_data dockstar_led_data = {
- .leds = dockstar_led_pins,
- .num_leds = ARRAY_SIZE(dockstar_led_pins),
-};
-
-static struct platform_device dockstar_leds = {
- .name = "leds-gpio",
- .id = -1,
- .dev = {
- .platform_data = &dockstar_led_data,
- }
-};
-
-static unsigned int dockstar_mpp_config[] __initdata = {
- MPP29_GPIO, /* USB Power Enable */
- MPP46_GPIO, /* LED green */
- MPP47_GPIO, /* LED orange */
- 0
-};
-
-static void __init dockstar_init(void)
-{
- /*
- * Basic setup. Needs to be called early.
- */
- kirkwood_init();
-
- /* setup gpio pin select */
- kirkwood_mpp_conf(dockstar_mpp_config);
-
- kirkwood_uart0_init();
- kirkwood_nand_init(ARRAY_AND_SIZE(dockstar_nand_parts), 25);
-
- if (gpio_request(29, "USB Power Enable") != 0 ||
- gpio_direction_output(29, 1) != 0)
- pr_err("can't set up GPIO 29 (USB Power Enable)\n");
- kirkwood_ehci_init();
-
- kirkwood_ge00_init(&dockstar_ge00_data);
-
- platform_device_register(&dockstar_leds);
-}
-
-MACHINE_START(DOCKSTAR, "Seagate FreeAgent DockStar")
- .atag_offset = 0x100,
- .init_machine = dockstar_init,
- .map_io = kirkwood_map_io,
- .init_early = kirkwood_init_early,
- .init_irq = kirkwood_init_irq,
- .init_time = kirkwood_timer_init,
- .restart = kirkwood_restart,
-MACHINE_END
diff --git a/arch/arm/mach-kirkwood/guruplug-setup.c b/arch/arm/mach-kirkwood/guruplug-setup.c
deleted file mode 100644
index 08dd739..0000000
--- a/arch/arm/mach-kirkwood/guruplug-setup.c
+++ /dev/null
@@ -1,133 +0,0 @@
-/*
- * arch/arm/mach-kirkwood/guruplug-setup.c
- *
- * Marvell GuruPlug Reference Board Setup
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/mtd/partitions.h>
-#include <linux/ata_platform.h>
-#include <linux/mv643xx_eth.h>
-#include <linux/gpio.h>
-#include <linux/leds.h>
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <mach/kirkwood.h>
-#include <linux/platform_data/mmc-mvsdio.h>
-#include "common.h"
-#include "mpp.h"
-
-static struct mtd_partition guruplug_nand_parts[] = {
- {
- .name = "u-boot",
- .offset = 0,
- .size = SZ_1M
- }, {
- .name = "uImage",
- .offset = MTDPART_OFS_NXTBLK,
- .size = SZ_4M
- }, {
- .name = "root",
- .offset = MTDPART_OFS_NXTBLK,
- .size = MTDPART_SIZ_FULL
- },
-};
-
-static struct mv643xx_eth_platform_data guruplug_ge00_data = {
- .phy_addr = MV643XX_ETH_PHY_ADDR(0),
-};
-
-static struct mv643xx_eth_platform_data guruplug_ge01_data = {
- .phy_addr = MV643XX_ETH_PHY_ADDR(1),
-};
-
-static struct mv_sata_platform_data guruplug_sata_data = {
- .n_ports = 1,
-};
-
-static struct mvsdio_platform_data guruplug_mvsdio_data = {
- /* unfortunately the CD signal has not been connected */
- .gpio_card_detect = -1,
- .gpio_write_protect = -1,
-};
-
-static struct gpio_led guruplug_led_pins[] = {
- {
- .name = "guruplug:red:health",
- .gpio = 46,
- .active_low = 1,
- },
- {
- .name = "guruplug:green:health",
- .gpio = 47,
- .active_low = 1,
- },
- {
- .name = "guruplug:red:wmode",
- .gpio = 48,
- .active_low = 1,
- },
- {
- .name = "guruplug:green:wmode",
- .gpio = 49,
- .active_low = 1,
- },
-};
-
-static struct gpio_led_platform_data guruplug_led_data = {
- .leds = guruplug_led_pins,
- .num_leds = ARRAY_SIZE(guruplug_led_pins),
-};
-
-static struct platform_device guruplug_leds = {
- .name = "leds-gpio",
- .id = -1,
- .dev = {
- .platform_data = &guruplug_led_data,
- }
-};
-
-static unsigned int guruplug_mpp_config[] __initdata = {
- MPP46_GPIO, /* M_RLED */
- MPP47_GPIO, /* M_GLED */
- MPP48_GPIO, /* B_RLED */
- MPP49_GPIO, /* B_GLED */
- 0
-};
-
-static void __init guruplug_init(void)
-{
- /*
- * Basic setup. Needs to be called early.
- */
- kirkwood_init();
- kirkwood_mpp_conf(guruplug_mpp_config);
-
- kirkwood_uart0_init();
- kirkwood_nand_init(ARRAY_AND_SIZE(guruplug_nand_parts), 25);
-
- kirkwood_ehci_init();
- kirkwood_ge00_init(&guruplug_ge00_data);
- kirkwood_ge01_init(&guruplug_ge01_data);
- kirkwood_sata_init(&guruplug_sata_data);
- kirkwood_sdio_init(&guruplug_mvsdio_data);
-
- platform_device_register(&guruplug_leds);
-}
-
-MACHINE_START(GURUPLUG, "Marvell GuruPlug Reference Board")
- /* Maintainer: Siddarth Gore <gores@marvell.com> */
- .atag_offset = 0x100,
- .init_machine = guruplug_init,
- .map_io = kirkwood_map_io,
- .init_early = kirkwood_init_early,
- .init_irq = kirkwood_init_irq,
- .init_time = kirkwood_timer_init,
- .restart = kirkwood_restart,
-MACHINE_END
diff --git a/arch/arm/mach-kirkwood/mv88f6281gtw_ge-setup.c b/arch/arm/mach-kirkwood/mv88f6281gtw_ge-setup.c
deleted file mode 100644
index ba384b9..0000000
--- a/arch/arm/mach-kirkwood/mv88f6281gtw_ge-setup.c
+++ /dev/null
@@ -1,172 +0,0 @@
-/*
- * arch/arm/mach-kirkwood/mv88f6281gtw_ge-setup.c
- *
- * Marvell 88F6281 GTW GE Board Setup
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/pci.h>
-#include <linux/irq.h>
-#include <linux/mtd/physmap.h>
-#include <linux/timer.h>
-#include <linux/mv643xx_eth.h>
-#include <linux/ethtool.h>
-#include <linux/gpio.h>
-#include <linux/leds.h>
-#include <linux/input.h>
-#include <linux/gpio_keys.h>
-#include <linux/spi/flash.h>
-#include <linux/spi/spi.h>
-#include <net/dsa.h>
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/pci.h>
-#include <mach/kirkwood.h>
-#include "common.h"
-#include "mpp.h"
-
-static struct mv643xx_eth_platform_data mv88f6281gtw_ge_ge00_data = {
- .phy_addr = MV643XX_ETH_PHY_NONE,
- .speed = SPEED_1000,
- .duplex = DUPLEX_FULL,
-};
-
-static struct dsa_chip_data mv88f6281gtw_ge_switch_chip_data = {
- .port_names[0] = "lan1",
- .port_names[1] = "lan2",
- .port_names[2] = "lan3",
- .port_names[3] = "lan4",
- .port_names[4] = "wan",
- .port_names[5] = "cpu",
-};
-
-static struct dsa_platform_data mv88f6281gtw_ge_switch_plat_data = {
- .nr_chips = 1,
- .chip = &mv88f6281gtw_ge_switch_chip_data,
-};
-
-static const struct flash_platform_data mv88f6281gtw_ge_spi_slave_data = {
- .type = "mx25l12805d",
-};
-
-static struct spi_board_info __initdata mv88f6281gtw_ge_spi_slave_info[] = {
- {
- .modalias = "m25p80",
- .platform_data = &mv88f6281gtw_ge_spi_slave_data,
- .irq = -1,
- .max_speed_hz = 50000000,
- .bus_num = 0,
- .chip_select = 0,
- },
-};
-
-static struct gpio_keys_button mv88f6281gtw_ge_button_pins[] = {
- {
- .code = KEY_RESTART,
- .gpio = 47,
- .desc = "SWR Button",
- .active_low = 1,
- }, {
- .code = KEY_WPS_BUTTON,
- .gpio = 46,
- .desc = "WPS Button",
- .active_low = 1,
- },
-};
-
-static struct gpio_keys_platform_data mv88f6281gtw_ge_button_data = {
- .buttons = mv88f6281gtw_ge_button_pins,
- .nbuttons = ARRAY_SIZE(mv88f6281gtw_ge_button_pins),
-};
-
-static struct platform_device mv88f6281gtw_ge_buttons = {
- .name = "gpio-keys",
- .id = -1,
- .num_resources = 0,
- .dev = {
- .platform_data = &mv88f6281gtw_ge_button_data,
- },
-};
-
-static struct gpio_led mv88f6281gtw_ge_led_pins[] = {
- {
- .name = "gtw:green:Status",
- .gpio = 20,
- .active_low = 0,
- }, {
- .name = "gtw:red:Status",
- .gpio = 21,
- .active_low = 0,
- }, {
- .name = "gtw:green:USB",
- .gpio = 12,
- .active_low = 0,
- },
-};
-
-static struct gpio_led_platform_data mv88f6281gtw_ge_led_data = {
- .leds = mv88f6281gtw_ge_led_pins,
- .num_leds = ARRAY_SIZE(mv88f6281gtw_ge_led_pins),
-};
-
-static struct platform_device mv88f6281gtw_ge_leds = {
- .name = "leds-gpio",
- .id = -1,
- .dev = {
- .platform_data = &mv88f6281gtw_ge_led_data,
- },
-};
-
-static unsigned int mv88f6281gtw_ge_mpp_config[] __initdata = {
- MPP12_GPO, /* Status#_USB pin */
- MPP20_GPIO, /* Status#_GLED pin */
- MPP21_GPIO, /* Status#_RLED pin */
- MPP46_GPIO, /* WPS_Switch pin */
- MPP47_GPIO, /* SW_Init pin */
- 0
-};
-
-static void __init mv88f6281gtw_ge_init(void)
-{
- /*
- * Basic setup. Needs to be called early.
- */
- kirkwood_init();
- kirkwood_mpp_conf(mv88f6281gtw_ge_mpp_config);
-
- kirkwood_ehci_init();
- kirkwood_ge00_init(&mv88f6281gtw_ge_ge00_data);
- kirkwood_ge00_switch_init(&mv88f6281gtw_ge_switch_plat_data, NO_IRQ);
- spi_register_board_info(mv88f6281gtw_ge_spi_slave_info,
- ARRAY_SIZE(mv88f6281gtw_ge_spi_slave_info));
- kirkwood_spi_init();
- kirkwood_uart0_init();
- platform_device_register(&mv88f6281gtw_ge_leds);
- platform_device_register(&mv88f6281gtw_ge_buttons);
-}
-
-static int __init mv88f6281gtw_ge_pci_init(void)
-{
- if (machine_is_mv88f6281gtw_ge())
- kirkwood_pcie_init(KW_PCIE0);
-
- return 0;
-}
-subsys_initcall(mv88f6281gtw_ge_pci_init);
-
-MACHINE_START(MV88F6281GTW_GE, "Marvell 88F6281 GTW GE Board")
- /* Maintainer: Lennert Buytenhek <buytenh@marvell.com> */
- .atag_offset = 0x100,
- .init_machine = mv88f6281gtw_ge_init,
- .map_io = kirkwood_map_io,
- .init_early = kirkwood_init_early,
- .init_irq = kirkwood_init_irq,
- .init_time = kirkwood_timer_init,
- .restart = kirkwood_restart,
-MACHINE_END
diff --git a/arch/arm/mach-kirkwood/netspace_v2-setup.c b/arch/arm/mach-kirkwood/netspace_v2-setup.c
deleted file mode 100644
index 3b70661..0000000
--- a/arch/arm/mach-kirkwood/netspace_v2-setup.c
+++ /dev/null
@@ -1,293 +0,0 @@
-/*
- * arch/arm/mach-kirkwood/netspace_v2-setup.c
- *
- * LaCie Network Space v2 board setup
- *
- * Copyright (C) 2009 Simon Guinot <sguinot@lacie.com>
- * Copyright (C) 2009 Benoît Canet <benoit.canet@gmail.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/ata_platform.h>
-#include <linux/mv643xx_eth.h>
-#include <linux/input.h>
-#include <linux/gpio.h>
-#include <linux/gpio_keys.h>
-#include <linux/leds.h>
-#include <linux/gpio-fan.h>
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <mach/kirkwood.h>
-#include <linux/platform_data/leds-kirkwood-ns2.h>
-#include "common.h"
-#include "mpp.h"
-#include "lacie_v2-common.h"
-
-/*****************************************************************************
- * Ethernet
- ****************************************************************************/
-
-static struct mv643xx_eth_platform_data netspace_v2_ge00_data = {
- .phy_addr = MV643XX_ETH_PHY_ADDR(8),
-};
-
-/*****************************************************************************
- * SATA
- ****************************************************************************/
-
-static struct mv_sata_platform_data netspace_v2_sata_data = {
- .n_ports = 2,
-};
-
-/*****************************************************************************
- * GPIO keys
- ****************************************************************************/
-
-#define NETSPACE_V2_PUSH_BUTTON 32
-
-static struct gpio_keys_button netspace_v2_buttons[] = {
- [0] = {
- .code = KEY_POWER,
- .gpio = NETSPACE_V2_PUSH_BUTTON,
- .desc = "Power push button",
- .active_low = 0,
- },
-};
-
-static struct gpio_keys_platform_data netspace_v2_button_data = {
- .buttons = netspace_v2_buttons,
- .nbuttons = ARRAY_SIZE(netspace_v2_buttons),
-};
-
-static struct platform_device netspace_v2_gpio_buttons = {
- .name = "gpio-keys",
- .id = -1,
- .dev = {
- .platform_data = &netspace_v2_button_data,
- },
-};
-
-/*****************************************************************************
- * GPIO LEDs
- ****************************************************************************/
-
-#define NETSPACE_V2_GPIO_RED_LED 12
-
-static struct gpio_led netspace_v2_gpio_led_pins[] = {
- {
- .name = "ns_v2:red:fail",
- .gpio = NETSPACE_V2_GPIO_RED_LED,
- },
-};
-
-static struct gpio_led_platform_data netspace_v2_gpio_leds_data = {
- .num_leds = ARRAY_SIZE(netspace_v2_gpio_led_pins),
- .leds = netspace_v2_gpio_led_pins,
-};
-
-static struct platform_device netspace_v2_gpio_leds = {
- .name = "leds-gpio",
- .id = -1,
- .dev = {
- .platform_data = &netspace_v2_gpio_leds_data,
- },
-};
-
-/*****************************************************************************
- * Dual-GPIO CPLD LEDs
- ****************************************************************************/
-
-#define NETSPACE_V2_GPIO_BLUE_LED_SLOW 29
-#define NETSPACE_V2_GPIO_BLUE_LED_CMD 30
-
-static struct ns2_led netspace_v2_led_pins[] = {
- {
- .name = "ns_v2:blue:sata",
- .cmd = NETSPACE_V2_GPIO_BLUE_LED_CMD,
- .slow = NETSPACE_V2_GPIO_BLUE_LED_SLOW,
- },
-};
-
-static struct ns2_led_platform_data netspace_v2_leds_data = {
- .num_leds = ARRAY_SIZE(netspace_v2_led_pins),
- .leds = netspace_v2_led_pins,
-};
-
-static struct platform_device netspace_v2_leds = {
- .name = "leds-ns2",
- .id = -1,
- .dev = {
- .platform_data = &netspace_v2_leds_data,
- },
-};
-
-/*****************************************************************************
- * GPIO fan
- ****************************************************************************/
-
-/* Designed for fan 40x40x16: ADDA AD0412LB-D50 6000rpm@12v */
-static struct gpio_fan_speed netspace_max_v2_fan_speed[] = {
- { 0, 0 },
- { 1500, 15 },
- { 1700, 14 },
- { 1800, 13 },
- { 2100, 12 },
- { 3100, 11 },
- { 3300, 10 },
- { 4300, 9 },
- { 5500, 8 },
-};
-
-static unsigned netspace_max_v2_fan_ctrl[] = { 22, 7, 33, 23 };
-
-static struct gpio_fan_alarm netspace_max_v2_fan_alarm = {
- .gpio = 25,
- .active_low = 1,
-};
-
-static struct gpio_fan_platform_data netspace_max_v2_fan_data = {
- .num_ctrl = ARRAY_SIZE(netspace_max_v2_fan_ctrl),
- .ctrl = netspace_max_v2_fan_ctrl,
- .alarm = &netspace_max_v2_fan_alarm,
- .num_speed = ARRAY_SIZE(netspace_max_v2_fan_speed),
- .speed = netspace_max_v2_fan_speed,
-};
-
-static struct platform_device netspace_max_v2_gpio_fan = {
- .name = "gpio-fan",
- .id = -1,
- .dev = {
- .platform_data = &netspace_max_v2_fan_data,
- },
-};
-
-/*****************************************************************************
- * General Setup
- ****************************************************************************/
-
-static unsigned int netspace_v2_mpp_config[] __initdata = {
- MPP0_SPI_SCn,
- MPP1_SPI_MOSI,
- MPP2_SPI_SCK,
- MPP3_SPI_MISO,
- MPP4_NF_IO6,
- MPP5_NF_IO7,
- MPP6_SYSRST_OUTn,
- MPP7_GPO, /* Fan speed (bit 1) */
- MPP8_TW0_SDA,
- MPP9_TW0_SCK,
- MPP10_UART0_TXD,
- MPP11_UART0_RXD,
- MPP12_GPO, /* Red led */
- MPP14_GPIO, /* USB fuse */
- MPP16_GPIO, /* SATA 0 power */
- MPP17_GPIO, /* SATA 1 power */
- MPP18_NF_IO0,
- MPP19_NF_IO1,
- MPP20_SATA1_ACTn,
- MPP21_SATA0_ACTn,
- MPP22_GPIO, /* Fan speed (bit 0) */
- MPP23_GPIO, /* Fan power */
- MPP24_GPIO, /* USB mode select */
- MPP25_GPIO, /* Fan rotation fail */
- MPP26_GPIO, /* USB device vbus */
- MPP28_GPIO, /* USB enable host vbus */
- MPP29_GPIO, /* Blue led (slow register) */
- MPP30_GPIO, /* Blue led (command register) */
- MPP31_GPIO, /* Board power off */
- MPP32_GPIO, /* Power button (0 = Released, 1 = Pushed) */
- MPP33_GPO, /* Fan speed (bit 2) */
- 0
-};
-
-#define NETSPACE_V2_GPIO_POWER_OFF 31
-
-static void netspace_v2_power_off(void)
-{
- gpio_set_value(NETSPACE_V2_GPIO_POWER_OFF, 1);
-}
-
-static void __init netspace_v2_init(void)
-{
- /*
- * Basic setup. Needs to be called early.
- */
- kirkwood_init();
- kirkwood_mpp_conf(netspace_v2_mpp_config);
-
- if (machine_is_netspace_max_v2())
- lacie_v2_hdd_power_init(2);
- else
- lacie_v2_hdd_power_init(1);
-
- kirkwood_ehci_init();
- kirkwood_ge00_init(&netspace_v2_ge00_data);
- kirkwood_sata_init(&netspace_v2_sata_data);
- kirkwood_uart0_init();
- lacie_v2_register_flash();
- lacie_v2_register_i2c_devices();
-
- platform_device_register(&netspace_v2_leds);
- platform_device_register(&netspace_v2_gpio_leds);
- platform_device_register(&netspace_v2_gpio_buttons);
- if (machine_is_netspace_max_v2())
- platform_device_register(&netspace_max_v2_gpio_fan);
-
- if (gpio_request(NETSPACE_V2_GPIO_POWER_OFF, "power-off") == 0 &&
- gpio_direction_output(NETSPACE_V2_GPIO_POWER_OFF, 0) == 0)
- pm_power_off = netspace_v2_power_off;
- else
- pr_err("netspace_v2: failed to configure power-off GPIO\n");
-}
-
-#ifdef CONFIG_MACH_NETSPACE_V2
-MACHINE_START(NETSPACE_V2, "LaCie Network Space v2")
- .atag_offset = 0x100,
- .init_machine = netspace_v2_init,
- .map_io = kirkwood_map_io,
- .init_early = kirkwood_init_early,
- .init_irq = kirkwood_init_irq,
- .init_time = kirkwood_timer_init,
- .restart = kirkwood_restart,
-MACHINE_END
-#endif
-
-#ifdef CONFIG_MACH_INETSPACE_V2
-MACHINE_START(INETSPACE_V2, "LaCie Internet Space v2")
- .atag_offset = 0x100,
- .init_machine = netspace_v2_init,
- .map_io = kirkwood_map_io,
- .init_early = kirkwood_init_early,
- .init_irq = kirkwood_init_irq,
- .init_time = kirkwood_timer_init,
- .restart = kirkwood_restart,
-MACHINE_END
-#endif
-
-#ifdef CONFIG_MACH_NETSPACE_MAX_V2
-MACHINE_START(NETSPACE_MAX_V2, "LaCie Network Space Max v2")
- .atag_offset = 0x100,
- .init_machine = netspace_v2_init,
- .map_io = kirkwood_map_io,
- .init_early = kirkwood_init_early,
- .init_irq = kirkwood_init_irq,
- .init_time = kirkwood_timer_init,
- .restart = kirkwood_restart,
-MACHINE_END
-#endif
diff --git a/arch/arm/mach-kirkwood/openrd-setup.c b/arch/arm/mach-kirkwood/openrd-setup.c
index 6a6eb54..e5cf841 100644
--- a/arch/arm/mach-kirkwood/openrd-setup.c
+++ b/arch/arm/mach-kirkwood/openrd-setup.c
@@ -158,7 +158,8 @@ static void __init openrd_init(void)
kirkwood_mpp_conf(openrd_mpp_config);
kirkwood_uart0_init();
- kirkwood_nand_init(ARRAY_AND_SIZE(openrd_nand_parts), 25);
+ kirkwood_nand_init(openrd_nand_parts, ARRAY_SIZE(openrd_nand_parts),
+ 25);
kirkwood_ehci_init();
diff --git a/arch/arm/mach-kirkwood/rd88f6281-setup.c b/arch/arm/mach-kirkwood/rd88f6281-setup.c
index d242231..5154bd2 100644
--- a/arch/arm/mach-kirkwood/rd88f6281-setup.c
+++ b/arch/arm/mach-kirkwood/rd88f6281-setup.c
@@ -87,7 +87,9 @@ static void __init rd88f6281_init(void)
kirkwood_init();
kirkwood_mpp_conf(rd88f6281_mpp_config);
- kirkwood_nand_init(ARRAY_AND_SIZE(rd88f6281_nand_parts), 25);
+ kirkwood_nand_init(rd88f6281_nand_parts,
+ ARRAY_SIZE(rd88f6281_nand_parts),
+ 25);
kirkwood_ehci_init();
kirkwood_ge00_init(&rd88f6281_ge00_data);
diff --git a/arch/arm/mach-kirkwood/sheevaplug-setup.c b/arch/arm/mach-kirkwood/sheevaplug-setup.c
deleted file mode 100644
index 55b68fa..0000000
--- a/arch/arm/mach-kirkwood/sheevaplug-setup.c
+++ /dev/null
@@ -1,161 +0,0 @@
-/*
- * arch/arm/mach-kirkwood/sheevaplug-setup.c
- *
- * Marvell SheevaPlug Reference Board Setup
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/ata_platform.h>
-#include <linux/mtd/partitions.h>
-#include <linux/mv643xx_eth.h>
-#include <linux/gpio.h>
-#include <linux/leds.h>
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <mach/kirkwood.h>
-#include <linux/platform_data/mmc-mvsdio.h>
-#include "common.h"
-#include "mpp.h"
-
-static struct mtd_partition sheevaplug_nand_parts[] = {
- {
- .name = "u-boot",
- .offset = 0,
- .size = SZ_1M
- }, {
- .name = "uImage",
- .offset = MTDPART_OFS_NXTBLK,
- .size = SZ_4M
- }, {
- .name = "root",
- .offset = MTDPART_OFS_NXTBLK,
- .size = MTDPART_SIZ_FULL
- },
-};
-
-static struct mv643xx_eth_platform_data sheevaplug_ge00_data = {
- .phy_addr = MV643XX_ETH_PHY_ADDR(0),
-};
-
-static struct mv_sata_platform_data sheeva_esata_sata_data = {
- .n_ports = 2,
-};
-
-static struct mvsdio_platform_data sheevaplug_mvsdio_data = {
- /* unfortunately the CD signal has not been connected */
-};
-
-static struct mvsdio_platform_data sheeva_esata_mvsdio_data = {
- .gpio_write_protect = 44, /* MPP44 used as SD write protect */
- .gpio_card_detect = 47, /* MPP47 used as SD card detect */
-};
-
-static struct gpio_led sheevaplug_led_pins[] = {
- {
- .name = "plug:red:misc",
- .default_trigger = "none",
- .gpio = 46,
- .active_low = 1,
- },
- {
- .name = "plug:green:health",
- .default_trigger = "default-on",
- .gpio = 49,
- .active_low = 1,
- },
-};
-
-static struct gpio_led_platform_data sheevaplug_led_data = {
- .leds = sheevaplug_led_pins,
- .num_leds = ARRAY_SIZE(sheevaplug_led_pins),
-};
-
-static struct platform_device sheevaplug_leds = {
- .name = "leds-gpio",
- .id = -1,
- .dev = {
- .platform_data = &sheevaplug_led_data,
- }
-};
-
-static unsigned int sheevaplug_mpp_config[] __initdata = {
- MPP29_GPIO, /* USB Power Enable */
- MPP46_GPIO, /* LED Red */
- MPP49_GPIO, /* LED */
- 0
-};
-
-static unsigned int sheeva_esata_mpp_config[] __initdata = {
- MPP29_GPIO, /* USB Power Enable */
- MPP44_GPIO, /* SD Write Protect */
- MPP47_GPIO, /* SD Card Detect */
- MPP49_GPIO, /* LED Green */
- 0
-};
-
-static void __init sheevaplug_init(void)
-{
- /*
- * Basic setup. Needs to be called early.
- */
- kirkwood_init();
-
- /* setup gpio pin select */
- if (machine_is_esata_sheevaplug())
- kirkwood_mpp_conf(sheeva_esata_mpp_config);
- else
- kirkwood_mpp_conf(sheevaplug_mpp_config);
-
- kirkwood_uart0_init();
- kirkwood_nand_init(ARRAY_AND_SIZE(sheevaplug_nand_parts), 25);
-
- if (gpio_request(29, "USB Power Enable") != 0 ||
- gpio_direction_output(29, 1) != 0)
- pr_err("can't set up GPIO 29 (USB Power Enable)\n");
- kirkwood_ehci_init();
-
- kirkwood_ge00_init(&sheevaplug_ge00_data);
-
- /* honor lower power consumption for plugs with out eSATA */
- if (machine_is_esata_sheevaplug())
- kirkwood_sata_init(&sheeva_esata_sata_data);
-
- /* enable sd wp and sd cd on plugs with esata */
- if (machine_is_esata_sheevaplug())
- kirkwood_sdio_init(&sheeva_esata_mvsdio_data);
- else
- kirkwood_sdio_init(&sheevaplug_mvsdio_data);
-
- platform_device_register(&sheevaplug_leds);
-}
-
-#ifdef CONFIG_MACH_SHEEVAPLUG
-MACHINE_START(SHEEVAPLUG, "Marvell SheevaPlug Reference Board")
- /* Maintainer: shadi Ammouri <shadi@marvell.com> */
- .atag_offset = 0x100,
- .init_machine = sheevaplug_init,
- .map_io = kirkwood_map_io,
- .init_early = kirkwood_init_early,
- .init_irq = kirkwood_init_irq,
- .init_time = kirkwood_timer_init,
- .restart = kirkwood_restart,
-MACHINE_END
-#endif
-
-#ifdef CONFIG_MACH_ESATA_SHEEVAPLUG
-MACHINE_START(ESATA_SHEEVAPLUG, "Marvell eSATA SheevaPlug Reference Board")
- .atag_offset = 0x100,
- .init_machine = sheevaplug_init,
- .map_io = kirkwood_map_io,
- .init_early = kirkwood_init_early,
- .init_irq = kirkwood_init_irq,
- .init_time = kirkwood_timer_init,
- .restart = kirkwood_restart,
-MACHINE_END
-#endif
generated by cgit v0.10.2 at 2024-11-12 07:30:43 (GMT)